* [PATCH v2] i2c: omap: re-factor omap_i2c_init function
2012-10-25 6:36 [PATCH v2] i2c: omap: re-factor omap_i2c_init function Shubhrajyoti D
@ 2012-10-25 6:36 ` Felipe Balbi
2012-10-25 6:53 ` Shubhrajyoti Datta
2012-10-25 9:34 ` Shubhrajyoti Datta
0 siblings, 2 replies; 6+ messages in thread
From: Felipe Balbi @ 2012-10-25 6:36 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Thu, Oct 25, 2012 at 12:06:51PM +0530, Shubhrajyoti D wrote:
> re-factor omap_i2c_init() so that we can re-use it for resume.
> While at it also remove the bufstate variable as we write it
> in omap_i2c_resize_fifo for every transfer.
>
> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
> ---
> v2 - add the iestate 0 check back.
> - Remove a stray change.
> - Applies on top of Felipe's patches.
> http://www.spinics.net/lists/linux-omap/msg79995.html
>
>
> Tested with Terro sys fix + Felipe's stop sched_clock() during suspend
> on omap3636 beagle both idle and suspend.
>
> Functional testing on omap4sdp.
>
> drivers/i2c/busses/i2c-omap.c | 71 ++++++++++++++++++----------------------
> 1 files changed, 32 insertions(+), 39 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> index 5e5cefb..3d400b1 100644
> --- a/drivers/i2c/busses/i2c-omap.c
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -209,7 +209,6 @@ struct omap_i2c_dev {
> u16 pscstate;
> u16 scllstate;
> u16 sclhstate;
> - u16 bufstate;
> u16 syscstate;
> u16 westate;
> u16 errata;
> @@ -285,9 +284,31 @@ static inline u16 omap_i2c_read_reg(struct omap_i2c_dev *i2c_dev, int reg)
> }
> }
>
> +static void __omap_i2c_init(struct omap_i2c_dev *dev)
> +{
> +
> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
> + /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */
> + omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, dev->pscstate);
> +
> + /* SCL low and high time values */
> + omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG, dev->scllstate);
> + omap_i2c_write_reg(dev, OMAP_I2C_SCLH_REG, dev->sclhstate);
> + if (dev->rev >= OMAP_I2C_REV_ON_3430_3530)
> + omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, dev->westate);
> + /* Take the I2C module out of reset: */
> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
a few blank lines in this function wouldn't hurt and they would help
with readability.
> + /*
> + * Don't write to this register if the IE state is 0 as it can
> + * cause deadlock.
> + */
> + if (dev->iestate)
> + omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate);
> +}
> +
> static int omap_i2c_init(struct omap_i2c_dev *dev)
> {
> - u16 psc = 0, scll = 0, sclh = 0, buf = 0;
> + u16 psc = 0, scll = 0, sclh = 0;
> u16 fsscll = 0, fssclh = 0, hsscll = 0, hssclh = 0;
> unsigned long fclk_rate = 12000000;
> unsigned long timeout;
> @@ -337,11 +358,8 @@ static int omap_i2c_init(struct omap_i2c_dev *dev)
> * REVISIT: Some wkup sources might not be needed.
> */
> dev->westate = OMAP_I2C_WE_ALL;
> - omap_i2c_write_reg(dev, OMAP_I2C_WE_REG,
> - dev->westate);
remove the comment too since now that's done by some other function ?
