From: lee.jones@linaro.org (Lee Jones)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: ux500: Supply a DTS file for the u8540 platform
Date: Wed, 24 Apr 2013 08:52:12 +0100 [thread overview]
Message-ID: <20130424075212.GE17416@gmail.com> (raw)
In-Reply-To: <CACRpkdZWuw9O3-wr=g1AehZqmBR1YJ353w9ANfBTHhr5mRiwiw@mail.gmail.com>
On Tue, 23 Apr 2013, Linus Walleij wrote:
> On Thu, Apr 4, 2013 at 9:29 AM, Lee Jones <lee.jones@linaro.org> wrote:
>
> > This is a skeleton DTS file which only enables serial. Just using
> > this simple file yields a terminal when booting u8540.
> >
> > Signed-off-by: Lee Jones <lee.jones@linaro.org>
>
> Now, wait... this doesn't work.
This is very strange and not what I see in my branch.
> > +/ {
> > + model = "ST-Ericsson U8540 platform with Device Tree";
> > + compatible = "st-ericsson,u8540";
> > +
> > + memory {
> > + reg = <0x00000000 0x20000000>;
> > + };
>
> Funny whitespace. Use tabs ...
This a single tab in my branch/editor.
> > + soc-u9500 {
>
> Please rename this not just "soc"
Done.
> > + uart at 80120000 {
> > + status = "okay";
> > + };
> > +
> > + uart at 80121000 {
> > + status = "okay";
> > + };
> > +
> > + uart at 80007000 {
> > + status = "okay";
> > + };
> > + };
> > +};
>
> The whitespace looks a bit funny compared to the
> old patch, what happened here?
>
> It also has the side effect that patch 5/9 does not
> apply... By the way, since I already applied 4/9, please
> squash 5/9 into this patch to avoid problems.
It's quite common for issues to occur when patches are taken
out-of-order. As I work with topic branches, my preference would
normally be to fix issues with the patch-set as a whole until Acks are
obtained for all of the patches, then either send a pull-request or to
have all of the patches taken from the MLs in order.
> Finally, please patch arch/arm/boot/dts/Makefile
> in the obvious way so that the DTB gets compiled.
Ah yes. Good spot.
--
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
next prev parent reply other threads:[~2013-04-24 7:52 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-04-02 13:21 [PATCH 1/9] ARM: ux500: Increase the size of the PRCMU's TCPM size Lee Jones
2013-04-02 13:21 ` [PATCH 2/9] ARM: ux500: Remove incorrect DB9540 PRCMU TCDM base location Lee Jones
2013-04-03 20:33 ` Linus Walleij
2013-04-02 13:21 ` [PATCH 3/9] ARM: ux500: Supply a DTS file for the u8540 platform Lee Jones
2013-04-03 20:34 ` Linus Walleij
2013-04-04 7:29 ` [PATCH] " Lee Jones
2013-04-23 10:42 ` Linus Walleij
2013-04-23 10:58 ` Linus Walleij
2013-04-24 7:52 ` Lee Jones [this message]
2013-04-02 13:21 ` [PATCH 4/9] ARM: ux500: Move Snowball's thermal DT node into existing PRCMU one Lee Jones
2013-04-03 20:38 ` Linus Walleij
2013-04-03 21:36 ` Linus Walleij
2013-04-03 21:45 ` Linus Walleij
2013-04-04 7:20 ` Lee Jones
2013-04-02 13:21 ` [PATCH 5/9] ARM: ux500: Over-ride TCDM size when booting the DB8540 platform Lee Jones
2013-04-03 20:39 ` Linus Walleij
2013-04-04 7:33 ` [PATCH] " Lee Jones
2013-04-23 10:59 ` Linus Walleij
2013-04-23 15:09 ` Lee Jones
2013-04-02 13:21 ` [PATCH 6/9] ARM: ux500: Create a new of_dev_auxdata structure for u8540 enablement Lee Jones
2013-04-03 20:42 ` Linus Walleij
2013-04-02 13:21 ` [PATCH 7/9] ARM: ux500: Add a VQMMC (level-shifting) regulator DT node for Snowball Lee Jones
2013-04-03 20:44 ` Linus Walleij
2013-04-02 13:21 ` [PATCH 8/9] mfd: db8500-prcmu: Return early if the TCPM cannot be located Lee Jones
2013-04-03 20:46 ` Linus Walleij
2013-04-02 13:21 ` [PATCH 9/9] mfd: db8500-prcmu: Support platform dependant device selection Lee Jones
2013-04-03 20:47 ` Linus Walleij
2013-04-04 10:15 ` Lee Jones
2013-04-03 20:32 ` [PATCH 1/9] ARM: ux500: Increase the size of the PRCMU's TCPM size Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20130424075212.GE17416@gmail.com \
--to=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).