[PATCH v4 00/31] Armada 370/XP NAND support

[PATCH v4 00/31] Armada 370/XP NAND support

[Ezequiel Garcia]

Another version of the Armada 370/XP SoCs v3 patchset, addressing
all the feedback provided by Brian Norris.

Please see Documentation/mtd/nand/pxa3xx-nand.txt for specific details
about the controller and the driver.

Just as the last version, the bad block factory initial detection issue
is not addressed by this patchset, but support for it will be added in
a near future once we decide the proper roadmap. See here the discussion
about it:

  http://permalink.gmane.org/gmane.linux.drivers.mtd/49401

As usual patches 1-4, adding the clock infrastructure have already been merged
and will be dropped once this series can be based on v3.13-rc1.
I'm including them just for completeness.

Based in l2-mtd's master branch. Also, I've pushed a branch to our github
in case anyone wants to test it:

  https://github.com/MISL-EBU-System-SW/mainline-public/tree/l2-mtd/upstream-nand-v4

As per Jason Cooper's suggestion I'm Ccing devicetree mailing list, to get a review
on the small binding changes this patchset contains. If the devicetree people wants
us to just Cc you on the relevant patches, just let us know.

Of course, there's some room for improvements in this driver, and I'll probably
continue working on it. However, for now I'd like to focus in adding the strict
minimum amount of changes required to support the new SoC family and pospone any
improvements.

Thanks!

* Changes from v3 (feedback from Brian Norris)

  * Add binding documentation for the nand-flash-bbt DT property.

  * Expand in the documentation and in a comment the reason for
    setting the NAND_BBT_NO_OOB_BBM option.

  * Reworked the 'is_ready' completion handler. We still have
    two completions, but we've dropped the atomic_t type as
    now the variable is no longer accesed from interruption context.

  * Fixed the ecc.read_page() which lacked the max_bitflip return.

  * Reworked the ECC strength and size setting. This is important
    to allow the MTD layer to properly report on bitflip threshold
    situation.

  * Dropped an unused fifo_size state variable

  * Use '0' instead of the wrong '-1' when the extended command type
    doesn't matter or extended semantics are not supposed to be used.

* Changes from v2 (some minor fixes as per Huang's good feedback)

  * Add some more details to the commit log in patch
    "mtd: nand: pxa3xx: Early variant detection"

  * Add an empty line between variable declaration and function body
    in patch "mtd: nand: pxa3xx: Use chip->cmdfunc instead of the internal".

  * Fix a build break caused by incomplete variable replacement:
    "mtd: nand: pxa3xx: Replace host->page_size by mtd->writesize"

* Changes from v1

Aside from several changes based in Brian's feedback, the main changes
from v1 are:

  * The controller's clock source is now fully modeled, see patche 1 to 4.
    Of course, none of those patches should be taken through the mtd
    subsystem, but I'm adding them here for completeness.

  * The chip's cmdfunc() is now independently implemented in each SoC variant.
    The rationale behind this decision is that 'chunked' I/O is the only tested
    mode on the Armada370 variant, while the old 'vanilla' I/O is the only
    tested mode on the PXA variant.

    So it's safer to have an implementation for each variant.

  * Added support for BCH-8, in other words: 8-bits of correction in a 512-byte
    region. This is obtained by using a data chunk size of 1024B, thus doubling
    the ECC BCH strength, as per this ECC engine mechanism.

  * The ECC layout in use, which must be set according to the page size and
    desired ECC strength is now strictly chosen to match only the tested
    combinations.

Ezequiel Garcia (31):
  clk: mvebu: Add Core Divider clock
  ARM: mvebu: Add Core Divider clock device-tree binding
  ARM: mvebu: Add a 2 GHz fixed-clock Armada 370/XP
  ARM: mvebu: Add the core-divider clock to Armada 370/XP
  mtd: nand: pxa3xx: devicetree binding update
  mtd: nand: pxa3xx: Add documentation about the controller
  mtd: nand: pxa3xx: Make config menu show supported platforms
  mtd: nand: pxa3xx: Prevent sub-page writes
  mtd: nand: pxa3xx: read_page() returns max_bitflips
  mtd: nand: pxa3xx: Early variant detection
  mtd: nand: pxa3xx: Use chip->cmdfunc instead of the internal
  mtd: nand: pxa3xx: Split FIFO size from to-be-read FIFO count
  mtd: nand: pxa3xx: Replace host->page_size by mtd->writesize
  mtd: nand: pxa3xx: Add a nice comment to pxa3xx_set_datasize()
  mtd: nand: pxa3xx: Use a completion to signal device ready
  mtd: nand: pxa3xx: Use waitfunc() to wait for the device to be ready
  mtd: nand: pxa3xx: Add bad block handling
  mtd: nand: pxa3xx: Add driver-specific ECC BCH support
  mtd: nand: pxa3xx: Clear cmd buffer #3 (NDCB3) on command start
  mtd: nand: pxa3xx: Add helper function to set page address
  mtd: nand: pxa3xx: Remove READ0 switch/case falltrough
  mtd: nand: pxa3xx: Split prepare_command_pool() in two stages
  mtd: nand: pxa3xx: Move the data buffer clean to
    prepare_start_command()
  mtd: nand: pxa3xx: Fix SEQIN column address set
  mtd: nand: pxa3xx: Add a read/write buffers markers
  mtd: nand: pxa3xx: Introduce multiple page I/O support
  mtd: nand: pxa3xx: Add multiple chunk write support
  mtd: nand: pxa3xx: Add ECC BCH correctable errors detection
  ARM: mvebu: Add support for NAND controller in Armada 370/XP
  ARM: mvebu: Enable NAND controller in Armada XP GP board
  ARM: mvebu: Enable NAND controller in Armada 370 Mirabox

 .../bindings/clock/mvebu-corediv-clock.txt         |  19 +
 .../devicetree/bindings/mtd/pxa3xx-nand.txt        |   6 +-
 Documentation/mtd/nand/pxa3xx-nand.txt             | 113 ++++
 arch/arm/boot/dts/armada-370-mirabox.dts           |  21 +
 arch/arm/boot/dts/armada-370-xp.dtsi               |  26 +
 arch/arm/boot/dts/armada-xp-gp.dts                 |   8 +
 drivers/clk/mvebu/Kconfig                          |   5 +
 drivers/clk/mvebu/Makefile                         |   1 +
 drivers/clk/mvebu/clk-corediv.c                    | 223 +++++++
 drivers/mtd/nand/Kconfig                           |   4 +-
 drivers/mtd/nand/pxa3xx_nand.c                     | 678 ++++++++++++++++-----
 include/linux/platform_data/mtd-nand-pxa3xx.h      |   3 +
 12 files changed, 965 insertions(+), 142 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
 create mode 100644 Documentation/mtd/nand/pxa3xx-nand.txt
 create mode 100644 drivers/clk/mvebu/clk-corediv.c

-- 
1.8.1.5

[PATCH v4 01/31] clk: mvebu: Add Core Divider clock

[Ezequiel Garcia]

This commit introduces a new group of clocks present in Armada 370/XP
SoCs (called "Core Divider" clocks) and add a provider for them.
The only clock supported for now is the NAND clock (ndclk), but the
infrastructure to add the rest is already set.

Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/clk/mvebu/Kconfig       |   5 +
 drivers/clk/mvebu/Makefile      |   1 +
 drivers/clk/mvebu/clk-corediv.c | 223 ++++++++++++++++++++++++++++++++++++++++
 3 files changed, 229 insertions(+)
 create mode 100644 drivers/clk/mvebu/clk-corediv.c

diff --git a/drivers/clk/mvebu/Kconfig b/drivers/clk/mvebu/Kconfig
index 0b0f3e7..c339b82 100644
--- a/drivers/clk/mvebu/Kconfig
+++ b/drivers/clk/mvebu/Kconfig
@@ -4,15 +4,20 @@ config MVEBU_CLK_COMMON
 config MVEBU_CLK_CPU
 	bool
 
+config MVEBU_CLK_COREDIV
+	bool
+
 config ARMADA_370_CLK
 	bool
 	select MVEBU_CLK_COMMON
 	select MVEBU_CLK_CPU
+	select MVEBU_CLK_COREDIV
 
 config ARMADA_XP_CLK
 	bool
 	select MVEBU_CLK_COMMON
 	select MVEBU_CLK_CPU
+	select MVEBU_CLK_COREDIV
 
 config DOVE_CLK
 	bool
diff --git a/drivers/clk/mvebu/Makefile b/drivers/clk/mvebu/Makefile
index 1c7e70c..21bbfb4 100644
--- a/drivers/clk/mvebu/Makefile
+++ b/drivers/clk/mvebu/Makefile
@@ -1,5 +1,6 @@
 obj-$(CONFIG_MVEBU_CLK_COMMON)	+= common.o
 obj-$(CONFIG_MVEBU_CLK_CPU) 	+= clk-cpu.o
+obj-$(CONFIG_MVEBU_CLK_COREDIV)	+= clk-corediv.o
 
 obj-$(CONFIG_ARMADA_370_CLK)	+= armada-370.o
 obj-$(CONFIG_ARMADA_XP_CLK)	+= armada-xp.o
diff --git a/drivers/clk/mvebu/clk-corediv.c b/drivers/clk/mvebu/clk-corediv.c
new file mode 100644
index 0000000..7162615
--- /dev/null
+++ b/drivers/clk/mvebu/clk-corediv.c
@@ -0,0 +1,223 @@
+/*
+ * MVEBU Core divider clock
+ *
+ * Copyright (C) 2013 Marvell
+ *
+ * Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/clk-provider.h>
+#include <linux/of_address.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include "common.h"
+
+#define CORE_CLK_DIV_RATIO_MASK		0xff
+#define CORE_CLK_DIV_RATIO_RELOAD	BIT(8)
+#define CORE_CLK_DIV_ENABLE_OFFSET	24
+#define CORE_CLK_DIV_RATIO_OFFSET	0x8
+
+struct clk_corediv_desc {
+	unsigned int mask;
+	unsigned int offset;
+	unsigned int fieldbit;
+};
+
+struct clk_corediv {
+	struct clk_hw hw;
+	void __iomem *reg;
+	struct clk_corediv_desc desc;
+	spinlock_t lock;
+};
+
+static struct clk_onecell_data clk_data;
+
+static const struct clk_corediv_desc mvebu_corediv_desc[] __initconst = {
+	{ .mask = 0x3f, .offset = 8, .fieldbit = 1 }, /* NAND clock */
+};
+
+#define to_corediv_clk(p) container_of(p, struct clk_corediv, hw)
+
+static int clk_corediv_is_enabled(struct clk_hw *hwclk)
+{
+	struct clk_corediv *corediv = to_corediv_clk(hwclk);
+	struct clk_corediv_desc *desc = &corediv->desc;
+	u32 enable_mask = BIT(desc->fieldbit) << CORE_CLK_DIV_ENABLE_OFFSET;
+
+	return !!(readl(corediv->reg) & enable_mask);
+}
+
+static int clk_corediv_enable(struct clk_hw *hwclk)
+{
+	struct clk_corediv *corediv = to_corediv_clk(hwclk);
+	struct clk_corediv_desc *desc = &corediv->desc;
+	unsigned long flags = 0;
+	u32 reg;
+
+	spin_lock_irqsave(&corediv->lock, flags);
+
+	reg = readl(corediv->reg);
+	reg |= (BIT(desc->fieldbit) << CORE_CLK_DIV_ENABLE_OFFSET);
+	writel(reg, corediv->reg);
+
+	spin_unlock_irqrestore(&corediv->lock, flags);
+
+	return 0;
+}
+
+static void clk_corediv_disable(struct clk_hw *hwclk)
+{
+	struct clk_corediv *corediv = to_corediv_clk(hwclk);
+	struct clk_corediv_desc *desc = &corediv->desc;
+	unsigned long flags = 0;
+	u32 reg;
+
+	spin_lock_irqsave(&corediv->lock, flags);
+
+	reg = readl(corediv->reg);
+	reg &= ~(BIT(desc->fieldbit) << CORE_CLK_DIV_ENABLE_OFFSET);
+	writel(reg, corediv->reg);
+
+	spin_unlock_irqrestore(&corediv->lock, flags);
+}
+
+static unsigned long clk_corediv_recalc_rate(struct clk_hw *hwclk,
+					 unsigned long parent_rate)
+{
+	struct clk_corediv *corediv = to_corediv_clk(hwclk);
+	struct clk_corediv_desc *desc = &corediv->desc;
+	u32 reg, div;
+
+	reg = readl(corediv->reg + CORE_CLK_DIV_RATIO_OFFSET);
+	div = (reg >> desc->offset) & desc->mask;
+	return parent_rate / div;
+}
+
+static long clk_corediv_round_rate(struct clk_hw *hwclk, unsigned long rate,
+			       unsigned long *parent_rate)
+{
+	/* Valid ratio are 1:4, 1:5, 1:6 and 1:8 */
+	u32 div;
+
+	div = *parent_rate / rate;
+	if (div < 4)
+		div = 4;
+	else if (div > 6)
+		div = 8;
+
+	return *parent_rate / div;
+}
+
+static int clk_corediv_set_rate(struct clk_hw *hwclk, unsigned long rate,
+			    unsigned long parent_rate)
+{
+	struct clk_corediv *corediv = to_corediv_clk(hwclk);
+	struct clk_corediv_desc *desc = &corediv->desc;
+	unsigned long flags = 0;
+	u32 reg, div;
+
+	div = parent_rate / rate;
+
+	spin_lock_irqsave(&corediv->lock, flags);
+
+	/* Write new divider to the divider ratio register */
+	reg = readl(corediv->reg + CORE_CLK_DIV_RATIO_OFFSET);
+	reg &= ~(desc->mask << desc->offset);
+	reg |= (div & desc->mask) << desc->offset;
+	writel(reg, corediv->reg + CORE_CLK_DIV_RATIO_OFFSET);
+
+	/* Set reload-force for this clock */
+	reg = readl(corediv->reg) | BIT(desc->fieldbit);
+	writel(reg, corediv->reg);
+
+	/* Now trigger the clock update */
+	reg = readl(corediv->reg) | CORE_CLK_DIV_RATIO_RELOAD;
+	writel(reg, corediv->reg);
+
+	/*
+	 * Wait for clocks to settle down, and then clear all the
+	 * ratios request and the reload request.
+	 */
+	udelay(1000);
+	reg &= ~(CORE_CLK_DIV_RATIO_MASK | CORE_CLK_DIV_RATIO_RELOAD);
+	writel(reg, corediv->reg);
+	udelay(1000);
+
+	spin_unlock_irqrestore(&corediv->lock, flags);
+
+	return 0;
+}
+
+static const struct clk_ops corediv_ops = {
+	.enable = clk_corediv_enable,
+	.disable = clk_corediv_disable,
+	.is_enabled = clk_corediv_is_enabled,
+	.recalc_rate = clk_corediv_recalc_rate,
+	.round_rate = clk_corediv_round_rate,
+	.set_rate = clk_corediv_set_rate,
+};
+
+static void __init mvebu_corediv_clk_init(struct device_node *node)
+{
+	struct clk_init_data init;
+	struct clk_corediv *corediv;
+	struct clk **clks;
+	void __iomem *base;
+	const char *parent_name;
+	const char *clk_name;
+	int i;
+
+	base = of_iomap(node, 0);
+	if (WARN_ON(!base))
+		return;
+
+	parent_name = of_clk_get_parent_name(node, 0);
+
+	clk_data.clk_num = ARRAY_SIZE(mvebu_corediv_desc);
+
+	/* clks holds the clock array */
+	clks = kcalloc(clk_data.clk_num, sizeof(struct clk *),
+				GFP_KERNEL);
+	if (WARN_ON(!clks))
+		goto err_unmap;
+	/* corediv holds the clock specific array */
+	corediv = kcalloc(clk_data.clk_num, sizeof(struct clk_corediv),
+				GFP_KERNEL);
+	if (WARN_ON(!corediv))
+		goto err_free_clks;
+
+	spin_lock_init(&corediv->lock);
+
+	for (i = 0; i < clk_data.clk_num; i++) {
+		of_property_read_string_index(node, "clock-output-names",
+					      i, &clk_name);
+		init.num_parents = 1;
+		init.parent_names = &parent_name;
+		init.name = clk_name;
+		init.ops = &corediv_ops;
+		init.flags = 0;
+
+		corediv[i].desc = mvebu_corediv_desc[i];
+		corediv[i].reg = base;
+		corediv[i].hw.init = &init;
+
+		clks[i] = clk_register(NULL, &corediv[i].hw);
+		WARN_ON(IS_ERR(clks[i]));
+	}
+
+	clk_data.clks = clks;
+	of_clk_add_provider(node, of_clk_src_onecell_get, &clk_data);
+	return;
+
+err_free_clks:
+	kfree(clks);
+err_unmap:
+	iounmap(base);
+}
+CLK_OF_DECLARE(mvebu_corediv_clk, "marvell,armada-370-corediv-clock",
+	       mvebu_corediv_clk_init);
-- 
1.8.1.5

