[PATCH] ARM: sunxi: dt: Add device tree for Mele A1000

[PATCH] ARM: sunxi: dt: Add device tree for Mele A1000

[Emilio López]

This adds a device tree usable on Mele A1000 (and A2000, as it
apparently is the same device except for the case). This device features
one UART port, Ethernet, an AXP209 PMU on i2c0 and two user configurable
LEDs.

Signed-off-by: Emilio L?pez <emilio@elopez.com.ar>
---

This has been tested by arokux on #linux-sunxi in Freenode and found to 
work correctly.

 arch/arm/boot/dts/Makefile            |   1 +
 arch/arm/boot/dts/sun4i-a10-a1000.dts | 106 ++++++++++++++++++++++++++++++++++
 2 files changed, 107 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun4i-a10-a1000.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 641b3c9..3fd3919 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -206,6 +206,7 @@ dtb-$(CONFIG_ARCH_STI)+= stih415-b2000.dtb \
 	stih415-b2020.dtb \
 	stih416-b2020.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += \
+	sun4i-a10-a1000.dtb \
 	sun4i-a10-cubieboard.dtb \
 	sun4i-a10-mini-xplus.dtb \
 	sun4i-a10-hackberry.dtb \
diff --git a/arch/arm/boot/dts/sun4i-a10-a1000.dts b/arch/arm/boot/dts/sun4i-a10-a1000.dts
new file mode 100644
index 0000000..304a38e
--- /dev/null
+++ b/arch/arm/boot/dts/sun4i-a10-a1000.dts
@@ -0,0 +1,106 @@
+/*
+ * Copyright 2013 Emilio L?pez
+ *
+ * Emilio L?pez <emilio@elopez.com.ar>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "sun4i-a10.dtsi"
+
+/ {
+	model = "Mele A1000";
+	compatible = "mele,a1000", "allwinner,sun4i-a10";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		bootargs = "earlyprintk console=ttyS0,115200";
+	};
+
+	soc at 01c20000 {
+		emac: ethernet at 01c0b000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&emac_pins_a>;
+			phy = <&phy1>;
+			status = "okay";
+		};
+
+		mdio at 01c0b080 {
+			phy-supply = <&reg_emac_3v3>;
+			status = "okay";
+
+			phy1: ethernet-phy at 1 {
+				reg = <1>;
+			};
+		};
+
+		pinctrl at 01c20800 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&a1000_hogs>;
+
+			a1000_hogs: hogs at 0 {
+				allwinner,pins = "PH15";
+				allwinner,function = "gpio_out";
+				allwinner,drive = <0>;
+				allwinner,pull = <0>;
+			};
+
+			led_pins_a1000: led_pins at 0 {
+				allwinner,pins = "PH10", "PH20";
+				allwinner,function = "gpio_out";
+				allwinner,drive = <1>;
+				allwinner,pull = <0>;
+			};
+		};
+
+		uart0: serial at 01c28000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_pins_a>;
+			status = "okay";
+		};
+
+		i2c0: i2c at 01c2ac00 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins_a>;
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_a1000>;
+
+		red {
+			label = "a1000:red:usr";
+			gpios = <&pio 7 10 0>;
+		};
+
+		blue {
+			label = "a1000:blue:usr";
+			gpios = <&pio 7 20 0>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_emac_3v3: emac-3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "emac-3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			enable-active-high;
+			gpio = <&pio 7 15 0>;
+		};
+	};
+};
-- 
1.8.3.4

[PATCH] ARM: sunxi: dt: Add device tree for Mele A1000

[Maxime Ripard]