> }
> }
> - omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
>
> if (dev->flags & OMAP_I2C_FLAG_ALWAYS_ARMXOR_CLK) {
> /*
> @@ -426,28 +444,18 @@ static int omap_i2c_init(struct omap_i2c_dev *dev)
> sclh = fclk_rate / (dev->speed * 2) - 7 + psc;
> }
>
> - /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */
> - omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, psc);
> -
> - /* SCL low and high time values */
> - omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG, scll);
> - omap_i2c_write_reg(dev, OMAP_I2C_SCLH_REG, sclh);
> -
> - /* Take the I2C module out of reset: */
> - omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
> -
> /* Enable interrupts */
> dev->iestate = (OMAP_I2C_IE_XRDY | OMAP_I2C_IE_RRDY |
> OMAP_I2C_IE_NACK | OMAP_I2C_IE_AL) |
> ((dev->fifo_size) ? (OMAP_I2C_IE_RDR |
> OMAP_I2C_IE_XDR) : 0);
> - omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate);
> - if (dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) {
> - dev->pscstate = psc;
> - dev->scllstate = scll;
> - dev->sclhstate = sclh;
> - dev->bufstate = buf;
> - }
> +
> + dev->pscstate = psc;
> + dev->scllstate = scll;
> + dev->sclhstate = sclh;
> +
> + __omap_i2c_init(dev);
> +
> return 0;
> }
>
> @@ -1268,23 +1276,8 @@ static int omap_i2c_runtime_resume(struct device *dev)
> {
> struct omap_i2c_dev *_dev = dev_get_drvdata(dev);
>
> - if (_dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) {
> - omap_i2c_write_reg(_dev, OMAP_I2C_CON_REG, 0);
> - omap_i2c_write_reg(_dev, OMAP_I2C_PSC_REG, _dev->pscstate);
> - omap_i2c_write_reg(_dev, OMAP_I2C_SCLL_REG, _dev->scllstate);
> - omap_i2c_write_reg(_dev, OMAP_I2C_SCLH_REG, _dev->sclhstate);
> - omap_i2c_write_reg(_dev, OMAP_I2C_BUF_REG, _dev->bufstate);
> - omap_i2c_write_reg(_dev, OMAP_I2C_SYSC_REG, _dev->syscstate);
> - omap_i2c_write_reg(_dev, OMAP_I2C_WE_REG, _dev->westate);
> - omap_i2c_write_reg(_dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
> - }
> -
> - /*
> - * Don't write to this register if the IE state is 0 as it can
> - * cause deadlock.
> - */
> - if (_dev->iestate)
> - omap_i2c_write_reg(_dev, OMAP_I2C_IE_REG, _dev->iestate);
> + if (_dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE)
> + __omap_i2c_init(_dev);
>
> return 0;
> }
you continue to miss the changes in omap_i2c_xfer_msg() and your
explanation of why not doing it wasn't good enough IMHO.
--
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20121025/7ee5fe9b/attachment-0001.sig>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v2] i2c: omap: re-factor omap_i2c_init function
@ 2012-10-25 6:36 Shubhrajyoti D
2012-10-25 6:36 ` Felipe Balbi
0 siblings, 1 reply; 6+ messages in thread
From: Shubhrajyoti D @ 2012-10-25 6:36 UTC (permalink / raw)
To: linux-arm-kernel
re-factor omap_i2c_init() so that we can re-use it for resume.
While at it also remove the bufstate variable as we write it
in omap_i2c_resize_fifo for every transfer.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
---
v2 - add the iestate 0 check back.
- Remove a stray change.
- Applies on top of Felipe's patches.
http://www.spinics.net/lists/linux-omap/msg79995.html
Tested with Terro sys fix + Felipe's stop sched_clock() during suspend
on omap3636 beagle both idle and suspend.
Functional testing on omap4sdp.
drivers/i2c/busses/i2c-omap.c | 71 ++++++++++++++++++----------------------
1 files changed, 32 insertions(+), 39 deletions(-)
diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 5e5cefb..3d400b1 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -209,7 +209,6 @@ struct omap_i2c_dev {
u16 pscstate;
u16 scllstate;
u16 sclhstate;
- u16 bufstate;
u16 syscstate;
u16 westate;
u16 errata;
@@ -285,9 +284,31 @@ static inline u16 omap_i2c_read_reg(struct omap_i2c_dev *i2c_dev, int reg)
}
}
+static void __omap_i2c_init(struct omap_i2c_dev *dev)
+{
+
+ omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
+ /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */
+ omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, dev->pscstate);
+
+ /* SCL low and high time values */
+ omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG, dev->scllstate);
+ omap_i2c_write_reg(dev, OMAP_I2C_SCLH_REG, dev->sclhstate);
+ if (dev->rev >= OMAP_I2C_REV_ON_3430_3530)
+ omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, dev->westate);
+ /* Take the I2C module out of reset: */
+ omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
+ /*
+ * Don't write to this register if the IE state is 0 as it can
+ * cause deadlock.