[PATCH v4 02/31] ARM: mvebu: Add Core Divider clock device-tree binding

[Ezequiel Garcia]

The Armada 370/XP SoCs have a Core Divider clock providing
several clocks. For now, only the NAND clock is supported.

Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 .../devicetree/bindings/clock/mvebu-corediv-clock.txt | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt

diff --git a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
new file mode 100644
index 0000000..c62391f
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
@@ -0,0 +1,19 @@
+* Core Divider Clock bindings for Marvell MVEBU SoCs
+
+The following is a list of provided IDs and clock names on Armada 370/XP:
+ 0 = nand (NAND clock)
+
+Required properties:
+- compatible : must be "marvell,armada-370-corediv-clock"
+- reg : must be the register address of Core Divider control register
+- #clock-cells : from common clock binding; shall be set to 1
+- clocks : must be set to the parent's phandle
+
+Example:
+
+corediv_clk: corediv-clocks at 18740 {
+	compatible = "marvell,armada-370-corediv-clock";
+	reg = <0x18740 0xc>;
+	#clock-cells = <1>;
+	clocks = <&pll>;
+};
-- 
1.8.1.5

[PATCH v4 03/31] ARM: mvebu: Add a 2 GHz fixed-clock Armada 370/XP

[Ezequiel Garcia]

Armada 370/XP SoCs have a 2 GHz fixed PLL that is used to feed
other clocks. This commit adds a DT representation of this clock
through a fixed-clock compatible node.

Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 arch/arm/boot/dts/armada-370-xp.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi
index 1de2dae..924c721 100644
--- a/arch/arm/boot/dts/armada-370-xp.dtsi
+++ b/arch/arm/boot/dts/armada-370-xp.dtsi
@@ -252,4 +252,13 @@
 
 		};
 	};
+
+	clocks {
+		/* 2 GHz fixed main PLL */
+		mainpll: mainpll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <2000000000>;
+		};
+	};
  };
-- 
1.8.1.5

[PATCH v4 04/31] ARM: mvebu: Add the core-divider clock to Armada 370/XP

[Ezequiel Garcia]

The Armada 370/XP SoC has a clock provider called "Core Divider",
that is derived from a fixed 2 GHz PLL clock.

Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 arch/arm/boot/dts/armada-370-xp.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi
index 924c721..01e69fc 100644
--- a/arch/arm/boot/dts/armada-370-xp.dtsi
+++ b/arch/arm/boot/dts/armada-370-xp.dtsi
@@ -137,6 +137,14 @@
 				status = "disabled";
 			};
 
+			coredivclk: corediv-clock at 18740 {
+				compatible = "marvell,armada-370-corediv-clock";
+				reg = <0x18740 0xc>;
+				#clock-cells = <1>;
+				clocks = <&mainpll>;
+				clock-output-names = "nand";
+			};
+
 			timer at 20300 {
 				reg = <0x20300 0x30>, <0x21040 0x30>;
 				interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
-- 
1.8.1.5

[PATCH v4 05/31] mtd: nand: pxa3xx: devicetree binding update

[Ezequiel Garcia]

Since the driver supports the new compatible string, the binding
documentation must be updated to reflect it.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
index f1421e2..bed8390 100644
--- a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
@@ -2,7 +2,9 @@ PXA3xx NAND DT bindings
 
 Required properties:
 
- - compatible:		Should be "marvell,pxa3xx-nand"
+ - compatible:		Should be set to one of the following:
+			marvell,pxa3xx-nand
+			marvell,armada370-nand
  - reg: 		The register base for the controller
  - interrupts:		The interrupt to map
  - #address-cells:	Set to <1> if the node includes partitions
-- 
1.8.1.5

[PATCH v4 05/31] mtd: nand: pxa3xx: devicetree binding update

[Jason Cooper]

On Thu, Nov 07, 2013 at 12:17:09PM -0300, Ezequiel Garcia wrote:
> Since the driver supports the new compatible string, the binding
> documentation must be updated to reflect it.
> 
> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
> ---
>  Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt | 4 +++-
>  1 file changed, 3 insertions(+), 1 deletion(-)

Thanks for adding this, but please remember to update the Subject
string in the future.  Both this patch and the next one are changing the
Documentation/ portion of the tree, not drivers/.

And,

Acked-by: Jason Cooper <jason@lakedaemon.net>

thx,

Jason.

> diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
> index f1421e2..bed8390 100644
> --- a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
> +++ b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
> @@ -2,7 +2,9 @@ PXA3xx NAND DT bindings
>  
>  Required properties:
>  
> - - compatible:		Should be "marvell,pxa3xx-nand"
> + - compatible:		Should be set to one of the following:
> +			marvell,pxa3xx-nand
> +			marvell,armada370-nand
>   - reg: 		The register base for the controller
>   - interrupts:		The interrupt to map
>   - #address-cells:	Set to <1> if the node includes partitions
> -- 
> 1.8.1.5
> 

[PATCH v4 05/31] mtd: nand: pxa3xx: devicetree binding update

[Ezequiel Garcia]

On Thu, Nov 07, 2013 at 10:32:10AM -0500, Jason Cooper wrote:
> On Thu, Nov 07, 2013 at 12:17:09PM -0300, Ezequiel Garcia wrote:
> > Since the driver supports the new compatible string, the binding
> > documentation must be updated to reflect it.
> > 
> > Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
> > ---
> >  Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt | 4 +++-
> >  1 file changed, 3 insertions(+), 1 deletion(-)
> 
> Thanks for adding this, but please remember to update the Subject
> string in the future.  Both this patch and the next one are changing the
> Documentation/ portion of the tree, not drivers/.
> 

Come again?

You mean "[PATCH] Documentation: mtd: nand: Do this"

In that case: sorry, I do it differently on purpose, it looks better
to me (focus the affected driver), but maybe I'm wrong.

> And,
> 
> Acked-by: Jason Cooper <jason@lakedaemon.net>
> 

Thanks!

> thx,
> 
> Jason.
> 
> > diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
> > index f1421e2..bed8390 100644
> > --- a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
> > +++ b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
> > @@ -2,7 +2,9 @@ PXA3xx NAND DT bindings
> >  
> >  Required properties:
> >  
> > - - compatible:		Should be "marvell,pxa3xx-nand"
> > + - compatible:		Should be set to one of the following:
> > +			marvell,pxa3xx-nand
> > +			marvell,armada370-nand
> >   - reg: 		The register base for the controller
> >   - interrupts:		The interrupt to map
> >   - #address-cells:	Set to <1> if the node includes partitions
> > -- 
> > 1.8.1.5
> > 

-- 
Ezequiel Garc?a, Free Electrons
Embedded Linux, Kernel and Android Engineering
http://free-electrons.com

[PATCH v4 05/31] mtd: nand: pxa3xx: devicetree binding update

[Jason Cooper]

On Thu, Nov 07, 2013 at 01:41:33PM -0300, Ezequiel Garcia wrote:
> On Thu, Nov 07, 2013 at 10:32:10AM -0500, Jason Cooper wrote:
> > On Thu, Nov 07, 2013 at 12:17:09PM -0300, Ezequiel Garcia wrote:
> > > Since the driver supports the new compatible string, the binding
> > > documentation must be updated to reflect it.
> > > 
> > > Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
> > > ---
> > >  Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt | 4 +++-
> > >  1 file changed, 3 insertions(+), 1 deletion(-)
> > 
> > Thanks for adding this, but please remember to update the Subject
> > string in the future.  Both this patch and the next one are changing the
> > Documentation/ portion of the tree, not drivers/.
> > 
> 
> Come again?
> 
> You mean "[PATCH] Documentation: mtd: nand: Do this"
> 
> In that case: sorry, I do it differently on purpose, it looks better
> to me (focus the affected driver), but maybe I'm wrong.

but it makes it more difficult for devicetree binding reviewers to find
the patch in the series.  Perhaps having 'binding' in the Subject is
sufficient.  We'll see how things unfold over the next few days.

thx,

Jason.

[PATCH v4 06/31] mtd: nand: pxa3xx: Add documentation about the controller

[Ezequiel Garcia]

Given there's no public specification to this date, and in order
to capture some important details and singularities about the
controller let's document them once and for good.

Cc: linux-doc at vger.kernel.org
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 Documentation/mtd/nand/pxa3xx-nand.txt | 113 +++++++++++++++++++++++++++++++++
 drivers/mtd/nand/pxa3xx_nand.c         |   2 +
 2 files changed, 115 insertions(+)
 create mode 100644 Documentation/mtd/nand/pxa3xx-nand.txt

diff --git a/Documentation/mtd/nand/pxa3xx-nand.txt b/Documentation/mtd/nand/pxa3xx-nand.txt
new file mode 100644
index 0000000..00e601c
--- /dev/null
+++ b/Documentation/mtd/nand/pxa3xx-nand.txt
@@ -0,0 +1,113 @@
+
+About this document
+===================
+
+Some notes about Marvell's NAND controller available in PXA and Armada 370/XP
+SoC (aka NFCv1 and NFCv2), with an emphasis on the latter.
+
+NFCv2 controller background
+===========================
+
+The controller has a 2176 bytes FIFO buffer. Therefore, in order to support
+larger pages, I/O operations on 4 KiB and 8 KiB pages is done with a set of
+chunked transfers.
+
+For instance, if we choose a 2048 data chunk and set "BCH" ECC (see below)
+we'll have this layout in the pages:
+
+  ------------------------------------------------------------------------------
+  | 2048B data | 32B spare | 30B ECC || 2048B data | 32B spare | 30B ECC | ... |
+  ------------------------------------------------------------------------------
+
+The driver reads the data and spare portions independently and builds an internal
+buffer with this layout (in the 4 KiB page case):
+
+  ------------------------------------------
+  |     4096B data     |     64B spare     |
+  ------------------------------------------
+
+Also, for the READOOB command the driver disables the ECC and reads a 'spare + ECC'
+OOB, one per chunk read.
+
+  -------------------------------------------------------------------
+  |     4096B data     |  32B spare | 30B ECC | 32B spare | 30B ECC |
+  -------------------------------------------------------------------
+
+So, in order to achieve reading (for instance), we issue several READ0 commands
+(with some additional controller-specific magic) and read two chunks of 2080B
+(2048 data + 32 spare) each.
+The driver accomodates this data to expose the NAND core a contiguous buffer
+(4096 data + spare) or (4096 + spare + ECC + spare + ECC).
+
+ECC
+===
+
+The controller has built-in hardware ECC capabilities. In addition it is
+configurable between two modes: 1) Hamming, 2) BCH.
+
+Note that the actual BCH mode: BCH-4 or BCH-8 will depend on the way
+the controller is configured to transfer the data.
+
+In the BCH mode the ECC code will be calculated for each transfered chunk
+and expected to be located (when reading/programming) right after the spare
+bytes as the figure above shows.
+
+So, repeating the above scheme, a 2048B data chunk will be followed by 32B
+spare, and then the ECC controller will read/write the ECC code (30B in
+this case):
+
+  ------------------------------------
+  | 2048B data | 32B spare | 30B ECC |
+  ------------------------------------
+
+If the ECC mode is 'BCH' then the ECC is *always* 30 bytes long.
+If the ECC mode is 'Hamming' the ECC is 6 bytes long, for each 512B block.
+So in Hamming mode, a 2048B page will have a 24B ECC.
+
+Despite all of the above, the controller requires the driver to only read or
+write in multiples of 8-bytes, because the data buffer is 64-bits.
+
+OOB
+===
+
+Because of the above scheme, and because the "spare" OOB is really located in
+the middle of a page, spare OOB cannot be read or write independently of the
+data area. In other words, in order to read the OOB (aka READOOB), the entire
+page (aka READ0) has to be read.
+
+In the same sense, in order to write to the spare OOB the driver has to write
+an *entire* page.
+
+Factory bad blocks handling
+===========================
+
+Given the ECC BCH requires to layout the device's pages in a splitted
+data/OOB/data/OOB way, the controller has a view of the flash page that's
+different from the specified (aka the manufacturer's) view. In other words,
+
+Factory view:
+
+  -----------------------------------------------
+  |                    Data           |x  OOB   |
+  -----------------------------------------------
+
+Driver's view:
+
+  -----------------------------------------------
+  |      Data      | OOB |      Data   x  | OOB |
+  -----------------------------------------------
+
+It can be seen from the above, that the factory bad block marker must be
+searched within the 'data' region, and not in the usual OOB region.
+
+In addition, this means under regular usage the driver will write such
+position (since it belongs to the data region) and every used block is
+likely to be marked as bad.
+
+For this reason, marking the block as bad in the OOB is explicitly
+disabled by using the NAND_BBT_NO_OOB_BBM option in the driver. The rationale
+for this is that there's no point in marking a block as bad, because good
+blocks are also 'marked as bad' (in the OOB BBM sense) under normal usage.
+
+Instead, the drive relies in the bad block table alone, and should only perform
+the bad block scan on the very first time (when the device hasn't been used).
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 64c258e..3359047 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -7,6 +7,8 @@
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
+ *
+ * See Documentation/mtd/nand/pxa3xx-nand.txt for more details.
  */
 
 #include <linux/kernel.h>
-- 
1.8.1.5

[PATCH v4 06/31] mtd: nand: pxa3xx: Add documentation about the controller

[Brian Norris]

On Thu, Nov 07, 2013 at 12:17:10PM -0300, Ezequiel Garcia wrote:
> Given there's no public specification to this date, and in order
> to capture some important details and singularities about the
> controller let's document them once and for good.

