From mboxrd@z Thu Jan  1 00:00:00 1970
From: w@1wt.eu (Willy Tarreau)
Date: Thu, 25 Jul 2013 07:40:36 +0200
Subject: Mainline kernel on snowball
In-Reply-To: <20130725052317.GA25854@verge.net.au>
References: <20130725052317.GA25854@verge.net.au>
Message-ID: <20130725054036.GD31954@1wt.eu>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

Hi Simon,

On Thu, Jul 25, 2013 at 02:23:17PM +0900, Simon Horman wrote:
> Hi,
> 
> I apologise for the na?ve nature of this question,
> but I do not seem to be able to make any progress of my own accord.
> 
> I would like to boot the mainline kernel - ideally v3.10 and v3.11-rcX -
> on snowball. The reason being to verify CPU hotplug which
> seems to be broken on shmobile, though that is tangential to this post.
> 
> My procedure, which does not work, is as follows.
> I have tried a number of different versions all with roughly
> the same result.
> 
> 1. Build kernel
> # git checkout v3.10.2 # I have tried several over versions too.
> # make u8500_defconfig
> Edit .config to enable CONFIG_ARM_APPENDED_DTB
> # LOADADDR=0x100000 make uImage dtbs
> 
> 2. Append dtb to zImage and recreate uImage
> mv arch/arm/boot/zImage arch/arm/boot/zImage.tmp
> cat arch/arm/boot/zImage.tmp arch/arm/boot/dts/snowball.dtb
> /bin/sh scripts/mkuboot.sh \
> 	-A arm -O linux -C none  -T kernel \
> 	-a 0x100000 -e 0x100000 -n 'Linux-3.10.2' \
> 	-d arch/arm/boot/zImage arch/arm/boot/uImage
> 
> 3. Boot uImage from u-boot
> Snowball $ setenv ethaddr 3e:c4:73:05:d1:a1
> Snowball $ bootp;bootm
> smc911x: detected LAN9221 controller
> smc911x: phy initialized
> smc911x: MAC 3e:c4:73:05:d1:a1
> BOOTP broadcast 1
> *** Unhandled DHCP Option in OFFER/ACK: 28
> *** Unhandled DHCP Option in OFFER/ACK: 44
> *** Unhandled DHCP Option in OFFER/ACK: 28
> *** Unhandled DHCP Option in OFFER/ACK: 44
> DHCP client bound to address 10.3.3.146
> Using smc911x-0 device
> TFTP from server 10.3.3.135; our IP address is 10.3.3.146
> Filename 'snowball/uImage'.
> Load address: 0x100000
> Loading: #################################################################
>          #################################################################
>          #################################################################
>          #################################################################
>          ##########################################################
> done
> Bytes transferred = 2540191 (26c29f hex)
> ## Booting kernel from Legacy Image at 00100000 ...
>    Image Name:   'Linux-3.10.2'
>    Image Type:   ARM Linux Kernel Image (uncompressed)
>    Data Size:    2540127 Bytes =  2.4 MB
>    Load Address: 00100000
>    Entry Point:  00100000
>    XIP Kernel Image ... OK
> OK
> 
> Starting kernel ...
> 
> 
> This is as far as it gets.

Are you sure you have the correct bootargs by default ? It was a
pain for me to figure the correct ones, and I finally found them
in the boot scripts. Mine is booted with this :

# cat /proc/cmdline 
console=tty0 console=ttyAMA2,115200n8  root=UUID=018e1580-e7e9-460b-95c5-236f6b87b13d rootwait ro fixrtc nocompcache vmalloc=300M mem=128M at 0 mali.mali_mem=64M at 128M hwmem=168M at 192M mem=22M at 360M mem_issw=1M at 383M mem=640M at 384M

# uname -a
Linux snowball 3.10.0-rc5-snowball #2 SMP Fri Jun 14 09:19:28 CEST 2013 armv7l GNU/Linux

I don't have the CONFIG_ARM_APPENDED_DTB set, instead I have copied
the dtb on the flash since u-boot supports it (I find this boot
procedure quite annoying btw).

Hoping this helps,
Willy