[PATCH 11/15] ARM: OMAP5: PM: Add L2 memory power down support

[nm@ti.com (Nishanth Menon)]

On 17:41-20130301, Santosh Shilimkar wrote:
> When the entire MPUSS cluster is powered down in device off state, L2 cache
> memory looses it's content and hence while targetting such a state,
> l2 cache needs to be flushed to main memory.
> 
> Add the necessary low power code support for the same.
> 
> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
> ---
>  arch/arm/mach-omap2/omap-secure.h     |    1 +
>  arch/arm/mach-omap2/sleep_omap4plus.S |   30 ++++++++++++++++++++++++++++++
>  2 files changed, 31 insertions(+)
> 
> diff --git a/arch/arm/mach-omap2/omap-secure.h b/arch/arm/mach-omap2/omap-secure.h
> index 1739468..a171a5a 100644
> --- a/arch/arm/mach-omap2/omap-secure.h
> +++ b/arch/arm/mach-omap2/omap-secure.h
> @@ -47,6 +47,7 @@
>  #define OMAP4_MON_L2X0_PREFETCH_INDEX	0x113
>  #define OMAP5_MON_CACHES_CLEAN_INDEX	0x103
>  #define OMAP5_MON_AUX_CTRL_INDEX	0x107
> +#define OMAP5_MON_L2AUX_CTRL_INDEX	0x104
>  
>  #define OMAP5_MON_AMBA_IF_INDEX		0x108
>  
> diff --git a/arch/arm/mach-omap2/sleep_omap4plus.S b/arch/arm/mach-omap2/sleep_omap4plus.S
> index f4874e5..ea318be 100644
> --- a/arch/arm/mach-omap2/sleep_omap4plus.S
> +++ b/arch/arm/mach-omap2/sleep_omap4plus.S
> @@ -386,6 +386,27 @@ skip_secure_l1_clean_op:
>  	isb
>  	dsb
>  
> +	bl	omap4_get_sar_ram_base
> +	mov	r8, r0
> +	mrc	p15, 0, r5, c0, c0, 5		@ Read MPIDR
> +	ands	r5, r5, #0x0f
> +	ldreq	r0, [r8, #L2X0_SAVE_OFFSET0]	@ Retrieve L2 state
> +	ldrne	r0, [r8, #L2X0_SAVE_OFFSET1]
> +	cmp	r0, #3
umm, we store l2x0_pwrst_prepare(cpu, save_state);
which in turn stores into L2X0_SAVE_OFFSET - I am with you so far
save_state in omap4_enter_lowpower is:
PWRDM_POWER_INACTIVE: 0
PWRDM_POWER_OFF: 1
or 2 in the case of OSWR
what is 3? ref:
https://github.com/SantoshShilimkar/linux/blob/testing/3.10/omap5-int-rebuild/arch/arm/mach-omap2/omap-mpuss-lowpower.c#L298
> +	bne	do_wfi
> +	bl	omap4_get_sar_ram_base
> +	ldr	r9, [r0, #OMAP_TYPE_OFFSET]
> +	cmp	r9, #0x1			@ Check for HS device
my 2c:
off topic: somewhere down the line, I think we need to clear up these
into macros so that as in this case, omap4_mpuss_init populated value
should be the same as here with usage of same macro without reviewer
needing to track down where it was set with what.

> +	bne	skip_secure_l2_clean_op
> +	mov	r0, #1				@ Clean secure L2
> +	stmfd   r13!, {r4-r12, r14}
> +	ldr	r12, =OMAP5_MON_CACHES_CLEAN_INDEX
> +	DO_SMC
> +	ldmfd   r13!, {r4-r12, r14}
> +skip_secure_l2_clean_op:
> +	mov	r0, #2				@ Flush L2
v7_flush_dcache_all does not take parameters, right?
> +	bl	v7_flush_dcache_all
> +
>  do_wfi:
>  	bl	omap_do_wfi
>  
> @@ -427,6 +448,15 @@ ENTRY(omap5_cpu_resume)
>  	dsb
>  1:
>  #endif
> +	mrc	p15, 1, r0, c15, c0, 0		@ Read L2 ACTLR
> +	cmp	r0, #0x118			@ Check if it is already set

> 	beq	skip_sec_l2
> +	ldr	r0, =0x118			@ Setup L2 ACTLR = 0x118
> +	ldr	r12, =OMAP5_MON_L2AUX_CTRL_INDEX
I hope I am looking at the right place:
http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0438g/BABIAICD.html
bit 3: Disable clean/evict push to external
bit 4: Disable WriteUnique and WriteLineUnique transactions from master
bit 8: Disable DVM/CMO message broadcast

Is'nt it better to configure on boot, save it into SAR memory and restore it
from SAR using monitor call? I mean it is possible that we start boot
with L2 ACTLR != 0x118 and then hit off and come out of OFF mode with
0x118.
One generally wants the system to be same before and after OFF/LP mode.
else, one tends to track bug such as
"At boot I see this bug, but after a while I dont see (cpuidle kicked in)"
- harder one to track down
or
"At boot I see this bug, but after a first suspend resume, I dont see (OFF kicked in)"
- easier one to track.
or vice versa and other combinations.. :(

> +	dsb
> +	smc     #0
DO_SMC ?
> +	dsb
> +skip_sec_l2:
>  	b	cpu_resume			@ Jump to generic resume

-- 
Regards,
Nishanth Menon