[PATCH 1/2] ARM: mach-imx: imx53.dtsi: pinctl update

[PATCH 1/2] ARM: mach-imx: imx53.dtsi: pinctl update

[Roland Stigge]

This patch supplements pinctl support on i.MX53.

Signed-off-by: Roland Stigge <stigge@antcom.de>
---
 arch/arm/boot/dts/imx53.dtsi |   46 +++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 46 insertions(+)

--- linux-2.6.orig/arch/arm/boot/dts/imx53.dtsi
+++ linux-2.6/arch/arm/boot/dts/imx53.dtsi
@@ -316,6 +316,24 @@
 					};
 				};
 
+				can1 {
+					pinctrl_can1_1: can1grp-1 {
+						fsl,pins = <
+							847 0x80000000  /* MX53_PAD_PATA_INTRQ__CAN1_TXCAN */
+							853 0x80000000  /* MX53_PAD_PATA_DIOR__CAN1_RXCAN */
+						>;
+					};
+				};
+
+				can2 {
+					pinctrl_can2_1: can2grp-1 {
+						fsl,pins = <
+							67  0x80000000  /* MX53_PAD_KEY_COL4__CAN2_TXCAN */
+							74  0x80000000  /* MX53_PAD_KEY_ROW4__CAN2_RXCAN */
+						>;
+					};
+				};
+
 				i2c1 {
 					pinctrl_i2c1_1: i2c1grp-1 {
 						fsl,pins = <
@@ -334,6 +352,15 @@
 					};
 				};
 
+				i2c3 {
+					pinctrl_i2c3_1: i2c3grp-1 {
+						fsl,pins = <
+							1102 0xc0000000	/* MX53_PAD_GPIO_6__I2C3_SDA */
+							1130 0xc0000000	/* MX53_PAD_GPIO_5__I2C3_SCL */
+						>;
+					};
+				};
+
 				uart1 {
 					pinctrl_uart1_1: uart1grp-1 {
 						fsl,pins = <
@@ -369,6 +396,25 @@
 						>;
 					};
 				};
+
+				uart4 {
+					pinctrl_uart4_1: uart4grp-1 {
+						fsl,pins = <
+							11 0x1c5	/* MX53_PAD_KEY_COL0__UART4_TXD_MUX */
+							18 0x1c5	/* MX53_PAD_KEY_ROW0__UART4_RXD_MUX */
+						>;
+					};
+				};
+
+				uart5 {
+					pinctrl_uart5_1: uart5grp-1 {
+						fsl,pins = <
+							24 0x1c5	/* MX53_PAD_KEY_COL1__UART5_TXD_MUX */
+							31 0x1c5	/* MX53_PAD_KEY_ROW1__UART5_RXD_MUX */
+						>;
+					};
+				};
+
 			};
 
 			uart1: serial at 53fbc000 {

[PATCH 2/2] ARM: mach-imx: CAN clock fix for i.MX53

[Roland Stigge]

This patch fixes CAN clocking on i.MX53.

Signed-off-by: Roland Stigge <stigge@antcom.de>

---
 arch/arm/mach-imx/clk-imx51-imx53.c |    8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

--- linux-2.6.orig/arch/arm/mach-imx/clk-imx51-imx53.c
+++ linux-2.6/arch/arm/mach-imx/clk-imx51-imx53.c
@@ -426,10 +426,10 @@ int __init mx53_clocks_init(unsigned lon
 	clk[usb_phy2_gate] = imx_clk_gate2("usb_phy2_gate", "usb_phy_sel", MXC_CCM_CCGR4, 12);
 	clk[can_sel] = imx_clk_mux("can_sel", MXC_CCM_CSCMR2, 6, 2,
 				mx53_can_sel, ARRAY_SIZE(mx53_can_sel));
-	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR6, 22);
-	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR6, 20);
-	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 8);
-	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 6);
+	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR4, 6);
+	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
+	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 6);
+	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
 	clk[i2c3_gate] = imx_clk_gate2("i2c3_gate", "per_root", MXC_CCM_CCGR1, 22);
 
 	for (i = 0; i < ARRAY_SIZE(clk); i++)

