* [PATCH v5 0/8] ARM: imx27 pinctrl
@ 2013-10-24 15:38 Markus Pargmann
2013-10-24 15:38 ` [PATCH v5 1/8] pinctrl: imx1 core driver Markus Pargmann
` (7 more replies)
0 siblings, 8 replies; 11+ messages in thread
From: Markus Pargmann @ 2013-10-24 15:38 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
v5 contains a small new fix which moves uart1 from phycore SOM to RDK dts file.
The uart1 pinctrl is added to RDK only.
this series implements a imx27 pinctrl driver. imx1/21/27 have a register
format that is not compatible with the rest of imx series processors. The
series adds a imx1 core driver for the different register layout.
Regards,
Markus
Markus Pargmann (8):
pinctrl: imx1 core driver
pinctrl: imx27: imx27 pincontrol driver
ARM: dts: imx27 pin functions
ARM: dts: imx27 pinctrl
ARM: dts: imx27 phyCARD-S pinctrl
ARM: dts: imx27 phycore move uart1 to rdk
ARM: dts: imx27 phycore pinctrl
ARM: imx27: enable pinctrl
.../bindings/pinctrl/fsl,imx27-pinctrl.txt | 50 ++
arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts | 10 +
arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts | 4 +
arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts | 5 +
arch/arm/boot/dts/imx27-phytec-phycore-som.dts | 8 +-
arch/arm/boot/dts/imx27-pinfunc.h | 524 +++++++++++++++++
arch/arm/boot/dts/imx27.dtsi | 102 ++++
arch/arm/mach-imx/Kconfig | 2 +
drivers/pinctrl/Kconfig | 13 +
drivers/pinctrl/Makefile | 2 +
drivers/pinctrl/pinctrl-imx1-core.c | 653 +++++++++++++++++++++
drivers/pinctrl/pinctrl-imx1.h | 73 +++
drivers/pinctrl/pinctrl-imx27.c | 477 +++++++++++++++
13 files changed, 1919 insertions(+), 4 deletions(-)
create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt
create mode 100644 arch/arm/boot/dts/imx27-pinfunc.h
create mode 100644 drivers/pinctrl/pinctrl-imx1-core.c
create mode 100644 drivers/pinctrl/pinctrl-imx1.h
create mode 100644 drivers/pinctrl/pinctrl-imx27.c
--
1.8.4.rc3
^ permalink raw reply [flat|nested] 11+ messages in thread* [PATCH v5 1/8] pinctrl: imx1 core driver 2013-10-24 15:38 [PATCH v5 0/8] ARM: imx27 pinctrl Markus Pargmann @ 2013-10-24 15:38 ` Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 2/8] pinctrl: imx27: imx27 pincontrol driver Markus Pargmann ` (6 subsequent siblings) 7 siblings, 0 replies; 11+ messages in thread From: Markus Pargmann @ 2013-10-24 15:38 UTC (permalink / raw) To: linux-arm-kernel Core driver for register formats of imx1/imx21/imx27 processors. The pins of those processors are grouped into ports. Each port has 32 pins. The pins mux configuration is controlled by registers with 1 or 2 bit per pin, depending on the specific control register. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Shawn Guo <shawn.guo@linaro.org> --- drivers/pinctrl/Kconfig | 5 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-imx1-core.c | 653 ++++++++++++++++++++++++++++++++++++ drivers/pinctrl/pinctrl-imx1.h | 73 ++++ 4 files changed, 732 insertions(+) create mode 100644 drivers/pinctrl/pinctrl-imx1-core.c create mode 100644 drivers/pinctrl/pinctrl-imx1.h diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index b6e864e..8a02aa0 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -80,6 +80,11 @@ config PINCTRL_IMX select PINMUX select PINCONF +config PINCTRL_IMX1_CORE + bool + select PINMUX + select PINCONF + config PINCTRL_IMX35 bool "IMX35 pinctrl driver" depends on OF diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index 496d9bf..d7caf08 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -18,6 +18,7 @@ obj-$(CONFIG_PINCTRL_AT91) += pinctrl-at91.o obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o obj-$(CONFIG_PINCTRL_BAYTRAIL) += pinctrl-baytrail.o obj-$(CONFIG_PINCTRL_IMX) += pinctrl-imx.o +obj-$(CONFIG_PINCTRL_IMX1_CORE) += pinctrl-imx1-core.o obj-$(CONFIG_PINCTRL_IMX35) += pinctrl-imx35.o obj-$(CONFIG_PINCTRL_IMX51) += pinctrl-imx51.o obj-$(CONFIG_PINCTRL_IMX53) += pinctrl-imx53.o diff --git a/drivers/pinctrl/pinctrl-imx1-core.c b/drivers/pinctrl/pinctrl-imx1-core.c new file mode 100644 index 0000000..4d5a9e7 --- /dev/null +++ b/drivers/pinctrl/pinctrl-imx1-core.c @@ -0,0 +1,653 @@ +/* + * Core driver for the imx pin controller in imx1/21/27 + * + * Copyright (C) 2013 Pengutronix + * Author: Markus Pargmann <mpa@pengutronix.de> + * + * Based on pinctrl-imx.c: + * Author: Dong Aisheng <dong.aisheng@linaro.org> + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * Copyright (C) 2012 Linaro Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/bitops.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/pinctrl/machine.h> +#include <linux/pinctrl/pinconf.h> +#include <linux/pinctrl/pinctrl.h> +#include <linux/pinctrl/pinmux.h> +#include <linux/slab.h> + +#include "core.h" +#include "pinctrl-imx1.h" + +struct imx1_pinctrl { + struct device *dev; + struct pinctrl_dev *pctl; + void __iomem *base; + const struct imx1_pinctrl_soc_info *info; +}; + +/* + * MX1 register offsets + */ + +#define MX1_DDIR 0x00 +#define MX1_OCR 0x04 +#define MX1_ICONFA 0x0c +#define MX1_ICONFB 0x10 +#define MX1_GIUS 0x20 +#define MX1_GPR 0x38 +#define MX1_PUEN 0x40 + +#define MX1_PORT_STRIDE 0x100 + + +/* + * MUX_ID format defines + */ +#define MX1_MUX_FUNCTION(val) (BIT(0) & val) +#define MX1_MUX_GPIO(val) ((BIT(1) & val) >> 1) +#define MX1_MUX_DIR(val) ((BIT(2) & val) >> 2) +#define MX1_MUX_OCONF(val) (((BIT(4) | BIT(5)) & val) >> 4) +#define MX1_MUX_ICONFA(val) (((BIT(8) | BIT(9)) & val) >> 8) +#define MX1_MUX_ICONFB(val) (((BIT(10) | BIT(11)) & val) >> 10) + + +/* + * IMX1 IOMUXC manages the pins based on ports. Each port has 32 pins. IOMUX + * control register are seperated into function, output configuration, input + * configuration A, input configuration B, GPIO in use and data direction. + * + * Those controls that are represented by 1 bit have a direct mapping between + * bit position and pin id. If they are represented by 2 bit, the lower 16 pins + * are in the first register and the upper 16 pins in the second (next) + * register. pin_id is stored in bit (pin_id%16)*2 and the bit above. + */ + +/* + * Calculates the register offset from a pin_id + */ +static void __iomem *imx1_mem(struct imx1_pinctrl *ipctl, unsigned int pin_id) +{ + unsigned int port = pin_id / 32; + return ipctl->base + port * MX1_PORT_STRIDE; +} + +/* + * Write to a register with 2 bits per pin. The function will automatically + * use the next register if the pin is managed in the second register. + */ +static void imx1_write_2bit(struct imx1_pinctrl *ipctl, unsigned int pin_id, + u32 value, u32 reg_offset) +{ + void __iomem *reg = imx1_mem(ipctl, pin_id) + reg_offset; + int offset = (pin_id % 16) * 2; /* offset, regardless of register used */ + int mask = ~(0x3 << offset); /* Mask for 2 bits@offset */ + u32 old_val; + u32 new_val; + + dev_dbg(ipctl->dev, "write: register 0x%p offset %d value 0x%x\n", + reg, offset, value); + + /* Use the next register if the pin's port pin number is >=16 */ + if (pin_id % 32 >= 16) + reg += 0x04; + + /* Get current state of pins */ + old_val = readl(reg); + old_val &= mask; + + new_val = value & 0x3; /* Make sure value is really 2 bit */ + new_val <<= offset; + new_val |= old_val;/* Set new state for pin_id */ + + writel(new_val, reg); +} + +static void imx1_write_bit(struct imx1_pinctrl *ipctl, unsigned int pin_id, + u32 value, u32 reg_offset) +{ + void __iomem *reg = imx1_mem(ipctl, pin_id) + reg_offset; + int offset = pin_id % 32; + int mask = ~BIT_MASK(offset); + u32 old_val; + u32 new_val; + + /* Get current state of pins */ + old_val = readl(reg); + old_val &= mask; + + new_val = value & 0x1; /* Make sure value is really 1 bit */ + new_val <<= offset; + new_val |= old_val;/* Set new state for pin_id */ + + writel(new_val, reg); +} + +static int imx1_read_2bit(struct imx1_pinctrl *ipctl, unsigned int pin_id, + u32 reg_offset) +{ + void __iomem *reg = imx1_mem(ipctl, pin_id) + reg_offset; + int offset = pin_id % 16; + + /* Use the next register if the pin's port pin number is >=16 */ + if (pin_id % 32 >= 16) + reg += 0x04; + + return (readl(reg) & (BIT(offset) | BIT(offset+1))) >> offset; +} + +static int imx1_read_bit(struct imx1_pinctrl *ipctl, unsigned int pin_id, + u32 reg_offset) +{ + void __iomem *reg = imx1_mem(ipctl, pin_id) + reg_offset; + int offset = pin_id % 32; + + return !!(readl(reg) & BIT(offset)); +} + +static const inline struct imx1_pin_group *imx1_pinctrl_find_group_by_name( + const struct imx1_pinctrl_soc_info *info, + const char *name) +{ + const struct imx1_pin_group *grp = NULL; + int i; + + for (i = 0; i < info->ngroups; i++) { + if (!strcmp(info->groups[i].name, name)) { + grp = &info->groups[i]; + break; + } + } + + return grp; +} + +static int imx1_get_groups_count(struct pinctrl_dev *pctldev) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + + return info->ngroups; +} + +static const char *imx1_get_group_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + + return info->groups[selector].name; +} + +static int imx1_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector, + const unsigned int **pins, + unsigned *npins) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + + if (selector >= info->ngroups) + return -EINVAL; + + *pins = info->groups[selector].pin_ids; + *npins = info->groups[selector].npins; + + return 0; +} + +static void imx1_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s, + unsigned offset) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + + seq_printf(s, "GPIO %d, function %d, direction %d, oconf %d, iconfa %d, iconfb %d", + imx1_read_bit(ipctl, offset, MX1_GIUS), + imx1_read_bit(ipctl, offset, MX1_GPR), + imx1_read_bit(ipctl, offset, MX1_DDIR), + imx1_read_2bit(ipctl, offset, MX1_OCR), + imx1_read_2bit(ipctl, offset, MX1_ICONFA), + imx1_read_2bit(ipctl, offset, MX1_ICONFB)); +} + +static int imx1_dt_node_to_map(struct pinctrl_dev *pctldev, + struct device_node *np, + struct pinctrl_map **map, unsigned *num_maps) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + const struct imx1_pin_group *grp; + struct pinctrl_map *new_map; + struct device_node *parent; + int map_num = 1; + int i, j; + + /* + * first find the group of this node and check if we need create + * config maps for pins + */ + grp = imx1_pinctrl_find_group_by_name(info, np->name); + if (!grp) { + dev_err(info->dev, "unable to find group for node %s\n", + np->name); + return -EINVAL; + } + + for (i = 0; i < grp->npins; i++) + map_num++; + + new_map = kmalloc(sizeof(struct pinctrl_map) * map_num, GFP_KERNEL); + if (!new_map) + return -ENOMEM; + + *map = new_map; + *num_maps = map_num; + + /* create mux map */ + parent = of_get_parent(np); + if (!parent) { + kfree(new_map); + return -EINVAL; + } + new_map[0].type = PIN_MAP_TYPE_MUX_GROUP; + new_map[0].data.mux.function = parent->name; + new_map[0].data.mux.group = np->name; + of_node_put(parent); + + /* create config map */ + new_map++; + for (i = j = 0; i < grp->npins; i++) { + new_map[j].type = PIN_MAP_TYPE_CONFIGS_PIN; + new_map[j].data.configs.group_or_pin = + pin_get_name(pctldev, grp->pins[i].pin_id); + new_map[j].data.configs.configs = &grp->pins[i].config; + new_map[j].data.configs.num_configs = 1; + j++; + } + + dev_dbg(pctldev->dev, "maps: function %s group %s num %d\n", + (*map)->data.mux.function, (*map)->data.mux.group, map_num); + + return 0; +} + +static void