Made a few small tweaks for spelling and such (see the following diff)
and pushed patches 5 through 14 to l2-mtd.git/next.

Thanks,
Brian

diff --git a/Documentation/mtd/nand/pxa3xx-nand.txt b/Documentation/mtd/nand/pxa3xx-nand.txt
index 00e601c..840fd41 100644
--- a/Documentation/mtd/nand/pxa3xx-nand.txt
+++ b/Documentation/mtd/nand/pxa3xx-nand.txt
@@ -36,7 +36,7 @@ OOB, one per chunk read.
 So, in order to achieve reading (for instance), we issue several READ0 commands
 (with some additional controller-specific magic) and read two chunks of 2080B
 (2048 data + 32 spare) each.
-The driver accomodates this data to expose the NAND core a contiguous buffer
+The driver accommodates this data to expose the NAND core a contiguous buffer
 (4096 data + spare) or (4096 + spare + ECC + spare + ECC).
 
 ECC
@@ -81,7 +81,7 @@ an *entire* page.
 Factory bad blocks handling
 ===========================
 
-Given the ECC BCH requires to layout the device's pages in a splitted
+Given the ECC BCH requires to layout the device's pages in a split
 data/OOB/data/OOB way, the controller has a view of the flash page that's
 different from the specified (aka the manufacturer's) view. In other words,
 
@@ -109,5 +109,5 @@ disabled by using the NAND_BBT_NO_OOB_BBM option in the driver. The rationale
 for this is that there's no point in marking a block as bad, because good
 blocks are also 'marked as bad' (in the OOB BBM sense) under normal usage.
 
-Instead, the drive relies in the bad block table alone, and should only perform
+Instead, the driver relies on the bad block table alone, and should only perform
 the bad block scan on the very first time (when the device hasn't been used).

[PATCH v4 06/31] mtd: nand: pxa3xx: Add documentation about the controller

[Ezequiel Garcia]

On Thu, Nov 14, 2013 at 11:00:04AM -0800, Brian Norris wrote:
> On Thu, Nov 07, 2013 at 12:17:10PM -0300, Ezequiel Garcia wrote:
> > Given there's no public specification to this date, and in order
> > to capture some important details and singularities about the
> > controller let's document them once and for good.
> 
> Made a few small tweaks for spelling and such (see the following diff)
> and pushed patches 5 through 14 to l2-mtd.git/next.
> 

The below diff looks ok. I had to rework a few patches after the
completion patch rework, and I'm running some tests.

I'll submit the series as soon as the tests are done.

> Thanks,
> Brian
> 
> diff --git a/Documentation/mtd/nand/pxa3xx-nand.txt b/Documentation/mtd/nand/pxa3xx-nand.txt
> index 00e601c..840fd41 100644
> --- a/Documentation/mtd/nand/pxa3xx-nand.txt
> +++ b/Documentation/mtd/nand/pxa3xx-nand.txt
> @@ -36,7 +36,7 @@ OOB, one per chunk read.
>  So, in order to achieve reading (for instance), we issue several READ0 commands
>  (with some additional controller-specific magic) and read two chunks of 2080B
>  (2048 data + 32 spare) each.
> -The driver accomodates this data to expose the NAND core a contiguous buffer
> +The driver accommodates this data to expose the NAND core a contiguous buffer
>  (4096 data + spare) or (4096 + spare + ECC + spare + ECC).
>  
>  ECC
> @@ -81,7 +81,7 @@ an *entire* page.
>  Factory bad blocks handling
>  ===========================
>  
> -Given the ECC BCH requires to layout the device's pages in a splitted
> +Given the ECC BCH requires to layout the device's pages in a split
>  data/OOB/data/OOB way, the controller has a view of the flash page that's
>  different from the specified (aka the manufacturer's) view. In other words,
>  
> @@ -109,5 +109,5 @@ disabled by using the NAND_BBT_NO_OOB_BBM option in the driver. The rationale
>  for this is that there's no point in marking a block as bad, because good
>  blocks are also 'marked as bad' (in the OOB BBM sense) under normal usage.
>  
> -Instead, the drive relies in the bad block table alone, and should only perform
> +Instead, the driver relies on the bad block table alone, and should only perform
>  the bad block scan on the very first time (when the device hasn't been used).

-- 
Ezequiel Garc?a, Free Electrons
Embedded Linux, Kernel and Android Engineering
http://free-electrons.com

[PATCH v4 07/31] mtd: nand: pxa3xx: Make config menu show supported platforms

[Ezequiel Garcia]

Since we have now support for the NFCv2 controller found on
Armada 370/XP platforms.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/Kconfig | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 93ae6a6..942ef28 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -326,11 +326,11 @@ config MTD_NAND_ATMEL
 	  on Atmel AT91 and AVR32 processors.
 
 config MTD_NAND_PXA3xx
-	tristate "Support for NAND flash devices on PXA3xx"
+	tristate "NAND support on PXA3xx and Armada 370/XP"
 	depends on PXA3xx || ARCH_MMP || PLAT_ORION
 	help
 	  This enables the driver for the NAND flash device found on
-	  PXA3xx processors
+	  PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
 
 config MTD_NAND_SLC_LPC32XX
 	tristate "NXP LPC32xx SLC Controller"
-- 
1.8.1.5

[PATCH v4 08/31] mtd: nand: pxa3xx: Prevent sub-page writes

[Ezequiel Garcia]

The current driver doesn't support sub-page writing, so report
that to the NAND core.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 3359047..c578ca7 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -1145,6 +1145,7 @@ static int alloc_nand_resource(struct platform_device *pdev)
 		chip->read_byte		= pxa3xx_nand_read_byte;
 		chip->read_buf		= pxa3xx_nand_read_buf;
 		chip->write_buf		= pxa3xx_nand_write_buf;
+		chip->options		|= NAND_NO_SUBPAGE_WRITE;
 	}
 
 	spin_lock_init(&chip->controller->lock);
-- 
1.8.1.5

[PATCH v4 09/31] mtd: nand: pxa3xx: read_page() returns max_bitflips

[Ezequiel Garcia]

As per the ecc.read_page() prototype, we must return the maximum number
of bitflips that were corrected on any one region covering an ecc step.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index c578ca7..521d43e 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -751,6 +751,7 @@ static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
 {
 	struct pxa3xx_nand_host *host = mtd->priv;
 	struct pxa3xx_nand_info *info = host->info_data;
+	int max_bitflips = 0;
 
 	chip->read_buf(mtd, buf, mtd->writesize);
 	chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
@@ -758,6 +759,7 @@ static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
 	if (info->retcode == ERR_SBERR) {
 		switch (info->use_ecc) {
 		case 1:
+			max_bitflips = 1;
 			mtd->ecc_stats.corrected++;
 			break;
 		case 0:
@@ -776,7 +778,7 @@ static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
 			mtd->ecc_stats.failed++;
 	}
 
-	return 0;
+	return max_bitflips;
 }
 
 static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd)
-- 
1.8.1.5

[PATCH v4 10/31] mtd: nand: pxa3xx: Early variant detection

[Ezequiel Garcia]

In order to customize early settings depending on the detected SoC variant,
move the detection to be before the nand_chip struct filling.

In a follow-up patch, this change is needed to detect the variant *before*
the call to alloc_nand_resource(), which allows to set a different cmdfunc()
for each variant.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 48 +++++++++++++++++++++---------------------
 1 file changed, 24 insertions(+), 24 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 521d43e..c686adf 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -258,6 +258,29 @@ static struct pxa3xx_nand_flash builtin_flash_types[] = {
 /* convert nano-seconds to nand flash controller clock cycles */
 #define ns2cycle(ns, clk)	(int)((ns) * (clk / 1000000) / 1000)
 
+static struct of_device_id pxa3xx_nand_dt_ids[] = {
+	{
+		.compatible = "marvell,pxa3xx-nand",
+		.data       = (void *)PXA3XX_NAND_VARIANT_PXA,
+	},
+	{
+		.compatible = "marvell,armada370-nand",
+		.data       = (void *)PXA3XX_NAND_VARIANT_ARMADA370,
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(of, pxa3xx_nand_dt_ids);
+
+static enum pxa3xx_nand_variant
+pxa3xx_nand_get_variant(struct platform_device *pdev)
+{
+	const struct of_device_id *of_id =
+			of_match_device(pxa3xx_nand_dt_ids, &pdev->dev);
+	if (!of_id)
+		return PXA3XX_NAND_VARIANT_PXA;
+	return (enum pxa3xx_nand_variant)of_id->data;
+}
+
 static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host,
 				   const struct pxa3xx_nand_timing *t)
 {
@@ -1125,6 +1148,7 @@ static int alloc_nand_resource(struct platform_device *pdev)
 		return -ENOMEM;
 
 	info->pdev = pdev;
+	info->variant = pxa3xx_nand_get_variant(pdev);
 	for (cs = 0; cs < pdata->num_cs; cs++) {
 		mtd = (struct mtd_info *)((unsigned int)&info[1] +
 		      (sizeof(*mtd) + sizeof(*host)) * cs);
@@ -1260,29 +1284,6 @@ static int pxa3xx_nand_remove(struct platform_device *pdev)
 	return 0;
 }
 
-static struct of_device_id pxa3xx_nand_dt_ids[] = {
-	{
-		.compatible = "marvell,pxa3xx-nand",
-		.data       = (void *)PXA3XX_NAND_VARIANT_PXA,
-	},
-	{
-		.compatible = "marvell,armada370-nand",
-		.data       = (void *)PXA3XX_NAND_VARIANT_ARMADA370,
-	},
-	{}
-};
-MODULE_DEVICE_TABLE(of, pxa3xx_nand_dt_ids);
-
-static enum pxa3xx_nand_variant
-pxa3xx_nand_get_variant(struct platform_device *pdev)
-{
-	const struct of_device_id *of_id =
-			of_match_device(pxa3xx_nand_dt_ids, &pdev->dev);
-	if (!of_id)
-		return PXA3XX_NAND_VARIANT_PXA;
-	return (enum pxa3xx_nand_variant)of_id->data;
-}
-
 static int pxa3xx_nand_probe_dt(struct platform_device *pdev)
 {
 	struct pxa3xx_nand_platform_data *pdata;
@@ -1339,7 +1340,6 @@ static int pxa3xx_nand_probe(struct platform_device *pdev)
 	}
 
 	info = platform_get_drvdata(pdev);
-	info->variant = pxa3xx_nand_get_variant(pdev);
 	probe_success = 0;
 	for (cs = 0; cs < pdata->num_cs; cs++) {
 		struct mtd_info *mtd = info->host[cs]->mtd;
-- 
1.8.1.5

[PATCH v4 11/31] mtd: nand: pxa3xx: Use chip->cmdfunc instead of the internal

[Ezequiel Garcia]

Whenever possible, it's always better to use the generic chip->cmdfunc
instead of the internal pxa3xx_nand_cmdfunc().
In this particular case, this will allow to have multiple cmdfunc()
implementations for different SoC variants.

Reviewed-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index c686adf..d153ba8 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -1015,14 +1015,18 @@ static void pxa3xx_nand_free_buff(struct pxa3xx_nand_info *info)
 static int pxa3xx_nand_sensing(struct pxa3xx_nand_info *info)
 {
 	struct mtd_info *mtd;
+	struct nand_chip *chip;
 	int ret;
+
 	mtd = info->host[info->cs]->mtd;
+	chip = mtd->priv;
+
 	/* use the common timing to make a try */
 	ret = pxa3xx_nand_config_flash(info, &builtin_flash_types[0]);
 	if (ret)
 		return ret;
 
-	pxa3xx_nand_cmdfunc(mtd, NAND_CMD_RESET, 0, 0);
+	chip->cmdfunc(mtd, NAND_CMD_RESET, 0, 0);
 	if (info->is_ready)
 		return 0;
 
-- 
1.8.1.5

[PATCH v4 12/31] mtd: nand: pxa3xx: Split FIFO size from to-be-read FIFO count

[Ezequiel Garcia]

Introduce a fifo_size field to represent the size of the controller's
FIFO buffer, and use it to distinguish that size from the amount
of data bytes to be read from the FIFO.

This is important to support devices with pages larger than the
controller's internal FIFO, that need to read the pages in FIFO-sized
chunks.

In particular, the current code is at least confusing, for it mixes
all the different sizes involved: FIFO size, page size and data size.

This commit starts the cleaning by removing the info->page_size field
that is not currently used. The host->page_size field should also
be removed and use always mtd->writesize instead. Follow up commits
will clean this up.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index d153ba8..6a69deb 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -201,8 +201,8 @@ struct pxa3xx_nand_info {
 	int			use_spare;	/* use spare ? */
 	int			is_ready;
 
-	unsigned int		page_size;	/* page size of attached chip */
-	unsigned int		data_size;	/* data size in FIFO */
+	unsigned int		fifo_size;	/* max. data size in the FIFO */
+	unsigned int		data_size;	/* data to be read from FIFO */
 	unsigned int		oob_size;
 	int 			retcode;
 
@@ -307,16 +307,15 @@ static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host,
 
 static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info)
 {
-	struct pxa3xx_nand_host *host = info->host[info->cs];
 	int oob_enable = info->reg_ndcr & NDCR_SPARE_EN;
 
-	info->data_size = host->page_size;
+	info->data_size = info->fifo_size;
 	if (!oob_enable) {
 		info->oob_size = 0;
 		return;
 	}
 
-	switch (host->page_size) {
+	switch (info->fifo_size) {
 	case 2048:
 		info->oob_size = (info->use_ecc) ? 40 : 64;
 		break;
@@ -933,9 +932,12 @@ static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info)
 	uint32_t ndcr = nand_readl(info, NDCR);
 
 	if (ndcr & NDCR_PAGE_SZ) {
+		/* Controller's FIFO size */
+		info->fifo_size = 2048;
 		host->page_size = 2048;
 		host->read_id_bytes = 4;
 	} else {
+		info->fifo_size = 512;
 		host->page_size = 512;
 		host->read_id_bytes = 2;
 	}
-- 
1.8.1.5

[PATCH v4 13/31] mtd: nand: pxa3xx: Replace host->page_size by mtd->writesize

[Ezequiel Garcia]

There's no need to privately store the device page size as it's
available in mtd structure field mtd->writesize.
Also, this removes the hardcoded page size value, leaving the
auto-detected value only.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 6a69deb..dd8a7cf 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -151,7 +151,6 @@ struct pxa3xx_nand_host {
 	void			*info_data;
 
 	/* page size of attached chip */
-	unsigned int		page_size;
 	int			use_ecc;
 	int			cs;
 
@@ -614,12 +613,12 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 			info->buf_start += mtd->writesize;
 
 		/* Second command setting for large pages */
-		if (host->page_size >= PAGE_CHUNK_SIZE)
+		if (mtd->writesize >= PAGE_CHUNK_SIZE)
 			info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8);
 
 	case NAND_CMD_SEQIN:
 		/* small page addr setting */
-		if (unlikely(host->page_size < PAGE_CHUNK_SIZE)) {
+		if (unlikely(mtd->writesize < PAGE_CHUNK_SIZE)) {
 			info->ndcb1 = ((page_addr & 0xFFFFFF) << 8)
 					| (column & 0xFF);
 
@@ -895,7 +894,6 @@ static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info,
 	}
 
 	/* calculate flash information */
-	host->page_size = f->page_size;
 	host->read_id_bytes = (f->page_size == 2048) ? 4 : 2;
 
 	/* calculate addressing information */
@@ -934,11 +932,9 @@ static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info)
 	if (ndcr & NDCR_PAGE_SZ) {
 		/* Controller's FIFO size */
 		info->fifo_size = 2048;
-		host->page_size = 2048;
 		host->read_id_bytes = 4;
 	} else {
 		info->fifo_size = 512;
-		host->page_size = 512;
 		host->read_id_bytes = 2;
 	}
 
@@ -1106,7 +1102,7 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
 	def = pxa3xx_flash_ids;
 KEEP_CONFIG:
 	chip->ecc.mode = NAND_ECC_HW;
-	chip->ecc.size = host->page_size;
+	chip->ecc.size = info->fifo_size;
 	chip->ecc.strength = 1;
 
 	if (info->reg_ndcr & NDCR_DWIDTH_M)
-- 
1.8.1.5

[PATCH v4 14/31] mtd: nand: pxa3xx: Add a nice comment to pxa3xx_set_datasize()

[Ezequiel Garcia]

Add a comment clarifying the use of pxa3xx_set_datasize() which is only
applicable on data read/write commands (i.e. commands with a data cycle,
such as READID, READ0, STATUS, etc.)

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index dd8a7cf..dd7df0e 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -304,6 +304,11 @@ static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host,
 	nand_writel(info, NDTR1CS0, ndtr1);
 }
 
+/*
+ * Set the data and OOB size, depending on the selected
+ * spare and ECC configuration.
+ * Only applicable to READ0, READOOB and PAGEPROG commands.
+ */
 static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info)
 {
 	int oob_enable = info->reg_ndcr & NDCR_SPARE_EN;
-- 
1.8.1.5

[PATCH v4 15/31] mtd: nand: pxa3xx: Use a completion to signal device ready

[Ezequiel Garcia]

The expected behavior of the waitfunc() NAND chip call is to wait
for the device to be READY (this is a standard chip line).
However, the current implementation does almost nothing, which opens
the possibility of issuing a command to a non-ready device.

Fix this by adding a new completion to wait for the ready event to arrive.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 35 +++++++++++++++++++++++------------
 1 file changed, 23 insertions(+), 12 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index dd7df0e..588b23a 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -37,6 +37,7 @@
 
 #include <linux/platform_data/mtd-nand-pxa3xx.h>
 
+#define NAND_DEV_READY_TIMEOUT  50
 #define	CHIP_DELAY_TIMEOUT	(2 * HZ/10)
 #define NAND_STOP_DELAY		(2 * HZ/50)
 #define PAGE_CHUNK_SIZE		(2048)
@@ -168,7 +169,7 @@ struct pxa3xx_nand_info {
 	struct clk		*clk;
 	void __iomem		*mmio_base;
 	unsigned long		mmio_phys;
-	struct completion	cmd_complete;
+	struct completion	cmd_complete, dev_ready;
 
 	unsigned int 		buf_start;
 	unsigned int		buf_count;
@@ -480,7 +481,7 @@ static void start_data_dma(struct pxa3xx_nand_info *info)
 static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
 {
 	struct pxa3xx_nand_info *info = devid;
-	unsigned int status, is_completed = 0;
+	unsigned int status, is_completed = 0, is_ready = 0;
 	unsigned int ready, cmd_done;
 
 	if (info->cs == 0) {
@@ -516,8 +517,8 @@ static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
 		is_completed = 1;
 	}
 	if (status & ready) {
-		info->is_ready = 1;
 		info->state = STATE_READY;
+		is_ready = 1;
 	}
 
 	if (status & NDSR_WRCMDREQ) {
@@ -546,6 +547,8 @@ static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
 	nand_writel(info, NDSR, status);
 	if (is_completed)
 		complete(&info->cmd_complete);
+	if (is_ready)
+		complete(&info->dev_ready);
 NORMAL_IRQ_EXIT:
 	return IRQ_HANDLED;
 }
@@ -576,7 +579,6 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 	info->oob_size		= 0;
 	info->use_ecc		= 0;
 	info->use_spare		= 1;
-	info->is_ready		= 0;
 	info->retcode		= ERR_NONE;
 	if (info->cs != 0)
 		info->ndcb0 = NDCB0_CSEL;
@@ -749,6 +751,8 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
 	exec_cmd = prepare_command_pool(info, command, column, page_addr);
 	if (exec_cmd) {
 		init_completion(&info->cmd_complete);
+		init_completion(&info->dev_ready);
+		info->is_ready = 0;
 		pxa3xx_nand_start(info);
 
 		ret = wait_for_completion_timeout(&info->cmd_complete,
@@ -863,21 +867,28 @@ static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
 {
 	struct pxa3xx_nand_host *host = mtd->priv;
 	struct pxa3xx_nand_info *info = host->info_data;
+	int ret;
+
+	/* Need to wait? */
+	if (!info->is_ready) {
+		ret = wait_for_completion_timeout(&info->dev_ready,
+				CHIP_DELAY_TIMEOUT);
+		if (!ret) {
+			dev_err(&info->pdev->dev, "Ready time out!!!\n");
+			return NAND_STATUS_FAIL;
+		}
+		info->is_ready = 1;
+	}
 
 	/* pxa3xx_nand_send_command has waited for command complete */
 	if (this->state == FL_WRITING || this->state == FL_ERASING) {
 		if (info->retcode == ERR_NONE)
 			return 0;
-		else {
-			/*
-			 * any error make it return 0x01 which will tell
-			 * the caller the erase and write fail
-			 */
-			return 0x01;
-		}
+		else
+			return NAND_STATUS_FAIL;
 	}
 
-	return 0;
+	return NAND_STATUS_READY;
 }
 
 static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info,
-- 
1.8.1.5

[PATCH v4 15/31] mtd: nand: pxa3xx: Use a completion to signal device ready

[Brian Norris]

On Thu, Nov 07, 2013 at 12:17:19PM -0300, Ezequiel Garcia wrote:
> --- a/drivers/mtd/nand/pxa3xx_nand.c
> +++ b/drivers/mtd/nand/pxa3xx_nand.c
> @@ -863,21 +867,28 @@ static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
>  {
>  	struct pxa3xx_nand_host *host = mtd->priv;
>  	struct pxa3xx_nand_info *info = host->info_data;
> +	int ret;
> +
> +	/* Need to wait? */
> +	if (!info->is_ready) {
> +		ret = wait_for_completion_timeout(&info->dev_ready,
> +				CHIP_DELAY_TIMEOUT);
> +		if (!ret) {
> +			dev_err(&info->pdev->dev, "Ready time out!!!\n");
> +			return NAND_STATUS_FAIL;
> +		}
> +		info->is_ready = 1;

Shouldn't the is_ready=1 line to be above the if (!ret) condition? I
think you want to set is_ready=1 in either case (success or timeout).
With this code, any timeout will cause subsequent waitfunc()'s to block,
even if they are never going to catch an interrupt.

I think this kind of mistake is easier to make now, since the 'is_ready'
field isn't properly descriptive any more. It doesn't represent "is the
device ready"; it represents "is there a pending command on which I need
to wait". (I don't care if you change the name; I'm just pointing this
out.)

> +	}
>  

I think all the other patches up to this one are good. I may push them
to l2-mtd.git now, unless you object.

Brian

[PATCH v4 15/31] mtd: nand: pxa3xx: Use a completion to signal device ready

[Ezequiel Garcia]

Brian,

On Thu, Nov 14, 2013 at 10:39:23AM -0800, Brian Norris wrote:
> On Thu, Nov 07, 2013 at 12:17:19PM -0300, Ezequiel Garcia wrote:
> > --- a/drivers/mtd/nand/pxa3xx_nand.c
> > +++ b/drivers/mtd/nand/pxa3xx_nand.c
> > @@ -863,21 +867,28 @@ static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
> >  {
> >  	struct pxa3xx_nand_host *host = mtd->priv;
> >  	struct pxa3xx_nand_info *info = host->info_data;
> > +	int ret;
> > +
> > +	/* Need to wait? */
> > +	if (!info->is_ready) {
> > +		ret = wait_for_completion_timeout(&info->dev_ready,
> > +				CHIP_DELAY_TIMEOUT);
> > +		if (!ret) {
> > +			dev_err(&info->pdev->dev, "Ready time out!!!\n");
> > +			return NAND_STATUS_FAIL;
> > +		}
> > +		info->is_ready = 1;
> 
> Shouldn't the is_ready=1 line to be above the if (!ret) condition? I
> think you want to set is_ready=1 in either case (success or timeout).
> With this code, any timeout will cause subsequent waitfunc()'s to block,
> even if they are never going to catch an interrupt.
> 

Yes, good catch!

> I think this kind of mistake is easier to make now, since the 'is_ready'
> field isn't properly descriptive any more. It doesn't represent "is the
> device ready"; it represents "is there a pending command on which I need
> to wait". (I don't care if you change the name; I'm just pointing this
> out.)
> 

Yes, I agree. Maybe, "need_wait" or something like that would fit
better. Let me submit a new patch for this one.

> > +	}
> >  
> 
> I think all the other patches up to this one are good. I may push them
> to l2-mtd.git now, unless you object.
> 

Great, thanks a lot for reviewing and for all the feedback!
-- 
Ezequiel Garc?a, Free Electrons
Embedded Linux, Kernel and Android Engineering
http://free-electrons.com

[PATCH v4 16/31] mtd: nand: pxa3xx: Use waitfunc() to wait for the device to be ready

[Ezequiel Garcia]

In pxa3xx_nand_sensing() instead of simply using info->is_ready
after issuing a command, the correct way of checking is to wait
for the device to be ready through the chip's waitfunc().

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 588b23a..6997a25 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -1041,10 +1041,11 @@ static int pxa3xx_nand_sensing(struct pxa3xx_nand_info *info)
 		return ret;
 
 	chip->cmdfunc(mtd, NAND_CMD_RESET, 0, 0);
-	if (info->is_ready)
-		return 0;
+	ret = chip->waitfunc(mtd, chip);
+	if (ret & NAND_STATUS_FAIL)
+		return -ENODEV;
 
-	return -ENODEV;
+	return 0;
 }
 
 static int pxa3xx_nand_scan(struct mtd_info *mtd)
-- 
1.8.1.5

[PATCH v4 17/31] mtd: nand: pxa3xx: Add bad block handling

[Ezequiel Garcia]

Add support for flash-based bad block table using Marvell's
custom in-flash bad block table layout. The support is enabled
a 'flash_bbt' platform data or device tree parameter.

While at it, update the binding document to reflect this driver
supports the property.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 .../devicetree/bindings/mtd/pxa3xx-nand.txt        |  2 ++
 drivers/mtd/nand/pxa3xx_nand.c                     | 37 ++++++++++++++++++++++
 include/linux/platform_data/mtd-nand-pxa3xx.h      |  3 ++
 3 files changed, 42 insertions(+)

diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
index bed8390..86e0a56 100644
--- a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
@@ -15,6 +15,8 @@ Optional properties:
  - marvell,nand-keep-config:	Set to keep the NAND controller config as set
 				by the bootloader
  - num-cs:			Number of chipselect lines to usw
+ - nand-on-flash-bbt: 		boolean to enable on flash bbt option if
+				not present false
 
 Example:
 
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 6997a25..5b703ab 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -26,6 +26,7 @@
 #include <linux/slab.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_mtd.h>
 
 #if defined(CONFIG_ARCH_PXA) || defined(CONFIG_ARCH_MMP)
 #define ARCH_HAS_DMA
@@ -241,6 +242,29 @@ static struct pxa3xx_nand_flash builtin_flash_types[] = {
 { "256MiB 16-bit", 0xba20,  64, 2048, 16, 16, 2048, &timing[3] },
 };
 
+static u8 bbt_pattern[] = {'M', 'V', 'B', 'b', 't', '0' };
+static u8 bbt_mirror_pattern[] = {'1', 't', 'b', 'B', 'V', 'M' };
+
+static struct nand_bbt_descr bbt_main_descr = {
+	.options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+		| NAND_BBT_2BIT | NAND_BBT_VERSION,
+	.offs =	8,
+	.len = 6,
+	.veroffs = 14,
+	.maxblocks = 8,		/* Last 8 blocks in each chip */
+	.pattern = bbt_pattern
+};
+
+static struct nand_bbt_descr bbt_mirror_descr = {
+	.options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+		| NAND_BBT_2BIT | NAND_BBT_VERSION,
+	.offs =	8,
+	.len = 6,
+	.veroffs = 14,
+	.maxblocks = 8,		/* Last 8 blocks in each chip */
+	.pattern = bbt_mirror_pattern
+};
+
 /* Define a default flash type setting serve as flash detecting only */
 #define DEFAULT_FLASH_TYPE (&builtin_flash_types[0])
 
