From: broonie@opensource.wolfsonmicro.com (Mark Brown)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 13/18] ARM: ux500: Add ux500 PCM to DB8500 Device Tree
Date: Mon, 30 Jul 2012 16:02:53 +0100 [thread overview]
Message-ID: <20120730150252.GG4468@opensource.wolfsonmicro.com> (raw)
In-Reply-To: <501699B2.7030002@linaro.org>
On Mon, Jul 30, 2012 at 03:26:58PM +0100, Lee Jones wrote:
> On 30/07/12 14:40, Mark Brown wrote:
> >>We use it register the driver for probe()ing. In the same way we do
> >>for the PMU and Regulators. All three of which actually belong to a
> >>different hardware block. Do you know of a better way to register
> >>those devices?
> >You've not identified which of the two cases above we're in... assuming
> >it's a virtal device look at how the DT bindings for the other platforms
> >are doing things.
> I thought it would have been obvious by my response. The PMU seems
> to be a virtual device with no registers or IRQs.
That's not at all obvious, no.
> I've found a DT which seems to do it in the same way as I do
> 'arch/powerpc/boot/dts/p1022ds.dts', but some others call PCM
> registration from the CPU-side DAI probe(). Would that be your
> preference?
Yes, do what the other drivers are doing
next prev parent reply other threads:[~2012-07-30 15:02 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-07-27 12:45 [PATCH 00/18] Configure ux500 Audio Drivers for Device Tree Lee Jones
2012-07-27 12:45 ` [PATCH 01/18] Documentation: Describe the ux500 realated audio related DT nodes Lee Jones
2012-07-29 20:31 ` Mark Brown
2012-07-30 7:38 ` Lee Jones
2012-07-30 13:48 ` Mark Brown
2012-07-30 14:32 ` Lee Jones
2012-07-30 15:07 ` Mark Brown
2012-07-27 12:45 ` [PATCH 02/18] ASoC: Ux500: Move MSP pinctrl setup into the MSP driver Lee Jones
2012-07-27 12:45 ` [PATCH 03/18] ASoC: Ux500: Enable MOP500 driver for Device Tree Lee Jones
2012-07-27 12:45 ` [PATCH 04/18] ASoC: Ux500: Enable ux500 PCM " Lee Jones
2012-07-27 12:45 ` [PATCH 05/18] ASoC: Ux500: Enable ux500 MSP " Lee Jones
2012-07-29 20:42 ` Mark Brown
2012-07-30 6:53 ` Lee Jones
2012-07-30 13:39 ` Mark Brown
2012-07-30 13:57 ` Lee Jones
2012-07-30 15:01 ` Mark Brown
2012-07-27 12:45 ` [PATCH 06/18] ASoC: codecs: Enable AB8500 CODEC " Lee Jones
2012-07-27 12:45 ` [PATCH 07/18] ARM: ux500: Clean-up MSP platform code Lee Jones
2012-07-27 12:45 ` [PATCH 08/18] ARM: ux500: Add AB8500 CODEC node to DB8500 Device Tree Lee Jones
2012-07-27 12:45 ` [PATCH 09/18] ARM: ux500: Fork MSP platform registration for step-by-step DT enablement Lee Jones
2012-07-27 12:45 ` [PATCH 10/18] ARM: ux500: Enable HIGHMEM on all mop500 platforms Lee Jones
2012-07-29 20:45 ` Mark Brown
2012-07-30 6:54 ` Lee Jones
2012-07-27 12:45 ` [PATCH 11/18] ARM: ux500: Pass MSP DMA platform data though AUXDATA Lee Jones
2012-07-27 12:45 ` [PATCH 12/18] ARM: ux500: Stop registering the MOP500 Audio driver from platform code Lee Jones
2012-07-27 12:45 ` [PATCH 13/18] ARM: ux500: Add ux500 PCM to DB8500 Device Tree Lee Jones
2012-07-29 20:50 ` Mark Brown
2012-07-30 7:32 ` Lee Jones
2012-07-30 13:40 ` Mark Brown
2012-07-30 14:26 ` Lee Jones
2012-07-30 15:02 ` Mark Brown [this message]
2012-07-27 12:45 ` [PATCH 14/18] ARM: ux500: Stop registering the PCM driver from platform code Lee Jones
2012-07-27 12:45 ` [PATCH 15/18] ARM: ux500: Add MSP devices to DB8500 Device Tree Lee Jones
2012-07-27 12:46 ` [PATCH 16/18] ARM: ux500: Remove platform registration of MSP devices Lee Jones
2012-07-27 12:46 ` [PATCH 17/18] ARM: ux500: Add all encompassing Sound node to DB8500 Device Tree Lee Jones
2012-07-29 20:52 ` Mark Brown
2012-07-30 7:35 ` Lee Jones
2012-07-30 13:42 ` Mark Brown
2012-07-30 14:30 ` Lee Jones
2012-07-27 12:46 ` [PATCH 18/18] ARM: ux500: Rename MSP board file to something more meaningful Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120730150252.GG4468@opensource.wolfsonmicro.com \
--to=broonie@opensource.wolfsonmicro.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).