imx1_dt_free_map(struct pinctrl_dev *pctldev, + struct pinctrl_map *map, unsigned num_maps) +{ + kfree(map); +} + +static const struct pinctrl_ops imx1_pctrl_ops = { + .get_groups_count = imx1_get_groups_count, + .get_group_name = imx1_get_group_name, + .get_group_pins = imx1_get_group_pins, + .pin_dbg_show = imx1_pin_dbg_show, + .dt_node_to_map = imx1_dt_node_to_map, + .dt_free_map = imx1_dt_free_map, + +}; + +static int imx1_pmx_enable(struct pinctrl_dev *pctldev, unsigned selector, + unsigned group) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + const struct imx1_pin *pins; + unsigned int npins; + int i; + + /* + * Configure the mux mode for each pin in the group for a specific + * function. + */ + pins = info->groups[group].pins; + npins = info->groups[group].npins; + + WARN_ON(!pins || !npins); + + dev_dbg(ipctl->dev, "enable function %s group %s\n", + info->functions[selector].name, info->groups[group].name); + + for (i = 0; i < npins; i++) { + unsigned int mux = pins[i].mux_id; + unsigned int pin_id = pins[i].pin_id; + unsigned int afunction = MX1_MUX_FUNCTION(mux); + unsigned int gpio_in_use = MX1_MUX_GPIO(mux); + unsigned int direction = MX1_MUX_DIR(mux); + unsigned int gpio_oconf = MX1_MUX_OCONF(mux); + unsigned int gpio_iconfa = MX1_MUX_ICONFA(mux); + unsigned int gpio_iconfb = MX1_MUX_ICONFB(mux); + + dev_dbg(pctldev->dev, "%s, pin 0x%x, function %d, gpio %d, direction %d, oconf %d, iconfa %d, iconfb %d\n", + __func__, pin_id, afunction, gpio_in_use, + direction, gpio_oconf, gpio_iconfa, + gpio_iconfb); + + imx1_write_bit(ipctl, pin_id, gpio_in_use, MX1_GIUS); + imx1_write_bit(ipctl, pin_id, direction, MX1_DDIR); + + if (gpio_in_use) { + imx1_write_2bit(ipctl, pin_id, gpio_oconf, MX1_OCR); + imx1_write_2bit(ipctl, pin_id, gpio_iconfa, + MX1_ICONFA); + imx1_write_2bit(ipctl, pin_id, gpio_iconfb, + MX1_ICONFB); + } else { + imx1_write_bit(ipctl, pin_id, afunction, MX1_GPR); + } + } + + return 0; +} + +static int imx1_pmx_get_funcs_count(struct pinctrl_dev *pctldev) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + + return info->nfunctions; +} + +static const char *imx1_pmx_get_func_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + + return info->functions[selector].name; +} + +static int imx1_pmx_get_groups(struct pinctrl_dev *pctldev, unsigned selector, + const char * const **groups, + unsigned * const num_groups) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + + *groups = info->functions[selector].groups; + *num_groups = info->functions[selector].num_groups; + + return 0; +} + +static const struct pinmux_ops imx1_pmx_ops = { + .get_functions_count = imx1_pmx_get_funcs_count, + .get_function_name = imx1_pmx_get_func_name, + .get_function_groups = imx1_pmx_get_groups, + .enable = imx1_pmx_enable, +}; + +static int imx1_pinconf_get(struct pinctrl_dev *pctldev, + unsigned pin_id, unsigned long *config) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + + *config = imx1_read_bit(ipctl, pin_id, MX1_PUEN); + + return 0; +} + +static int imx1_pinconf_set(struct pinctrl_dev *pctldev, + unsigned pin_id, unsigned long *configs, + unsigned num_configs) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + int i; + + for (i = 0; i != num_configs; ++i) { + imx1_write_bit(ipctl, pin_id, configs[i] & 0x01, MX1_PUEN); + + dev_dbg(ipctl->dev, "pinconf set pullup pin %s\n", + info->pins[pin_id].name); + } + + return 0; +} + +static void imx1_pinconf_dbg_show(struct pinctrl_dev *pctldev, + struct seq_file *s, unsigned pin_id) +{ + unsigned long config; + + imx1_pinconf_get(pctldev, pin_id, &config); + seq_printf(s, "0x%lx", config); +} + +static void imx1_pinconf_group_dbg_show(struct pinctrl_dev *pctldev, + struct seq_file *s, unsigned group) +{ + struct imx1_pinctrl *ipctl = pinctrl_dev_get_drvdata(pctldev); + const struct imx1_pinctrl_soc_info *info = ipctl->info; + struct imx1_pin_group *grp; + unsigned long config; + const char *name; + int i, ret; + + if (group > info->ngroups) + return; + + seq_puts(s, "\n"); + grp = &info->groups[group]; + for (i = 0; i < grp->npins; i++) { + name = pin_get_name(pctldev, grp->pins[i].pin_id); + ret = imx1_pinconf_get(pctldev, grp->pins[i].pin_id, &config); + if (ret) + return; + seq_printf(s, "%s: 0x%lx", name, config); + } +} + +static const struct pinconf_ops imx1_pinconf_ops = { + .pin_config_get = imx1_pinconf_get, + .pin_config_set = imx1_pinconf_set, + .pin_config_dbg_show = imx1_pinconf_dbg_show, + .pin_config_group_dbg_show = imx1_pinconf_group_dbg_show, +}; + +static struct pinctrl_desc imx1_pinctrl_desc = { + .pctlops = &imx1_pctrl_ops, + .pmxops = &imx1_pmx_ops, + .confops = &imx1_pinconf_ops, + .owner = THIS_MODULE, +}; + +static int imx1_pinctrl_parse_groups(struct device_node *np, + struct imx1_pin_group *grp, + struct imx1_pinctrl_soc_info *info, + u32 index) +{ + int size; + const __be32 *list; + int i; + + dev_dbg(info->dev, "group(%d): %s\n", index, np->name); + + /* Initialise group */ + grp->name = np->name; + + /* + * the binding format is fsl,pins = <PIN MUX_ID CONFIG> + */ + list = of_get_property(np, "fsl,pins", &size); + /* we do not check return since it's safe node passed down */ + if (!size || size % 12) { + dev_notice(info->dev, "Not a valid fsl,pins property (%s)\n", + np->name); + return -EINVAL; + } + + grp->npins = size / 12; + grp->pins = devm_kzalloc(info->dev, + grp->npins * sizeof(struct imx1_pin), GFP_KERNEL); + grp->pin_ids = devm_kzalloc(info->dev, + grp->npins * sizeof(unsigned int), GFP_KERNEL); + + if (!grp->pins || !grp->pin_ids) + return -ENOMEM; + + for (i = 0; i < grp->npins; i++) { + grp->pins[i].pin_id = be32_to_cpu(*list++); + grp->pins[i].mux_id = be32_to_cpu(*list++); + grp->pins[i].config = be32_to_cpu(*list++); + + grp->pin_ids[i] = grp->pins[i].pin_id; + } + + return 0; +} + +static int imx1_pinctrl_parse_functions(struct device_node *np, + struct imx1_pinctrl_soc_info *info, + u32 index) +{ + struct device_node *child; + struct imx1_pmx_func *func; + struct imx1_pin_group *grp; + int ret; + static u32 grp_index; + u32 i = 0; + + dev_dbg(info->dev, "parse function(%d): %s\n", index, np->name); + + func = &info->functions[index]; + + /* Initialise function */ + func->name = np->name; + func->num_groups = of_get_child_count(np); + if (func->num_groups <= 0) + return -EINVAL; + + func->groups = devm_kzalloc(info->dev, + func->num_groups * sizeof(char *), GFP_KERNEL); + + if (!func->groups) + return -ENOMEM; + + for_each_child_of_node(np, child) { + func->groups[i] = child->name; + grp = &info->groups[grp_index++]; + ret = imx1_pinctrl_parse_groups(child, grp, info, i++); + if (ret == -ENOMEM) + return ret; + } + + return 0; +} + +static int imx1_pinctrl_parse_dt(struct platform_device *pdev, + struct imx1_pinctrl *pctl, struct imx1_pinctrl_soc_info *info) +{ + struct device_node *np = pdev->dev.of_node; + struct device_node *child; + int ret; + u32 nfuncs = 0; + u32 ngroups = 0; + u32 ifunc = 0; + + if (!np) + return -ENODEV; + + for_each_child_of_node(np, child) { + ++nfuncs; + ngroups += of_get_child_count(child); + } + + if (!nfuncs) { + dev_err(&pdev->dev, "No pin functions defined\n"); + return -EINVAL; + } + + info->nfunctions = nfuncs; + info->functions = devm_kzalloc(&pdev->dev, + nfuncs * sizeof(struct imx1_pmx_func), GFP_KERNEL); + + info->ngroups = ngroups; + info->groups = devm_kzalloc(&pdev->dev, + ngroups * sizeof(struct imx1_pin_group), GFP_KERNEL); + + + if (!info->functions || !info->groups) + return -ENOMEM; + + for_each_child_of_node(np, child) { + ret = imx1_pinctrl_parse_functions(child, info, ifunc++); + if (ret == -ENOMEM) + return -ENOMEM; + } + + return 0; +} + +int imx1_pinctrl_core_probe(struct platform_device *pdev, + struct imx1_pinctrl_soc_info *info) +{ + struct imx1_pinctrl *ipctl; + struct resource *res; + struct pinctrl_desc *pctl_desc; + int ret; + + if (!info || !info->pins || !info->npins) { + dev_err(&pdev->dev, "wrong pinctrl info\n"); + return -EINVAL; + } + info->dev = &pdev->dev; + + /* Create state holders etc for this driver */ + ipctl = devm_kzalloc(&pdev->dev, sizeof(*ipctl), GFP_KERNEL); + if (!ipctl) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) + return -ENOENT; + + ipctl->base = devm_ioremap_nocache(&pdev->dev, res->start, + resource_size(res)); + if (IS_ERR(ipctl->base)) + return PTR_ERR(ipctl->base); + + pctl_desc = &imx1_pinctrl_desc; + pctl_desc->name = dev_name(&pdev->dev); + pctl_desc->pins = info->pins; + pctl_desc->npins = info->npins; + + ret = imx1_pinctrl_parse_dt(pdev, ipctl, info); + if (ret) { + dev_err(&pdev->dev, "fail to probe dt properties\n"); + return ret; + } + + ipctl->info = info; + ipctl->dev = info->dev; + platform_set_drvdata(pdev, ipctl); + ipctl->pctl = pinctrl_register(pctl_desc, &pdev->dev, ipctl); + if (!ipctl->pctl) { + dev_err(&pdev->dev, "could not register IMX pinctrl driver\n"); + return -EINVAL; + } + + dev_info(&pdev->dev, "initialized IMX pinctrl driver\n"); + + return 0; +} + +int imx1_pinctrl_core_remove(struct platform_device *pdev) +{ + struct imx1_pinctrl *ipctl = platform_get_drvdata(pdev); + + pinctrl_unregister(ipctl->pctl); + + return 0; +} diff --git a/drivers/pinctrl/pinctrl-imx1.h b/drivers/pinctrl/pinctrl-imx1.h new file mode 100644 index 0000000..692a54c --- /dev/null +++ b/drivers/pinctrl/pinctrl-imx1.h @@ -0,0 +1,73 @@ +/* + * IMX pinmux core definitions + * + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * Copyright (C) 2012 Linaro Ltd. + * + * Author: Dong Aisheng <dong.aisheng@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __DRIVERS_PINCTRL_IMX1_H +#define __DRIVERS_PINCTRL_IMX1_H + +struct platform_device; + +/** + * struct imx1_pin - describes an IMX1/21/27 pin. + * @pin_id: ID of the described pin. + * @mux_id: ID of the mux setup. + * @config: Configuration of the pin (currently only pullup-enable). + */ +struct imx1_pin { + unsigned int pin_id; + unsigned int mux_id; + unsigned long config; +}; + +/** + * struct imx1_pin_group - describes an IMX pin group + * @name: the name of this specific pin group + * @pins: an array of imx1_pin structs used in this group + * @npins: the number of pins in this group array, i.e. the number of + * elements in .pins so we can iterate over that array + */ +struct imx1_pin_group { + const char *name; + unsigned int *pin_ids; + struct imx1_pin *pins; + unsigned npins; +}; + +/** + * struct imx1_pmx_func - describes IMX pinmux functions + * @name: the name of this specific function + * @groups: corresponding pin groups + * @num_groups: the number of groups + */ +struct imx1_pmx_func { + const char *name; + const char **groups; + unsigned num_groups; +}; + +struct imx1_pinctrl_soc_info { + struct device *dev; + const struct pinctrl_pin_desc *pins; + unsigned int npins; + struct imx1_pin_group *groups; + unsigned int ngroups; + struct imx1_pmx_func *functions; + unsigned int nfunctions; +}; + +#define IMX_PINCTRL_PIN(pin) PINCTRL_PIN(pin, #pin) + +int imx1_pinctrl_core_probe(struct platform_device *pdev, + struct imx1_pinctrl_soc_info *info); +int imx1_pinctrl_core_remove(struct platform_device *pdev); +#endif /* __DRIVERS_PINCTRL_IMX1_H */ -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v5 2/8] pinctrl: imx27: imx27 pincontrol driver 2013-10-24 15:38 [PATCH v5 0/8] ARM: imx27 pinctrl Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 1/8] pinctrl: imx1 core driver Markus Pargmann @ 2013-10-24 15:38 ` Markus Pargmann 2013-10-24 19:46 ` Matt Sealey 2013-10-24 15:38 ` [PATCH v5 3/8] ARM: dts: imx27 pin functions Markus Pargmann ` (5 subsequent siblings) 7 siblings, 1 reply; 11+ messages in thread From: Markus Pargmann @ 2013-10-24 15:38 UTC (permalink / raw) To: linux-arm-kernel imx27 pincontrol driver using the imx1 core driver. The DT bindings are similar to other imx pincontrol drivers. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Shawn Guo <shawn.guo@linaro.org> --- .../bindings/pinctrl/fsl,imx27-pinctrl.txt | 50 +++ drivers/pinctrl/Kconfig | 8 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-imx27.c | 477 +++++++++++++++++++++ 4 files changed, 536 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt create mode 100644 drivers/pinctrl/pinctrl-imx27.c diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt new file mode 100644 index 0000000..6619968 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt @@ -0,0 +1,50 @@ +* Freescale IMX27 IOMUX Controller + +Required properties: +- compatible: "fsl,imx27-iomuxc" + +The iomuxc driver node should define subnodes containing of pinctrl configuration subnodes. + +Required properties for pin configuration node: +- fsl,pins: three integers array, represents a group of pins mux and config + setting. The format is fsl,pins = <PIN MUX_ID CONFIG>. PIN and MUX_ID are + defined as macros in arch/arm/boot/dts/imx27-pinfunc.h. CONFIG can be 0 or + 1, meaning Pullup disable/enable. + PIN is a integer between 0 and 0xbf. imx27 has 6 ports with 32 configurable + configurable pins each. PIN is PORT * 32 + PORT_PIN, PORT_PIN is the pin + number on the specific port (between 0 and 31). + MUX_ID is + function + (direction << 2) + (gpio_oconf << 4) + (gpio_iconfa << 8) + (gpio_iconfb << 10) + function: 0 - Primary function + 1 - Alternate function + 2 - GPIO + direction: 0 - Input + 1 - Output + gpio_oconf: 0 - A_IN + 1 - B_IN + 2 - C_IN + 3 - Data Register + gpio_iconfa/b: 0 - GPIO_IN + 1 - Interrupt Status Register + 2 - 0 + 3 - 1 + +Example: + +iomuxc: iomuxc@10015000 { + compatible = "fsl,imx27-iomuxc"; + reg = <0x10015000 0x600>; + + uart { + pinctrl_uart1: uart-1 { + fsl,pins = < + MX27_PAD_UART1_TXD__UART1_TXD 0x0 + MX27_PAD_UART1_RXD__UART1_RXD 0x0 + MX27_PAD_UART1_CTS__UART1_CTS 0x0 + MX27_PAD_UART1_RTS__UART1_RTS 0x0 + >; + }; + + ... + }; +}; diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index 8a02aa0..4c3e5d2 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -85,6 +85,14 @@ config PINCTRL_IMX1_CORE select PINMUX select PINCONF +config PINCTRL_IMX27 + bool "IMX27 pinctrl driver" + depends on OF + depends on SOC_IMX27 + select PINCTRL_IMX1_CORE + help + Say Y here to enable the imx27 pinctrl driver + config PINCTRL_IMX35 bool "IMX35 pinctrl driver" depends on OF diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index d7caf08..5d23b71 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -19,6 +19,7 @@ obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o obj-$(CONFIG_PINCTRL_BAYTRAIL) += pinctrl-baytrail.o obj-$(CONFIG_PINCTRL_IMX) += pinctrl-imx.o obj-$(CONFIG_PINCTRL_IMX1_CORE) += pinctrl-imx1-core.o +obj-$(CONFIG_PINCTRL_IMX27) += pinctrl-imx27.o obj-$(CONFIG_PINCTRL_IMX35) += pinctrl-imx35.o obj-$(CONFIG_PINCTRL_IMX51) += pinctrl-imx51.o obj-$(CONFIG_PINCTRL_IMX53) += pinctrl-imx53.o diff --git a/drivers/pinctrl/pinctrl-imx27.c b/drivers/pinctrl/pinctrl-imx27.c new file mode 100644 index 0000000..417c992 --- /dev/null +++ b/drivers/pinctrl/pinctrl-imx27.c @@ -0,0 +1,477 @@ +/* + * imx27 pinctrl driver based on imx pinmux core + * + * Copyright (C) 2013 Pengutronix + * + * Author: Markus Pargmann <mpa@pengutronix.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/err.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/pinctrl/pinctrl.h> + +#include "pinctrl-imx1.h" + +#define PAD_ID(port, pin) (port*32 + pin) +#define PA 0 +#define PB 1 +#define PC 2 +#define PD 3 +#define PE 4 +#define PF 5 + +enum imx27_pads { + MX27_PAD_USBH2_CLK = PAD_ID(PA, 0), + MX27_PAD_USBH2_DIR = PAD_ID(PA, 1), + MX27_PAD_USBH2_DATA7 = PAD_ID(PA, 2), + MX27_PAD_USBH2_NXT = PAD_ID(PA, 3), + MX27_PAD_USBH2_STP = PAD_ID(PA, 4), + MX27_PAD_LSCLK = PAD_ID(PA, 5), + MX27_PAD_LD0 = PAD_ID(PA, 6), + MX27_PAD_LD1 = PAD_ID(PA, 7), + MX27_PAD_LD2 = PAD_ID(PA, 8), + MX27_PAD_LD3 = PAD_ID(PA, 9), + MX27_PAD_LD4 = PAD_ID(PA, 10), + MX27_PAD_LD5 = PAD_ID(PA, 11), + MX27_PAD_LD6 = PAD_ID(PA, 12), + MX27_PAD_LD7 = PAD_ID(PA, 13), + MX27_PAD_LD8 = PAD_ID(PA, 14), + MX27_PAD_LD9 = PAD_ID(PA, 15), + MX27_PAD_LD10 = PAD_ID(PA, 16), + MX27_PAD_LD11 = PAD_ID(PA, 17), + MX27_PAD_LD12 = PAD_ID(PA, 18), + MX27_PAD_LD13 = PAD_ID(PA, 19), + MX27_PAD_LD14 = PAD_ID(PA, 20), + MX27_PAD_LD15 = PAD_ID(PA, 21), + MX27_PAD_LD16 = PAD_ID(PA, 22), + MX27_PAD_LD17 = PAD_ID(PA, 23), + MX27_PAD_REV = PAD_ID(PA, 24), + MX27_PAD_CLS = PAD_ID(PA, 25), + MX27_PAD_PS = PAD_ID(PA, 26), + MX27_PAD_SPL_SPR = PAD_ID(PA, 27), + MX27_PAD_HSYNC = PAD_ID(PA, 28), + MX27_PAD_VSYNC = PAD_ID(PA, 29), + MX27_PAD_CONTRAST = PAD_ID(PA, 30), + MX27_PAD_OE_ACD = PAD_ID(PA, 31), + + MX27_PAD_UNUSED0 = PAD_ID(PB, 0), + MX27_PAD_UNUSED1 = PAD_ID(PB, 1), + MX27_PAD_UNUSED2 = PAD_ID(PB, 2), + MX27_PAD_UNUSED3 = PAD_ID(PB, 3), + MX27_PAD_SD2_D0 = PAD_ID(PB, 4), + MX27_PAD_SD2_D1 = PAD_ID(PB, 5), + MX27_PAD_SD2_D2 = PAD_ID(PB, 6), + MX27_PAD_SD2_D3 = PAD_ID(PB, 7), + MX27_PAD_SD2_CMD = PAD_ID(PB, 8), + MX27_PAD_SD2_CLK = PAD_ID(PB, 9), + MX27_PAD_CSI_D0 = PAD_ID(PB, 10), + MX27_PAD_CSI_D1 = PAD_ID(PB, 11), + MX27_PAD_CSI_D2 = PAD_ID(PB, 12), + MX27_PAD_CSI_D3 = PAD_ID(PB, 13), + MX27_PAD_CSI_D4 = PAD_ID(PB, 14), + MX27_PAD_CSI_MCLK = PAD_ID(PB, 15), + MX27_PAD_CSI_PIXCLK = PAD_ID(PB, 16), + MX27_PAD_CSI_D5 = PAD_ID(PB, 17), + MX27_PAD_CSI_D6 = PAD_ID(PB, 18), + MX27_PAD_CSI_D7 = PAD_ID(PB, 19), + MX27_PAD_CSI_VSYNC = PAD_ID(PB, 20), + MX27_PAD_CSI_HSYNC = PAD_ID(PB, 21), + MX27_PAD_USBH1_SUSP = PAD_ID(PB, 22), + MX27_PAD_USB_PWR = PAD_ID(PB, 23), + MX27_PAD_USB_OC_B = PAD_ID(PB, 24), + MX27_PAD_USBH1_RCV = PAD_ID(PB, 25), + MX27_PAD_USBH1_FS = PAD_ID(PB, 26), + MX27_PAD_USBH1_OE_B = PAD_ID(PB, 27), + MX27_PAD_USBH1_TXDM = PAD_ID(PB, 28), + MX27_PAD_USBH1_TXDP = PAD_ID(PB, 29), + MX27_PAD_USBH1_RXDM = PAD_ID(PB, 30), + MX27_PAD_USBH1_RXDP = PAD_ID(PB, 31), + + MX27_PAD_UNUSED4 = PAD_ID(PC, 0), + MX27_PAD_UNUSED5 = PAD_ID(PC, 1), + MX27_PAD_UNUSED6 = PAD_ID(PC, 2), + MX27_PAD_UNUSED7 = PAD_ID(PC, 3), + MX27_PAD_UNUSED8 = PAD_ID(PC, 4), + MX27_PAD_I2C2_SDA = PAD_ID(PC, 5), + MX27_PAD_I2C2_SCL = PAD_ID(PC, 6), + MX27_PAD_USBOTG_DATA5 = PAD_ID(PC, 7), + MX27_PAD_USBOTG_DATA6 = PAD_ID(PC, 8), + MX27_PAD_USBOTG_DATA0 = PAD_ID(PC, 9), + MX27_PAD_USBOTG_DATA2 = PAD_ID(PC, 10), + MX27_PAD_USBOTG_DATA1 = PAD_ID(PC, 11), + MX27_PAD_USBOTG_DATA4 = PAD_ID(PC, 12), + MX27_PAD_USBOTG_DATA3 = PAD_ID(PC, 13), + MX27_PAD_TOUT = PAD_ID(PC, 14), + MX27_PAD_TIN = PAD_ID(PC, 15), + MX27_PAD_SSI4_FS = PAD_ID(PC, 16), + MX27_PAD_SSI4_RXDAT = PAD_ID(PC, 17), + MX27_PAD_SSI4_TXDAT = PAD_ID(PC, 18), + MX27_PAD_SSI4_CLK = PAD_ID(PC, 19), + MX27_PAD_SSI1_FS = PAD_ID(PC, 20), + MX27_PAD_SSI1_RXDAT = PAD_ID(PC, 21), + MX27_PAD_SSI1_TXDAT = PAD_ID(PC, 22), + MX27_PAD_SSI1_CLK = PAD_ID(PC, 23), + MX27_PAD_SSI2_FS = PAD_ID(PC, 24), + MX27_PAD_SSI2_RXDAT = PAD_ID(PC, 25), + MX27_PAD_SSI2_TXDAT = PAD_ID(PC, 26), + MX27_PAD_SSI2_CLK = PAD_ID(PC, 27), + MX27_PAD_SSI3_FS = PAD_ID(PC, 28), + MX27_PAD_SSI3_RXDAT = PAD_ID(PC, 29), + MX27_PAD_SSI3_TXDAT = PAD_ID(PC, 30), + MX27_PAD_SSI3_CLK = PAD_ID(PC, 31), + + MX27_PAD_SD3_CMD = PAD_ID(PD, 0), + MX27_PAD_SD3_CLK = PAD_ID(PD, 1), + MX27_PAD_ATA_DATA0 = PAD_ID(PD, 2), + MX27_PAD_ATA_DATA1 = PAD_ID(PD, 3), + MX27_PAD_ATA_DATA2 = PAD_ID(PD, 4), + MX27_PAD_ATA_DATA3 = PAD_ID(PD, 5), + MX27_PAD_ATA_DATA4 = PAD_ID(PD, 6), + MX27_PAD_ATA_DATA5 = PAD_ID(PD, 7), + MX27_PAD_ATA_DATA6 = PAD_ID(PD, 8), + MX27_PAD_ATA_DATA7 = PAD_ID(PD, 9), + MX27_PAD_ATA_DATA8 = PAD_ID(PD, 10), + MX27_PAD_ATA_DATA9 = PAD_ID(PD, 11), + MX27_PAD_ATA_DATA10 = PAD_ID(PD, 12), + MX27_PAD_ATA_DATA11 = PAD_ID(PD, 13), + MX27_PAD_ATA_DATA12 = PAD_ID(PD, 14), + MX27_PAD_ATA_DATA13 = PAD_ID(PD, 15), + MX27_PAD_ATA_DATA14 = PAD_ID(PD, 16), + MX27_PAD_I2C_DATA = PAD_ID(PD, 17), + MX27_PAD_I2C_CLK = PAD_ID(PD, 18), + MX27_PAD_CSPI2_SS2 = PAD_ID(PD, 19), + MX27_PAD_CSPI2_SS1 = PAD_ID(PD, 20), + MX27_PAD_CSPI2_SS0 = PAD_ID(PD, 21), + MX27_PAD_CSPI2_SCLK = PAD_ID(PD, 22), + MX27_PAD_CSPI2_MISO = PAD_ID(PD, 23), + MX27_PAD_CSPI2_MOSI = PAD_ID(PD, 24), + MX27_PAD_CSPI1_RDY = PAD_ID(PD, 25), + MX27_PAD_CSPI1_SS2 = PAD_ID(PD, 26), + MX27_PAD_CSPI1_SS1 = PAD_ID(PD, 27), + MX27_PAD_CSPI1_SS0 = PAD_ID(PD, 28), + MX27_PAD_CSPI1_SCLK = PAD_ID(PD, 29), + MX27_PAD_CSPI1_MISO = PAD_ID(PD, 30), + MX27_PAD_CSPI1_MOSI = PAD_ID(PD, 31), + + MX27_PAD_USBOTG_NXT = PAD_ID(PE, 0), + MX27_PAD_USBOTG_STP = PAD_ID(PE, 1), + MX27_PAD_USBOTG_DIR = PAD_ID(PE, 2), + MX27_PAD_UART2_CTS = PAD_ID(PE, 3), + MX27_PAD_UART2_RTS = PAD_ID(PE, 4), + MX27_PAD_PWMO = PAD_ID(PE, 5), + MX27_PAD_UART2_TXD = PAD_ID(PE, 6), + MX27_PAD_UART2_RXD = PAD_ID(PE, 7), + MX27_PAD_UART3_TXD = PAD_ID(PE, 8), + MX27_PAD_UART3_RXD = PAD_ID(PE, 9), + MX27_PAD_UART3_CTS = PAD_ID(PE, 10), + MX27_PAD_UART3_RTS = PAD_ID(PE, 11), + MX27_PAD_UART1_TXD = PAD_ID(PE, 12), + MX27_PAD_UART1_RXD = PAD_ID(PE, 13), + MX27_PAD_UART1_CTS = PAD_ID(PE, 14), + MX27_PAD_UART1_RTS = PAD_ID(PE, 15), + MX27_PAD_RTCK = PAD_ID(PE, 16), + MX27_PAD_RESET_OUT_B = PAD_ID(PE, 17), + MX27_PAD_SD1_D0 = PAD_ID(PE, 18), + MX27_PAD_SD1_D1 = PAD_ID(PE, 19), + MX27_PAD_SD1_D2 = PAD_ID(PE, 20), + MX27_PAD_SD1_D3 = PAD_ID(PE, 21), + MX27_PAD_SD1_CMD = PAD_ID(PE, 22), + MX27_PAD_SD1_CLK = PAD_ID(PE, 23), + MX27_PAD_USBOTG_CLK = PAD_ID(PE, 24), + MX27_PAD_USBOTG_DATA7 = PAD_ID(PE, 25), + MX27_PAD_UNUSED9 = PAD_ID(PE, 26), + MX27_PAD_UNUSED10 = PAD_ID(PE, 27), + MX27_PAD_UNUSED11 = PAD_ID(PE, 28), + MX27_PAD_UNUSED12 = PAD_ID(PE, 29), + MX27_PAD_UNUSED13 = PAD_ID(PE, 30), + MX27_PAD_UNUSED14 = PAD_ID(PE, 31), + + MX27_PAD_NFRB = PAD_ID(PF, 0), + MX27_PAD_NFCLE = PAD_ID(PF, 1), + MX27_PAD_NFWP_B = PAD_ID(PF, 2), + MX27_PAD_NFCE_B = PAD_ID(PF, 3), + MX27_PAD_NFALE = PAD_ID(PF, 4), + MX27_PAD_NFRE_B = PAD_ID(PF, 5), + MX27_PAD_NFWE_B = PAD_ID(PF, 6), + MX27_PAD_PC_POE = PAD_ID(PF, 7), + MX27_PAD_PC_RW_B = PAD_ID(PF, 8), + MX27_PAD_IOIS16 = PAD_ID(PF, 9), + MX27_PAD_PC_RST = PAD_ID(PF, 10), + MX27_PAD_PC_BVD2 = PAD_ID(PF, 11), + MX27_PAD_PC_BVD1 = PAD_ID(PF, 12), + MX27_PAD_PC_VS2 = PAD_ID(PF, 13), + MX27_PAD_PC_VS1 = PAD_ID(PF, 14), + MX27_PAD_CLKO = PAD_ID(PF, 15), + MX27_PAD_PC_PWRON = PAD_ID(PF, 16), + MX27_PAD_PC_READY = PAD_ID(PF, 17), + MX27_PAD_PC_WAIT_B = PAD_ID(PF, 18), + MX27_PAD_PC_CD2_B = PAD_ID(PF, 19), + MX27_PAD_PC_CD1_B = PAD_ID(PF, 20), + MX27_PAD_CS4_B = PAD_ID(PF, 21), + MX27_PAD_CS5_B = PAD_ID(PF, 22), + MX27_PAD_ATA_DATA15 = PAD_ID(PF, 23), + MX27_PAD_UNUSED15 = PAD_ID(PF, 24), + MX27_PAD_UNUSED16 = PAD_ID(PF, 25), + MX27_PAD_UNUSED17 = PAD_ID(PF, 26), + MX27_PAD_UNUSED18 = PAD_ID(PF, 27), + MX27_PAD_UNUSED19 = PAD_ID(PF, 28), + MX27_PAD_UNUSED20 = PAD_ID(PF, 29), + MX27_PAD_UNUSED21 = PAD_ID(PF, 30), + MX27_PAD_UNUSED22 = PAD_ID(PF, 31), +}; + +/* Pad names for the pinmux subsystem */ +static const struct pinctrl_pin_desc