[PATCH 2/2] ARM: mach-imx: CAN clock fix for i.MX53

[Sascha Hauer]

On Thu, Oct 25, 2012 at 01:26:40PM +0200, Roland Stigge wrote:
> This patch fixes CAN clocking on i.MX53.
> 
> Signed-off-by: Roland Stigge <stigge@antcom.de>
> 
> ---
>  arch/arm/mach-imx/clk-imx51-imx53.c |    8 ++++----
>  1 file changed, 4 insertions(+), 4 deletions(-)
> 
> --- linux-2.6.orig/arch/arm/mach-imx/clk-imx51-imx53.c
> +++ linux-2.6/arch/arm/mach-imx/clk-imx51-imx53.c
> @@ -426,10 +426,10 @@ int __init mx53_clocks_init(unsigned lon
>  	clk[usb_phy2_gate] = imx_clk_gate2("usb_phy2_gate", "usb_phy_sel", MXC_CCM_CCGR4, 12);
>  	clk[can_sel] = imx_clk_mux("can_sel", MXC_CCM_CSCMR2, 6, 2,
>  				mx53_can_sel, ARRAY_SIZE(mx53_can_sel));
> -	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR6, 22);
> -	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR6, 20);
> -	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 8);
> -	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 6);

I just rechecked. The above matches the i.MX53 Reference Manual rev 2.1

> +	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR4, 6);
> +	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
> +	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 6);
> +	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);

This doesn't.

Can you elaborate why you think this is necessary?

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

[PATCH 2/2] ARM: mach-imx: CAN clock fix for i.MX53

[Roland Stigge]

Hi!

On 10/26/2012 10:59 AM, Sascha Hauer wrote:
> On Thu, Oct 25, 2012 at 01:26:40PM +0200, Roland Stigge wrote:
>> This patch fixes CAN clocking on i.MX53.
>>
>> Signed-off-by: Roland Stigge <stigge@antcom.de>
>>
>> ---
>>  arch/arm/mach-imx/clk-imx51-imx53.c |    8 ++++----
>>  1 file changed, 4 insertions(+), 4 deletions(-)
>>
>> --- linux-2.6.orig/arch/arm/mach-imx/clk-imx51-imx53.c
>> +++ linux-2.6/arch/arm/mach-imx/clk-imx51-imx53.c
>> @@ -426,10 +426,10 @@ int __init mx53_clocks_init(unsigned lon
>>  	clk[usb_phy2_gate] = imx_clk_gate2("usb_phy2_gate", "usb_phy_sel", MXC_CCM_CCGR4, 12);
>>  	clk[can_sel] = imx_clk_mux("can_sel", MXC_CCM_CSCMR2, 6, 2,
>>  				mx53_can_sel, ARRAY_SIZE(mx53_can_sel));
>> -	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR6, 22);
>> -	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR6, 20);
>> -	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 8);
>> -	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 6);
> 
> I just rechecked. The above matches the i.MX53 Reference Manual rev 2.1
> 
>> +	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR4, 6);
>> +	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
>> +	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 6);
>> +	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
> 
> This doesn't.

This may be right, but unfortunately, since the introduction of your
can1 + can2 clocking change, the first block stopped working for me.

My above patch is basically a rollback which works for the first block.

An interesting hint is: can2 (which was the only one defined _before_
your can1 + can2 change) didn't work before and afterwards at all. (But
I'm not using it anyway.)

Thanks,

Roland

[PATCH 2/2] ARM: mach-imx: CAN clock fix for i.MX53

[Marc Kleine-Budde]

On 10/26/2012 11:16 AM, Roland Stigge wrote:
> Hi!
> 
> On 10/26/2012 10:59 AM, Sascha Hauer wrote:
>> On Thu, Oct 25, 2012 at 01:26:40PM +0200, Roland Stigge wrote:
>>> This patch fixes CAN clocking on i.MX53.
>>>
>>> Signed-off-by: Roland Stigge <stigge@antcom.de>
>>>
>>> ---
>>>  arch/arm/mach-imx/clk-imx51-imx53.c |    8 ++++----
>>>  1 file changed, 4 insertions(+), 4 deletions(-)
>>>
>>> --- linux-2.6.orig/arch/arm/mach-imx/clk-imx51-imx53.c
>>> +++ linux-2.6/arch/arm/mach-imx/clk-imx51-imx53.c
>>> @@ -426,10 +426,10 @@ int __init mx53_clocks_init(unsigned lon
>>>  	clk[usb_phy2_gate] = imx_clk_gate2("usb_phy2_gate", "usb_phy_sel", MXC_CCM_CCGR4, 12);
>>>  	clk[can_sel] = imx_clk_mux("can_sel", MXC_CCM_CSCMR2, 6, 2,
>>>  				mx53_can_sel, ARRAY_SIZE(mx53_can_sel));
>>> -	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR6, 22);
>>> -	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR6, 20);
>>> -	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 8);
>>> -	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 6);
>>
>> I just rechecked. The above matches the i.MX53 Reference Manual rev 2.1

An old rev 1 manual has lists the same bits.

>>> +	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR4, 6);
>>> +	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
>>> +	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 6);
>>> +	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
>>
>> This doesn't.
> 
> This may be right, but unfortunately, since the introduction of your
> can1 + can2 clocking change, the first block stopped working for me.

You are effectively using can2's clock for can1. Are you sure you
haven't mixed up can1 and can2?

> My above patch is basically a rollback which works for the first block.
> 
> An interesting hint is: can2 (which was the only one defined _before_
> your can1 + can2 change) didn't work before and afterwards at all. (But
> I'm not using it anyway.)

Marc

-- 
Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 259 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20121026/f9790b6b/attachment-0001.sig>

[PATCH 2/2] ARM: mach-imx: CAN clock fix for i.MX53

[Roland Stigge]

On 10/26/2012 12:30 PM, Marc Kleine-Budde wrote:
>>>> +	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate",
>>>> "can_sel", MXC_CCM_CCGR4, 6); +	clk[can1_ipg_gate] =
>>>> imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR4, 8); +
>>>> clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate",
>>>> "can_sel", MXC_CCM_CCGR4, 6); +	clk[can2_ipg_gate] =
>>>> imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
>>> 
>>> This doesn't.
>> 
>> This may be right, but unfortunately, since the introduction of
>> your can1 + can2 clocking change, the first block stopped working
>> for me.
> 
> You are effectively using can2's clock for can1. Are you sure you 
> haven't mixed up can1 and can2?

Just using the above patch and patch 1/2 from this series (missing can
pinmuxing), doing like this in custom .dts:

+                       can1: can at 53fc8000 {
+                               pinctrl-names = "default";
+                               pinctrl-0 = <&pinctrl_can1_1>;
+                               clock-frequency = <66500000>;
+                               status = "okay";
+                       };

Then, the can0 interface appears which can be upped as network interface.

Quite straightforward, isn't it?

Roland

[PATCH 2/2] ARM: mach-imx: CAN clock fix for i.MX53

[Roland Stigge]

On 10/26/2012 01:05 PM, Roland Stigge wrote:
> On 10/26/2012 12:30 PM, Marc Kleine-Budde wrote:
>>>>> +	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate",
>>>>> "can_sel", MXC_CCM_CCGR4, 6); +	clk[can1_ipg_gate] =
>>>>> imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR4, 8); +
>>>>> clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate",
>>>>> "can_sel", MXC_CCM_CCGR4, 6); +	clk[can2_ipg_gate] =
>>>>> imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
>>>>
>>>> This doesn't.
>>>
>>> This may be right, but unfortunately, since the introduction of
>>> your can1 + can2 clocking change, the first block stopped working
>>> for me.
>>
>> You are effectively using can2's clock for can1. Are you sure you 
>> haven't mixed up can1 and can2?
> 
> Just using the above patch and patch 1/2 from this series (missing can
> pinmuxing), doing like this in custom .dts:
> 
> +                       can1: can at 53fc8000 {
> +                               pinctrl-names = "default";
> +                               pinctrl-0 = <&pinctrl_can1_1>;
> +                               clock-frequency = <66500000>;

