[PATCH v2] gpio-rcar: Add support for IRQ_TYPE_EDGE_BOTH

[magnus.damm@gmail.com (Magnus Damm)]

From: Simon Horman <horms+renesas@verge.net.au>

As hardware support for this feature is not universal for all SoCs a flag,
has_both_edge_trigger, has been added to the platform data of the driver to
allow this feature to be enabled.

The motivation for this is to allow use of the gpio-keys driver on the
lager board which is based on the r8a7790 SoC. The V2 of this patch has been
fully exercised using that driver on that board.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Magnus Damm <damm@opensource.se>
---

 Changes since V1:
 - Modified code to always set BOTHEDGE register if available
 - Set BOTHEDGE before IOINTSEL
 - Successfully tested triggering on both edges with SW2 on Lager

 drivers/gpio/gpio-rcar.c                |   26 +++++++++++++++++++++-----
 include/linux/platform_data/gpio-rcar.h |    1 +
 2 files changed, 22 insertions(+), 5 deletions(-)

--- 0001/drivers/gpio/gpio-rcar.c
+++ work/drivers/gpio/gpio-rcar.c	2013-05-24 18:39:54.000000000 +0900
@@ -49,6 +49,7 @@ struct gpio_rcar_priv {
 #define POSNEG 0x20
 #define EDGLEVEL 0x24
 #define FILONOFF 0x28
+#define BOTHEDGE 0x4c
 
 static inline u32 gpio_rcar_read(struct gpio_rcar_priv *p, int offs)
 {
@@ -91,7 +92,8 @@ static void gpio_rcar_irq_enable(struct
 static void gpio_rcar_config_interrupt_input_mode(struct gpio_rcar_priv *p,
 						  unsigned int hwirq,
 						  bool active_high_rising_edge,
-						  bool level_trigger)
+						  bool level_trigger,
+						  bool both)
 {
 	unsigned long flags;
 
@@ -108,6 +110,10 @@ static void gpio_rcar_config_interrupt_i
 	/* Configure edge or level trigger in EDGLEVEL */
 	gpio_rcar_modify_bit(p, EDGLEVEL, hwirq, !level_trigger);
 
+	/* Select one edge or both edges in BOTHEDGE */
+	if (p->config.has_both_edge_trigger)
+		gpio_rcar_modify_bit(p, BOTHEDGE, hwirq, both);
+
 	/* Select "Interrupt Input Mode" in IOINTSEL */
 	gpio_rcar_modify_bit(p, IOINTSEL, hwirq, true);
 
@@ -127,16 +133,26 @@ static int gpio_rcar_irq_set_type(struct
 
 	switch (type & IRQ_TYPE_SENSE_MASK) {
 	case IRQ_TYPE_LEVEL_HIGH:
-		gpio_rcar_config_interrupt_input_mode(p, hwirq, true, true);
+		gpio_rcar_config_interrupt_input_mode(p, hwirq, true, true,
+						      false);
 		break;
 	case IRQ_TYPE_LEVEL_LOW:
-		gpio_rcar_config_interrupt_input_mode(p, hwirq, false, true);
+		gpio_rcar_config_interrupt_input_mode(p, hwirq, false, true,
+						      false);
 		break;
 	case IRQ_TYPE_EDGE_RISING:
-		gpio_rcar_config_interrupt_input_mode(p, hwirq, true, false);
+		gpio_rcar_config_interrupt_input_mode(p, hwirq, true, false,
+						      false);
 		break;
 	case IRQ_TYPE_EDGE_FALLING:
-		gpio_rcar_config_interrupt_input_mode(p, hwirq, false, false);
+		gpio_rcar_config_interrupt_input_mode(p, hwirq, false, false,
+						      false);
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		if (!p->config.has_both_edge_trigger)
+			return -EINVAL;
+		gpio_rcar_config_interrupt_input_mode(p, hwirq, true, false,
+						      true);
 		break;
 	default:
 		return -EINVAL;
--- 0001/include/linux/platform_data/gpio-rcar.h
+++ work/include/linux/platform_data/gpio-rcar.h	2013-05-24 18:25:06.000000000 +0900
@@ -21,6 +21,7 @@ struct gpio_rcar_config {
 	unsigned int irq_base;
 	unsigned int number_of_pins;
 	const char *pctl_name;
+	unsigned has_both_edge_trigger:1;
 };
 
 #define RCAR_GP_PIN(bank, pin)		(((bank) * 32) + (pin))