imx27_pinctrl_pads[] = { + IMX_PINCTRL_PIN(MX27_PAD_USBH2_CLK), + IMX_PINCTRL_PIN(MX27_PAD_USBH2_DIR), + IMX_PINCTRL_PIN(MX27_PAD_USBH2_DATA7), + IMX_PINCTRL_PIN(MX27_PAD_USBH2_NXT), + IMX_PINCTRL_PIN(MX27_PAD_USBH2_STP), + IMX_PINCTRL_PIN(MX27_PAD_LSCLK), + IMX_PINCTRL_PIN(MX27_PAD_LD0), + IMX_PINCTRL_PIN(MX27_PAD_LD1), + IMX_PINCTRL_PIN(MX27_PAD_LD2), + IMX_PINCTRL_PIN(MX27_PAD_LD3), + IMX_PINCTRL_PIN(MX27_PAD_LD4), + IMX_PINCTRL_PIN(MX27_PAD_LD5), + IMX_PINCTRL_PIN(MX27_PAD_LD6), + IMX_PINCTRL_PIN(MX27_PAD_LD7), + IMX_PINCTRL_PIN(MX27_PAD_LD8), + IMX_PINCTRL_PIN(MX27_PAD_LD9), + IMX_PINCTRL_PIN(MX27_PAD_LD10), + IMX_PINCTRL_PIN(MX27_PAD_LD11), + IMX_PINCTRL_PIN(MX27_PAD_LD12), + IMX_PINCTRL_PIN(MX27_PAD_LD13), + IMX_PINCTRL_PIN(MX27_PAD_LD14), + IMX_PINCTRL_PIN(MX27_PAD_LD15), + IMX_PINCTRL_PIN(MX27_PAD_LD16), + IMX_PINCTRL_PIN(MX27_PAD_LD17), + IMX_PINCTRL_PIN(MX27_PAD_REV), + IMX_PINCTRL_PIN(MX27_PAD_CLS), + IMX_PINCTRL_PIN(MX27_PAD_PS), + IMX_PINCTRL_PIN(MX27_PAD_SPL_SPR), + IMX_PINCTRL_PIN(MX27_PAD_HSYNC), + IMX_PINCTRL_PIN(MX27_PAD_VSYNC), + IMX_PINCTRL_PIN(MX27_PAD_CONTRAST), + IMX_PINCTRL_PIN(MX27_PAD_OE_ACD), + + IMX_PINCTRL_PIN(MX27_PAD_UNUSED0), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED1), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED2), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED3), + IMX_PINCTRL_PIN(MX27_PAD_SD2_D0), + IMX_PINCTRL_PIN(MX27_PAD_SD2_D1), + IMX_PINCTRL_PIN(MX27_PAD_SD2_D2), + IMX_PINCTRL_PIN(MX27_PAD_SD2_D3), + IMX_PINCTRL_PIN(MX27_PAD_SD2_CMD), + IMX_PINCTRL_PIN(MX27_PAD_SD2_CLK), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D0), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D1), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D2), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D3), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D4), + IMX_PINCTRL_PIN(MX27_PAD_CSI_MCLK), + IMX_PINCTRL_PIN(MX27_PAD_CSI_PIXCLK), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D5), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D6), + IMX_PINCTRL_PIN(MX27_PAD_CSI_D7), + IMX_PINCTRL_PIN(MX27_PAD_CSI_VSYNC), + IMX_PINCTRL_PIN(MX27_PAD_CSI_HSYNC), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_SUSP), + IMX_PINCTRL_PIN(MX27_PAD_USB_PWR), + IMX_PINCTRL_PIN(MX27_PAD_USB_OC_B), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_RCV), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_FS), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_OE_B), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_TXDM), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_TXDP), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_RXDM), + IMX_PINCTRL_PIN(MX27_PAD_USBH1_RXDP), + + IMX_PINCTRL_PIN(MX27_PAD_UNUSED4), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED5), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED6), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED7), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED8), + IMX_PINCTRL_PIN(MX27_PAD_I2C2_SDA), + IMX_PINCTRL_PIN(MX27_PAD_I2C2_SCL), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA5), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA6), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA0), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA2), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA1), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA4), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA3), + IMX_PINCTRL_PIN(MX27_PAD_TOUT), + IMX_PINCTRL_PIN(MX27_PAD_TIN), + IMX_PINCTRL_PIN(MX27_PAD_SSI4_FS), + IMX_PINCTRL_PIN(MX27_PAD_SSI4_RXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI4_TXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI4_CLK), + IMX_PINCTRL_PIN(MX27_PAD_SSI1_FS), + IMX_PINCTRL_PIN(MX27_PAD_SSI1_RXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI1_TXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI1_CLK), + IMX_PINCTRL_PIN(MX27_PAD_SSI2_FS), + IMX_PINCTRL_PIN(MX27_PAD_SSI2_RXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI2_TXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI2_CLK), + IMX_PINCTRL_PIN(MX27_PAD_SSI3_FS), + IMX_PINCTRL_PIN(MX27_PAD_SSI3_RXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI3_TXDAT), + IMX_PINCTRL_PIN(MX27_PAD_SSI3_CLK), + + IMX_PINCTRL_PIN(MX27_PAD_SD3_CMD), + IMX_PINCTRL_PIN(MX27_PAD_SD3_CLK), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA0), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA1), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA2), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA3), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA4), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA5), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA6), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA7), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA8), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA9), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA10), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA11), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA12), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA13), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA14), + IMX_PINCTRL_PIN(MX27_PAD_I2C_DATA), + IMX_PINCTRL_PIN(MX27_PAD_I2C_CLK), + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_SS2), + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_SS1), + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_SS0), + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_SCLK), + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_MISO), + IMX_PINCTRL_PIN(MX27_PAD_CSPI2_MOSI), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_RDY), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_SS2), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_SS1), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_SS0), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_SCLK), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_MISO), + IMX_PINCTRL_PIN(MX27_PAD_CSPI1_MOSI), + + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_NXT), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_STP), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DIR), + IMX_PINCTRL_PIN(MX27_PAD_UART2_CTS), + IMX_PINCTRL_PIN(MX27_PAD_UART2_RTS), + IMX_PINCTRL_PIN(MX27_PAD_PWMO), + IMX_PINCTRL_PIN(MX27_PAD_UART2_TXD), + IMX_PINCTRL_PIN(MX27_PAD_UART2_RXD), + IMX_PINCTRL_PIN(MX27_PAD_UART3_TXD), + IMX_PINCTRL_PIN(MX27_PAD_UART3_RXD), + IMX_PINCTRL_PIN(MX27_PAD_UART3_CTS), + IMX_PINCTRL_PIN(MX27_PAD_UART3_RTS), + IMX_PINCTRL_PIN(MX27_PAD_UART1_TXD), + IMX_PINCTRL_PIN(MX27_PAD_UART1_RXD), + IMX_PINCTRL_PIN(MX27_PAD_UART1_CTS), + IMX_PINCTRL_PIN(MX27_PAD_UART1_RTS), + IMX_PINCTRL_PIN(MX27_PAD_RTCK), + IMX_PINCTRL_PIN(MX27_PAD_RESET_OUT_B), + IMX_PINCTRL_PIN(MX27_PAD_SD1_D0), + IMX_PINCTRL_PIN(MX27_PAD_SD1_D1), + IMX_PINCTRL_PIN(MX27_PAD_SD1_D2), + IMX_PINCTRL_PIN(MX27_PAD_SD1_D3), + IMX_PINCTRL_PIN(MX27_PAD_SD1_CMD), + IMX_PINCTRL_PIN(MX27_PAD_SD1_CLK), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_CLK), + IMX_PINCTRL_PIN(MX27_PAD_USBOTG_DATA7), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED9), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED10), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED11), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED12), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED13), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED14), + + IMX_PINCTRL_PIN(MX27_PAD_NFRB), + IMX_PINCTRL_PIN(MX27_PAD_NFCLE), + IMX_PINCTRL_PIN(MX27_PAD_NFWP_B), + IMX_PINCTRL_PIN(MX27_PAD_NFCE_B), + IMX_PINCTRL_PIN(MX27_PAD_NFALE), + IMX_PINCTRL_PIN(MX27_PAD_NFRE_B), + IMX_PINCTRL_PIN(MX27_PAD_NFWE_B), + IMX_PINCTRL_PIN(MX27_PAD_PC_POE), + IMX_PINCTRL_PIN(MX27_PAD_PC_RW_B), + IMX_PINCTRL_PIN(MX27_PAD_IOIS16), + IMX_PINCTRL_PIN(MX27_PAD_PC_RST), + IMX_PINCTRL_PIN(MX27_PAD_PC_BVD2), + IMX_PINCTRL_PIN(MX27_PAD_PC_BVD1), + IMX_PINCTRL_PIN(MX27_PAD_PC_VS2), + IMX_PINCTRL_PIN(MX27_PAD_PC_VS1), + IMX_PINCTRL_PIN(MX27_PAD_CLKO), + IMX_PINCTRL_PIN(MX27_PAD_PC_PWRON), + IMX_PINCTRL_PIN(MX27_PAD_PC_READY), + IMX_PINCTRL_PIN(MX27_PAD_PC_WAIT_B), + IMX_PINCTRL_PIN(MX27_PAD_PC_CD2_B), + IMX_PINCTRL_PIN(MX27_PAD_PC_CD1_B), + IMX_PINCTRL_PIN(MX27_PAD_CS4_B), + IMX_PINCTRL_PIN(MX27_PAD_CS5_B), + IMX_PINCTRL_PIN(MX27_PAD_ATA_DATA15), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED15), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED16), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED17), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED18), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED19), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED20), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED21), + IMX_PINCTRL_PIN(MX27_PAD_UNUSED22), +}; + +static struct imx1_pinctrl_soc_info imx27_pinctrl_info = { + .pins = imx27_pinctrl_pads, + .npins = ARRAY_SIZE(imx27_pinctrl_pads), +}; + +static struct of_device_id imx27_pinctrl_of_match[] = { + { .compatible = "fsl,imx27-iomuxc", }, + { /* sentinel */ } +}; + +struct imx27_pinctrl_private { + int num_gpio_childs; + struct platform_device **gpio_dev; + struct mxc_gpio_platform_data *gpio_pdata; +}; + +static int imx27_pinctrl_probe(struct platform_device *pdev) +{ + return imx1_pinctrl_core_probe(pdev, &imx27_pinctrl_info); +} + +static struct platform_driver imx27_pinctrl_driver = { + .driver = { + .name = "imx27-pinctrl", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(imx27_pinctrl_of_match), + }, + .probe = imx27_pinctrl_probe, + .remove = imx1_pinctrl_core_remove, +}; + +static int __init imx27_pinctrl_init(void) +{ + return platform_driver_register(&imx27_pinctrl_driver); +} +arch_initcall(imx27_pinctrl_init); + +static void __exit imx27_pinctrl_exit(void) +{ + platform_driver_unregister(&imx27_pinctrl_driver); +} +module_exit(imx27_pinctrl_exit); +MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>"); +MODULE_DESCRIPTION("Freescale IMX27 pinctrl driver"); +MODULE_LICENSE("GPL v2"); -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v5 2/8] pinctrl: imx27: imx27 pincontrol driver 2013-10-24 15:38 ` [PATCH v5 2/8] pinctrl: imx27: imx27 pincontrol driver Markus Pargmann @ 2013-10-24 19:46 ` Matt Sealey 2013-10-28 7:57 ` Markus Pargmann 0 siblings, 1 reply; 11+ messages in thread From: Matt Sealey @ 2013-10-24 19:46 UTC (permalink / raw) To: linux-arm-kernel On Thu, Oct 24, 2013 at 10:38 AM, Markus Pargmann <mpa@pengutronix.de> wrote: > imx27 pincontrol driver using the imx1 core driver. The DT bindings are > similar to other imx pincontrol drivers. > > Signed-off-by: Markus Pargmann <mpa@pengutronix.de> > Acked-by: Sascha Hauer <s.hauer@pengutronix.de> > Acked-by: Shawn Guo <shawn.guo@linaro.org> > --- > .../bindings/pinctrl/fsl,imx27-pinctrl.txt | 50 +++ > drivers/pinctrl/Kconfig | 8 + > drivers/pinctrl/Makefile | 1 + > drivers/pinctrl/pinctrl-imx27.c | 477 +++++++++++++++++++++ > 4 files changed, 536 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt > create mode 100644 drivers/pinctrl/pinctrl-imx27.c > > diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt > new file mode 100644 > index 0000000..6619968 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt > @@ -0,0 +1,50 @@ > +* Freescale IMX27 IOMUX Controller > + > +Required properties: > +- compatible: "fsl,imx27-iomuxc" > + > +The iomuxc driver node should