+ */
+ if (dev->iestate)
+ omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate);
+}
+
static int omap_i2c_init(struct omap_i2c_dev *dev)
{
- u16 psc = 0, scll = 0, sclh = 0, buf = 0;
+ u16 psc = 0, scll = 0, sclh = 0;
u16 fsscll = 0, fssclh = 0, hsscll = 0, hssclh = 0;
unsigned long fclk_rate = 12000000;
unsigned long timeout;
@@ -337,11 +358,8 @@ static int omap_i2c_init(struct omap_i2c_dev *dev)
* REVISIT: Some wkup sources might not be needed.
*/
dev->westate = OMAP_I2C_WE_ALL;
- omap_i2c_write_reg(dev, OMAP_I2C_WE_REG,
- dev->westate);
}
}
- omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
if (dev->flags & OMAP_I2C_FLAG_ALWAYS_ARMXOR_CLK) {
/*
@@ -426,28 +444,18 @@ static int omap_i2c_init(struct omap_i2c_dev *dev)
sclh = fclk_rate / (dev->speed * 2) - 7 + psc;
}
- /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */
- omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, psc);
-
- /* SCL low and high time values */
- omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG, scll);
- omap_i2c_write_reg(dev, OMAP_I2C_SCLH_REG, sclh);
-
- /* Take the I2C module out of reset: */
- omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
-
/* Enable interrupts */
dev->iestate = (OMAP_I2C_IE_XRDY | OMAP_I2C_IE_RRDY |
OMAP_I2C_IE_NACK | OMAP_I2C_IE_AL) |
((dev->fifo_size) ? (OMAP_I2C_IE_RDR |
OMAP_I2C_IE_XDR) : 0);
- omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate);
- if (dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) {
- dev->pscstate = psc;
- dev->scllstate = scll;
- dev->sclhstate = sclh;
- dev->bufstate = buf;
- }
+
+ dev->pscstate = psc;
+ dev->scllstate = scll;
+ dev->sclhstate = sclh;
+
+ __omap_i2c_init(dev);
+
return 0;
}
@@ -1268,23 +1276,8 @@ static int omap_i2c_runtime_resume(struct device *dev)
{
struct omap_i2c_dev *_dev = dev_get_drvdata(dev);
- if (_dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) {
- omap_i2c_write_reg(_dev, OMAP_I2C_CON_REG, 0);
- omap_i2c_write_reg(_dev, OMAP_I2C_PSC_REG, _dev->pscstate);
- omap_i2c_write_reg(_dev, OMAP_I2C_SCLL_REG, _dev->scllstate);
- omap_i2c_write_reg(_dev, OMAP_I2C_SCLH_REG, _dev->sclhstate);
- omap_i2c_write_reg(_dev, OMAP_I2C_BUF_REG, _dev->bufstate);
- omap_i2c_write_reg(_dev, OMAP_I2C_SYSC_REG, _dev->syscstate);
- omap_i2c_write_reg(_dev, OMAP_I2C_WE_REG, _dev->westate);
- omap_i2c_write_reg(_dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
- }
-
- /*
- * Don't write to this register if the IE state is 0 as it can
- * cause deadlock.
- */
- if (_dev->iestate)
- omap_i2c_write_reg(_dev, OMAP_I2C_IE_REG, _dev->iestate);
+ if (_dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE)
+ __omap_i2c_init(_dev);
return 0;
}
--
1.7.5.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v2] i2c: omap: re-factor omap_i2c_init function
2012-10-25 6:36 ` Felipe Balbi
@ 2012-10-25 6:53 ` Shubhrajyoti Datta
2012-10-25 7:03 ` Felipe Balbi
2012-10-25 9:34 ` Shubhrajyoti Datta
1 sibling, 1 reply; 6+ messages in thread
From: Shubhrajyoti Datta @ 2012-10-25 6:53 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Oct 25, 2012 at 12:06 PM, Felipe Balbi <balbi@ti.com> wrote:
> Hi,
>
> On Thu, Oct 25, 2012 at 12:06:51PM +0530, Shubhrajyoti D wrote:
>> re-factor omap_i2c_init() so that we can re-use it for resume.
>> While at it also remove the bufstate variable as we write it
>> in omap_i2c_resize_fifo for every transfer.
>>
>> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
>> ---
>> v2 - add the iestate 0 check back.