Hi Emilio,

On Tue, Aug 13, 2013 at 04:07:45PM -0300, Emilio L?pez wrote:
> This adds a device tree usable on Mele A1000 (and A2000, as it
> apparently is the same device except for the case). This device features
> one UART port, Ethernet, an AXP209 PMU on i2c0 and two user configurable
> LEDs.
> 
> Signed-off-by: Emilio L?pez <emilio@elopez.com.ar>
> ---
> 
> This has been tested by arokux on #linux-sunxi in Freenode and found to 
> work correctly.
>
>  arch/arm/boot/dts/Makefile            |   1 +
>  arch/arm/boot/dts/sun4i-a10-a1000.dts | 106 ++++++++++++++++++++++++++++++++++
>  2 files changed, 107 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun4i-a10-a1000.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 641b3c9..3fd3919 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -206,6 +206,7 @@ dtb-$(CONFIG_ARCH_STI)+= stih415-b2000.dtb \
>  	stih415-b2020.dtb \
>  	stih416-b2020.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += \
> +	sun4i-a10-a1000.dtb \
>  	sun4i-a10-cubieboard.dtb \
>  	sun4i-a10-mini-xplus.dtb \
>  	sun4i-a10-hackberry.dtb \
> diff --git a/arch/arm/boot/dts/sun4i-a10-a1000.dts b/arch/arm/boot/dts/sun4i-a10-a1000.dts
> new file mode 100644
> index 0000000..304a38e
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun4i-a10-a1000.dts
> @@ -0,0 +1,106 @@
> +/*
> + * Copyright 2013 Emilio L?pez
> + *
> + * Emilio L?pez <emilio@elopez.com.ar>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +/include/ "sun4i-a10.dtsi"
> +
> +/ {
> +	model = "Mele A1000";
> +	compatible = "mele,a1000", "allwinner,sun4i-a10";
> +
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		bootargs = "earlyprintk console=ttyS0,115200";
> +	};

That's not quite useful anymore now that we have a DT-aware bootloader,
I'd remove it.

> +
> +	soc at 01c20000 {
> +		emac: ethernet at 01c0b000 {
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&emac_pins_a>;
> +			phy = <&phy1>;
> +			status = "okay";
> +		};
> +
> +		mdio at 01c0b080 {
> +			phy-supply = <&reg_emac_3v3>;
> +			status = "okay";
> +
> +			phy1: ethernet-phy at 1 {
> +				reg = <1>;
> +			};
> +		};
> +
> +		pinctrl at 01c20800 {
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&a1000_hogs>;
> +
> +			a1000_hogs: hogs at 0 {
> +				allwinner,pins = "PH15";
> +				allwinner,function = "gpio_out";
> +				allwinner,drive = <0>;
> +				allwinner,pull = <0>;
> +			};

Why using the hog pins here? I don't think you require it anymore, just
grab the pinctrl node from the regulator, it should work, right?

> +
> +			led_pins_a1000: led_pins at 0 {
> +				allwinner,pins = "PH10", "PH20";
> +				allwinner,function = "gpio_out";
> +				allwinner,drive = <1>;

Do you really need the extra 10 mA here?

> +				allwinner,pull = <0>;
> +			};
> +		};
> +
> +		uart0: serial at 01c28000 {
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&uart0_pins_a>;
> +			status = "okay";
> +		};
> +
> +		i2c0: i2c at 01c2ac00 {
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&i2c0_pins_a>;
> +			status = "okay";
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&led_pins_a1000>;
> +
> +		red {
> +			label = "a1000:red:usr";
> +			gpios = <&pio 7 10 0>;
> +		};
> +
> +		blue {
> +			label = "a1000:blue:usr";
> +			gpios = <&pio 7 20 0>;
> +		};
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";
> +
> +		reg_emac_3v3: emac-3v3 {
> +			compatible = "regulator-fixed";
> +			regulator-name = "emac-3v3";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			enable-active-high;
> +			gpio = <&pio 7 15 0>;
> +		};
> +	};
> +};
> -- 
> 1.8.3.4
> 

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20130813/eb6377c4/attachment.sig>

[PATCH v2] ARM: sunxi: dt: Add device tree for Mele A1000

[Emilio López]

This adds a device tree usable on Mele A1000 (and A2000, as it
apparently is the same device except for the case). This device features
one UART port, Ethernet, an AXP209 PMU on i2c0 and two user configurable
LEDs.

Signed-off-by: Emilio L?pez <emilio@elopez.com.ar>
---

Maxime, this v2 should address all your comments.