define subnodes containing of pinctrl configuration subnodes. > + > +Required properties for pin configuration node: > +- fsl,pins: three integers array, represents a group of pins mux and config > + setting. The format is fsl,pins = <PIN MUX_ID CONFIG>. PIN and MUX_ID are > + defined as macros in arch/arm/boot/dts/imx27-pinfunc.h. CONFIG can be 0 or Can we get away from this concept that a binding is predicated on the fact that they're preprocessed? You're getting it half right.. as below. Binding descriptions must NOT rely on preprocessing helpers, for the following reasons * Device trees could be generated by methods other than preprocessed source * Device trees could be generated by Linux builds and passed to other operating systems (therefore they need to know the definition in reality). Please provide and describe the RAW data format of the property and then somewhere afterwards mention that as a convenience there are preprocessor macros which make life easier. You can also mention the include name, but the path (arch/arm/boot/dts) may not be fixed. This may not even be Linux. They may be split elsewhere in a separate tree that has no OS and therefore a different layout. Bindings should be OS agnostic - certainly source code location agnostic - where possible. > + PIN is a integer between 0 and 0xbf Correct. > imx27 has 6 ports with 32 configurable > + configurable pins each. PIN is PORT * 32 + PORT_PIN, PORT_PIN is the pin > + number on the specific port (between 0 and 31). Correct. > + MUX_ID is > + function + (direction << 2) + (gpio_oconf << 4) + (gpio_iconfa << 8) + (gpio_iconfb << 10) > + function: 0 - Primary function > + 1 - Alternate function > + 2 - GPIO > + direction: 0 - Input > + 1 - Output > + gpio_oconf: 0 - A_IN > + 1 - B_IN > + 2 - C_IN > + 3 - Data Register > + gpio_iconfa/b: 0 - GPIO_IN > + 1 - Interrupt Status Register > + 2 - 0 > + 3 - 1 Correct, but I don't like mixing register values for multiple registers in a single field. I guess you'd waste a ton of space any other way, so acceptable. If they're the bits for a single register (could be, but I don't have access to an i.MX27 manual right now) then just describe it as the content of the register as defined in a location in the manual, you won't need to re-describe what is already in the manual. > +Example: > + > +iomuxc: iomuxc at 10015000 { > + compatible = "fsl,imx27-iomuxc"; > + reg = <0x10015000 0x600>; > + > + uart { > + pinctrl_uart1: uart-1 { > + fsl,pins = < > + MX27_PAD_UART1_TXD__UART1_TXD 0x0 Incorrect. Your example should show the raw output. Try compiling this and then performing the following: scripts/dtc/dtc -I dtb -O dts imx27-my-platform.dtb The place where pinctrl_uart1 is in that output is your example. Lots of awful, unreadable numbers. However you may provide a second example explaining the convenience of using the preprocessor macros exactly as above, perhaps with the location of the preprocessor macros include. > + MX27_PAD_UART1_RXD__UART1_RXD 0x0 One question; are these definitions the one in the manual (for the names etc, in the huge enums later, especially?) or stripped from existing source code? Bindings - and their preprocessor helper macros - should follow the latest manual if they can. There are many odd differences in i.MX6 pinctrl, but for instance if the manual describes it as SD_DAT3 with function SD_DATA3 then it should be SD_DAT3__SD_DATA3 rather than SD_DAT3__SD_DAT3 (even if the SD Association spec says DAT3, since you are describing an i.MX27 mux, not the SD physical layer :). That way the preprocessor definitions can be searched for in the manual with some mangling, and searched for in the headers by pasting out the function name or the original pin name. If they differ, then someone has to resolve the differences with their brain which is more work for the reader. Thanks, Matt Sealey <neko@bakuhatsu.net> ^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v5 2/8] pinctrl: imx27: imx27 pincontrol driver 2013-10-24 19:46 ` Matt Sealey @ 2013-10-28 7:57 ` Markus Pargmann 0 siblings, 0 replies; 11+ messages in thread From: Markus Pargmann @ 2013-10-28 7:57 UTC (permalink / raw) To: linux-arm-kernel Hi, On Thu, Oct 24, 2013 at 02:46:58PM -0500, Matt Sealey wrote: > On Thu, Oct 24, 2013 at 10:38 AM, Markus Pargmann <mpa@pengutronix.de> wrote: > > imx27 pincontrol driver using the imx1 core driver. The DT bindings are > > similar to other imx pincontrol drivers. > > > > Signed-off-by: Markus Pargmann <mpa@pengutronix.de> > > Acked-by: Sascha Hauer <s.hauer@pengutronix.de> > > Acked-by: Shawn Guo <shawn.guo@linaro.org> > > --- > > .../bindings/pinctrl/fsl,imx27-pinctrl.txt | 50 +++ > > drivers/pinctrl/Kconfig | 8 + > > drivers/pinctrl/Makefile | 1 + > > drivers/pinctrl/pinctrl-imx27.c | 477 +++++++++++++++++++++ > > 4 files changed, 536 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt > > create mode 100644 drivers/pinctrl/pinctrl-imx27.c > > > > diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt > > new file mode 100644 > > index 0000000..6619968 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt > > @@ -0,0 +1,50 @@ > > +* Freescale IMX27 IOMUX Controller > > + > > +Required properties: > > +- compatible: "fsl,imx27-iomuxc" > > + > > +The iomuxc driver node should define subnodes containing of pinctrl configuration subnodes. > > + > > +Required properties for pin configuration node: > > +- fsl,pins: three integers array, represents a group of pins mux and config > > + setting. The format is fsl,pins = <PIN MUX_ID CONFIG>. PIN and MUX_ID are > > + defined as macros in arch/arm/boot/dts/imx27-pinfunc.h. CONFIG can be 0 or > > Can we get away from this concept that a binding is predicated on the > fact that they're preprocessed? You're getting it half right.. as > below. > > Binding descriptions must NOT rely on preprocessing helpers, for the > following reasons > > * Device trees could be generated by methods other than preprocessed source > * Device trees could be generated by Linux builds and passed to other > operating systems (therefore they need to know the definition in > reality). > > Please provide and describe the RAW data format of the property and > then somewhere afterwards mention that as a convenience there are > preprocessor macros which make life easier. You can also mention the > include name, but the path (arch/arm/boot/dts) may not be fixed. This > may not even be Linux. They may be split elsewhere in a separate tree > that has no OS and therefore a different layout. Bindings should be OS > agnostic - certainly source code location agnostic - where possible. > > > + PIN is a integer between 0 and 0xbf > > Correct. > > > imx27 has 6 ports with 32 configurable > > + configurable pins each. PIN is PORT * 32 + PORT_PIN, PORT_PIN is the pin > > + number on the specific port (between 0 and 31). > > Correct. > > > + MUX_ID is > > + function + (direction << 2) + (gpio_oconf << 4) + (gpio_iconfa << 8) + (gpio_iconfb << 10) > > + function: 0 - Primary function > > + 1 - Alternate function > > + 2 - GPIO > > + direction: 0 - Input > > + 1 - Output > > + gpio_oconf: 0 - A_IN > > + 1 - B_IN > > + 2 - C_IN > > + 3 - Data Register > > + gpio_iconfa/b: 0 - GPIO_IN > > + 1 - Interrupt Status Register > > + 2 - 0 > > + 3 - 1 > > Correct, but I don't like mixing register values for multiple > registers in a single field. I guess you'd waste a ton of space any > other way, so acceptable. > > If they're the bits for a single register (could be, but I don't have > access to an i.MX27 manual right now) then just describe it as the > content of the register as defined in a location in the manual, you > won't need to re-describe what is already in the manual. Unfortunately it is not the content of a single register. It is spreaded across multiple registers each one containing the configuration of all pins of one port. The above described parts are nearly identical to the real registers. "direction", "gpio_oconf" and "gpio_iconfa/b" exist as registers. "function" is describing two registers, "GIUS" (GPIO in use) and "GPR" (General Purpose Register). function is (GIUS << 1) + GPR. I will add the registernames to the documentation. > > > +Example: > > + > > +iomuxc: iomuxc at 10015000 { > > + compatible = "fsl,imx27-iomuxc"; > > + reg = <0x10015000 0x600>; > > + > > + uart { > > + pinctrl_uart1: uart-1 { > > + fsl,pins = < > > + MX27_PAD_UART1_TXD__UART1_TXD 0x0 > > Incorrect. > > Your example should show the raw output. Try compiling this and then > performing the following: > > scripts/dtc/dtc -I dtb -O dts imx27-my-platform.dtb > > The place where pinctrl_uart1 is in that output is your example. Lots > of awful, unreadable numbers. > > However you may provide a second example explaining the convenience of > using the preprocessor macros exactly as above, perhaps with the > location of the preprocessor macros include. Okay, I will change the example and add some documentation about the macros at the end of the document. > > > + MX27_PAD_UART1_RXD__UART1_RXD 0x0 > > One question; are these definitions the one in the manual (for the > names etc, in the huge enums later, especially?) or stripped from > existing source code? The definitions are from the manual MX27_PAD_<Pad name>__<Signal name> Thanks, Markus Pargmann > > Bindings - and their preprocessor helper macros - should follow the > latest manual if they can. There are many odd differences in i.MX6 > pinctrl, but for instance if the manual describes it as SD_DAT3 with > function SD_DATA3 then it should be SD_DAT3__SD_DATA3 rather than > SD_DAT3__SD_DAT3 (even if the SD Association spec says DAT3, since you > are describing an i.MX27 mux, not the SD physical layer :). That way > the preprocessor definitions can be searched for in the manual with > some mangling, and searched for in the headers by pasting out the > function name or the original pin name. If they differ, then someone > has to resolve the differences with their brain which is more work for > the reader. > > Thanks, > Matt Sealey <neko@bakuhatsu.net> > -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | ^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v5 3/8] ARM: dts: imx27 pin functions 2013-10-24 15:38 [PATCH v5 0/8] ARM: imx27 pinctrl Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 1/8] pinctrl: imx1 core driver Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 2/8] pinctrl: imx27: imx27 pincontrol driver Markus Pargmann @ 2013-10-24 15:38 ` Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 4/8] ARM: dts: imx27 pinctrl Markus Pargmann ` (4 subsequent siblings) 7 siblings, 0 replies; 11+ messages in thread From: Markus Pargmann @ 2013-10-24 15:38 UTC (permalink / raw) To: linux-arm-kernel Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> --- arch/arm/boot/dts/imx27-pinfunc.h | 524 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 524 insertions(+) create mode 100644 arch/arm/boot/dts/imx27-pinfunc.h diff --git a/arch/arm/boot/dts/imx27-pinfunc.h b/arch/arm/boot/dts/imx27-pinfunc.h new file mode 100644 index 0000000..32bfcc2 --- /dev/null +++ b/arch/arm/boot/dts/imx27-pinfunc.h @@ -0,0 +1,524 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef __DTS_IMX27_PINFUNC_H +#define __DTS_IMX27_PINFUNC_H + +/* + * The pin function ID is a tuple of + * <pin mux_id> + * mux_id consists of + * function + (direction << 2) + (gpio_oconf << 4) + (gpio_iconfa << 8) + (gpio_iconfb << 10) + * + * function: 0 - Primary function + * 1 - Alternate function + * 2 - GPIO + * direction: 0 - Input + * 1 - Output + * gpio_oconf: 0 - A_IN + * 1 - B_IN + * 2 - C_IN + * 3 - Data Register + * gpio_iconfa/b: 0 - GPIO_IN + * 1 - Interrupt Status Register + * 2 - 0 + * 3 - 1 + * + * 'pin' is an integer between 0 and 0xbf. imx27 has 6 ports with 32 configurable + * configurable pins each. 