>> - Remove a stray change.
>> - Applies on top of Felipe's patches.
>> http://www.spinics.net/lists/linux-omap/msg79995.html
>>
>>
>> Tested with Terro sys fix + Felipe's stop sched_clock() during suspend
>> on omap3636 beagle both idle and suspend.
>>
>> Functional testing on omap4sdp.
>>
>> drivers/i2c/busses/i2c-omap.c | 71 ++++++++++++++++++----------------------
>> 1 files changed, 32 insertions(+), 39 deletions(-)
>>
>> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
>> index 5e5cefb..3d400b1 100644
>> --- a/drivers/i2c/busses/i2c-omap.c
>> +++ b/drivers/i2c/busses/i2c-omap.c
>> @@ -209,7 +209,6 @@ struct omap_i2c_dev {
>> u16 pscstate;
>> u16 scllstate;
>> u16 sclhstate;
>> - u16 bufstate;
>> u16 syscstate;
>> u16 westate;
>> u16 errata;
>> @@ -285,9 +284,31 @@ static inline u16 omap_i2c_read_reg(struct omap_i2c_dev *i2c_dev, int reg)
>> }
>> }
>>
>> +static void __omap_i2c_init(struct omap_i2c_dev *dev)
>> +{
>> +
>> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
>> + /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */
>> + omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, dev->pscstate);
>> +
>> + /* SCL low and high time values */
>> + omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG, dev->scllstate);
>> + omap_i2c_write_reg(dev, OMAP_I2C_SCLH_REG, dev->sclhstate);
>> + if (dev->rev >= OMAP_I2C_REV_ON_3430_3530)
>> + omap_i2c_write_reg(dev, OMAP_I2C_WE_REG, dev->westate);
>> + /* Take the I2C module out of reset: */
>> + omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
>
> a few blank lines in this function wouldn't hurt and they would help
> with readability.
Will add .
>
>> + /*
>> + * Don't write to this register if the IE state is 0 as it can
>> + * cause deadlock.
>> + */
>> + if (dev->iestate)
>> + omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate);
>> +}
>> +
>> static int omap_i2c_init(struct omap_i2c_dev *dev)
>> {
>> - u16 psc = 0, scll = 0, sclh = 0, buf = 0;
>> + u16 psc = 0, scll = 0, sclh = 0;
>> u16 fsscll = 0, fssclh = 0, hsscll = 0, hssclh = 0;
>> unsigned long fclk_rate = 12000000;
>> unsigned long timeout;
>> @@ -337,11 +358,8 @@ static int omap_i2c_init(struct omap_i2c_dev *dev)
>> * REVISIT: Some wkup sources might not be needed.
>> */
>> dev->westate = OMAP_I2C_WE_ALL;
>> - omap_i2c_write_reg(dev, OMAP_I2C_WE_REG,
>> - dev->westate);
>
> remove the comment too since now that's done by some other function ?
>
>> }
>> }
>> - omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
>>
>> if (dev->flags & OMAP_I2C_FLAG_ALWAYS_ARMXOR_CLK) {
>> /*
>> @@ -426,28 +444,18 @@ static int omap_i2c_init(struct omap_i2c_dev *dev)
>> sclh = fclk_rate / (dev->speed * 2) - 7 + psc;
>> }
>>
>> - /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */
>> - omap_i2c_write_reg(dev, OMAP_I2C_PSC_REG, psc);
>> -
>> - /* SCL low and high time values */
>> - omap_i2c_write_reg(dev, OMAP_I2C_SCLL_REG, scll);
>> - omap_i2c_write_reg(dev, OMAP_I2C_SCLH_REG, sclh);
>> -
>> - /* Take the I2C module out of reset: */
>> - omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
>> -
>> /* Enable interrupts */
>> dev->iestate = (OMAP_I2C_IE_XRDY | OMAP_I2C_IE_RRDY |
>> OMAP_I2C_IE_NACK | OMAP_I2C_IE_AL) |
>> ((dev->fifo_size) ? (OMAP_I2C_IE_RDR |
>> OMAP_I2C_IE_XDR) : 0);
>> - omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate);
>> - if (dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) {
>> - dev->pscstate = psc;
>> - dev->scllstate = scll;
>> - dev->sclhstate = sclh;
>> - dev->bufstate = buf;
>> - }
>> +
>> + dev->pscstate = psc;
>> + dev->scllstate = scll;
>> + dev->sclhstate = sclh;
>> +
>> + __omap_i2c_init(dev);
>> +
>> return 0;
>> }
>>
>> @@ -1268,23 +1276,8 @@ static int omap_i2c_runtime_resume(struct device *dev)
>> {
>> struct omap_i2c_dev *_dev = dev_get_drvdata(dev);
>>
>> - if (_dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) {
>> - omap_i2c_write_reg(_dev, OMAP_I2C_CON_REG, 0);
>> - omap_i2c_write_reg(_dev, OMAP_I2C_PSC_REG, _dev->pscstate);
>> - omap_i2c_write_reg(_dev, OMAP_I2C_SCLL_REG, _dev->scllstate);
>> - omap_i2c_write_reg(_dev, OMAP_I2C_SCLH_REG, _dev->sclhstate);
>> - omap_i2c_write_reg(_dev, OMAP_I2C_BUF_REG, _dev->bufstate);
>> - omap_i2c_write_reg(_dev, OMAP_I2C_SYSC_REG, _dev->syscstate);
>> - omap_i2c_write_reg(_dev, OMAP_I2C_WE_REG, _dev->westate);
>> - omap_i2c_write_reg(_dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
>> - }
>> -
>> - /*
>> - * Don't write to this register if the IE state is 0 as it can
>> - * cause deadlock.
>> - */
>> - if (_dev->iestate)
>> - omap_i2c_write_reg(_dev, OMAP_I2C_IE_REG, _dev->iestate);
>> + if (_dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE)
>> + __omap_i2c_init(_dev);
>>
>> return 0;
>> }
>
> you continue to miss the changes in omap_i2c_xfer_msg() and your
> explanation of why not doing it wasn't good enough IMHO.
Will do that . I am preparing a seperate patch for moving the
calculation to a seperate function.
>
> --
> balbi
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v2] i2c: omap: re-factor omap_i2c_init function
2012-10-25 6:53 ` Shubhrajyoti Datta
@ 2012-10-25 7:03 ` Felipe Balbi
0 siblings, 0 replies; 6+ messages in thread
From: Felipe Balbi @ 2012-10-25 7:03 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Thu, Oct 25, 2012 at 12:23:56PM +0530, Shubhrajyoti Datta wrote:
> >> @@ -1268,23 +1276,8 @@ static int omap_i2c_runtime_resume(struct device *dev)
> >> {
> >> struct omap_i2c_dev *_dev = dev_get_drvdata(dev);
> >>
> >> - if (_dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE) {
> >> - omap_i2c_write_reg(_dev, OMAP_I2C_CON_REG, 0);
> >> - omap_i2c_write_reg(_dev, OMAP_I2C_PSC_REG, _dev->pscstate);
> >> - omap_i2c_write_reg(_dev, OMAP_I2C_SCLL_REG, _dev->scllstate);
> >> - omap_i2c_write_reg(_dev, OMAP_I2C_SCLH_REG, _dev->sclhstate);
> >> - omap_i2c_write_reg(_dev, OMAP_I2C_BUF_REG, _dev->bufstate);
> >> - omap_i2c_write_reg(_dev, OMAP_I2C_SYSC_REG, _dev->syscstate);
> >> - omap_i2c_write_reg(_dev, OMAP_I2C_WE_REG, _dev->westate);
> >> - omap_i2c_write_reg(_dev, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
> >> - }
> >> -
> >> - /*
> >> - * Don't write to this register if the IE state is 0 as it can
> >> - * cause deadlock.
> >> - */
> >> - if (_dev->iestate)
> >> - omap_i2c_write_reg(_dev, OMAP_I2C_IE_REG, _dev->iestate);
> >> + if (_dev->flags & OMAP_I2C_FLAG_RESET_REGS_POSTIDLE)
> >> + __omap_i2c_init(_dev);
> >>
> >> return 0;
> >> }
> >
> > you continue to miss the changes in omap_i2c_xfer_msg() and your
> > explanation of why not doing it wasn't good enough IMHO.