@@ -1127,6 +1151,18 @@ KEEP_CONFIG:
 
 	if (nand_scan_ident(mtd, 1, def))
 		return -ENODEV;
+
+	if (pdata->flash_bbt) {
+		/*
+		 * We'll use a bad block table stored in-flash and don't
+		 * allow writing the bad block marker to the flash.
+		 */
+		chip->bbt_options |= NAND_BBT_USE_FLASH |
+				     NAND_BBT_NO_OOB_BBM;
+		chip->bbt_td = &bbt_main_descr;
+		chip->bbt_md = &bbt_mirror_descr;
+	}
+
 	/* calculate addressing information */
 	if (mtd->writesize >= 2048)
 		host->col_addr_cycles = 2;
@@ -1322,6 +1358,7 @@ static int pxa3xx_nand_probe_dt(struct platform_device *pdev)
 	if (of_get_property(np, "marvell,nand-keep-config", NULL))
 		pdata->keep_config = 1;
 	of_property_read_u32(np, "num-cs", &pdata->num_cs);
+	pdata->flash_bbt = of_get_nand_on_flash_bbt(np);
 
 	pdev->dev.platform_data = pdata;
 
diff --git a/include/linux/platform_data/mtd-nand-pxa3xx.h b/include/linux/platform_data/mtd-nand-pxa3xx.h
index ffb8019..a941471 100644
--- a/include/linux/platform_data/mtd-nand-pxa3xx.h
+++ b/include/linux/platform_data/mtd-nand-pxa3xx.h
@@ -55,6 +55,9 @@ struct pxa3xx_nand_platform_data {
 	/* indicate how many chip selects will be used */
 	int	num_cs;
 
+	/* use an flash-based bad block table */
+	bool	flash_bbt;
+
 	const struct mtd_partition		*parts[NUM_CHIP_SELECT];
 	unsigned int				nr_parts[NUM_CHIP_SELECT];
 
-- 
1.8.1.5

[PATCH v4 18/31] mtd: nand: pxa3xx: Add driver-specific ECC BCH support

[Ezequiel Garcia]

This commit adds the BCH ECC support available in NFCv2 controller.
Depending on the detected required strength the respective ECC layout
is selected.

This commit adds an empty ECC layout, since support to access large
pages is first required. Once that support is added, a proper ECC
layout will be added as well.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 86 +++++++++++++++++++++++++++++++++---------
 1 file changed, 69 insertions(+), 17 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 5b703ab..4d950dd 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -58,6 +58,7 @@
 #define NDPCR		(0x18) /* Page Count Register */
 #define NDBDR0		(0x1C) /* Bad Block Register 0 */
 #define NDBDR1		(0x20) /* Bad Block Register 1 */
+#define NDECCCTRL	(0x28) /* ECC control */
 #define NDDB		(0x40) /* Data Buffer */
 #define NDCB0		(0x48) /* Command Buffer0 */
 #define NDCB1		(0x4C) /* Command Buffer1 */
@@ -198,6 +199,7 @@ struct pxa3xx_nand_info {
 
 	int			cs;
 	int			use_ecc;	/* use HW ECC ? */
+	int			ecc_bch;	/* using BCH ECC? */
 	int			use_dma;	/* use DMA ? */
 	int			use_spare;	/* use spare ? */
 	int			is_ready;
@@ -205,6 +207,8 @@ struct pxa3xx_nand_info {
 	unsigned int		fifo_size;	/* max. data size in the FIFO */
 	unsigned int		data_size;	/* data to be read from FIFO */
 	unsigned int		oob_size;
+	unsigned int		spare_size;
+	unsigned int		ecc_size;
 	int 			retcode;
 
 	/* cached register value */
@@ -339,19 +343,12 @@ static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info)
 	int oob_enable = info->reg_ndcr & NDCR_SPARE_EN;
 
 	info->data_size = info->fifo_size;
-	if (!oob_enable) {
-		info->oob_size = 0;
+	if (!oob_enable)
 		return;
-	}
 
-	switch (info->fifo_size) {
-	case 2048:
-		info->oob_size = (info->use_ecc) ? 40 : 64;
-		break;
-	case 512:
-		info->oob_size = (info->use_ecc) ? 8 : 16;
-		break;
-	}
+	info->oob_size = info->spare_size;
+	if (!info->use_ecc)
+		info->oob_size += info->ecc_size;
 }
 
 /**
@@ -366,10 +363,15 @@ static void pxa3xx_nand_start(struct pxa3xx_nand_info *info)
 
 	ndcr = info->reg_ndcr;
 
-	if (info->use_ecc)
+	if (info->use_ecc) {
 		ndcr |= NDCR_ECC_EN;
-	else
+		if (info->ecc_bch)
+			nand_writel(info, NDECCCTRL, 0x1);
+	} else {
 		ndcr &= ~NDCR_ECC_EN;
+		if (info->ecc_bch)
+			nand_writel(info, NDECCCTRL, 0x0);
+	}
 
 	if (info->use_dma)
 		ndcr |= NDCR_DMA_EN;
@@ -1072,6 +1074,41 @@ static int pxa3xx_nand_sensing(struct pxa3xx_nand_info *info)
 	return 0;
 }
 
+static int pxa_ecc_init(struct pxa3xx_nand_info *info,
+			struct nand_ecc_ctrl *ecc,
+			int strength, int page_size)
+{
+	/*
+	 * We don't use strength here as the PXA variant
+	 * is used with non-ONFI compliant devices.
+	 */
+	if (page_size == 2048) {
+		info->spare_size = 40;
+		info->ecc_size = 24;
+		ecc->mode = NAND_ECC_HW;
+		ecc->size = 2048;
+		ecc->strength = 1;
+		return 1;
+
+	} else if (page_size == 512) {
+		info->spare_size = 8;
+		info->ecc_size = 8;
+		ecc->mode = NAND_ECC_HW;
+		ecc->size = 512;
+		ecc->strength = 1;
+		return 1;
+	}
+	return 0;
+}
+
+static int armada370_ecc_init(struct pxa3xx_nand_info *info,
+			      struct nand_ecc_ctrl *ecc,
+			      int strength, int page_size)
+{
+	/* Unimplemented yet */
+	return 0;
+}
+
 static int pxa3xx_nand_scan(struct mtd_info *mtd)
 {
 	struct pxa3xx_nand_host *host = mtd->priv;
@@ -1142,13 +1179,13 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd)
 	pxa3xx_flash_ids[1].name = NULL;
 	def = pxa3xx_flash_ids;
 KEEP_CONFIG:
-	chip->ecc.mode = NAND_ECC_HW;
-	chip->ecc.size = info->fifo_size;
-	chip->ecc.strength = 1;
-
 	if (info->reg_ndcr & NDCR_DWIDTH_M)
 		chip->options |= NAND_BUSWIDTH_16;
 
+	/* Device detection must be done with ECC disabled */
+	if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370)
+		nand_writel(info, NDECCCTRL, 0x0);
+
 	if (nand_scan_ident(mtd, 1, def))
 		return -ENODEV;
 
@@ -1163,6 +1200,21 @@ KEEP_CONFIG:
 		chip->bbt_md = &bbt_mirror_descr;
 	}
 
+	if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370)
+		ret = armada370_ecc_init(info, &chip->ecc,
+				   chip->ecc_strength_ds,
+				   mtd->writesize);
+	else
+		ret = pxa_ecc_init(info, &chip->ecc,
+				   chip->ecc_strength_ds,
+				   mtd->writesize);
+	if (!ret) {
+		dev_err(&info->pdev->dev,
+			"ECC strength %d at page size %d is not supported\n",
+			chip->ecc_strength_ds, mtd->writesize);
+		return -ENODEV;
+	}
+
 	/* calculate addressing information */
 	if (mtd->writesize >= 2048)
 		host->col_addr_cycles = 2;
-- 
1.8.1.5

[PATCH v4 19/31] mtd: nand: pxa3xx: Clear cmd buffer #3 (NDCB3) on command start

[Ezequiel Garcia]

Command buffer #3 is not properly cleared and it keeps the last
set value. Fix this by clearing when a command is setup.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 4d950dd..aa8768c 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -606,6 +606,7 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 	info->use_ecc		= 0;
 	info->use_spare		= 1;
 	info->retcode		= ERR_NONE;
+	info->ndcb3		= 0;
 	if (info->cs != 0)
 		info->ndcb0 = NDCB0_CSEL;
 	else
@@ -627,7 +628,6 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 	default:
 		info->ndcb1 = 0;
 		info->ndcb2 = 0;
-		info->ndcb3 = 0;
 		break;
 	}
 
-- 
1.8.1.5

[PATCH v4 20/31] mtd: nand: pxa3xx: Add helper function to set page address

[Ezequiel Garcia]

Let's simplify the code by first introducing a helper function
to set the page address, as done by the READ0, READOOB and SEQIN
commands.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 36 +++++++++++++++++++++---------------
 1 file changed, 21 insertions(+), 15 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index aa8768c..660427e 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -587,6 +587,26 @@ static inline int is_buf_blank(uint8_t *buf, size_t len)
 	return 1;
 }
 
+static void set_command_address(struct pxa3xx_nand_info *info,
+		unsigned int page_size, uint16_t column, int page_addr)
+{
+	/* small page addr setting */
+	if (page_size < PAGE_CHUNK_SIZE) {
+		info->ndcb1 = ((page_addr & 0xFFFFFF) << 8)
+				| (column & 0xFF);
+
+		info->ndcb2 = 0;
+	} else {
+		info->ndcb1 = ((page_addr & 0xFFFF) << 16)
+				| (column & 0xFFFF);
+
+		if (page_addr & 0xFF0000)
+			info->ndcb2 = (page_addr & 0xFF0000) >> 16;
+		else
+			info->ndcb2 = 0;
+	}
+}
+
 static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 		uint16_t column, int page_addr)
 {
@@ -650,22 +670,8 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 			info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8);
 
 	case NAND_CMD_SEQIN:
-		/* small page addr setting */
-		if (unlikely(mtd->writesize < PAGE_CHUNK_SIZE)) {
-			info->ndcb1 = ((page_addr & 0xFFFFFF) << 8)
-					| (column & 0xFF);
-
-			info->ndcb2 = 0;
-		} else {
-			info->ndcb1 = ((page_addr & 0xFFFF) << 16)
-					| (column & 0xFFFF);
-
-			if (page_addr & 0xFF0000)
-				info->ndcb2 = (page_addr & 0xFF0000) >> 16;
-			else
-				info->ndcb2 = 0;
-		}
 
+		set_command_address(info, mtd->writesize, column, page_addr);
 		info->buf_count = mtd->writesize + mtd->oobsize;
 		memset(info->data_buff, 0xFF, info->buf_count);
 
-- 
1.8.1.5

[PATCH v4 21/31] mtd: nand: pxa3xx: Remove READ0 switch/case falltrough

[Ezequiel Garcia]

READ0 and READOOB command preparation has a falltrough to SEQIN
case, where the command address is specified.
This is certainly confusing and makes the code less readable with
no added value. Let's remove it.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 660427e..552f92a 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -669,6 +669,11 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 		if (mtd->writesize >= PAGE_CHUNK_SIZE)
 			info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8);
 
+		set_command_address(info, mtd->writesize, column, page_addr);
+		info->buf_count = mtd->writesize + mtd->oobsize;
+		memset(info->data_buff, 0xFF, info->buf_count);
+		break;
+
 	case NAND_CMD_SEQIN:
 
 		set_command_address(info, mtd->writesize, column, page_addr);
-- 
1.8.1.5

[PATCH v4 22/31] mtd: nand: pxa3xx: Split prepare_command_pool() in two stages

[Ezequiel Garcia]

This commit splits the prepare_command_pool() function into two
stages: prepare_start_command() / prepare_set_command().

This is a preparation patch without any functionality changes,
and is meant to allow support for multiple page reading/writing
operations.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 44 ++++++++++++++++++++++++------------------
 1 file changed, 25 insertions(+), 19 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 552f92a..d3f3959 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -607,18 +607,8 @@ static void set_command_address(struct pxa3xx_nand_info *info,
 	}
 }
 
-static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
-		uint16_t column, int page_addr)
+static void prepare_start_command(struct pxa3xx_nand_info *info, int command)
 {
-	int addr_cycle, exec_cmd;
-	struct pxa3xx_nand_host *host;
-	struct mtd_info *mtd;
-
-	host = info->host[info->cs];
-	mtd = host->mtd;
-	addr_cycle = 0;
-	exec_cmd = 1;
-
 	/* reset data and oob column point to handle data */
 	info->buf_start		= 0;
 	info->buf_count		= 0;
@@ -627,10 +617,6 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 	info->use_spare		= 1;
 	info->retcode		= ERR_NONE;
 	info->ndcb3		= 0;
-	if (info->cs != 0)
-		info->ndcb0 = NDCB0_CSEL;
-	else
-		info->ndcb0 = 0;
 
 	switch (command) {
 	case NAND_CMD_READ0:
@@ -642,14 +628,32 @@ static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
 	case NAND_CMD_PARAM:
 		info->use_spare = 0;
 		break;
-	case NAND_CMD_SEQIN:
-		exec_cmd = 0;
-		break;
 	default:
 		info->ndcb1 = 0;
 		info->ndcb2 = 0;
 		break;
 	}
+}
+
+static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
+		uint16_t column, int page_addr)
+{
+	int addr_cycle, exec_cmd;
+	struct pxa3xx_nand_host *host;
+	struct mtd_info *mtd;
+
+	host = info->host[info->cs];
+	mtd = host->mtd;
+	addr_cycle = 0;
+	exec_cmd = 1;
+
+	if (info->cs != 0)
+		info->ndcb0 = NDCB0_CSEL;
+	else
+		info->ndcb0 = 0;
+
+	if (command == NAND_CMD_SEQIN)
+		exec_cmd = 0;
 
 	addr_cycle = NDCB0_ADDR_CYC(host->row_addr_cycles
 				    + host->col_addr_cycles);
@@ -784,8 +788,10 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
 		nand_writel(info, NDTR1CS0, info->ndtr1cs0);
 	}
 
+	prepare_start_command(info, command);
+
 	info->state = STATE_PREPARED;
-	exec_cmd = prepare_command_pool(info, command, column, page_addr);
+	exec_cmd = prepare_set_command(info, command, column, page_addr);
 	if (exec_cmd) {
 		init_completion(&info->cmd_complete);
 		init_completion(&info->dev_ready);
-- 
1.8.1.5

[PATCH v4 23/31] mtd: nand: pxa3xx: Move the data buffer clean to prepare_start_command()

[Ezequiel Garcia]

To allow future support of multiple page reading/writing, move the data
buffer clean out of prepare_set_command().

