[PATCH 09/33] ARM: ux500: Supply the I2C clocks lookup to the DBX500 DT

[lee.jones@linaro.org (Lee Jones)]

On Tue, 27 Aug 2013, Mark Rutland wrote:

> On Tue, Aug 27, 2013 at 09:06:35AM +0100, Lee Jones wrote:
> > On Fri, 23 Aug 2013, Mark Rutland wrote:
> > 
> > > On Fri, Aug 23, 2013 at 08:56:07AM +0100, Lee Jones wrote:
> > > > I had a short chat with Rob last night about this. I'm going to loop
> > > > him in to the conversation, as he wrote the binding.
> > > > 
> > > > > > When most of the other clocks that we deal with are being requested,
> > > > > > they rely on being index zero:
> > > > > > 
> > > > > >   drivers/i2c/busses/i2c-nomadik.c: dev->clk = clk_get(&adev->dev, NULL);
> > > > > 
> > > > > Look at drivers/clk/clkdev.c, there's some fuzzy matching
> > > > > involved when you pass NULL as connection id.
> > > > 
> > > > Yes, I've been looking at that. This is why it works currently. I
> > > > think I need to change all of the drivers to specify which clock they
> > > > want. At the moment that 'fuzzy matching' is what's saving us. If
> > > > anyone were to change our DTS file to match what the binding says,
> > > > then it would cease to work. I'm guessing this is the same for all
> > > > other DTS files too:
> > > 
> > > I think if anything, the binding document(s) should be updated to
> > > describe that apb_pclk is referred to by name, and the names of the
> > > other clocks should be described in the specific device bindings. We can
> > > then modify the drivers which grab clock 0 to explicitly grab the first
> > > clock by name, and backwards compatibility should not be broken.
> > > 
> > > I don't believe any other OS has implemented the common clock bindings,
> > > and we've never supported the binding as described. Let's correct the
> > > de-facto standard into a standard by decree.
> > 
> > I think we need to respect, or at least take into consideration the
> > reason for the original 'de-facto' standard. Other OSes shouldn't be
> > forced to provide a named clock request in order to obtain
> > 'apb_pclk'. If the binding says it should be first, then perhaps we
> > should do just that. It's simply a matter of naming all subsequent
> > clocks related to AMBA devices.
> 
> Ideally, yes. However, we have to be careful to not break compatibility.
> 
> I took a look at existing primecell drivers and what they do. The
> situation isn't so bad (with the exception of the
> half-dt/half-platform-code mess):
> 
> * Some don't deal with clocks at all (no clk* in the driver). pl320 is
>   in the ecx-common dtsi with only apb_pclk but has no binding
>   defined. Some have no clocks defined in the dt and are presumably few
>   clocks by platform data or are non-functional.
> 
>   I'm not sure how these DTs are going to be supported if and when we
>   remove the platform data they depend upon. If we're really going to do
>   that, then they are clearly not supported as-is long term.
> 
> * The pl022 driver grabs the first clock to figure out the rate of the
>   spi bus (assuming it is SSPCLK). The SSPCLK input is not defined in
>   the binding. The ste-u300 dts has two clock-names, "apb_pclk" and
>   "spi_clk" (in that order), but they refer to the same clock.
> 
>   Given the existing driver simply grabs the first clock and they're
>   both the same, we could re-order the names and make the driver grab
>   the second clock. That wouldn't break backwards compatibility with the
>   sole dts file we have using the binding, though this assumes no-one
>   else has a dt lying around with different clocks.
> 
> * pl010 grabs the first clock given to it to figure out the uart rate
>   (assuming it is UARTCLK), but it's only in integratorap.dts, without
>   clocks, and is presumably fed by platform data. There is no binding
>   document.
> 
>   pl011 grabs the first clock given to figure out the UART rate
>   (assuming it is UARTCLK). The binding explicitly states it's only
>   given apb_pclk, despite UARTCLK and PCLK being separate inputs to the
>   IP block.
> 
>   These two bindings don't describe the hardware, and should be fixed.
>   The only way I can think to make this work without breaknig backwards
>   compatibility would be to try to grab the second clock and then fall
>   back to the first if there isn't one. The other option is to break
>   backwards compatibility, but I'm not sure that's much of an option.
> 
> * pl111 has no driver or binding in mainline, but appears in dts files.
>   Those dts files clcdclk and apb_pclk, in that order. We could fix
>   those before a driver starts using them.
> 
> If you think those suggestions are OK, I can put together a series to
> fix this.

I think we need to hear from Rob before we proceed tbh, as he is the
original author and should have a chance to voice his opinion.

-- 
Lee Jones
Linaro ST-Ericsson Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog