From mboxrd@z Thu Jan  1 00:00:00 1970
From: andrew@lunn.ch (Andrew Lunn)
Date: Wed, 27 Feb 2013 08:03:33 +0100
Subject: [PATCH 1/4] arm: mvebu: limit OpenBlocks AX3-4 to 1 GB of RAM
In-Reply-To: <20130226162023.3d7b2ffc@skate>
References: <20130104183139.20492204@skate> <50E71356.3030203@lunn.ch>
 <20130104190345.460151d1@skate>
 <50E9EE7A.1080301@free-electrons.com>
 <20130106235312.0839a879@skate> <20130107094747.GR3392@lunn.ch>
 <20130107110712.GT3392@lunn.ch> <20130107122613.64f4ace5@skate>
 <20130107113411.GV3392@lunn.ch> <20130226162023.3d7b2ffc@skate>
Message-ID: <20130227070333.GK17242@lunn.ch>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

On Tue, Feb 26, 2013 at 04:20:23PM +0100, Thomas Petazzoni wrote:
> Dear Andrew Lunn,
> 
> On Mon, 7 Jan 2013 12:34:11 +0100, Andrew Lunn wrote:
> > > Image is also with an initramfs + appended DTB. My boot command is:
> > > 
> > > tftp 1000000 192.168.0.14:uImage.armada-xp-openblocks-ax3-4; bootm
> > > 
> > > So I'm loading to a different address than you.
> > 
> > Hi Thomas
> > 
> > Uboot tells me:
> > 
> > DRAM:   3 GB
> >        CS 0: base 0x00000000 size  1 GB
> >        CS 2: base 0x40000000 size  1 GB
> >        CS 3: base 0x80000000 size  1 GB
> >        Addresses 14M - 0M are saved for the U-Boot usage.
> > 
> > 1000000 would be towards the beginning of this area reserved for uboot.
> > 
> > Could you try moving to somewhere outside of the first 14Mbytes and
> > see if that helps.
> 
> Jumping back on this old topic of the OpenBlocks AX3 not being stable
> with 3 GB of RAM for Gr??gory and me, but being stable for you. Could
> you check which revision of the Armada XP you have? Is it A0 or B0?
> 
> I.e, check the message:
> 
>  SoC:   MV78460 B0
> 
> in U-Boot. Gr??gory and I are using OpenBlocks AX3 based on the A0
> version of the silicon (so the message I copy/pasted above is *not*
> from our OpenBlocks, but a different Armada XP board). However,
> PlatHome has been shipping since some time B0 revisions. Maybe it could
> explain the difference we're seeing?

Hi Thomas

My machine is an A0.

U-Boot 2009.08 (Jul 27 2012 - 18:23:11)
Plat'Home version: 1.1.1 (Base: Marvell BSP  2.2.3 NQ)

U-Boot Addressing:
       Code:            00600000:006BFFF0
       BSS:             0070D6A0
       Stack:           0x5fff70
       PageTable:       0x8e0000
       Heap address:    0x900000:0xe00000
Board: OpenBlocks AX3
SoC:   MV78260 A0
       running 2 CPUs
       Custom configuration
CPU:   Marvell PJ4B (584) v7 (Rev 2) LE
       CPU # 0
       CPU @ 1333Mhz, L2 @ 667Mhz
       DDR @ 667Mhz, TClock @ 250Mhz
       DDR 64Bit Width, FastPath Memory Access
       DDR ECC Disabled
PEX 0.0(0): Detected No Link.
PEX 0.1(1): Detected No Link.
DRAM:   3 GB
       CS 0: base 0x00000000 size  1 GB
       CS 2: base 0x40000000 size  1 GB
       CS 3: base 0x80000000 size  1 GB
       Addresses 14M - 0M are saved for the U-Boot usage.
Flash: 128 MB
POST:  mac verify Eth0 PASSED Eth1 PASSED Eth2 PASSED Eth3 PASSED 
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Device Mode
Power Off External Interface
Modules Detected:
MMC:   MRVL_MMC: 0
Net:   egiga0, egiga1, egiga2, egiga3

I know you recently found some issue with windows. Could that explain
something?

       Andrew