[alsa-devel] [PATCH 0/3] ASoC: Davinci: McASP: add support new McASP IP Variant

[mporter@ti.com (Matt Porter)]

On Wed, Oct 03, 2012 at 04:07:41PM +0200, Daniel Mack wrote:
> On 03.10.2012 14:57, Hebbar, Gururaja wrote:
> > On Wed, Oct 03, 2012 at 16:46:39, Daniel Mack wrote:
> >> On 03.10.2012 09:16, Hebbar, Gururaja wrote:
> >>> On Wed, Oct 03, 2012 at 03:58:45, Daniel Mack wrote:
> >>>> On 31.08.2012 14:50, Hebbar, Gururaja wrote:
> >>>>> The OMAP2+ variant of McASP is different from Davinci variant w.r.to some
> >>>>> register offset and missing generic SRAM APIs support
> >>>>>
> >>>>> Changes
> >>>>> - Add new MCASP_VERSION_3 to identify new variant. New DT compatible
> >>>>>   "ti,omap2-mcasp-audio" to identify version 3 controller.
> >>>>> - The register offsets are handled depending on the version.
> >>>>> - Provide a config option to indicate missing SRAM API support.
> >>>>
> >>>> Could you give some insight which hardware this was tested on? I'm
> >>>> trying to get this up and running on a AM33xx board, and the patches
> >>>> look all reasonable to me. My problem is that I can't make the DMA
> >>>> engine move forward, I fail to receive a single interrupt on this
> >>>> peripheral after the stream starts. I will continue searching for the
> >>>> reason of this tomorrow, but maybe you can give me some hint by
> >>>> explaining your setup?
> >>>>
> >>>> Note that I'm using your patches together with Matt's from this series:
> >>>>
> >>>>   https://github.com/ohporter/linux/tree/edma-dmaengine-am33xx-rfc-v1
> >>>>
> >>>> ... but it doesn't work without those either.
> >>>
> >>>
> >>> When I started working on adding DT support to McASP driver, Matt Porter 
> >>> EDMA port was not yet ready. 
> >>>
> >>> So 
> >>> 1. I took existing edma driver from AM335x Arago release [1] (driver + edma 
> >>>    device init). 
> >>> 2. Added this to Vaibhav's Local (linux-next + AM335x patches) tree [2] 
> >>>
> >>> 3. Added DT support to McASP driver.
> >>>
> >>> I tested this on AM335x EVM board. 
> >>
> >> Hmm, so I think there's a tiny bit missing for the EDMA conversion on DT
> >> kernels.
> >>
> >>> If you need the code, I can share it as a patch (I will send the patch as a 
> >>> private mail since the patch is huge).
> >>
> >> Please do :) Or just push your entire tree somewhere.
> > 
> > I have pushed the code at below git repo
> > Repo :https://github.com/hvaibhav/am335x-linux
> > Branch : am335x-upstream-staging-audio
> > 
> > This includes 
> > 1. (linux-next + AM335x patches)
> > 2. McASP DT conversion
> > 3. EDMA hack
> > 4. AM335x audio specific DT blobs
> > 5. Am335x dma DT blobs [hack]
> 
> Ha, that 5th point was what I was missing, in particular these DMA
> offset matching bits. Thanks a lot! I'll get back to you soon with some
> patches for the mcasp driver.

You should be able to replace #3 with https://lkml.org/lkml/2012/9/20/275
The intention is for McASP to use the private EDMA API on both DaVinci
and AM33xx until the dmaengine conversion of McASP is ready. 

-Matt