Cheers,

Emilio

 arch/arm/boot/dts/Makefile            |   1 +
 arch/arm/boot/dts/sun4i-a10-a1000.dts | 101 ++++++++++++++++++++++++++++++++++
 2 files changed, 102 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun4i-a10-a1000.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 641b3c9..3fd3919 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -206,6 +206,7 @@ dtb-$(CONFIG_ARCH_STI)+= stih415-b2000.dtb \
 	stih415-b2020.dtb \
 	stih416-b2020.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += \
+	sun4i-a10-a1000.dtb \
 	sun4i-a10-cubieboard.dtb \
 	sun4i-a10-mini-xplus.dtb \
 	sun4i-a10-hackberry.dtb \
diff --git a/arch/arm/boot/dts/sun4i-a10-a1000.dts b/arch/arm/boot/dts/sun4i-a10-a1000.dts
new file mode 100644
index 0000000..0b2e9d7
--- /dev/null
+++ b/arch/arm/boot/dts/sun4i-a10-a1000.dts
@@ -0,0 +1,101 @@
+/*
+ * Copyright 2013 Emilio L?pez
+ *
+ * Emilio L?pez <emilio@elopez.com.ar>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "sun4i-a10.dtsi"
+
+/ {
+	model = "Mele A1000";
+	compatible = "mele,a1000", "allwinner,sun4i-a10";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	soc at 01c20000 {
+		emac: ethernet at 01c0b000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&emac_pins_a>;
+			phy = <&phy1>;
+			status = "okay";
+		};
+
+		mdio at 01c0b080 {
+			phy-supply = <&reg_emac_3v3>;
+			status = "okay";
+
+			phy1: ethernet-phy at 1 {
+				reg = <1>;
+			};
+		};
+
+		pinctrl at 01c20800 {
+			emac_power_pin_a1000: emac_power_pin at 0 {
+				allwinner,pins = "PH15";
+				allwinner,function = "gpio_out";
+				allwinner,drive = <0>;
+				allwinner,pull = <0>;
+			};
+
+			led_pins_a1000: led_pins at 0 {
+				allwinner,pins = "PH10", "PH20";
+				allwinner,function = "gpio_out";
+				allwinner,drive = <0>;
+				allwinner,pull = <0>;
+			};
+		};
+
+		uart0: serial at 01c28000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_pins_a>;
+			status = "okay";
+		};
+
+		i2c0: i2c at 01c2ac00 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins_a>;
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_a1000>;
+
+		red {
+			label = "a1000:red:usr";
+			gpios = <&pio 7 10 0>;
+		};
+
+		blue {
+			label = "a1000:blue:usr";
+			gpios = <&pio 7 20 0>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_emac_3v3: emac-3v3 {
+			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&emac_power_pin_a1000>;
+			regulator-name = "emac-3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			enable-active-high;
+			gpio = <&pio 7 15 0>;
+		};
+	};
+};
-- 
1.8.3.4

[PATCH v2] ARM: sunxi: dt: Add device tree for Mele A1000

[Maxime Ripard]

On Tue, Aug 13, 2013 at 08:18:21PM -0300, Emilio L?pez wrote:
> This adds a device tree usable on Mele A1000 (and A2000, as it
> apparently is the same device except for the case). This device features
> one UART port, Ethernet, an AXP209 PMU on i2c0 and two user configurable
> LEDs.
> 
> Signed-off-by: Emilio L?pez <emilio@elopez.com.ar>

Applied with a minor fix to the soc node address on my sunxi/dt-for-3.12
branch.

Thanks,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20130814/bcbfefa0/attachment.sig>

[PATCH] ARM: sunxi: dt: Add device tree for Mele A1000

[Maxime Ripard]

On Wed, Aug 14, 2013 at 02:50:14AM +0200, Arokux X wrote:
> Tested-by: Arokux <arokux@gmail.com>

We won't take any contributions using a pseudonym. Please use your real
name.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20130814/b633e4c3/attachment-0001.sig>