This is done to prevent the data buffer from being cleaned on every command
preparation, when a multiple command sequence is implemented to read/write
pages larger than the FIFO size (2 KiB).

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 21 ++++++++++++++++-----
 1 file changed, 16 insertions(+), 5 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index d3f3959..5f874a6 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -609,6 +609,9 @@ static void set_command_address(struct pxa3xx_nand_info *info,
 
 static void prepare_start_command(struct pxa3xx_nand_info *info, int command)
 {
+	struct pxa3xx_nand_host *host = info->host[info->cs];
+	struct mtd_info *mtd = host->mtd;
+
 	/* reset data and oob column point to handle data */
 	info->buf_start		= 0;
 	info->buf_count		= 0;
@@ -633,6 +636,19 @@ static void prepare_start_command(struct pxa3xx_nand_info *info, int command)
 		info->ndcb2 = 0;
 		break;
 	}
+
+	/*
+	 * If we are about to isse a read command, or about to set
+	 * the write address, then clean the data buffer.
+	 */
+	if (command == NAND_CMD_READ0 ||
+	    command == NAND_CMD_READOOB ||
+	    command == NAND_CMD_SEQIN) {
+
+		info->buf_count = mtd->writesize + mtd->oobsize;
+		memset(info->data_buff, 0xFF, info->buf_count);
+	}
+
 }
 
 static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
@@ -674,16 +690,11 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
 			info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8);
 
 		set_command_address(info, mtd->writesize, column, page_addr);
-		info->buf_count = mtd->writesize + mtd->oobsize;
-		memset(info->data_buff, 0xFF, info->buf_count);
 		break;
 
 	case NAND_CMD_SEQIN:
 
 		set_command_address(info, mtd->writesize, column, page_addr);
-		info->buf_count = mtd->writesize + mtd->oobsize;
-		memset(info->data_buff, 0xFF, info->buf_count);
-
 		break;
 
 	case NAND_CMD_PAGEPROG:
-- 
1.8.1.5

[PATCH v4 24/31] mtd: nand: pxa3xx: Fix SEQIN column address set

[Ezequiel Garcia]

This commit adds support page programming with a non-zero "column"
address setting. This is important to support OOB writing, through
command sequences such as:

  cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, ofs);
  write_buf(mtd, oob_buf, 6);
  cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 5f874a6..e09c901 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -694,7 +694,8 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
 
 	case NAND_CMD_SEQIN:
 
-		set_command_address(info, mtd->writesize, column, page_addr);
+		info->buf_start = column;
+		set_command_address(info, mtd->writesize, 0, page_addr);
 		break;
 
 	case NAND_CMD_PAGEPROG:
-- 
1.8.1.5

[PATCH v4 25/31] mtd: nand: pxa3xx: Add a read/write buffers markers

[Ezequiel Garcia]

In preparation to support multiple (aka chunked, aka splitted)
page I/O, this commit adds 'data_buff_pos' and 'oob_buff_pos' fields
to keep track of where the next read (or write) should be done.

This will allow multiple calls to handle_data_pio() to continue
the read (or write) operation.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 40 +++++++++++++++++++++++++++++-----------
 1 file changed, 29 insertions(+), 11 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index e09c901..59efd72 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -176,6 +176,8 @@ struct pxa3xx_nand_info {
 	unsigned int 		buf_start;
 	unsigned int		buf_count;
 	unsigned int		buf_size;
+	unsigned int		data_buff_pos;
+	unsigned int		oob_buff_pos;
 
 	/* DMA information */
 	int			drcmr_dat;
@@ -338,11 +340,12 @@ static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host,
  * spare and ECC configuration.
  * Only applicable to READ0, READOOB and PAGEPROG commands.
  */
-static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info)
+static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info,
+				struct mtd_info *mtd)
 {
 	int oob_enable = info->reg_ndcr & NDCR_SPARE_EN;
 
-	info->data_size = info->fifo_size;
+	info->data_size = mtd->writesize;
 	if (!oob_enable)
 		return;
 
@@ -430,26 +433,39 @@ static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
 
 static void handle_data_pio(struct pxa3xx_nand_info *info)
 {
+	unsigned int do_bytes = min(info->data_size, info->fifo_size);
+
 	switch (info->state) {
 	case STATE_PIO_WRITING:
-		__raw_writesl(info->mmio_base + NDDB, info->data_buff,
-				DIV_ROUND_UP(info->data_size, 4));
+		__raw_writesl(info->mmio_base + NDDB,
+			      info->data_buff + info->data_buff_pos,
+			      DIV_ROUND_UP(do_bytes, 4));
+
 		if (info->oob_size > 0)
-			__raw_writesl(info->mmio_base + NDDB, info->oob_buff,
-					DIV_ROUND_UP(info->oob_size, 4));
+			__raw_writesl(info->mmio_base + NDDB,
+				      info->oob_buff + info->oob_buff_pos,
+				      DIV_ROUND_UP(info->oob_size, 4));
 		break;
 	case STATE_PIO_READING:
-		__raw_readsl(info->mmio_base + NDDB, info->data_buff,
-				DIV_ROUND_UP(info->data_size, 4));
+		__raw_readsl(info->mmio_base + NDDB,
+			     info->data_buff + info->data_buff_pos,
+			     DIV_ROUND_UP(do_bytes, 4));
+
 		if (info->oob_size > 0)
-			__raw_readsl(info->mmio_base + NDDB, info->oob_buff,
-					DIV_ROUND_UP(info->oob_size, 4));
+			__raw_readsl(info->mmio_base + NDDB,
+				     info->oob_buff + info->oob_buff_pos,
+				     DIV_ROUND_UP(info->oob_size, 4));
 		break;
 	default:
 		dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
 				info->state);
 		BUG();
 	}
+
+	/* Update buffer pointers for multi-page read/write */
+	info->data_buff_pos += do_bytes;
+	info->oob_buff_pos += info->oob_size;
+	info->data_size -= do_bytes;
 }
 
 #ifdef ARCH_HAS_DMA
@@ -616,6 +632,8 @@ static void prepare_start_command(struct pxa3xx_nand_info *info, int command)
 	info->buf_start		= 0;
 	info->buf_count		= 0;
 	info->oob_size		= 0;
+	info->data_buff_pos	= 0;
+	info->oob_buff_pos	= 0;
 	info->use_ecc		= 0;
 	info->use_spare		= 1;
 	info->retcode		= ERR_NONE;
@@ -626,7 +644,7 @@ static void prepare_start_command(struct pxa3xx_nand_info *info, int command)
 	case NAND_CMD_PAGEPROG:
 		info->use_ecc = 1;
 	case NAND_CMD_READOOB:
-		pxa3xx_set_datasize(info);
+		pxa3xx_set_datasize(info, mtd);
 		break;
 	case NAND_CMD_PARAM:
 		info->use_spare = 0;
-- 
1.8.1.5

[PATCH v4 26/31] mtd: nand: pxa3xx: Introduce multiple page I/O support

[Ezequiel Garcia]

As preparation work to fully support large pages, this commit adds
the initial infrastructure to support splitted (aka chunked) I/O
operation. This commit adds support for read, and follow-up patches
will add write support.

When a read (aka READ0) command is issued, the driver loops issuing
the same command until all the requested data is transfered, changing
the 'extended' command field as needed.

For instance, if the driver is required to read a 4 KiB page, using a
chunk size of 2 KiB, the transaction is splitted in:
1. Monolithic read, first 2 KiB page chunk is read
2. Last naked read, second and last 2KiB page chunk is read

If ECC is enabled it is calculated on each chunk transfered and added
at a controller-fixed location after the data chunk that must be
spare area.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 182 ++++++++++++++++++++++++++++++++++++++---
 1 file changed, 172 insertions(+), 10 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 59efd72..51d90cc 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -103,6 +103,8 @@
 #define NDCB0_ST_ROW_EN         (0x1 << 26)
 #define NDCB0_AUTO_RS		(0x1 << 25)
 #define NDCB0_CSEL		(0x1 << 24)
+#define NDCB0_EXT_CMD_TYPE_MASK	(0x7 << 29)
+#define NDCB0_EXT_CMD_TYPE(x)	(((x) << 29) & NDCB0_EXT_CMD_TYPE_MASK)
 #define NDCB0_CMD_TYPE_MASK	(0x7 << 21)
 #define NDCB0_CMD_TYPE(x)	(((x) << 21) & NDCB0_CMD_TYPE_MASK)
 #define NDCB0_NC		(0x1 << 20)
@@ -113,6 +115,14 @@
 #define NDCB0_CMD1_MASK		(0xff)
 #define NDCB0_ADDR_CYC_SHIFT	(16)
 
+#define EXT_CMD_TYPE_DISPATCH	6 /* Command dispatch */
+#define EXT_CMD_TYPE_NAKED_RW	5 /* Naked read or Naked write */
+#define EXT_CMD_TYPE_READ	4 /* Read */
+#define EXT_CMD_TYPE_DISP_WR	4 /* Command dispatch with write */
+#define EXT_CMD_TYPE_FINAL	3 /* Final command */
+#define EXT_CMD_TYPE_LAST_RW	1 /* Last naked read/write */
+#define EXT_CMD_TYPE_MONO	0 /* Monolithic read/write */
+
 /* macros for registers read/write */
 #define nand_writel(info, off, val)	\
 	__raw_writel((val), (info)->mmio_base + (off))
@@ -206,8 +216,8 @@ struct pxa3xx_nand_info {
 	int			use_spare;	/* use spare ? */
 	int			is_ready;
 
-	unsigned int		fifo_size;	/* max. data size in the FIFO */
 	unsigned int		data_size;	/* data to be read from FIFO */
+	unsigned int		chunk_size;	/* split commands chunk size */
 	unsigned int		oob_size;
 	unsigned int		spare_size;
 	unsigned int		ecc_size;
@@ -271,6 +281,31 @@ static struct nand_bbt_descr bbt_mirror_descr = {
 	.pattern = bbt_mirror_pattern
 };
 
+static struct nand_ecclayout ecc_layout_4KB_bch4bit = {
+	.eccbytes = 64,
+	.eccpos = {
+		32,  33,  34,  35,  36,  37,  38,  39,
+		40,  41,  42,  43,  44,  45,  46,  47,
+		48,  49,  50,  51,  52,  53,  54,  55,
+		56,  57,  58,  59,  60,  61,  62,  63,
+		96,  97,  98,  99,  100, 101, 102, 103,
+		104, 105, 106, 107, 108, 109, 110, 111,
+		112, 113, 114, 115, 116, 117, 118, 119,
+		120, 121, 122, 123, 124, 125, 126, 127},
+	/* Bootrom looks in bytes 0 & 5 for bad blocks */
+	.oobfree = { {6, 26}, { 64, 32} }
+};
+
+static struct nand_ecclayout ecc_layout_4KB_bch8bit = {
+	.eccbytes = 128,
+	.eccpos = {
+		32,  33,  34,  35,  36,  37,  38,  39,
+		40,  41,  42,  43,  44,  45,  46,  47,
+		48,  49,  50,  51,  52,  53,  54,  55,
+		56,  57,  58,  59,  60,  61,  62,  63},
+	.oobfree = { }
+};
+
 /* Define a default flash type setting serve as flash detecting only */
 #define DEFAULT_FLASH_TYPE (&builtin_flash_types[0])
 
@@ -433,7 +468,7 @@ static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
 
 static void handle_data_pio(struct pxa3xx_nand_info *info)
 {
-	unsigned int do_bytes = min(info->data_size, info->fifo_size);
+	unsigned int do_bytes = min(info->data_size, info->chunk_size);
 
 	switch (info->state) {
 	case STATE_PIO_WRITING:
@@ -670,7 +705,7 @@ static void prepare_start_command(struct pxa3xx_nand_info *info, int command)
 }
 
 static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
-		uint16_t column, int page_addr)
+		int ext_cmd_type, uint16_t column, int page_addr)
 {
 	int addr_cycle, exec_cmd;
 	struct pxa3xx_nand_host *host;
@@ -703,9 +738,20 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
 		if (command == NAND_CMD_READOOB)
 			info->buf_start += mtd->writesize;
 
-		/* Second command setting for large pages */
-		if (mtd->writesize >= PAGE_CHUNK_SIZE)
+		/*
+		 * Multiple page read needs an 'extended command type' field,
+		 * which is either naked-read or last-read according to the
+		 * state.
+		 */
+		if (mtd->writesize == PAGE_CHUNK_SIZE) {
 			info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8);
+		} else if (mtd->writesize > PAGE_CHUNK_SIZE) {
+			info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8)
+					| NDCB0_LEN_OVRD
+					| NDCB0_EXT_CMD_TYPE(ext_cmd_type);
+			info->ndcb3 = info->chunk_size +
+				      info->oob_size;
+		}
 
 		set_command_address(info, mtd->writesize, column, page_addr);
 		break;
@@ -821,7 +867,8 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
 	prepare_start_command(info, command);
 
 	info->state = STATE_PREPARED;
-	exec_cmd = prepare_set_command(info, command, column, page_addr);
+	exec_cmd = prepare_set_command(info, command, 0, column, page_addr);
+
 	if (exec_cmd) {
 		init_completion(&info->cmd_complete);
 		init_completion(&info->dev_ready);
@@ -839,6 +886,93 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
 	info->state = STATE_IDLE;
 }
 
+static void armada370_nand_cmdfunc(struct mtd_info *mtd,
+				   const unsigned command,
+				   int column, int page_addr)
+{
+	struct pxa3xx_nand_host *host = mtd->priv;
+	struct pxa3xx_nand_info *info = host->info_data;
+	int ret, exec_cmd, ext_cmd_type;
+
+	/*
+	 * if this is a x16 device then convert the input
+	 * "byte" address into a "word" address appropriate
+	 * for indexing a word-oriented device
+	 */
+	if (info->reg_ndcr & NDCR_DWIDTH_M)
+		column /= 2;
+
+	/*
+	 * There may be different NAND chip hooked to
+	 * different chip select, so check whether
+	 * chip select has been changed, if yes, reset the timing
+	 */
+	if (info->cs != host->cs) {
+		info->cs = host->cs;
+		nand_writel(info, NDTR0CS0, info->ndtr0cs0);
+		nand_writel(info, NDTR1CS0, info->ndtr1cs0);
+	}
+
+	/* Select the extended command for the first command */
+	switch (command) {
+	case NAND_CMD_READ0:
+	case NAND_CMD_READOOB:
+		ext_cmd_type = EXT_CMD_TYPE_MONO;
+		break;
+	default:
+		ext_cmd_type = 0;
+	}
+
+	prepare_start_command(info, command);
+
+	/*
+	 * Prepare the "is ready" completion before starting a command
+	 * transaction sequence. If the command is not executed the
+	 * completion will be completed, see below.
+	 *
+	 * We can do that inside the loop because the command variable
+	 * is invariant and thus so is the exec_cmd.
+	 */
+	info->is_ready = 0;
+	init_completion(&info->dev_ready);
+	do {
+		info->state = STATE_PREPARED;
+		exec_cmd = prepare_set_command(info, command, ext_cmd_type,
+					       column, page_addr);
+		if (!exec_cmd) {
+			info->is_ready = 1;
+			complete(&info->dev_ready);
+			break;
+		}
+
+		init_completion(&info->cmd_complete);
+		pxa3xx_nand_start(info);
+
+		ret = wait_for_completion_timeout(&info->cmd_complete,
+				CHIP_DELAY_TIMEOUT);
+		if (!ret) {
+			dev_err(&info->pdev->dev, "Wait time out!!!\n");
+			/* Stop State Machine for next command cycle */
+			pxa3xx_nand_stop(info);
+			break;
+		}
+
+		/* Check if the sequence is complete */
+		if (info->data_size == 0)
+			break;
+
+		if (command == NAND_CMD_READ0 || command == NAND_CMD_READOOB) {
+			/* Last read: issue a 'last naked read' */
+			if (info->data_size == info->chunk_size)
+				ext_cmd_type = EXT_CMD_TYPE_LAST_RW;
+			else
+				ext_cmd_type = EXT_CMD_TYPE_NAKED_RW;
+		}
+	} while (1);
+
+	info->state = STATE_IDLE;
+}
+
 static int pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd,
 		struct nand_chip *chip, const uint8_t *buf, int oob_required)
 {
@@ -1020,13 +1154,14 @@ static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info)
 
 	if (ndcr & NDCR_PAGE_SZ) {
 		/* Controller's FIFO size */
-		info->fifo_size = 2048;
+		info->chunk_size = 2048;
 		host->read_id_bytes = 4;
 	} else {
-		info->fifo_size = 512;
+		info->chunk_size = 512;
 		host->read_id_bytes = 2;
 	}
 
+	/* Set an initial chunk size */
 	info->reg_ndcr = ndcr & ~NDCR_INT_MASK;
 	info->ndtr0cs0 = nand_readl(info, NDTR0CS0);
 	info->ndtr1cs0 = nand_readl(info, NDTR1CS0);
@@ -1130,6 +1265,7 @@ static int pxa_ecc_init(struct pxa3xx_nand_info *info,
 	 * is used with non-ONFI compliant devices.
 	 */
 	if (page_size == 2048) {
+		info->chunk_size = 2048;
 		info->spare_size = 40;
 		info->ecc_size = 24;
 		ecc->mode = NAND_ECC_HW;
@@ -1138,6 +1274,7 @@ static int pxa_ecc_init(struct pxa3xx_nand_info *info,
 		return 1;
 
 	} else if (page_size == 512) {
+		info->chunk_size = 512;
 		info->spare_size = 8;
 		info->ecc_size = 8;
 		ecc->mode = NAND_ECC_HW;
@@ -1152,7 +1289,28 @@ static int armada370_ecc_init(struct pxa3xx_nand_info *info,
 			      struct nand_ecc_ctrl *ecc,
 			      int strength, int page_size)
 {
-	/* Unimplemented yet */
+	if (strength == 4 && page_size == 4096) {
+		info->ecc_bch = 1;
+		info->chunk_size = 2048;
+		info->spare_size = 32;
+		info->ecc_size = 32;
+		ecc->mode = NAND_ECC_HW;
+		ecc->size = info->chunk_size;
+		ecc->layout = &ecc_layout_4KB_bch4bit;
+		ecc->strength = 16;
+		return 1;
+
+	} else if (strength == 8 && page_size == 4096) {
+		info->ecc_bch = 1;
+		info->chunk_size = 1024;
+		info->spare_size = 0;
+		info->ecc_size = 32;
+		ecc->mode = NAND_ECC_HW;
+		ecc->size = info->chunk_size;
+		ecc->layout = &ecc_layout_4KB_bch8bit;
+		ecc->strength = 16;
+		return 1;
+	}
 	return 0;
 }
 
@@ -1320,12 +1478,16 @@ static int alloc_nand_resource(struct platform_device *pdev)
 		chip->controller        = &info->controller;
 		chip->waitfunc		= pxa3xx_nand_waitfunc;
 		chip->select_chip	= pxa3xx_nand_select_chip;
-		chip->cmdfunc		= pxa3xx_nand_cmdfunc;
 		chip->read_word		= pxa3xx_nand_read_word;
 		chip->read_byte		= pxa3xx_nand_read_byte;
 		chip->read_buf		= pxa3xx_nand_read_buf;
 		chip->write_buf		= pxa3xx_nand_write_buf;
 		chip->options		|= NAND_NO_SUBPAGE_WRITE;
+
+		if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370)
+			chip->cmdfunc = armada370_nand_cmdfunc;
+		else
+			chip->cmdfunc = pxa3xx_nand_cmdfunc;
 	}
 
 	spin_lock_init(&chip->controller->lock);
-- 
1.8.1.5

[PATCH v4 26/31] mtd: nand: pxa3xx: Introduce multiple page I/O support

[Ezequiel Garcia]

Hello,

I have a concern about the ECC mode and strength determination.

On Thu, Nov 07, 2013 at 12:17:30PM -0300, Ezequiel Garcia wrote:
[..]
> @@ -1152,7 +1289,28 @@ static int armada370_ecc_init(struct pxa3xx_nand_info *info,
>  			      struct nand_ecc_ctrl *ecc,
>  			      int strength, int page_size)
>  {
> -	/* Unimplemented yet */
> +	if (strength == 4 && page_size == 4096) {
> +		info->ecc_bch = 1;
> +		info->chunk_size = 2048;
> +		info->spare_size = 32;
> +		info->ecc_size = 32;
> +		ecc->mode = NAND_ECC_HW;
> +		ecc->size = info->chunk_size;
> +		ecc->layout = &ecc_layout_4KB_bch4bit;
> +		ecc->strength = 16;
> +		return 1;
> +
> +	} else if (strength == 8 && page_size == 4096) {
> +		info->ecc_bch = 1;
> +		info->chunk_size = 1024;
> +		info->spare_size = 0;
> +		info->ecc_size = 32;
> +		ecc->mode = NAND_ECC_HW;
> +		ecc->size = info->chunk_size;
> +		ecc->layout = &ecc_layout_4KB_bch8bit;
> +		ecc->strength = 16;
> +		return 1;
> +	}
>  	return 0;
>  }
>  

The above shows I tried to be very careful (aka paranoid) in the ECC
mode determination. Please note that what I call "ECC mode", is
determined by the chunk->size value only.

As the included documentation explains this controller supports two
different BCH ECC strength: 16-over-1024, or 16-over-2048. Setting the chunk
size to either 1024 or 2048 is what determines which of the above will
actually take effect.

In past mails, we've refered to these two as BCH4 or BCH8, but this is not
really accurate (as Brian has pointed out) so I droped that terms in
favor of the real thing: 16 correctable bits over 1024 data bytes, or
16 correctable bits over 2048 data bytes.

In turn, such BCH mode setting affects heavily the page layout, because
after each transfered chunk (which is either 1024+spare or 2048+spare)
the controller reads and writes a 30B ECC region.

In other words, the kernel cannot arbitrarily change this setting, or
the image won't be readable/writeable any longer.

For this reason, I'm starting to think the above method of picking
the "ECC mode" based solely on the page size or the strength is slightly
fragile (future developers might come and "improve" the driver breaking
images).

Besides: what if a user wants the kernel to use a "higher" than
required strength?

In conclusion: I'm starting to think a better (and long-term safer)
approach is to set the ECC mode in the DT. I know this sucks, but from
my point of view the flash device contains an image that "must" be
read/write with a given ECC mode, and this ECC mode is by no means
discoverable.

Now, let's suppose we want to set this in the DT: what property
would we use? "marvell,nand-ecc-opt = 16-2048"? (a bit odd, no?).

What do you think?
-- 
Ezequiel Garc?a, Free Electrons
Embedded Linux, Kernel and Android Engineering
http://free-electrons.com

[PATCH v4 26/31] mtd: nand: pxa3xx: Introduce multiple page I/O support

[Brian Norris]

Hi,

I haven't taken a look at all your changes yet, but I'll get this
comment off my chest while it's still fresh :)

On Thu, Nov 07, 2013 at 08:45:00PM -0300, Ezequiel Garcia wrote:
> Hello,
> 
> I have a concern about the ECC mode and strength determination.
> 
> On Thu, Nov 07, 2013 at 12:17:30PM -0300, Ezequiel Garcia wrote:
> [..]
> > @@ -1152,7 +1289,28 @@ static int armada370_ecc_init(struct pxa3xx_nand_info *info,
> >  			      struct nand_ecc_ctrl *ecc,
> >  			      int strength, int page_size)
> >  {
> > -	/* Unimplemented yet */
> > +	if (strength == 4 && page_size == 4096) {
> > +		info->ecc_bch = 1;
> > +		info->chunk_size = 2048;
> > +		info->spare_size = 32;
> > +		info->ecc_size = 32;
> > +		ecc->mode = NAND_ECC_HW;
> > +		ecc->size = info->chunk_size;
> > +		ecc->layout = &ecc_layout_4KB_bch4bit;
> > +		ecc->strength = 16;
> > +		return 1;
> > +
> > +	} else if (strength == 8 && page_size == 4096) {
> > +		info->ecc_bch = 1;
> > +		info->chunk_size = 1024;
> > +		info->spare_size = 0;
> > +		info->ecc_size = 32;
> > +		ecc->mode = NAND_ECC_HW;
> > +		ecc->size = info->chunk_size;
> > +		ecc->layout = &ecc_layout_4KB_bch8bit;
> > +		ecc->strength = 16;
> > +		return 1;
> > +	}
> >  	return 0;
> >  }
> >  
> 
> The above shows I tried to be very careful (aka paranoid) in the ECC
> mode determination. Please note that what I call "ECC mode", is
> determined by the chunk->size value only.
> 
> As the included documentation explains this controller supports two
> different BCH ECC strength: 16-over-1024, or 16-over-2048. Setting the chunk
> size to either 1024 or 2048 is what determines which of the above will
> actually take effect.
> 
> In past mails, we've refered to these two as BCH4 or BCH8, but this is not
> really accurate (as Brian has pointed out) so I droped that terms in
> favor of the real thing: 16 correctable bits over 1024 data bytes, or
> 16 correctable bits over 2048 data bytes.
> 
> In turn, such BCH mode setting affects heavily the page layout, because
> after each transfered chunk (which is either 1024+spare or 2048+spare)
> the controller reads and writes a 30B ECC region.
> 
> In other words, the kernel cannot arbitrarily change this setting, or
> the image won't be readable/writeable any longer.
> 
> For this reason, I'm starting to think the above method of picking
> the "ECC mode" based solely on the page size or the strength is slightly
> fragile (future developers might come and "improve" the driver breaking
> images).
> 
> Besides: what if a user wants the kernel to use a "higher" than
> required strength?
> 
> In conclusion: I'm starting to think a better (and long-term safer)
> approach is to set the ECC mode in the DT. I know this sucks, but from
> my point of view the flash device contains an image that "must" be
> read/write with a given ECC mode, and this ECC mode is by no means
> discoverable.

I think that's the way to go, in general. We can get by with
"implementation defined behavior" (i.e., make the driver do what makes
sense) for now, but to avoid breakage in the future, the bootloader
needs to specify what ECC configuration is required -- via DT. But your
current patch is still probably fine without it, since you're supporting
new hardware.

> Now, let's suppose we want to set this in the DT: what property
> would we use? "marvell,nand-ecc-opt = 16-2048"? (a bit odd, no?).
> 
> What do you think?

If ECC is purely determined by the chunk size, then why not just:

  marvell,nand-chunk-size = 2048;
  (with a value of 2048, 1024, or 512?)

Brian

[PATCH v4 26/31] mtd: nand: pxa3xx: Introduce multiple page I/O support

[Ezequiel Garcia]

On Thu, Nov 07, 2013 at 04:46:00PM -0800, Brian Norris wrote:
> On Thu, Nov 07, 2013 at 08:45:00PM -0300, Ezequiel Garcia wrote:
> > Hello,
> > 
> > I have a concern about the ECC mode and strength determination.
> > 
> > On Thu, Nov 07, 2013 at 12:17:30PM -0300, Ezequiel Garcia wrote:
> > [..]
> > > @@ -1152,7 +1289,28 @@ static int armada370_ecc_init(struct pxa3xx_nand_info *info,
> > >  			      struct nand_ecc_ctrl *ecc,
> > >  			      int strength, int page_size)
> > >  {
> > > -	/* Unimplemented yet */
> > > +	if (strength == 4 && page_size == 4096) {
> > > +		info->ecc_bch = 1;
> > > +		info->chunk_size = 2048;
> > > +		info->spare_size = 32;
> > > +		info->ecc_size = 32;
> > > +		ecc->mode = NAND_ECC_HW;
> > > +		ecc->size = info->chunk_size;
> > > +		ecc->layout = &ecc_layout_4KB_bch4bit;
> > > +		ecc->strength = 16;
> > > +		return 1;
> > > +
> > > +	} else if (strength == 8 && page_size == 4096) {
> > > +		info->ecc_bch = 1;
> > > +		info->chunk_size = 1024;
> > > +		info->spare_size = 0;
> > > +		info->ecc_size = 32;
> > > +		ecc->mode = NAND_ECC_HW;
> > > +		ecc->size = info->chunk_size;
> > > +		ecc->layout = &ecc_layout_4KB_bch8bit;
> > > +		ecc->strength = 16;
> > > +		return 1;
> > > +	}
> > >  	return 0;
> > >  }
> > >  
> > 
> > The above shows I tried to be very careful (aka paranoid) in the ECC
> > mode determination. Please note that what I call "ECC mode", is
> > determined by the chunk->size value only.
> > 
> > As the included documentation explains this controller supports two
> > different BCH ECC strength: 16-over-1024, or 16-over-2048. Setting the chunk
> > size to either 1024 or 2048 is what determines which of the above will
> > actually take effect.
> > 
> > In past mails, we've refered to these two as BCH4 or BCH8, but this is not
> > really accurate (as Brian has pointed out) so I droped that terms in
> > favor of the real thing: 16 correctable bits over 1024 data bytes, or
> > 16 correctable bits over 2048 data bytes.
> > 
> > In turn, such BCH mode setting affects heavily the page layout, because
> > after each transfered chunk (which is either 1024+spare or 2048+spare)
> > the controller reads and writes a 30B ECC region.
> > 
> > In other words, the kernel cannot arbitrarily change this setting, or
> > the image won't be readable/writeable any longer.
> > 
> > For this reason, I'm starting to think the above method of picking
> > the "ECC mode" based solely on the page size or the strength is slightly
> > fragile (future developers might come and "improve" the driver breaking
> > images).
> > 
> > Besides: what if a user wants the kernel to use a "higher" than
> > required strength?
> > 
> > In conclusion: I'm starting to think a better (and long-term safer)
> > approach is to set the ECC mode in the DT. I know this sucks, but from
> > my point of view the flash device contains an image that "must" be
> > read/write with a given ECC mode, and this ECC mode is by no means
> > discoverable.
> 
> I think that's the way to go, in general. We can get by with
> "implementation defined behavior" (i.e., make the driver do what makes
> sense) for now, but to avoid breakage in the future, the bootloader
> needs to specify what ECC configuration is required -- via DT. But your
> current patch is still probably fine without it, since you're supporting
> new hardware.
> 

That sounds good. The ECC mode is currently "selected" in the driver
to be the one that "makes sense". In follow up patches we'll add a
proper DT binding, so this ECC mode can be set by the user.

