From: andrew@lunn.ch (Andrew Lunn)
To: linux-arm-kernel@lists.infradead.org
Subject: Orion DT Pull request for 3.6
Date: Sun, 8 Jul 2012 16:56:15 +0200 [thread overview]
Message-ID: <20120708145615.GA10201@lunn.ch> (raw)
Hi Jason
Here is a pull request for the DT work i've been doing for Orion. I've
tested on Kirkwood, but the generic patches have also been tested on
Dove. Compared to the last post of the patches, i've dropped the
crypto patch, since it was not ready. I also extended the binding
documentation for IRQ handlers at the request of Arnd.
It would be good to pull these into a for-next tree and publish it so
others can build upon them.
Thanks
Andrew
The following changes since commit 6887a4131da3adaab011613776d865f4bcfb5678:
Linux 3.5-rc5 (2012-06-30 16:08:57 -0700)
are available in the git repository at:
https://github.com/lunn/linux.git v3.5-rc5-qnap-dt
for you to fetch changes up to 76a6f95e022f975d3e62b7ecdcba8814712e60c0:
ARM: Kirkwood: Use DT to configure SATA device. (2012-07-05 18:24:40 +0200)
----------------------------------------------------------------
Andrew Lunn (7):
ARM: Orion: DT support for IRQ and GPIO Controllers
SPI: Refactor spi-orion to use SPI framework queue.
I2C: MV64XXX: Add Device Tree support
Kirkwood: Add basic device tree support for QNAP TS219.
ARM: Orion: DTify the watchdog timer.
ATA: sata_mv: Add device tree support
ARM: Kirkwood: Use DT to configure SATA device.
Michael Walle (4):
spi-orion: remove uneeded spi_info
spi-orion: add device tree binding
ARM: kirkwood: use devicetree for orion-spi
ARM: kirkwood: use devicetree for SPI on dreamplug
.../devicetree/bindings/arm/mrvl/intc.txt | 20 ++
Documentation/devicetree/bindings/ata/marvell.txt | 16 ++
.../devicetree/bindings/gpio/mrvl-gpio.txt | 23 ++
Documentation/devicetree/bindings/i2c/mrvl-i2c.txt | 32 ++-
.../devicetree/bindings/spi/spi-orion.txt | 19 ++
.../devicetree/bindings/watchdog/marvel.txt | 14 ++
arch/arm/Kconfig | 1 +
arch/arm/boot/dts/kirkwood-dns320.dts | 5 +
arch/arm/boot/dts/kirkwood-dns325.dts | 5 +
arch/arm/boot/dts/kirkwood-dreamplug.dts | 34 +++
arch/arm/boot/dts/kirkwood-ib62x0.dts | 5 +
arch/arm/boot/dts/kirkwood-ts219-6281.dts | 21 ++
arch/arm/boot/dts/kirkwood-ts219-6282.dts | 21 ++
arch/arm/boot/dts/kirkwood-ts219.dtsi | 77 +++++++
arch/arm/boot/dts/kirkwood.dtsi | 62 ++++++
arch/arm/mach-dove/irq.c | 58 ++---
arch/arm/mach-kirkwood/Kconfig | 14 ++
arch/arm/mach-kirkwood/Makefile | 1 +
arch/arm/mach-kirkwood/Makefile.boot | 1 +
arch/arm/mach-kirkwood/board-dnskw.c | 5 -
arch/arm/mach-kirkwood/board-dreamplug.c | 46 ----
arch/arm/mach-kirkwood/board-dt.c | 20 +-
arch/arm/mach-kirkwood/board-ib62x0.c | 5 -
arch/arm/mach-kirkwood/board-ts219.c | 82 +++++++
arch/arm/mach-kirkwood/common.h | 5 +
arch/arm/mach-kirkwood/irq.c | 38 ++--
arch/arm/mach-mv78xx0/irq.c | 22 +-
arch/arm/mach-orion5x/irq.c | 22 +-
arch/arm/plat-orion/gpio.c | 166 ++++++++++----
arch/arm/plat-orion/include/plat/gpio.h | 16 +-
arch/arm/plat-orion/include/plat/irq.h | 3 +-
arch/arm/plat-orion/irq.c | 40 ++++
drivers/ata/sata_mv.c | 42 ++--
drivers/i2c/busses/i2c-mv64xxx.c | 38 +++-
drivers/spi/spi-orion.c | 231 +++++++-------------
drivers/watchdog/orion_wdt.c | 8 +
36 files changed, 856 insertions(+), 362 deletions(-)
create mode 100644 Documentation/devicetree/bindings/ata/marvell.txt
create mode 100644 Documentation/devicetree/bindings/spi/spi-orion.txt
create mode 100644 Documentation/devicetree/bindings/watchdog/marvel.txt
create mode 100644 arch/arm/boot/dts/kirkwood-ts219-6281.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ts219-6282.dts
create mode 100644 arch/arm/boot/dts/kirkwood-ts219.dtsi
create mode 100644 arch/arm/mach-kirkwood/board-ts219.c
reply other threads:[~2012-07-08 14:56 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120708145615.GA10201@lunn.ch \
--to=andrew@lunn.ch \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).