[PATCH 3/7] ARM: mxs: convert m28evk board to device tree

[marex@denx.de (Marek Vasut)]

Dear Shawn Guo,

> From: Marek Vasut <marex@denx.de>
> 
> Signed-off-by: Marek Vasut <marex@denx.de>
> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
> ---
>  arch/arm/boot/dts/imx28.dtsi |   21 ++++
>  arch/arm/boot/dts/m28evk.dts |  241
> ++++++++++++++++++++++++++++++++++++++++++ arch/arm/mach-mxs/mach-mxs.c | 
>  30 +++++
>  3 files changed, 292 insertions(+), 0 deletions(-)
>  create mode 100644 arch/arm/boot/dts/m28evk.dts
> 
> diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
> index 02e778b..3390607 100644
> --- a/arch/arm/boot/dts/imx28.dtsi
> +++ b/arch/arm/boot/dts/imx28.dtsi
> @@ -232,6 +232,17 @@
>  					fsl,pull-up = <0>;
>  				};
> 
> +				auart0_2pins_a: auart0-2pins at 0 {
> +					reg = <0>;
> +					fsl,pinmux-ids = <
> +						0x3000 /* 
MX28_PAD_AUART0_RX__AUART0_RX */
> +						0x3010 /* 
MX28_PAD_AUART0_TX__AUART0_TX */
> +					>;
> +					fsl,drive-strength = <0>;
> +					fsl,voltage = <1>;
> +					fsl,pull-up = <0>;
> +				};
> +
>  				auart3_pins_a: auart3 at 0 {
>  					reg = <0>;
>  					fsl,pinmux-ids = <
> @@ -373,6 +384,16 @@
>  					fsl,pull-up = <0>;
>  				};
> 
> +				pwm3_pins_a: pwm3 at 0 {
> +					reg = <0>;
> +					fsl,pinmux-ids = <
> +						0x31c0 /* MX28_PAD_PWM3__PWM_3 
*/
> +					>;
> +					fsl,drive-strength = <0>;
> +					fsl,voltage = <1>;
> +					fsl,pull-up = <0>;
> +				};

Drop the pwm3 stuff, it's not used.

> +
>  				lcdif_24bit_pins_a: lcdif-24bit at 0 {
>  					reg = <0>;
>  					fsl,pinmux-ids = <
> diff --git a/arch/arm/boot/dts/m28evk.dts b/arch/arm/boot/dts/m28evk.dts
> new file mode 100644
> index 0000000..0c22792
> --- /dev/null
> +++ b/arch/arm/boot/dts/m28evk.dts
> @@ -0,0 +1,241 @@
> +/*
> + * Copyright (C) 2012 Marek Vasut <marex@denx.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +/include/ "imx28.dtsi"
> +
> +/ {
> +	model = "DENX M28EVK";
> +	compatible = "denx,m28evk", "fsl,imx28";
> +
> +	memory {
> +		reg = <0x40000000 0x08000000>;
> +	};
> +
> +	apb at 80000000 {
> +		apbh at 80000000 {
> +			gpmi-nand at 8000c000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
> +				status = "okay";
> +
> +				partition at 0 {
> +					label = "bootloader";
> +					reg = <0x00000000 0x00300000>;
> +					read-only;
> +				};
> +
> +				partition at 1 {
> +					label = "environment";
> +					reg = <0x00300000 0x00080000>;
> +				};
> +
> +				partition at 2 {
> +					label = "redundant-environment";
> +					reg = <0x00380000 0x00080000>;
> +				};
> +
> +				partition at 3 {
> +					label = "kernel";
> +					reg = <0x00400000 0x00400000>;
> +				};
> +
> +				partition at 4 {
> +					label = "filesystem";
> +					reg = <0x00800000 0x0f800000>;
> +				};
> +			};
> +
> +			ssp0: ssp at 80010000 {
> +				compatible = "fsl,imx28-mmc";
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&mmc0_8bit_pins_a
> +					     &mmc0_cd_cfg
> +					     &mmc0_sck_cfg>;
> +				bus-width = <8>;
> +				wp-gpios = <&gpio3 10 1>;
> +				status = "okay";
> +			};
> +
> +			pinctrl at 80018000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&hog_pins_a>;
> +
> +				hog_pins_a: hog-gpios at 0 {
> +					reg = <0>;
> +					fsl,pinmux-ids = <
> +						0x30a3 /* 
MX28_PAD_AUART2_CTS__GPIO_3_10 */
> +						0x30b3 /* 
MX28_PAD_AUART2_RTS__GPIO_3_11 */
> +						0x3103 /* 
MX28_PAD_PWM0__GPIO_3_16 */
> +						0x3113 /* 
MX28_PAD_PWM1__GPIO_3_17 */