That was the problem, since in flexcan.c probe():


	if (pdev->dev.of_node)
		of_property_read_u32(pdev->dev.of_node,
						"clock-frequency", &clock_freq);

	if (!clock_freq) {
		clk_ipg = devm_clk_get(&pdev->dev, "ipg");
		if (IS_ERR(clk_ipg)) {
			dev_err(&pdev->dev, "no ipg clock defined\n");
			err = PTR_ERR(clk_ipg);
			goto failed_clock;
		}
		clock_freq = clk_get_rate(clk_ipg);

		clk_per = devm_clk_get(&pdev->dev, "per");
		if (IS_ERR(clk_per)) {
			dev_err(&pdev->dev, "no per clock defined\n");
			err = PTR_ERR(clk_per);
			goto failed_clock;
		}
	}

Sorry for the noise.

The other patches are still current.

Thanks,

Roland

[PATCH 2/2] ARM: mach-imx: CAN clock fix for i.MX53

[Marc Kleine-Budde]

On 10/26/2012 03:52 PM, Roland Stigge wrote:
> On 10/26/2012 01:05 PM, Roland Stigge wrote:
>> On 10/26/2012 12:30 PM, Marc Kleine-Budde wrote:
>>>>>> +	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate",
>>>>>> "can_sel", MXC_CCM_CCGR4, 6); +	clk[can1_ipg_gate] =
>>>>>> imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR4, 8); +
>>>>>> clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate",
>>>>>> "can_sel", MXC_CCM_CCGR4, 6); +	clk[can2_ipg_gate] =
>>>>>> imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
>>>>>
>>>>> This doesn't.
>>>>
>>>> This may be right, but unfortunately, since the introduction of
>>>> your can1 + can2 clocking change, the first block stopped working
>>>> for me.
>>>
>>> You are effectively using can2's clock for can1. Are you sure you 
>>> haven't mixed up can1 and can2?
>>
>> Just using the above patch and patch 1/2 from this series (missing can
>> pinmuxing), doing like this in custom .dts:
>>
>> +                       can1: can at 53fc8000 {
>> +                               pinctrl-names = "default";
>> +                               pinctrl-0 = <&pinctrl_can1_1>;
>> +                               clock-frequency = <66500000>;
> 
> That was the problem, since in flexcan.c probe():
> 
> 
> 	if (pdev->dev.of_node)
> 		of_property_read_u32(pdev->dev.of_node,
> 						"clock-frequency", &clock_freq);
> 
> 	if (!clock_freq) {
> 		clk_ipg = devm_clk_get(&pdev->dev, "ipg");
> 		if (IS_ERR(clk_ipg)) {
> 			dev_err(&pdev->dev, "no ipg clock defined\n");
> 			err = PTR_ERR(clk_ipg);
> 			goto failed_clock;
> 		}
> 		clock_freq = clk_get_rate(clk_ipg);
> 
> 		clk_per = devm_clk_get(&pdev->dev, "per");
> 		if (IS_ERR(clk_per)) {
> 			dev_err(&pdev->dev, "no per clock defined\n");
> 			err = PTR_ERR(clk_per);
> 			goto failed_clock;
> 		}
> 	}
> 
> Sorry for the noise.

We have the possibility to specify the clock frequency in the device
tree as the power pc has no support for generic clock yet.