'pin' is PORT * 32 + PORT_PIN, PORT_PIN is the pin + * number on the specific port (between 0 and 31). + */ + +#define MX27_PAD_USBH2_CLK__USBH2_CLK 0x00 0x000 +#define MX27_PAD_USBH2_CLK__GPIO1_0 0x00 0x036 +#define MX27_PAD_USBH2_DIR__USBH2_DIR 0x01 0x000 +#define MX27_PAD_USBH2_DIR__GPIO1_1 0x01 0x036 +#define MX27_PAD_USBH2_DATA7__USBH2_DATA7 0x02 0x004 +#define MX27_PAD_USBH2_DATA7__GPIO1_2 0x02 0x036 +#define MX27_PAD_USBH2_NXT__USBH2_NXT 0x03 0x000 +#define MX27_PAD_USBH2_NXT__GPIO1_3 0x03 0x036 +#define MX27_PAD_USBH2_STP__USBH2_STP 0x04 0x004 +#define MX27_PAD_USBH2_STP__GPIO1_4 0x04 0x036 +#define MX27_PAD_LSCLK__LSCLK 0x05 0x004 +#define MX27_PAD_LSCLK__GPIO1_5 0x05 0x036 +#define MX27_PAD_LD0__LD0 0x06 0x004 +#define MX27_PAD_LD0__GPIO1_6 0x06 0x036 +#define MX27_PAD_LD1__LD1 0x07 0x004 +#define MX27_PAD_LD1__GPIO1_7 0x07 0x036 +#define MX27_PAD_LD2__LD2 0x08 0x004 +#define MX27_PAD_LD2__GPIO1_8 0x08 0x036 +#define MX27_PAD_LD3__LD3 0x09 0x004 +#define MX27_PAD_LD3__GPIO1_9 0x09 0x036 +#define MX27_PAD_LD4__LD4 0x0a 0x004 +#define MX27_PAD_LD4__GPIO1_10 0x0a 0x036 +#define MX27_PAD_LD5__LD5 0x0b 0x004 +#define MX27_PAD_LD5__GPIO1_11 0x0b 0x036 +#define MX27_PAD_LD6__LD6 0x0c 0x004 +#define MX27_PAD_LD6__GPIO1_12 0x0c 0x036 +#define MX27_PAD_LD7__LD7 0x0d 0x004 +#define MX27_PAD_LD7__GPIO1_13 0x0d 0x036 +#define MX27_PAD_LD8__LD8 0x0e 0x004 +#define MX27_PAD_LD8__GPIO1_14 0x0e 0x036 +#define MX27_PAD_LD9__LD9 0x0f 0x004 +#define MX27_PAD_LD9__GPIO1_15 0x0f 0x036 +#define MX27_PAD_LD10__LD10 0x10 0x004 +#define MX27_PAD_LD10__GPIO1_16 0x10 0x036 +#define MX27_PAD_LD11__LD11 0x11 0x004 +#define MX27_PAD_LD11__GPIO1_17 0x11 0x036 +#define MX27_PAD_LD12__LD12 0x12 0x004 +#define MX27_PAD_LD12__GPIO1_18 0x12 0x036 +#define MX27_PAD_LD13__LD13 0x13 0x004 +#define MX27_PAD_LD13__GPIO1_19 0x13 0x036 +#define MX27_PAD_LD14__LD14 0x14 0x004 +#define MX27_PAD_LD14__GPIO1_20 0x14 0x036 +#define MX27_PAD_LD15__LD15 0x15 0x004 +#define MX27_PAD_LD15__GPIO1_21 0x15 0x036 +#define MX27_PAD_LD16__LD16 0x16 0x004 +#define MX27_PAD_LD16__GPIO1_22 0x16 0x036 +#define MX27_PAD_LD17__LD17 0x17 0x004 +#define MX27_PAD_LD17__GPIO1_23 0x17 0x036 +#define MX27_PAD_REV__REV 0x18 0x004 +#define MX27_PAD_REV__GPIO1_24 0x18 0x036 +#define MX27_PAD_CLS__CLS 0x19 0x004 +#define MX27_PAD_CLS__GPIO1_25 0x19 0x036 +#define MX27_PAD_PS__PS 0x1a 0x004 +#define MX27_PAD_PS__GPIO1_26 0x1a 0x036 +#define MX27_PAD_SPL_SPR__SPL_SPR 0x1b 0x004 +#define MX27_PAD_SPL_SPR__GPIO1_27 0x1b 0x036 +#define MX27_PAD_HSYNC__HSYNC 0x1c 0x004 +#define MX27_PAD_HSYNC__GPIO1_28 0x1c 0x036 +#define MX27_PAD_VSYNC__VSYNC 0x1d 0x004 +#define MX27_PAD_VSYNC__GPIO1_29 0x1d 0x036 +#define MX27_PAD_CONTRAST__CONTRAST 0x1e 0x004 +#define MX27_PAD_CONTRAST__GPIO1_30 0x1e 0x036 +#define MX27_PAD_OE_ACD__OE_ACD 0x1f 0x004 +#define MX27_PAD_OE_ACD__GPIO1_31 0x1f 0x036 +#define MX27_PAD_UNUSED0__UNUSED0 0x20 0x004 +#define MX27_PAD_UNUSED0__GPIO2_0 0x20 0x036 +#define MX27_PAD_UNUSED1__UNUSED1 0x21 0x004 +#define MX27_PAD_UNUSED1__GPIO2_1 0x21 0x036 +#define MX27_PAD_UNUSED2__UNUSED2 0x22 0x004 +#define MX27_PAD_UNUSED2__GPIO2_2 0x22 0x036 +#define MX27_PAD_UNUSED3__UNUSED3 0x23 0x004 +#define MX27_PAD_UNUSED3__GPIO2_3 0x23 0x036 +#define MX27_PAD_SD2_D0__SD2_D0 0x24 0x004 +#define MX27_PAD_SD2_D0__MSHC_DATA0 0x24 0x005 +#define MX27_PAD_SD2_D0__GPIO2_4 0x24 0x036 +#define MX27_PAD_SD2_D1__SD2_D1 0x25 0x004 +#define MX27_PAD_SD2_D1__MSHC_DATA1 0x25 0x005 +#define MX27_PAD_SD2_D1__GPIO2_5 0x25 0x036 +#define MX27_PAD_SD2_D2__SD2_D2 0x26 0x004 +#define MX27_PAD_SD2_D2__MSHC_DATA2 0x26 0x005 +#define MX27_PAD_SD2_D2__GPIO2_6 0x26 0x036 +#define MX27_PAD_SD2_D3__SD2_D3 0x27 0x004 +#define MX27_PAD_SD2_D3__MSHC_DATA3 0x27 0x005 +#define MX27_PAD_SD2_D3__GPIO2_7 0x27 0x036 +#define MX27_PAD_SD2_CMD__SD2_CMD 0x28 0x004 +#define MX27_PAD_SD2_CMD__MSHC_BS 0x28 0x005 +#define MX27_PAD_SD2_CMD__GPIO2_8 0x28 0x036 +#define MX27_PAD_SD2_CLK__SD2_CLK 0x29 0x004 +#define MX27_PAD_SD2_CLK__MSHC_SCLK 0x29 0x005 +#define MX27_PAD_SD2_CLK__GPIO2_9 0x29 0x036 +#define MX27_PAD_CSI_D0__CSI_D0 0x2a 0x000 +#define MX27_PAD_CSI_D0__UART6_TXD 0x2a 0x005 +#define MX27_PAD_CSI_D0__GPIO2_10 0x2a 0x036 +#define MX27_PAD_CSI_D1__CSI_D1 0x2b 0x000 +#define MX27_PAD_CSI_D1__UART6_RXD 0x2b 0x001 +#define MX27_PAD_CSI_D1__GPIO2_11 0x2b 0x036 +#define MX27_PAD_CSI_D2__CSI_D2 0x2c 0x000 +#define MX27_PAD_CSI_D2__UART6_CTS 0x2c 0x005 +#define MX27_PAD_CSI_D2__GPIO2_12 0x2c 0x036 +#define MX27_PAD_CSI_D3__CSI_D3 0x2d 0x000 +#define MX27_PAD_CSI_D3__UART6_RTS 0x2d 0x001 +#define MX27_PAD_CSI_D3__GPIO2_13 0x2d 0x036 +#define MX27_PAD_CSI_D4__CSI_D4 0x2e 0x000 +#define MX27_PAD_CSI_D4__GPIO2_14 0x2e 0x036 +#define MX27_PAD_CSI_MCLK__CSI_MCLK 0x2f 0x004 +#define MX27_PAD_CSI_MCLK__GPIO2_15 0x2f 0x036 +#define MX27_PAD_CSI_PIXCLK__CSI_PIXCLK 0x30 0x000 +#define MX27_PAD_CSI_PIXCLK__GPIO2_16 0x30 0x036 +#define MX27_PAD_CSI_D5__CSI_D5 0x31 0x000 +#define MX27_PAD_CSI_D5__GPIO2_17 0x31 0x036 +#define MX27_PAD_CSI_D6__CSI_D6 0x32 0x000 +#define MX27_PAD_CSI_D6__UART5_TXD 0x32 0x005 +#define MX27_PAD_CSI_D6__GPIO2_18 0x32 0x036 +#define MX27_PAD_CSI_D7__CSI_D7 0x33 0x000 +#define MX27_PAD_CSI_D7__UART5_RXD 0x33 0x001 +#define MX27_PAD_CSI_D7__GPIO2_19 0x33 0x036 +#define MX27_PAD_CSI_VSYNC__CSI_VSYNC 0x34 0x000 +#define MX27_PAD_CSI_VSYNC__UART5_CTS 0x34 0x005 +#define MX27_PAD_CSI_VSYNC__GPIO2_20 0x34 0x036 +#define MX27_PAD_CSI_HSYNC__CSI_HSYNC 0x35 0x000 +#define MX27_PAD_CSI_HSYNC__UART5_RTS 0x35 0x001 +#define MX27_PAD_CSI_HSYNC__GPIO2_21 0x35 0x036 +#define MX27_PAD_USBH1_SUSP__USBH1_SUSP 0x36 0x004 +#define MX27_PAD_USBH1_SUSP__GPIO2_22 0x36 0x036 +#define MX27_PAD_USB_PWR__USB_PWR 0x37 0x004 +#define MX27_PAD_USB_PWR__GPIO2_23 0x37 0x036 +#define MX27_PAD_USB_OC_B__USB_OC_B 0x38 0x000 +#define MX27_PAD_USB_OC_B__GPIO2_24 0x38 0x036 +#define MX27_PAD_USBH1_RCV__USBH1_RCV 0x39 0x004 +#define MX27_PAD_USBH1_RCV__GPIO2_25 0x39 0x036 +#define MX27_PAD_USBH1_FS__USBH1_FS 0x3a 0x004 +#define MX27_PAD_USBH1_FS__UART4_RTS 0x3a 0x001 +#define MX27_PAD_USBH1_FS__GPIO2_26 0x3a 0x036 +#define MX27_PAD_USBH1_OE_B__USBH1_OE_B 0x3b 0x004 +#define MX27_PAD_USBH1_OE_B__GPIO2_27 0x3b 0x036 +#define MX27_PAD_USBH1_TXDM__USBH1_TXDM 0x3c 0x004 +#define MX27_PAD_USBH1_TXDM__UART4_TXD 0x3c 0x005 +#define MX27_PAD_USBH1_TXDM__GPIO2_28 0x3c 0x036 +#define MX27_PAD_USBH1_TXDP__USBH1_TXDP 0x3d 0x004 +#define MX27_PAD_USBH1_TXDP__UART4_CTS 0x3d 0x005 +#define MX27_PAD_USBH1_TXDP__GPIO2_29 0x3d 0x036 +#define MX27_PAD_USBH1_RXDM__USBH1_RXDM 0x3e 0x004 +#define MX27_PAD_USBH1_RXDM__GPIO2_30 0x3e 0x036 +#define MX27_PAD_USBH1_RXDP__USBH1_RXDP 0x3f 0x004 +#define MX27_PAD_USBH1_RXDP__UART4_RXD 0x3f 0x001 +#define MX27_PAD_USBH1_RXDP__GPIO2_31 0x3f 0x036 +#define MX27_PAD_UNUSED4__UNUSED4 0x40 0x004 +#define MX27_PAD_UNUSED4__GPIO3_0 0x40 0x036 +#define MX27_PAD_UNUSED5__UNUSED5 0x41 0x004 +#define MX27_PAD_UNUSED5__GPIO3_1 0x41 0x036 +#define MX27_PAD_UNUSED6__UNUSED6 0x42 0x004 +#define MX27_PAD_UNUSED6__GPIO3_2 0x42 0x036 +#define MX27_PAD_UNUSED7__UNUSED7 0x43 0x004 +#define MX27_PAD_UNUSED7__GPIO3_3 0x43 0x036 +#define MX27_PAD_UNUSED8__UNUSED8 0x44 0x004 +#define MX27_PAD_UNUSED8__GPIO3_4 0x44 0x036 +#define MX27_PAD_I2C2_SDA__I2C2_SDA 0x45 0x004 +#define MX27_PAD_I2C2_SDA__GPIO3_5 0x45 0x036 +#define MX27_PAD_I2C2_SCL__I2C2_SCL 0x46 0x004 +#define MX27_PAD_I2C2_SCL__GPIO3_6 0x46 0x036 +#define MX27_PAD_USBOTG_DATA5__USBOTG_DATA5 0x47 0x004 +#define MX27_PAD_USBOTG_DATA5__GPIO3_7 0x47 0x036 +#define MX27_PAD_USBOTG_DATA6__USBOTG_DATA6 0x48 0x004 +#define MX27_PAD_USBOTG_DATA6__GPIO3_8 0x48 0x036 +#define MX27_PAD_USBOTG_DATA0__USBOTG_DATA0 0x49 0x004 +#define MX27_PAD_USBOTG_DATA0__GPIO3_9 0x49 0x036 +#define MX27_PAD_USBOTG_DATA2__USBOTG_DATA2 0x4a 0x004 +#define MX27_PAD_USBOTG_DATA2__GPIO3_10 0x4a 0x036 +#define MX27_PAD_USBOTG_DATA1__USBOTG_DATA1 0x4b 0x004 +#define MX27_PAD_USBOTG_DATA1__GPIO3_11 0x4b 0x036 +#define MX27_PAD_USBOTG_DATA4__USBOTG_DATA4 0x4c 0x004 +#define MX27_PAD_USBOTG_DATA4__GPIO3_12 0x4c 0x036 +#define MX27_PAD_USBOTG_DATA3__USBOTG_DATA3 0x4d 0x004 +#define MX27_PAD_USBOTG_DATA3__GPIO3_13 0x4d 0x036 +#define MX27_PAD_TOUT__TOUT 0x4e 0x004 +#define MX27_PAD_TOUT__GPIO3_14 0x4e 0x036 +#define MX27_PAD_TIN__TIN 0x4f 0x000 +#define MX27_PAD_TIN__GPIO3_15 0x4f 0x036 +#define MX27_PAD_SSI4_FS__SSI4_FS 0x50 0x004 +#define MX27_PAD_SSI4_FS__GPIO3_16 0x50 0x036 +#define MX27_PAD_SSI4_RXDAT__SSI4_RXDAT 0x51 0x004 +#define MX27_PAD_SSI4_RXDAT__GPIO3_17 0x51 0x036 +#define MX27_PAD_SSI4_TXDAT__SSI4_TXDAT 0x52 0x004 +#define MX27_PAD_SSI4_TXDAT__GPIO3_18 0x52 0x036 +#define MX27_PAD_SSI4_CLK__SSI4_CLK 0x53 0x004 +#define MX27_PAD_SSI4_CLK__GPIO3_19 0x53 0x036 +#define MX27_PAD_SSI1_FS__SSI1_FS 0x54 0x004 +#define MX27_PAD_SSI1_FS__GPIO3_20 0x54 0x036 +#define MX27_PAD_SSI1_RXDAT__SSI1_RXDAT 0x55 0x004 +#define MX27_PAD_SSI1_RXDAT__GPIO3_21 0x55 0x036 +#define MX27_PAD_SSI1_TXDAT__SSI1_TXDAT 0x56 0x004 +#define MX27_PAD_SSI1_TXDAT__GPIO3_22 0x56 0x036 +#define MX27_PAD_SSI1_CLK__SSI1_CLK 0x57 0x004 +#define MX27_PAD_SSI1_CLK__GPIO3_23 0x57 0x036 +#define MX27_PAD_SSI2_FS__SSI2_FS 0x58 0x004 +#define MX27_PAD_SSI2_FS__GPT5_TOUT 0x58 0x005 +#define MX27_PAD_SSI2_FS__GPIO3_24 0x58 0x036 +#define MX27_PAD_SSI2_RXDAT__SSI2_RXDAT 0x59 0x004 +#define MX27_PAD_SSI2_RXDAT__GPTS_TIN 0x59 0x001 +#define MX27_PAD_SSI2_RXDAT__GPIO3_25 0x59 0x036 +#define MX27_PAD_SSI2_TXDAT__SSI2_TXDAT 0x5a 0x004 +#define MX27_PAD_SSI2_TXDAT__GPT4_TOUT 0x5a 0x005 +#define MX27_PAD_SSI2_TXDAT__GPIO3_26 0x5a 0x036 +#define MX27_PAD_SSI2_CLK__SSI2_CLK 0x5b 0x004 +#define MX27_PAD_SSI2_CLK__GPT4_TIN 0x5b 0x001 +#define MX27_PAD_SSI2_CLK__GPIO3_27 0x5b 0x036 +#define MX27_PAD_SSI3_FS__SSI3_FS 0x5c 0x004 +#define MX27_PAD_SSI3_FS__SLCDC2_D0 0x5c 0x001 +#define MX27_PAD_SSI3_FS__GPIO3_28 0x5c 0x036 +#define MX27_PAD_SSI3_RXDAT__SSI3_RXDAT 0x5d 0x004 +#define MX27_PAD_SSI3_RXDAT__SLCDC2_RS 0x5d 0x001 +#define MX27_PAD_SSI3_RXDAT__GPIO3_29 0x5d 0x036 +#define MX27_PAD_SSI3_TXDAT__SSI3_TXDAT 0x5e 0x004 +#define MX27_PAD_SSI3_TXDAT__SLCDC2_CS 0x5e 0x001 +#define MX27_PAD_SSI3_TXDAT__GPIO3_30 0x5e 0x036 +#define MX27_PAD_SSI3_CLK__SSI3_CLK 0x5f 0x004 +#define MX27_PAD_SSI3_CLK__SLCDC2_CLK 0x5f 0x001 +#define MX27_PAD_SSI3_CLK__GPIO3_31 0x5f 0x036 +#define MX27_PAD_SD3_CMD__SD3_CMD 0x60 0x004 +#define MX27_PAD_SD3_CMD__FEC_TXD0 0x60 0x006 +#define MX27_PAD_SD3_CMD__GPIO4_0 0x60 0x036 +#define MX27_PAD_SD3_CLK__SD3_CLK 0x61 0x004 +#define MX27_PAD_SD3_CLK__ETMTRACEPKT15 0x61 0x005 +#define MX27_PAD_SD3_CLK__FEC_TXD1 0x61 0x006 +#define MX27_PAD_SD3_CLK__GPIO4_1 0x61 0x036 +#define MX27_PAD_ATA_DATA0__ATA_DATA0 0x62 0x004 +#define MX27_PAD_ATA_DATA0__SD3_D0 0x62 0x005 +#define MX27_PAD_ATA_DATA0__FEC_TXD2 0x62 0x006 +#define