What's this part for ?

> +					>;
> +					fsl,drive-strength = <0>;
> +					fsl,voltage = <1>;
> +					fsl,pull-up = <0>;
> +				};
> +
> +				lcdif_pins_m28: lcdif-m28 at 0 {
> +					reg = <0>;
> +					fsl,pinmux-ids = <
> +						0x11e0 /* 
MX28_PAD_LCD_DOTCLK__LCD_DOTCLK */
> +						0x11f0 /* 
MX28_PAD_LCD_ENABLE__LCD_ENABLE */
> +					>;
> +					fsl,drive-strength = <0>;
> +					fsl,voltage = <1>;
> +					fsl,pull-up = <0>;
> +				};
> +			};
> +
> +			lcdif at 80030000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&lcdif_24bit_pins_a
> +					     &lcdif_pins_m28>;
> +				status = "okay";
> +			};
> +
> +			can0: can at 80032000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&can0_pins_a>;
> +				status = "okay";
> +			};
> +
> +			can1: can at 80034000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&can1_pins_a>;
> +				status = "okay";
> +			};
> +		};
> +
> +		apbx at 80040000 {
> +			saif0: saif at 80042000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&saif0_pins_a>;
> +				status = "okay";
> +			};
> +
> +			saif1: saif at 80046000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&saif1_pins_a>;
> +				fsl,saif-master = <&saif0>;
> +				status = "okay";
> +			};
> +
> +			i2c0: i2c at 80058000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&i2c0_pins_a>;
> +				status = "okay";
> +
> +				sgtl5000: codec at 0a {
> +					compatible = "fsl,sgtl5000";
> +					reg = <0x0a>;
> +					VDDA-supply = <&reg_3p3v>;
> +					VDDIO-supply = <&reg_3p3v>;
> +
> +				};
> +
> +				eeprom: eeprom at 51 {
> +					compatible = "atmel,24c128";
> +					reg = <0x51>;
> +					pagesize = <32>;
> +				};
> +
> +				rtc: rtc at 68 {
> +					compatible = "stm,mt41t62";
> +					reg = <0x68>;
> +				};
> +			};
> +
> +			pwm: pwm at 80064000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&pwm3_pins_a>;
> +				status = "okay";
> +			};
> +
> +			duart: serial at 80074000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&duart_pins_a>;
> +				status = "okay";
> +			};
> +
> +			auart0: serial at 8006a000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&auart0_2pins_a>;
> +				status = "okay";
> +			};
> +
> +			auart3: serial at 80070000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&auart3_pins_a>;
> +				status = "okay";
> +			};
> +		};
> +	};
> +
> +	ahb at 80080000 {
> +		mac0: ethernet at 800f0000 {
> +			phy-mode = "rmii";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mac0_pins_a>;
> +			phy-reset-gpios = <&gpio3 11 0>;
> +			status = "okay";
> +		};
> +
> +		mac1: ethernet at 800f4000 {
> +			phy-mode = "rmii";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mac1_pins_a>;
> +			status = "okay";
> +		};
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";
> +
> +		reg_3p3v: 3p3v {
> +			compatible = "regulator-fixed";
> +			regulator-name = "3P3V";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			regulator-always-on;
> +		};
> +	};
> +
> +	sound {
> +		compatible = "fsl,imx28-evk-sgtl5000",
> +			     "fsl,mxs-audio-sgtl5000";
> +		model = "imx28-evk-sgtl5000";
> +		saif-controllers = <&saif0 &saif1>;
> +		audio-codec = <&sgtl5000>;
> +	};
> +
> +	leds {