>
> Will do that . I am preparing a seperate patch for moving the
> calculation to a seperate function.
why do you need yet another function ? omap_i2c_init() does all
calculation and __omap_i2c_init() doesn't do any calculations. What's
the point for yet another function ?
--
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20121025/5b6583bd/attachment-0001.sig>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v2] i2c: omap: re-factor omap_i2c_init function
2012-10-25 6:36 ` Felipe Balbi
2012-10-25 6:53 ` Shubhrajyoti Datta
@ 2012-10-25 9:34 ` Shubhrajyoti Datta
2012-10-25 10:09 ` Felipe Balbi
1 sibling, 1 reply; 6+ messages in thread
From: Shubhrajyoti Datta @ 2012-10-25 9:34 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Oct 25, 2012 at 12:06 PM, Felipe Balbi <balbi@ti.com> wrote:
[...]
>> + * Don't write to this register if the IE state is 0 as it can
>> + * cause deadlock.
>> + */
>> + if (dev->iestate)
>> + omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate);
>> +}
>> +
>> static int omap_i2c_init(struct omap_i2c_dev *dev)
>> {
>> - u16 psc = 0, scll = 0, sclh = 0, buf = 0;
>> + u16 psc = 0, scll = 0, sclh = 0;
>> u16 fsscll = 0, fssclh = 0, hsscll = 0, hssclh = 0;
>> unsigned long fclk_rate = 12000000;
>> unsigned long timeout;
>> @@ -337,11 +358,8 @@ static int omap_i2c_init(struct omap_i2c_dev *dev)
>> * REVISIT: Some wkup sources might not be needed.
>> */
>> dev->westate = OMAP_I2C_WE_ALL;
>> - omap_i2c_write_reg(dev, OMAP_I2C_WE_REG,
>> - dev->westate);
>
> remove the comment too since now that's done by some other function ?
The comment is applicable to the OMAP_I2C_WE_ALL value.
So I thought it could be kept.
dont feel strongly though.
>
>> }
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v2] i2c: omap: re-factor omap_i2c_init function
2012-10-25 9:34 ` Shubhrajyoti Datta
@ 2012-10-25 10:09 ` Felipe Balbi
0 siblings, 0 replies; 6+ messages in thread
From: Felipe Balbi @ 2012-10-25 10:09 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Thu, Oct 25, 2012 at 03:04:29PM +0530, Shubhrajyoti Datta wrote:
> On Thu, Oct 25, 2012 at 12:06 PM, Felipe Balbi <balbi@ti.com> wrote:
>
> [...]
> >> + * Don't write to this register if the IE state is 0 as it can
> >> + * cause deadlock.
> >> + */
> >> + if (dev->iestate)
> >> + omap_i2c_write_reg(dev, OMAP_I2C_IE_REG, dev->iestate);
> >> +}
> >> +
> >> static int omap_i2c_init(struct omap_i2c_dev *dev)
> >> {
> >> - u16 psc = 0, scll = 0, sclh = 0, buf = 0;
> >> + u16 psc = 0, scll = 0, sclh = 0;
> >> u16 fsscll = 0, fssclh = 0, hsscll = 0, hssclh = 0;
> >> unsigned long fclk_rate = 12000000;
> >> unsigned long timeout;
> >> @@ -337,11 +358,8 @@ static int omap_i2c_init(struct omap_i2c_dev *dev)
> >> * REVISIT: Some wkup sources might not be needed.
> >> */
> >> dev->westate = OMAP_I2C_WE_ALL;
> >> - omap_i2c_write_reg(dev, OMAP_I2C_WE_REG,
> >> - dev->westate);
> >
> > remove the comment too since now that's done by some other function ?
>
> The comment is applicable to the OMAP_I2C_WE_ALL value.
> So I thought it could be kept.
>
> dont feel strongly though.
I see. that's ok then.
--
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20121025/9ddee6e4/attachment.sig>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2012-10-25 10:09 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-10-25 6:36 [PATCH v2] i2c: omap: re-factor omap_i2c_init function Shubhrajyoti D
2012-10-25 6:36 ` Felipe Balbi
2012-10-25 6:53 ` Shubhrajyoti Datta
2012-10-25 7:03 ` Felipe Balbi
2012-10-25 9:34 ` Shubhrajyoti Datta
2012-10-25 10:09 ` Felipe Balbi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).