Marc
-- 
Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 259 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20121026/641db69d/attachment.sig>

[PATCH 2/2] ARM: mach-imx: CAN clock fix for i.MX53

[Sascha Hauer]

Roland,

Do you have updates on this one? I think this patch is wrong, specifying
the clock rate in the devicetree is only for PowerPC, so I think this
needs further investigation.

Sascha

On Thu, Oct 25, 2012 at 01:26:40PM +0200, Roland Stigge wrote:
> This patch fixes CAN clocking on i.MX53.
> 
> Signed-off-by: Roland Stigge <stigge@antcom.de>
> 
> ---
>  arch/arm/mach-imx/clk-imx51-imx53.c |    8 ++++----
>  1 file changed, 4 insertions(+), 4 deletions(-)
> 
> --- linux-2.6.orig/arch/arm/mach-imx/clk-imx51-imx53.c
> +++ linux-2.6/arch/arm/mach-imx/clk-imx51-imx53.c
> @@ -426,10 +426,10 @@ int __init mx53_clocks_init(unsigned lon
>  	clk[usb_phy2_gate] = imx_clk_gate2("usb_phy2_gate", "usb_phy_sel", MXC_CCM_CCGR4, 12);
>  	clk[can_sel] = imx_clk_mux("can_sel", MXC_CCM_CSCMR2, 6, 2,
>  				mx53_can_sel, ARRAY_SIZE(mx53_can_sel));
> -	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR6, 22);
> -	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR6, 20);
> -	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 8);
> -	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 6);
> +	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR4, 6);
> +	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
> +	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 6);
> +	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
>  	clk[i2c3_gate] = imx_clk_gate2("i2c3_gate", "per_root", MXC_CCM_CCGR1, 22);
>  
>  	for (i = 0; i < ARRAY_SIZE(clk); i++)
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

[PATCH 2/2] ARM: mach-imx: CAN clock fix for i.MX53

[Roland Stigge]

On 29/10/12 22:20, Sascha Hauer wrote:
> Roland,
> 
> Do you have updates on this one? I think this patch is wrong, specifying
> the clock rate in the devicetree is only for PowerPC, so I think this
> needs further investigation.

Please ignore it for now. As discussed with Marc, the issue seemed to be
caused by me (wrongfully) using the "clock-frequency" dt property which
caused probe() to ignore the clocks.

A colleague of mine will notify me if the problem surfaces again. So for
now I assume it's gone.

Maybe the above strategy regarding "clock-frequency" needs to be
documented better or changed, though, to prevent more confusion like in
the above case.

Thanks,

Roland

> On Thu, Oct 25, 2012 at 01:26:40PM +0200, Roland Stigge wrote:
>> This patch fixes CAN clocking on i.MX53.
>>
>> Signed-off-by: Roland Stigge <stigge@antcom.de>
>>
>> ---
>>  arch/arm/mach-imx/clk-imx51-imx53.c |    8 ++++----
>>  1 file changed, 4 insertions(+), 4 deletions(-)
>>
>> --- linux-2.6.orig/arch/arm/mach-imx/clk-imx51-imx53.c
>> +++ linux-2.6/arch/arm/mach-imx/clk-imx51-imx53.c
>> @@ -426,10 +426,10 @@ int __init mx53_clocks_init(unsigned lon
>>  	clk[usb_phy2_gate] = imx_clk_gate2("usb_phy2_gate", "usb_phy_sel", MXC_CCM_CCGR4, 12);
>>  	clk[can_sel] = imx_clk_mux("can_sel", MXC_CCM_CSCMR2, 6, 2,
>>  				mx53_can_sel, ARRAY_SIZE(mx53_can_sel));
>> -	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR6, 22);
>> -	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR6, 20);
>> -	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 8);
>> -	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 6);
>> +	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR4, 6);
>> +	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
>> +	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 6);
>> +	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
>>  	clk[i2c3_gate] = imx_clk_gate2("i2c3_gate", "per_root", MXC_CCM_CCGR1, 22);
>>  
>>  	for (i = 0; i < ARRAY_SIZE(clk); i++)
>>
> 

[PATCH 1/2] ARM: mach-imx: imx53.dtsi: pinctl update

[Sascha Hauer]

On Thu, Oct 25, 2012 at 01:26:39PM +0200, Roland Stigge wrote:
> This patch supplements pinctl support on i.MX53.
> 
> Signed-off-by: Roland Stigge <stigge@antcom.de>

Acked-by: Sascha Hauer <s.hauer@pengutronix.de>

Shawn, probably better when you take this patch as it's quite likely
that you collect other patches to this file.

