[PATCH v4 7/7] ARM: davinci: register pruss_uio device on DA850 EVM

[mporter@ti.com (Matt Porter)]

On Mon, Oct 08, 2012 at 04:23:05PM +0530, Sekhar Nori wrote:
> On 10/5/2012 10:34 PM, Matt Porter wrote:
> > Configures the required pdata and registers the pruss_uio
> > platform device on the DA850 EVM.
> > 
> > Tested on AM180x-EVM using the PRU_memAccessPRUDataRam and
> > PRU_memAccessL3andDDR examples from the PRU userspace tools
> > available from http://www.ti.com/tool/sprc940
> > 
> > Signed-off-by: Matt Porter <mporter@ti.com>
> > ---
> >  arch/arm/mach-davinci/board-da850-evm.c |   12 ++++++++++++
> >  1 file changed, 12 insertions(+)
> > 
> > diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
> > index 7359375..6f9478b 100644
> > --- a/arch/arm/mach-davinci/board-da850-evm.c
> > +++ b/arch/arm/mach-davinci/board-da850-evm.c
> > @@ -31,6 +31,7 @@
> >  #include <linux/platform_data/mtd-davinci.h>
> >  #include <linux/platform_data/mtd-davinci-aemif.h>
> >  #include <linux/platform_data/spi-davinci.h>
> > +#include <linux/platform_data/uio_pruss.h>
> >  #include <linux/regulator/machine.h>
> >  #include <linux/regulator/tps6507x.h>
> >  #include <linux/spi/spi.h>
> > @@ -40,6 +41,7 @@
> >  #include <mach/cp_intc.h>
> >  #include <mach/da8xx.h>
> >  #include <mach/mux.h>
> > +#include <mach/sram.h>
> >  
> >  #include <asm/mach-types.h>
> >  #include <asm/mach/arch.h>
> > @@ -1253,6 +1255,10 @@ static __init int da850_wl12xx_init(void)
> >  
> >  #endif /* CONFIG_DA850_WL12XX */
> >  
> > +struct uio_pruss_pdata da8xx_pruss_uio_pdata = {
> > +	.pintc_base	= 0x4000,
> > +};
> > +
> >  #define DA850EVM_SATA_REFCLKPN_RATE	(100 * 1000 * 1000)
> >  
> >  static __init void da850_evm_init(void)
> > @@ -1339,6 +1345,12 @@ static __init void da850_evm_init(void)
> >  		pr_warning("da850_evm_init: lcdcntl mux setup failed: %d\n",
> >  				ret);
> >  
> > +	da8xx_pruss_uio_pdata.sram_pool = sram_get_gen_pool();
> > +	ret = da8xx_register_pruss_uio(&da8xx_pruss_uio_pdata);
> > +	if (ret)
> > +		pr_warning("pruss_uio initialization failed: %d\n",
> > +				ret);
> 
> I failed to mention this last time around, but is there any reason
> platform data will change from board to board? Looks like the pintc_base
> is SoC specific and that all platforms would use SRAM when using the
> pruss driver. Looks like you can make da8xx_register_pruss_uio() take no
> parameters at all.

No reason, just oversight here. I'll update these two patches so this is
done at the SoC level.

-Matt