Drop the led section, it's some ancient nonsense from who-knows-where :-(

> +		compatible = "gpio-leds";
> +
> +		user1 {
> +			label = "Heartbeat1";
> +			gpios = <&gpio3 16 0>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +
> +		user2 {
> +			label = "Heartbeat2";
> +			gpios = <&gpio3 17 0>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +	};
> +
> +	backlight {

Drop this backlight too please.

> +		compatible = "pwm-backlight";
> +		pwms = <&pwm 3 5000000>;
> +		brightness-levels = <0 4 8 16 32 64 128 255>;
> +		default-brightness-level = <6>;
> +	};
> +};
> diff --git a/arch/arm/mach-mxs/mach-mxs.c b/arch/arm/mach-mxs/mach-mxs.c
> index 7bbb961..6bb6db8 100644
> --- a/arch/arm/mach-mxs/mach-mxs.c
> +++ b/arch/arm/mach-mxs/mach-mxs.c
> @@ -59,6 +59,23 @@ static struct fb_videomode mx28evk_video_modes[] = {
>  	},
>  };
> 
> +static struct fb_videomode m28evk_video_modes[] = {
> +	{
> +		.name		= "Ampire AM-800480R2TMQW-T01H",
> +		.refresh	= 60,
> +		.xres		= 800,
> +		.yres		= 480,
> +		.pixclock	= 30066, /* picosecond (33.26 MHz) */
> +		.left_margin	= 0,
> +		.right_margin	= 256,
> +		.upper_margin	= 0,
> +		.lower_margin	= 45,
> +		.hsync_len	= 1,
> +		.vsync_len	= 1,
> +		.sync		= FB_SYNC_DATA_ENABLE_HIGH_ACT,
> +	},
> +};
> +
>  static struct mxsfb_platform_data mxsfb_pdata __initdata;
> 
>  static struct of_dev_auxdata mxs_auxdata_lookup[] __initdata = {
> @@ -203,12 +220,24 @@ static void __init imx28_evk_init(void)
>  	mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT;
>  }
> 
> +static void __init m28evk_init(void)
> +{
> +	update_fec_mac_prop(OUI_DENX);
> +
> +	mxsfb_pdata.mode_list = m28evk_video_modes;
> +	mxsfb_pdata.mode_count = ARRAY_SIZE(m28evk_video_modes);
> +	mxsfb_pdata.default_bpp = 16;
> +	mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT;
> +}
> +
>  static void __init mxs_machine_init(void)
>  {
>  	if (of_machine_is_compatible("fsl,imx28-evk"))
>  		imx28_evk_init();
>  	else if (of_machine_is_compatible("fsl,imx23-evk"))
>  		imx23_evk_init();
> +	else if (of_machine_is_compatible("denx,m28evk"))
> +		m28evk_init();

I think you need to call imx28_evk_init() here ?

> 
>  	of_platform_populate(NULL, of_default_bus_match_table,
>  			     mxs_auxdata_lookup, NULL);
> @@ -223,6 +252,7 @@ static const char *imx23_dt_compat[] __initdata = {
> 
>  static const char *imx28_dt_compat[] __initdata = {
>  	"crystalfontz,cfa10036",
> +	"denx,m28evk",
>  	"fsl,imx28-evk",
>  	"fsl,imx28",
>  	NULL,