Sascha

> ---
>  arch/arm/boot/dts/imx53.dtsi |   46 +++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 46 insertions(+)
> 
> --- linux-2.6.orig/arch/arm/boot/dts/imx53.dtsi
> +++ linux-2.6/arch/arm/boot/dts/imx53.dtsi
> @@ -316,6 +316,24 @@
>  					};
>  				};
>  
> +				can1 {
> +					pinctrl_can1_1: can1grp-1 {
> +						fsl,pins = <
> +							847 0x80000000  /* MX53_PAD_PATA_INTRQ__CAN1_TXCAN */
> +							853 0x80000000  /* MX53_PAD_PATA_DIOR__CAN1_RXCAN */
> +						>;
> +					};
> +				};
> +
> +				can2 {
> +					pinctrl_can2_1: can2grp-1 {
> +						fsl,pins = <
> +							67  0x80000000  /* MX53_PAD_KEY_COL4__CAN2_TXCAN */
> +							74  0x80000000  /* MX53_PAD_KEY_ROW4__CAN2_RXCAN */
> +						>;
> +					};
> +				};
> +
>  				i2c1 {
>  					pinctrl_i2c1_1: i2c1grp-1 {
>  						fsl,pins = <
> @@ -334,6 +352,15 @@
>  					};
>  				};
>  
> +				i2c3 {
> +					pinctrl_i2c3_1: i2c3grp-1 {
> +						fsl,pins = <
> +							1102 0xc0000000	/* MX53_PAD_GPIO_6__I2C3_SDA */
> +							1130 0xc0000000	/* MX53_PAD_GPIO_5__I2C3_SCL */
> +						>;
> +					};
> +				};
> +
>  				uart1 {
>  					pinctrl_uart1_1: uart1grp-1 {
>  						fsl,pins = <
> @@ -369,6 +396,25 @@
>  						>;
>  					};
>  				};
> +
> +				uart4 {
> +					pinctrl_uart4_1: uart4grp-1 {
> +						fsl,pins = <
> +							11 0x1c5	/* MX53_PAD_KEY_COL0__UART4_TXD_MUX */
> +							18 0x1c5	/* MX53_PAD_KEY_ROW0__UART4_RXD_MUX */
> +						>;
> +					};
> +				};
> +
> +				uart5 {
> +					pinctrl_uart5_1: uart5grp-1 {
> +						fsl,pins = <
> +							24 0x1c5	/* MX53_PAD_KEY_COL1__UART5_TXD_MUX */
> +							31 0x1c5	/* MX53_PAD_KEY_ROW1__UART5_RXD_MUX */
> +						>;
> +					};
> +				};
> +
>  			};
>  
>  			uart1: serial at 53fbc000 {
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

[PATCH 1/2] ARM: mach-imx: imx53.dtsi: pinctl update

[Shawn Guo]

On Mon, Oct 29, 2012 at 10:13:59PM +0100, Sascha Hauer wrote:
> On Thu, Oct 25, 2012 at 01:26:39PM +0200, Roland Stigge wrote:
> > This patch supplements pinctl support on i.MX53.
> > 
> > Signed-off-by: Roland Stigge <stigge@antcom.de>
> 
> Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
> 
> Shawn, probably better when you take this patch as it's quite likely
> that you collect other patches to this file.
> 
Applied with patch subject changed to

  ARM: dts: imx53: pinctl update

Shawn