MX27_PAD_ATA_DATA0__GPIO4_2 0x62 0x036 +#define MX27_PAD_ATA_DATA1__ATA_DATA1 0x63 0x004 +#define MX27_PAD_ATA_DATA1__SD3_D1 0x63 0x005 +#define MX27_PAD_ATA_DATA1__FEC_TXD3 0x63 0x006 +#define MX27_PAD_ATA_DATA1__GPIO4_3 0x63 0x036 +#define MX27_PAD_ATA_DATA2__ATA_DATA2 0x64 0x004 +#define MX27_PAD_ATA_DATA2__SD3_D2 0x64 0x005 +#define MX27_PAD_ATA_DATA2__FEC_RX_ER 0x64 0x002 +#define MX27_PAD_ATA_DATA2__GPIO4_4 0x64 0x036 +#define MX27_PAD_ATA_DATA3__ATA_DATA3 0x65 0x004 +#define MX27_PAD_ATA_DATA3__SD3_D3 0x65 0x005 +#define MX27_PAD_ATA_DATA3__FEC_RXD1 0x65 0x002 +#define MX27_PAD_ATA_DATA3__GPIO4_5 0x65 0x036 +#define MX27_PAD_ATA_DATA4__ATA_DATA4 0x66 0x004 +#define MX27_PAD_ATA_DATA4__ETMTRACEPKT14 0x66 0x005 +#define MX27_PAD_ATA_DATA4__FEC_RXD2 0x66 0x002 +#define MX27_PAD_ATA_DATA4__GPIO4_6 0x66 0x036 +#define MX27_PAD_ATA_DATA5__ATA_DATA5 0x67 0x004 +#define MX27_PAD_ATA_DATA5__ETMTRACEPKT13 0x67 0x005 +#define MX27_PAD_ATA_DATA5__FEC_RXD3 0x67 0x002 +#define MX27_PAD_ATA_DATA5__GPIO4_7 0x67 0x036 +#define MX27_PAD_ATA_DATA6__ATA_DATA6 0x68 0x004 +#define MX27_PAD_ATA_DATA6__FEC_MDIO 0x68 0x005 +#define MX27_PAD_ATA_DATA6__GPIO4_8 0x68 0x036 +#define MX27_PAD_ATA_DATA7__ATA_DATA7 0x69 0x004 +#define MX27_PAD_ATA_DATA7__ETMTRACEPKT12 0x69 0x005 +#define MX27_PAD_ATA_DATA7__FEC_MDC 0x69 0x006 +#define MX27_PAD_ATA_DATA7__GPIO4_9 0x69 0x036 +#define MX27_PAD_ATA_DATA8__ATA_DATA8 0x6a 0x004 +#define MX27_PAD_ATA_DATA8__ETMTRACEPKT11 0x6a 0x005 +#define MX27_PAD_ATA_DATA8__FEC_CRS 0x6a 0x002 +#define MX27_PAD_ATA_DATA8__GPIO4_10 0x6a 0x036 +#define MX27_PAD_ATA_DATA9__ATA_DATA9 0x6b 0x004 +#define MX27_PAD_ATA_DATA9__ETMTRACEPKT10 0x6b 0x005 +#define MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x6b 0x002 +#define MX27_PAD_ATA_DATA9__GPIO4_11 0x6b 0x036 +#define MX27_PAD_ATA_DATA10__ATA_DATA10 0x6c 0x004 +#define MX27_PAD_ATA_DATA10__ETMTRACEPKT9 0x6c 0x005 +#define MX27_PAD_ATA_DATA10__FEC_RXD0 0x6c 0x002 +#define MX27_PAD_ATA_DATA10__GPIO4_12 0x6c 0x036 +#define MX27_PAD_ATA_DATA11__ATA_DATA11 0x6d 0x004 +#define MX27_PAD_ATA_DATA11__ETMTRACEPKT8 0x6d 0x005 +#define MX27_PAD_ATA_DATA11__FEC_RX_DV 0x6d 0x002 +#define MX27_PAD_ATA_DATA11__GPIO4_13 0x6d 0x036 +#define MX27_PAD_ATA_DATA12__ATA_DATA12 0x6e 0x004 +#define MX27_PAD_ATA_DATA12__ETMTRACEPKT7 0x6e 0x005 +#define MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x6e 0x002 +#define MX27_PAD_ATA_DATA12__GPIO4_14 0x6e 0x036 +#define MX27_PAD_ATA_DATA13__ATA_DATA13 0x6f 0x004 +#define MX27_PAD_ATA_DATA13__ETMTRACEPKT6 0x6f 0x005 +#define MX27_PAD_ATA_DATA13__FEC_COL 0x6f 0x002 +#define MX27_PAD_ATA_DATA13__GPIO4_15 0x6f 0x036 +#define MX27_PAD_ATA_DATA14__ATA_DATA14 0x70 0x004 +#define MX27_PAD_ATA_DATA14__ETMTRACEPKT5 0x70 0x005 +#define MX27_PAD_ATA_DATA14__FEC_TX_ER 0x70 0x006 +#define MX27_PAD_ATA_DATA14__GPIO4_16 0x70 0x036 +#define MX27_PAD_I2C_DATA__I2C_DATA 0x71 0x004 +#define MX27_PAD_I2C_DATA__GPIO4_17 0x71 0x036 +#define MX27_PAD_I2C_CLK__I2C_CLK 0x72 0x004 +#define MX27_PAD_I2C_CLK__GPIO4_18 0x72 0x036 +#define MX27_PAD_CSPI2_SS2__CSPI2_SS2 0x73 0x004 +#define MX27_PAD_CSPI2_SS2__USBH2_DATA4 0x73 0x005 +#define MX27_PAD_CSPI2_SS2__GPIO4_19 0x73 0x036 +#define MX27_PAD_CSPI2_SS1__CSPI2_SS1 0x74 0x004 +#define MX27_PAD_CSPI2_SS1__USBH2_DATA3 0x74 0x005 +#define MX27_PAD_CSPI2_SS1__GPIO4_20 0x74 0x036 +#define MX27_PAD_CSPI2_SS0__CSPI2_SS0 0x75 0x004 +#define MX27_PAD_CSPI2_SS0__USBH2_DATA6 0x75 0x005 +#define MX27_PAD_CSPI2_SS0__GPIO4_21 0x75 0x036 +#define MX27_PAD_CSPI2_SCLK__CSPI2_SCLK 0x76 0x004 +#define MX27_PAD_CSPI2_SCLK__USBH2_DATA0 0x76 0x005 +#define MX27_PAD_CSPI2_SCLK__GPIO4_22 0x76 0x036 +#define MX27_PAD_CSPI2_MISO__CSPI2_MISO 0x77 0x004 +#define MX27_PAD_CSPI2_MISO__USBH2_DATA2 0x77 0x005 +#define MX27_PAD_CSPI2_MISO__GPIO4_23 0x77 0x036 +#define MX27_PAD_CSPI2_MOSI__CSPI2_MOSI 0x78 0x004 +#define MX27_PAD_CSPI2_MOSI__USBH2_DATA1 0x78 0x005 +#define MX27_PAD_CSPI2_MOSI__GPIO4_24 0x78 0x036 +#define MX27_PAD_CSPI1_RDY__CSPI1_RDY 0x79 0x000 +#define MX27_PAD_CSPI1_RDY__GPIO4_25 0x79 0x036 +#define MX27_PAD_CSPI1_SS2__CSPI1_SS2 0x7a 0x004 +#define MX27_PAD_CSPI1_SS2__USBH2_DATA5 0x7a 0x005 +#define MX27_PAD_CSPI1_SS2__GPIO4_26 0x7a 0x036 +#define MX27_PAD_CSPI1_SS1__CSPI1_SS1 0x7b 0x004 +#define MX27_PAD_CSPI1_SS1__GPIO4_27 0x7b 0x036 +#define MX27_PAD_CSPI1_SS0__CSPI1_SS0 0x7c 0x004 +#define MX27_PAD_CSPI1_SS0__GPIO4_28 0x7c 0x036 +#define MX27_PAD_CSPI1_SCLK__CSPI1_SCLK 0x7d 0x004 +#define MX27_PAD_CSPI1_SCLK__GPIO4_29 0x7d 0x036 +#define MX27_PAD_CSPI1_MISO__CSPI1_MISO 0x7e 0x004 +#define MX27_PAD_CSPI1_MISO__GPIO4_30 0x7e 0x036 +#define MX27_PAD_CSPI1_MOSI__CSPI1_MOSI 0x7f 0x004 +#define MX27_PAD_CSPI1_MOSI__GPIO4_31 0x7f 0x036 +#define MX27_PAD_USBOTG_NXT__USBOTG_NXT 0x80 0x000 +#define MX27_PAD_USBOTG_NXT__KP_COL6A 0x80 0x005 +#define MX27_PAD_USBOTG_NXT__GPIO5_0 0x80 0x036 +#define MX27_PAD_USBOTG_STP__USBOTG_STP 0x81 0x004 +#define MX27_PAD_USBOTG_STP__KP_ROW6A 0x81 0x005 +#define MX27_PAD_USBOTG_STP__GPIO5_1 0x81 0x036 +#define MX27_PAD_USBOTG_DIR__USBOTG_DIR 0x82 0x000 +#define MX27_PAD_USBOTG_DIR__KP_ROW7A 0x82 0x005 +#define MX27_PAD_USBOTG_DIR__GPIO5_2 0x82 0x036 +#define MX27_PAD_UART2_CTS__UART2_CTS 0x83 0x004 +#define MX27_PAD_UART2_CTS__KP_COL7 0x83 0x005 +#define MX27_PAD_UART2_CTS__GPIO5_3 0x83 0x036 +#define MX27_PAD_UART2_RTS__UART2_RTS 0x84 0x000 +#define MX27_PAD_UART2_RTS__KP_ROW7 0x84 0x005 +#define MX27_PAD_UART2_RTS__GPIO5_4 0x84 0x036 +#define MX27_PAD_PWMO__PWMO 0x85 0x004 +#define MX27_PAD_PWMO__GPIO5_5 0x85 0x036 +#define MX27_PAD_UART2_TXD__UART2_TXD 0x86 0x004 +#define MX27_PAD_UART2_TXD__KP_COL6 0x86 0x005 +#define MX27_PAD_UART2_TXD__GPIO5_6 0x86 0x036 +#define MX27_PAD_UART2_RXD__UART2_RXD 0x87 0x000 +#define MX27_PAD_UART2_RXD__KP_ROW6 0x87 0x005 +#define MX27_PAD_UART2_RXD__GPIO5_7 0x87 0x036 +#define MX27_PAD_UART3_TXD__UART3_TXD 0x88 0x004 +#define MX27_PAD_UART3_TXD__GPIO5_8 0x88 0x036 +#define MX27_PAD_UART3_RXD__UART3_RXD 0x89 0x000 +#define MX27_PAD_UART3_RXD__GPIO5_9 0x89 0x036 +#define MX27_PAD_UART3_CTS__UART3_CTS 0x8a 0x004 +#define MX27_PAD_UART3_CTS__GPIO5_10 0x8a 0x036 +#define MX27_PAD_UART3_RTS__UART3_RTS 0x8b 0x000 +#define MX27_PAD_UART3_RTS__GPIO5_11 0x8b 0x036 +#define MX27_PAD_UART1_TXD__UART1_TXD 0x8c 0x004 +#define MX27_PAD_UART1_TXD__GPIO5_12 0x8c 0x036 +#define MX27_PAD_UART1_RXD__UART1_RXD 0x8d 0x000 +#define MX27_PAD_UART1_RXD__GPIO5_13 0x8d 0x036 +#define MX27_PAD_UART1_CTS__UART1_CTS 0x8e 0x004 +#define MX27_PAD_UART1_CTS__GPIO5_14 0x8e 0x036 +#define MX27_PAD_UART1_RTS__UART1_RTS 0x8f 0x000 +#define MX27_PAD_UART1_RTS__GPIO5_15 0x8f 0x036 +#define MX27_PAD_RTCK__RTCK 0x90 0x004 +#define MX27_PAD_RTCK__OWIRE 0x90 0x005 +#define MX27_PAD_RTCK__GPIO5_16 0x90 0x036 +#define MX27_PAD_RESET_OUT_B__RESET_OUT_B 0x91 0x004 +#define MX27_PAD_RESET_OUT_B__GPIO5_17 0x91 0x036 +#define MX27_PAD_SD1_D0__SD1_D0 0x92 0x004 +#define MX27_PAD_SD1_D0__CSPI3_MISO 0x92 0x001 +#define MX27_PAD_SD1_D0__GPIO5_18 0x92 0x036 +#define MX27_PAD_SD1_D1__SD1_D1 0x93 0x004 +#define MX27_PAD_SD1_D1__GPIO5_19 0x93 0x036 +#define MX27_PAD_SD1_D2__SD1_D2 0x94 0x004 +#define MX27_PAD_SD1_D2__GPIO5_20 0x94 0x036 +#define MX27_PAD_SD1_D3__SD1_D3 0x95 0x004 +#define MX27_PAD_SD1_D3__CSPI3_SS 0x95 0x005 +#define MX27_PAD_SD1_D3__GPIO5_21 0x95 0x036 +#define MX27_PAD_SD1_CMD__SD1_CMD 0x96 0x004 +#define MX27_PAD_SD1_CMD__CSPI3_MOSI 0x96 0x005 +#define MX27_PAD_SD1_CMD__GPIO5_22 0x96 0x036 +#define MX27_PAD_SD1_CLK__SD1_CLK 0x97 0x004 +#define MX27_PAD_SD1_CLK__CSPI3_SCLK 0x97 0x005 +#define MX27_PAD_SD1_CLK__GPIO5_23 0x97 0x036 +#define MX27_PAD_USBOTG_CLK__USBOTG_CLK 0x98 0x000 +#define MX27_PAD_USBOTG_CLK__GPIO5_24 0x98 0x036 +#define MX27_PAD_USBOTG_DATA7__USBOTG_DATA7 0x99 0x004 +#define MX27_PAD_USBOTG_DATA7__GPIO5_25 0x99 0x036 +#define MX27_PAD_UNUSED9__UNUSED9 0x9a 0x004 +#define MX27_PAD_UNUSED9__GPIO5_26 0x9a 0x036 +#define MX27_PAD_UNUSED10__UNUSED10 0x9b 0x004 +#define MX27_PAD_UNUSED10__GPIO5_27 0x9b 0x036 +#define MX27_PAD_UNUSED11__UNUSED11 0x9c 0x004 +#define MX27_PAD_UNUSED11__GPIO5_28 0x9c 0x036 +#define MX27_PAD_UNUSED12__UNUSED12 0x9d 0x004 +#define MX27_PAD_UNUSED12__GPIO5_29 0x9d 0x036 +#define MX27_PAD_UNUSED13__UNUSED13 0x9e 0x004 +#define MX27_PAD_UNUSED13__GPIO5_30 0x9e 0x036 +#define MX27_PAD_UNUSED14__UNUSED14 0x9f 0x004 +#define MX27_PAD_UNUSED14__GPIO5_31 0x9f 0x036 +#define MX27_PAD_NFRB__NFRB 0xa0 0x000 +#define MX27_PAD_NFRB__ETMTRACEPKT3 0xa0 0x005 +#define MX27_PAD_NFRB__GPIO6_0 0xa0 0x036 +#define MX27_PAD_NFCLE__NFCLE 0xa1 0x004 +#define MX27_PAD_NFCLE__ETMTRACEPKT0 0xa1 0x005 +#define MX27_PAD_NFCLE__GPIO6_1 0xa1 0x036 +#define MX27_PAD_NFWP_B__NFWP_B 0xa2 0x004 +#define MX27_PAD_NFWP_B__ETMTRACEPKT1 0xa2 0x005 +#define MX27_PAD_NFWP_B__GPIO6_2 0xa2 0x036 +#define MX27_PAD_NFCE_B__NFCE_B 0xa3 0x004 +#define MX27_PAD_NFCE_B__ETMTRACEPKT2 0xa3 0x005 +#define MX27_PAD_NFCE_B__GPIO6_3 0xa3 0x036 +#define MX27_PAD_NFALE__NFALE 0xa4 0x004 +#define MX27_PAD_NFALE__ETMPIPESTAT0 0xa4 0x005 +#define MX27_PAD_NFALE__GPIO6_4 0xa4 0x036 +#define MX27_PAD_NFRE_B__NFRE_B 0xa5 0x004 +#define MX27_PAD_NFRE_B__ETMPIPESTAT1 0xa5 0x005 +#define MX27_PAD_NFRE_B__GPIO6_5 0xa5 0x036 +#define MX27_PAD_NFWE_B__NFWE_B 0xa6 0x004 +#define MX27_PAD_NFWE_B__ETMPIPESTAT2 0xa6 0x005 +#define MX27_PAD_NFWE_B__GPIO6_6 0xa6 0x036 +#define MX27_PAD_PC_POE__PC_POE 0xa7 0x004 +#define MX27_PAD_PC_POE__ATA_BUFFER_EN 0xa7 0x005 +#define MX27_PAD_PC_POE__GPIO6_7 0xa7 0x036 +#define MX27_PAD_PC_RW_B__PC_RW_B 0xa8 0x004 +#define MX27_PAD_PC_RW_B__ATA_IORDY 0xa8 0x001 +#define MX27_PAD_PC_RW_B__GPIO6_8 0xa8 0x036 +#define MX27_PAD_IOIS16__IOIS16 0xa9 0x000 +#define MX27_PAD_IOIS16__ATA_INTRQ 0xa9 0x001 +#define MX27_PAD_IOIS16__GPIO6_9 0xa9 0x036 +#define MX27_PAD_PC_RST__PC_RST 0xaa 0x004 +#define MX27_PAD_PC_RST__ATA_RESET_B 0xaa 0x005 +#define MX27_PAD_PC_RST__GPIO6_10 0xaa 0x036 +#define MX27_PAD_PC_BVD2__PC_BVD2 0xab 0x000 +#define MX27_PAD_PC_BVD2__ATA_DMACK 0xab 0x005 +#define MX27_PAD_PC_BVD2__GPIO6_11 0xab 0x036 +#define MX27_PAD_PC_BVD1__PC_BVD1 0xac 0x000 +#define MX27_PAD_PC_BVD1__ATA_DMARQ 0xac 0x001 +#define MX27_PAD_PC_BVD1__GPIO6_12 0xac 0x036 +#define MX27_PAD_PC_VS2__PC_VS2 0xad 0x000 +#define MX27_PAD_PC_VS2__ATA_DA0 0xad 0x005 +#define MX27_PAD_PC_VS2__GPIO6_13 0xad 0x036 +#define MX27_PAD_PC_VS1__PC_VS1 0xae 0x000 +#define MX27_PAD_PC_VS1__ATA_DA1 0xae 0x005 +#define MX27_PAD_PC_VS1__GPIO6_14 0xae 0x036 +#define MX27_PAD_CLKO__CLKO 0xaf 0x004 +#define MX27_PAD_CLKO__GPIO6_15 0xaf 0x036 +#define MX27_PAD_PC_PWRON__PC_PWRON 0xb0 0x000 +#define MX27_PAD_PC_PWRON__ATA_DA2 0xb0 0x005 +#define MX27_PAD_PC_PWRON__GPIO6_16 0xb0 0x036 +#define MX27_PAD_PC_READY__PC_READY 0xb1 0x000 +#define MX27_PAD_PC_READY__ATA_CS0 0xb1 0x005 +#define MX27_PAD_PC_READY__GPIO6_17 0xb1 0x036 +#define MX27_PAD_PC_WAIT_B__PC_WAIT_B 0xb2 0x000 +#define MX27_PAD_PC_WAIT_B__ATA_CS1 0xb2 0x005 +#define MX27_PAD_PC_WAIT_B__GPIO6_18 0xb2 0x036 +#define MX27_PAD_PC_CD2_B__PC_CD2_B 0xb3 0x000 +#define MX27_PAD_PC_CD2_B__ATA_DIOW 0xb3 0x005 +#define MX27_PAD_PC_CD2_B__GPIO6_19 0xb3 0x036 +#define MX27_PAD_PC_CD1_B__PC_CD1_B 0xb4 0x000 +#define MX27_PAD_PC_CD1_B__ATA_DIOR 0xb4 0x005 +#define MX27_PAD_PC_CD1_B__GPIO6_20 0xb4 0x036 +#define MX27_PAD_CS4_B__CS4_B 0xb5 0x004 +#define MX27_PAD_CS4_B__ETMTRACESYNC 0xb5 0x005 +#define MX27_PAD_CS4_B__GPIO6_21 0xb5 0x036 +#define MX27_PAD_CS5_B__CS5_B 0xb6 0x004 +#define MX27_PAD_CS5_B__ETMTRACECLK 0xb6 0x005 +#define MX27_PAD_CS5_B__GPIO6_22 0xb6 0x036 +#define MX27_PAD_ATA_DATA15__ATA_DATA15 0xb7 0x004 +#define MX27_PAD_ATA_DATA15__ETMTRACEPKT4 0xb7 0x005 +#define MX27_PAD_ATA_DATA15__FEC_TX_EN 0xb7 0x006 +#define MX27_PAD_ATA_DATA15__GPIO6_23 0xb7 0x036 +#define MX27_PAD_UNUSED15__UNUSED15 0xb8 0x004 +#define MX27_PAD_UNUSED15__GPIO6_24 0xb8 0x036 +#define MX27_PAD_UNUSED16__UNUSED16 0xb9 0x004 +#define MX27_PAD_UNUSED16__GPIO6_25 0xb9 0x036 +#define MX27_PAD_UNUSED17__UNUSED17 0xba 0x004 +#define MX27_PAD_UNUSED17__GPIO6_26 0xba 0x036 +#define MX27_PAD_UNUSED18__UNUSED18 0xbb 0x004 +#define MX27_PAD_UNUSED18__GPIO6_27 0xbb 0x036 +#define MX27_PAD_UNUSED19__UNUSED19 0xbc 0x004 +#define MX27_PAD_UNUSED19__GPIO6_28 0xbc 0x036 +#define MX27_PAD_UNUSED20__UNUSED20 0xbd 0x004 +#define MX27_PAD_UNUSED20__GPIO6_29 0xbd 0x036 +#define MX27_PAD_UNUSED21__UNUSED21 0xbe 0x004 +#define MX27_PAD_UNUSED21__GPIO6_30 0xbe 0x036 +#define MX27_PAD_UNUSED22__UNUSED22 0xbf 0x004 +#define MX27_PAD_UNUSED22__GPIO6_31 0xbf 0x036 + +#endif /* __DTS_IMX27_PINFUNC_H */ -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v5 4/8] ARM: dts: imx27 pinctrl 2013-10-24 15:38 [PATCH v5 0/8] ARM: imx27 pinctrl Markus Pargmann ` (2 preceding siblings ...) 