[PATCH 3/3] ARM: mach-shmobile: lager: support GPIO switches

[horms@verge.net.au (Simon Horman)]

On Tue, May 14, 2013 at 12:35:20AM +0200, Laurent Pinchart wrote:
> Hi Simon,
> 
> Thank you for the patch.
> 
> On Monday 13 May 2013 17:53:53 Simon Horman wrote:
> > The lager board has pins 1 - 4 of SW2 wired up to GPIO pins.
> > This patch allows access to those pins as KEYS 1 - 4 using
> > gpio-keys.
> > 
> > Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
> > 
> > ---
> > 
> > This patch has run time dependencies on
> > 1. "gpio-rcar: Add support for IRQ_TYPE_EDGE_BOTH"
> > 2. "ARM: shmobile: r8a7790: Configure R-Car GPIO for IRQ_TYPE_EDGE_BOTH"
> > 
> > Without those dependencies satisfied the gpio-keys driver will
> > fail to be initialise itself. The boot should be otherwise successful
> > and the board otherwise functional.
> > ---
> >  arch/arm/mach-shmobile/board-lager.c | 22 ++++++++++++++++++++++
> >  1 file changed, 22 insertions(+)
> > 
> > diff --git a/arch/arm/mach-shmobile/board-lager.c
> > b/arch/arm/mach-shmobile/board-lager.c index 6a1ba38..4d1b42b 100644
> > --- a/arch/arm/mach-shmobile/board-lager.c
> > +++ b/arch/arm/mach-shmobile/board-lager.c
> > @@ -18,7 +18,10 @@
> >   * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 
> > USA */
> > 
> > +#include <linux/gpio.h>
> > +#include <linux/gpio_keys.h>
> >  #include <linux/interrupt.h>
> > +#include <linux/input.h>
> 
> My dictionary lists input before interrupt :-)

Thanks, I will fix that.

> >  #include <linux/irqchip.h>
> >  #include <linux/kernel.h>
> >  #include <linux/leds.h>
> > @@ -52,6 +55,22 @@ static struct gpio_led_platform_data lager_leds_pdata = {
> > .num_leds	= ARRAY_SIZE(lager_leds),
> >  };
> > 
> > +/* GPIO KEY */
> > +#define GPIO_KEY(c, g, d, ...) \
> > +	{ .code = c, .gpio = g, .desc = d, .active_low = 1 }
> > +
> > +static struct gpio_keys_button gpio_buttons[] = {
> > +	GPIO_KEY(KEY_4,		RCAR_GP_PIN(1, 28),	"SW2-pin4"),
> > +	GPIO_KEY(KEY_3,		RCAR_GP_PIN(1, 26),	"SW2-pin3"),
> > +	GPIO_KEY(KEY_2,		RCAR_GP_PIN(1, 24),	"SW2-pin2"),
> > +	GPIO_KEY(KEY_1,		RCAR_GP_PIN(1, 14),	"SW2-pin1"),
> > +};
> > +
> > +static struct gpio_keys_platform_data lager_keys_pdata = {
> > +	.buttons	= gpio_buttons,
> > +	.nbuttons	= ARRAY_SIZE(gpio_buttons),
> > +};
> > +
> 
> Could you please also update the lager dts file ?

I wonder if in that case we can remove the C code above.
And probably the C code for the GPIO leds too.

Magnus, could you clarify how you would like
C-code and DTS to look on the lager board?

> >  static const struct pinctrl_map lager_pinctrl_map[] = {
> >  	/* SCIF0 (CN19: DEBUG SERIAL0) */
> >  	PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.6", "pfc-r8a7790",
> > @@ -73,6 +92,9 @@ static void __init lager_add_standard_devices(void)
> >  	platform_device_register_data(&platform_bus, "leds-gpio", -1,
> >  				      &lager_leds_pdata,
> >  				      sizeof(lager_leds_pdata));
> > +	platform_device_register_data(&platform_bus, "gpio-keys", -1,
> > +				      &lager_keys_pdata,
> > +				      sizeof(lager_keys_pdata));
> >  }
> > 
> >  static const char *lager_boards_compat_dt[] __initdata = {