From: s.hauer@pengutronix.de (Sascha Hauer)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2] ARM: dts: Add SPI support for i.MX27 Phytec PCM038 module
Date: Fri, 3 May 2013 19:04:34 +0200 [thread overview]
Message-ID: <20130503170434.GV32299@pengutronix.de> (raw)
In-Reply-To: <1367568501-29467-1-git-send-email-shc_work@mail.ru>
On Fri, May 03, 2013 at 12:08:21PM +0400, Alexander Shiyan wrote:
> Added SPI node and PMIC MC13783 (spi0.0) to imx27-phytec-phycore DT file.
>
> Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
> ---
> arch/arm/boot/dts/imx27-phytec-phycore.dts | 109 +++++++++++++++++++++++++++++
> 1 file changed, 109 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx27-phytec-phycore.dts b/arch/arm/boot/dts/imx27-phytec-phycore.dts
> index fe64e3a..eb7d9fa 100644
> --- a/arch/arm/boot/dts/imx27-phytec-phycore.dts
> +++ b/arch/arm/boot/dts/imx27-phytec-phycore.dts
> @@ -72,6 +72,115 @@
> };
> };
>
> +&cspi1 {
> + fsl,spi-num-chipselects = <1>;
> + cs-gpios = <&gpio4 28 0>;
> + status = "okay";
> +
> + pmic: mc13783 at 0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,mc13783";
> + spi-max-frequency = <20000000>;
> + reg = <0>;
> + interrupt-parent = <&gpio2>;
> + interrupts = <23 0x4>;
> + fsl,mc13xxx-uses-adc;
> + fsl,mc13xxx-uses-rtc;
> +
> + regulators {
> + sw1a_reg: sw1a {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + sw1b_reg: sw1b {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + sw2a_reg: sw2a {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + sw2b_reg: sw2b {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + sw3_reg: sw3 {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vaudio_reg: vaudio {
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + violo_reg: violo {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + viohi_reg: viohi {
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vgen_reg: vgen {
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vcam_reg: vcam {
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + };
> +
> + vrf1_reg: vrf1 {
> + regulator-min-microvolt = <2775000>;
> + regulator-max-microvolt = <2775000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vrf2_reg: vrf2 {
> + regulator-min-microvolt = <2775000>;
> + regulator-max-microvolt = <2775000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vmmc1_reg: vmmc1 {
> + regulator-min-microvolt = <1600000>;
> + regulator-max-microvolt = <3000000>;
> + };
> +
> + gpo1_reg: gpo1 { };
> +
> + pwgt1spi_reg: pwgt1spi {
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> &nfc {
> nand-bus-width = <8>;
> nand-ecc-mode = "hw";
> --
> 1.8.1.5
>
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
next prev parent reply other threads:[~2013-05-03 17:04 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-05-03 8:08 [PATCH v2] ARM: dts: Add SPI support for i.MX27 Phytec PCM038 module Alexander Shiyan
2013-05-03 17:04 ` Sascha Hauer [this message]
2013-05-04 12:40 ` Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20130503170434.GV32299@pengutronix.de \
--to=s.hauer@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).