2013-10-24 15:38 ` [PATCH v5 3/8] ARM: dts: imx27 pin functions Markus Pargmann @ 2013-10-24 15:38 ` Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 5/8] ARM: dts: imx27 phyCARD-S pinctrl Markus Pargmann ` (3 subsequent siblings) 7 siblings, 0 replies; 11+ messages in thread From: Markus Pargmann @ 2013-10-24 15:38 UTC (permalink / raw) To: linux-arm-kernel Pinctrl driver node and pin group definitions for other driver nodes. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> --- arch/arm/boot/dts/imx27.dtsi | 102 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 102 insertions(+) diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi index b7a1c6d..641a63d 100644 --- a/arch/arm/boot/dts/imx27.dtsi +++ b/arch/arm/boot/dts/imx27.dtsi @@ -10,6 +10,7 @@ */ #include "skeleton.dtsi" +#include "imx27-pinfunc.h" / { aliases { @@ -235,6 +236,12 @@ status = "disabled"; }; + iomuxc: iomuxc at 10015000 { + compatible = "fsl,imx27-iomuxc"; + reg = <0x10015000 0x600>; + + }; + gpio1: gpio at 10015000 { compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; reg = <0x10015000 0x100>; @@ -467,3 +474,98 @@ }; }; }; + +&iomuxc { + fec { + pinctrl_fec1_1: fec1-1 { + fsl,pins = < + MX27_PAD_SD3_CMD__FEC_TXD0 0x0 + MX27_PAD_SD3_CLK__FEC_TXD1 0x0 + MX27_PAD_ATA_DATA0__FEC_TXD2 0x0 + MX27_PAD_ATA_DATA1__FEC_TXD3 0x0 + MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0 + MX27_PAD_ATA_DATA3__FEC_RXD1 0x0 + MX27_PAD_ATA_DATA4__FEC_RXD2 0x0 + MX27_PAD_ATA_DATA5__FEC_RXD3 0x0 + MX27_PAD_ATA_DATA6__FEC_MDIO 0x0 + MX27_PAD_ATA_DATA7__FEC_MDC 0x0 + MX27_PAD_ATA_DATA8__FEC_CRS 0x0 + MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0 + MX27_PAD_ATA_DATA10__FEC_RXD0 0x0 + MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0 + MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0 + MX27_PAD_ATA_DATA13__FEC_COL 0x0 + MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0 + MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0 + >; + }; + }; + + i2c { + pinctrl_i2c1_1: i2c1-1 { + fsl,pins = < + MX27_PAD_I2C_DATA__I2C_DATA 0x0 + MX27_PAD_I2C_CLK__I2C_CLK 0x0 + >; + }; + + pinctrl_i2c2_1: i2c2-1 { + fsl,pins = < + MX27_PAD_I2C2_SDA__I2C2_SDA 0x0 + MX27_PAD_I2C2_SCL__I2C2_SCL 0x0 + >; + }; + }; + + owire { + pinctrl_owire1_1: owire1-1 { + fsl,pins = < + MX27_PAD_RTCK__OWIRE 0x0 + >; + }; + }; + + uart { + pinctrl_uart1_1: uart1-1 { + fsl,pins = < + MX27_PAD_UART1_TXD__UART1_TXD 0x0 + MX27_PAD_UART1_RXD__UART1_RXD 0x0 + >; + }; + + pinctrl_uart1_rtscts_1: uart1-rtscts-1 { + fsl,pins = < + MX27_PAD_UART1_CTS__UART1_CTS 0x0 + MX27_PAD_UART1_RTS__UART1_RTS 0x0 + >; + }; + + pinctrl_uart2_1: uart2-1 { + fsl,pins = < + MX27_PAD_UART2_TXD__UART2_TXD 0x0 + MX27_PAD_UART2_RXD__UART2_RXD 0x0 + >; + }; + + pinctrl_uart2_rtscts_1: uart2-rtscts-1 { + fsl,pins = < + MX27_PAD_UART2_CTS__UART2_CTS 0x0 + MX27_PAD_UART2_RTS__UART2_RTS 0x0 + >; + }; + + pinctrl_uart3_1: uart3-1 { + fsl,pins = < + MX27_PAD_UART3_TXD__UART3_TXD 0x0 + MX27_PAD_UART3_RXD__UART3_RXD 0x0 + >; + }; + + pinctrl_uart3_rtscts_1: uart3-rtscts-1 { + fsl,pins = < + MX27_PAD_UART3_CTS__UART3_CTS 0x0 + MX27_PAD_UART3_RTS__UART3_RTS 0x0 + >; + }; + }; +}; -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v5 5/8] ARM: dts: imx27 phyCARD-S pinctrl 2013-10-24 15:38 [PATCH v5 0/8] ARM: imx27 pinctrl Markus Pargmann ` (3 preceding siblings ...) 2013-10-24 15:38 ` [PATCH v5 4/8] ARM: dts: imx27 pinctrl Markus Pargmann @ 2013-10-24 15:38 ` Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 6/8] ARM: dts: imx27 phycore move uart1 to rdk Markus Pargmann ` (2 subsequent siblings) 7 siblings, 0 replies; 11+ messages in thread From: Markus Pargmann @ 2013-10-24 15:38 UTC (permalink / raw) To: linux-arm-kernel Enable pinctrl for phyCARD-S devices. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> --- arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts | 10 ++++++++++ arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts | 4 ++++ 2 files changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts index 5a31c77..505e688 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts @@ -54,6 +54,8 @@ }; &i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_1>; status = "okay"; rtc at 51 { @@ -69,6 +71,8 @@ }; &owire { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_owire1_1>; status = "okay"; }; @@ -79,15 +83,21 @@ &uart1 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1_1 &pinctrl_uart1_rtscts_1>; status = "okay"; }; &uart2 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2_1 &pinctrl_uart2_rtscts_1>; status = "okay"; }; &uart3 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3_1 &pinctrl_uart3_rtscts_1>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts b/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts index c8d57d1..0cee738 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts @@ -30,10 +30,14 @@ }; &fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1_1>; status = "okay"; }; &i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2_1>; status = "okay"; at24 at 52 { -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v5 6/8] ARM: dts: imx27 phycore move uart1 to rdk 2013-10-24 15:38 [PATCH v5 0/8] ARM: imx27 pinctrl Markus Pargmann ` (4 preceding siblings ...) 2013-10-24 15:38 ` [PATCH v5 5/8] ARM: dts: imx27 phyCARD-S pinctrl Markus Pargmann @ 2013-10-24 15:38 ` Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 7/8] ARM: dts: imx27 phycore pinctrl Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 8/8] ARM: imx27: enable pinctrl Markus Pargmann 7 siblings, 0 replies; 11+ messages in thread From: Markus Pargmann @ 2013-10-24 15:38 UTC (permalink / raw) To: linux-arm-kernel uart1 is not used on SOM. It is passed directly to the rdk board. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> --- arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts | 1 + arch/arm/boot/dts/imx27-phytec-phycore-som.dts | 4 ---- 2 files changed, 1 insertion(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts index 0fc6551..ad76d88 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts @@ -29,6 +29,7 @@ &uart1 { fsl,uart-has-rtscts; + status = "okay"; }; &uart2 { diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dts b/arch/arm/boot/dts/imx27-phytec-phycore-som.dts index 4ec402c..648541a 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycore-som.dts @@ -165,10 +165,6 @@ status = "okay"; }; -&uart1 { - status = "okay"; -}; - &weim { status = "okay"; -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v5 7/8] ARM: dts: imx27 phycore pinctrl 2013-10-24 15:38 [PATCH v5 0/8] ARM: imx27 pinctrl Markus Pargmann ` (5 preceding siblings ...) 2013-10-24 15:38 ` [PATCH v5 6/8] ARM: dts: imx27 phycore move uart1 to rdk Markus Pargmann @ 2013-10-24 15:38 ` Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 8/8] ARM: imx27: enable pinctrl Markus Pargmann 7 siblings, 0 replies; 11+ messages in thread From: Markus Pargmann @ 2013-10-24 15:38 UTC (permalink / raw) To: linux-arm-kernel Enable pinctrl for phycore devices. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> --- arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts | 4 ++++ arch/arm/boot/dts/imx27-phytec-phycore-som.dts | 4 ++++ 2 files changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts index ad76d88..d4e1022 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts @@ -29,11 +29,15 @@ &uart1 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1_1 &pinctrl_uart1_rtscts_1>; status = "okay"; }; &uart2 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2_1 &pinctrl_uart2_rtscts_1>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dts b/arch/arm/boot/dts/imx27-phytec-phycore-som.dts index 648541a..1aafc0d 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycore-som.dts @@ -135,11 +135,15 @@ &fec { phy-reset-gpios = <&gpio3 30 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1_1>; status = "okay"; }; &i2c2 { clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2_1>; status = "okay"; at24 at 52 { -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v5 8/8] ARM: imx27: enable pinctrl 2013-10-24 15:38 [PATCH v5 0/8] ARM: imx27 pinctrl Markus Pargmann ` (6 preceding siblings ...) 2013-10-24 15:38 ` [PATCH v5 7/8] ARM: dts: imx27 phycore pinctrl Markus Pargmann @ 2013-10-24 15:38 ` Markus Pargmann 7 siblings, 0 replies; 11+ messages in thread From: Markus Pargmann @ 2013-10-24 15:38 UTC (permalink / raw) To: linux-arm-kernel Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Shawn Guo <shawn.guo@linaro.org> --- arch/arm/mach-imx/Kconfig | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index 29a8af6..58726d5 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -121,6 +121,8 @@ config SOC_IMX27 select IMX_HAVE_IOMUX_V1 select MACH_MX27 select MXC_AVIC + select PINCTRL + select PINCTRL_IMX27 config SOC_IMX31 bool -- 1.8.4.rc3 ^ permalink raw reply related [flat|nested] 11+ messages in thread
end of thread, other threads:[~2013-10-28 7:57 UTC | newest] Thread overview: 11+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2013-10-24 15:38 [PATCH v5 0/8] ARM: imx27 pinctrl Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 1/8] pinctrl: imx1 core driver Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 2/8] pinctrl: imx27: imx27 pincontrol driver Markus Pargmann 2013-10-24 19:46 ` Matt Sealey 2013-10-28 7:57 ` Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 3/8] ARM: dts: imx27 pin functions Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 4/8] ARM: dts: imx27 pinctrl Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 5/8] ARM: dts: imx27 phyCARD-S pinctrl Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 6/8] ARM: dts: imx27 phycore move uart1 to rdk Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 7/8] ARM: dts: imx27 phycore pinctrl Markus Pargmann 2013-10-24 15:38 ` [PATCH v5 8/8] ARM: imx27: enable pinctrl Markus Pargmann
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).