The latter is an improvement over the former (adding more flexibility),
so there won't be any regressions.

Just to confirm: I consider this patchset to be OK as it is, and I expect
it to either get merged or receive some request for changes.

Oh, and by the way: we __really__ need someone to test for regressions on PXA.
-- 
Ezequiel Garc?a, Free Electrons
Embedded Linux, Kernel and Android Engineering
http://free-electrons.com

[PATCH v4 26/31] mtd: nand: pxa3xx: Introduce multiple page I/O support

[Ezequiel Garcia]

On Thu, Nov 07, 2013 at 04:46:00PM -0800, Brian Norris wrote:
> 
> I haven't taken a look at all your changes yet, but I'll get this

Any comments on the v4?

I don't think there are any open issues to reply, but maybe my memory
is failing, so feel free to refresh it :-)

I'll re-submit the series as soon as v3.13-rc1 is out.
-- 
Ezequiel Garc?a, Free Electrons
Embedded Linux, Kernel and Android Engineering
http://free-electrons.com

[PATCH v4 27/31] mtd: nand: pxa3xx: Add multiple chunk write support

[Ezequiel Garcia]

This commit adds write support for large pages (4 KiB, 8 KiB).
Such support is implemented by issuing a multiple command sequence,
transfering a set of 2 KiB chunks per transaction.

The splitted command sequence requires to send the SEQIN command
independently of the PAGEPROG command and therefore it's set as
an execution command.

Since PAGEPROG enables ECC, each 2 KiB chunk of data is written
together with ECC code at a controller-fixed location within
the flash page.

Currently, only devices with a 4 KiB page size has been tested.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 81 +++++++++++++++++++++++++++++++++++++-----
 1 file changed, 73 insertions(+), 8 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 51d90cc..4c9acf7 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -760,6 +760,20 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
 
 		info->buf_start = column;
 		set_command_address(info, mtd->writesize, 0, page_addr);
+
+		/*
+		 * Multiple page programming needs to execute the initial
+		 * SEQIN command that sets the page address.
+		 */
+		if (mtd->writesize > PAGE_CHUNK_SIZE) {
+			info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
+				| NDCB0_EXT_CMD_TYPE(ext_cmd_type)
+				| addr_cycle
+				| command;
+			/* No data transfer in this case */
+			info->data_size = 0;
+			exec_cmd = 1;
+		}
 		break;
 
 	case NAND_CMD_PAGEPROG:
@@ -769,13 +783,40 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
 			break;
 		}
 
-		info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
-				| NDCB0_AUTO_RS
-				| NDCB0_ST_ROW_EN
-				| NDCB0_DBC
-				| (NAND_CMD_PAGEPROG << 8)
-				| NAND_CMD_SEQIN
-				| addr_cycle;
+		/* Second command setting for large pages */
+		if (mtd->writesize > PAGE_CHUNK_SIZE) {
+			/*
+			 * Multiple page write uses the 'extended command'
+			 * field. This can be used to issue a command dispatch
+			 * or a naked-write depending on the current stage.
+			 */
+			info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
+					| NDCB0_LEN_OVRD
+					| NDCB0_EXT_CMD_TYPE(ext_cmd_type);
+			info->ndcb3 = info->chunk_size +
+				      info->oob_size;
+
+			/*
+			 * This is the command dispatch that completes a chunked
+			 * page program operation.
+			 */
+			if (info->data_size == 0) {
+				info->ndcb0 = NDCB0_CMD_TYPE(0x1)
+					| NDCB0_EXT_CMD_TYPE(ext_cmd_type)
+					| command;
+				info->ndcb1 = 0;
+				info->ndcb2 = 0;
+				info->ndcb3 = 0;
+			}
+		} else {
+			info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
+					| NDCB0_AUTO_RS
+					| NDCB0_ST_ROW_EN
+					| NDCB0_DBC
+					| (NAND_CMD_PAGEPROG << 8)
+					| NAND_CMD_SEQIN
+					| addr_cycle;
+		}
 		break;
 
 	case NAND_CMD_PARAM:
@@ -919,8 +960,15 @@ static void armada370_nand_cmdfunc(struct mtd_info *mtd,
 	case NAND_CMD_READOOB:
 		ext_cmd_type = EXT_CMD_TYPE_MONO;
 		break;
+	case NAND_CMD_SEQIN:
+		ext_cmd_type = EXT_CMD_TYPE_DISPATCH;
+		break;
+	case NAND_CMD_PAGEPROG:
+		ext_cmd_type = EXT_CMD_TYPE_NAKED_RW;
+		break;
 	default:
 		ext_cmd_type = 0;
+		break;
 	}
 
 	prepare_start_command(info, command);
@@ -958,7 +1006,16 @@ static void armada370_nand_cmdfunc(struct mtd_info *mtd,
 		}
 
 		/* Check if the sequence is complete */
-		if (info->data_size == 0)
+		if (info->data_size == 0 && command != NAND_CMD_PAGEPROG)
+			break;
+
+		/*
+		 * After a splitted program command sequence has issued
+		 * the command dispatch, the command sequence is complete.
+		 */
+		if (info->data_size == 0 &&
+		    command == NAND_CMD_PAGEPROG &&
+		    ext_cmd_type == EXT_CMD_TYPE_DISPATCH)
 			break;
 
 		if (command == NAND_CMD_READ0 || command == NAND_CMD_READOOB) {
@@ -967,6 +1024,14 @@ static void armada370_nand_cmdfunc(struct mtd_info *mtd,
 				ext_cmd_type = EXT_CMD_TYPE_LAST_RW;
 			else
 				ext_cmd_type = EXT_CMD_TYPE_NAKED_RW;
+
+		/*
+		 * If a splitted program command has no more data to transfer,
+		 * the command dispatch must be issued to complete.
+		 */
+		} else if (command == NAND_CMD_PAGEPROG &&
+			   info->data_size == 0) {
+				ext_cmd_type = EXT_CMD_TYPE_DISPATCH;
 		}
 	} while (1);
 
-- 
1.8.1.5

[PATCH v4 28/31] mtd: nand: pxa3xx: Add ECC BCH correctable errors detection

[Ezequiel Garcia]

This commit extends the ECC correctable error detection to include
ECC BCH errors. The number of BCH correctable errors can be any up to 16,
and the actual value is exposed in the NDSR register.

Therefore, we change some symbol names to refer to correctable or
uncorrectable (instead of single-bit or double-bit as it was in the
Hamming case) and while at it, cleanup the detection code slightly.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 57 ++++++++++++++++++++++++++----------------
 1 file changed, 35 insertions(+), 22 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 4c9acf7..279e9fc 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -85,6 +85,9 @@
 #define NDCR_INT_MASK           (0xFFF)
 
 #define NDSR_MASK		(0xfff)
+#define NDSR_ERR_CNT_OFF	(16)
+#define NDSR_ERR_CNT_MASK       (0x1f)
+#define NDSR_ERR_CNT(sr)	((sr >> NDSR_ERR_CNT_OFF) & NDSR_ERR_CNT_MASK)
 #define NDSR_RDY                (0x1 << 12)
 #define NDSR_FLASH_RDY          (0x1 << 11)
 #define NDSR_CS0_PAGED		(0x1 << 10)
@@ -93,8 +96,8 @@
 #define NDSR_CS1_CMDD		(0x1 << 7)
 #define NDSR_CS0_BBD		(0x1 << 6)
 #define NDSR_CS1_BBD		(0x1 << 5)
-#define NDSR_DBERR		(0x1 << 4)
-#define NDSR_SBERR		(0x1 << 3)
+#define NDSR_UNCORERR		(0x1 << 4)
+#define NDSR_CORERR		(0x1 << 3)
 #define NDSR_WRDREQ		(0x1 << 2)
 #define NDSR_RDDREQ		(0x1 << 1)
 #define NDSR_WRCMDREQ		(0x1)
@@ -135,9 +138,9 @@ enum {
 	ERR_NONE	= 0,
 	ERR_DMABUSERR	= -1,
 	ERR_SENDCMD	= -2,
-	ERR_DBERR	= -3,
+	ERR_UNCORERR	= -3,
 	ERR_BBERR	= -4,
-	ERR_SBERR	= -5,
+	ERR_CORERR	= -5,
 };
 
 enum {
@@ -221,6 +224,8 @@ struct pxa3xx_nand_info {
 	unsigned int		oob_size;
 	unsigned int		spare_size;
 	unsigned int		ecc_size;
+	unsigned int		ecc_err_cnt;
+	unsigned int		max_bitflips;
 	int 			retcode;
 
 	/* cached register value */
@@ -571,10 +576,25 @@ static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
 
 	status = nand_readl(info, NDSR);
 
-	if (status & NDSR_DBERR)
-		info->retcode = ERR_DBERR;
-	if (status & NDSR_SBERR)
-		info->retcode = ERR_SBERR;
+	if (status & NDSR_UNCORERR)
+		info->retcode = ERR_UNCORERR;
+	if (status & NDSR_CORERR) {
+		info->retcode = ERR_CORERR;
+		if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 &&
+		    info->ecc_bch)
+			info->ecc_err_cnt = NDSR_ERR_CNT(status);
+		else
+			info->ecc_err_cnt = 1;
+
+		/*
+		 * Each chunk composing a page is corrected independently,
+		 * and we need to store maximum number of corrected bitflips
+		 * to return it to the MTD layer in ecc.read_page().
+		 */
+		info->max_bitflips = max_t(unsigned int,
+					   info->max_bitflips,
+					   info->ecc_err_cnt);
+	}
 	if (status & (NDSR_RDDREQ | NDSR_WRDREQ)) {
 		/* whether use dma to transfer data */
 		if (info->use_dma) {
@@ -672,6 +692,7 @@ static void prepare_start_command(struct pxa3xx_nand_info *info, int command)
 	info->use_ecc		= 0;
 	info->use_spare		= 1;
 	info->retcode		= ERR_NONE;
+	info->ecc_err_cnt	= 0;
 	info->ndcb3		= 0;
 
 	switch (command) {
@@ -1053,26 +1074,18 @@ static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
 {
 	struct pxa3xx_nand_host *host = mtd->priv;
 	struct pxa3xx_nand_info *info = host->info_data;
-	int max_bitflips = 0;
 
 	chip->read_buf(mtd, buf, mtd->writesize);
 	chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
 
-	if (info->retcode == ERR_SBERR) {
-		switch (info->use_ecc) {
-		case 1:
-			max_bitflips = 1;
-			mtd->ecc_stats.corrected++;
-			break;
-		case 0:
-		default:
-			break;
-		}
-	} else if (info->retcode == ERR_DBERR) {
+	if (info->retcode == ERR_CORERR && info->use_ecc) {
+		mtd->ecc_stats.corrected += info->ecc_err_cnt;
+
+	} else if (info->retcode == ERR_UNCORERR) {
 		/*
 		 * for blank page (all 0xff), HW will calculate its ECC as
 		 * 0, which is different from the ECC information within
-		 * OOB, ignore such double bit errors
+		 * OOB, ignore such ucorrectable errors
 		 */
 		if (is_buf_blank(buf, mtd->writesize))
 			info->retcode = ERR_NONE;
@@ -1080,7 +1093,7 @@ static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
 			mtd->ecc_stats.failed++;
 	}
 
-	return max_bitflips;
+	return info->max_bitflips;
 }
 
 static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd)
-- 
1.8.1.5

[PATCH v4 29/31] ARM: mvebu: Add support for NAND controller in Armada 370/XP

[Ezequiel Garcia]

The Armada 370 and Armada XP SoC have a NAND controller (aka NFCv2).
This commit adds support for it in Armada 370 and Armada XP SoC
common devicetree.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 arch/arm/boot/dts/armada-370-xp.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi
index 01e69fc..b4e6898 100644
--- a/arch/arm/boot/dts/armada-370-xp.dtsi
+++ b/arch/arm/boot/dts/armada-370-xp.dtsi
@@ -258,6 +258,15 @@
 				status = "disabled";
 			};
 
+			nand at d0000 {
+				compatible = "marvell,armada370-nand";
+				reg = <0xd0000 0x54>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				interrupts = <113>;
+				clocks = <&coredivclk 0>;
+				status = "disabled";
+			};
 		};
 	};
 
-- 
1.8.1.5

[PATCH v4 29/31] ARM: mvebu: Add support for NAND controller in Armada 370/XP

[Jason Cooper]

On Thu, Nov 07, 2013 at 12:17:33PM -0300, Ezequiel Garcia wrote:
> The Armada 370 and Armada XP SoC have a NAND controller (aka NFCv2).
> This commit adds support for it in Armada 370 and Armada XP SoC
> common devicetree.
> 
> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
> ---
>  arch/arm/boot/dts/armada-370-xp.dtsi | 9 +++++++++
>  1 file changed, 9 insertions(+)

Patches 29 (this one), 30 and 31 applied to mvebu/dt

I'll be working on the core-divider clock issue over the next couple of
days.

thx,

Jason.

[PATCH v4 30/31] ARM: mvebu: Enable NAND controller in Armada XP GP board

[Ezequiel Garcia]

The Armada XP GP board has a NAND flash, so enable it in the devicetree.

In order to skip the driver's custom device detection and use only ONFI
detection, the "marvell,keep-config" parameter is used.
This is needed because we haven't support for setting the timings
parameters yet and must rely in bootloader's.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 arch/arm/boot/dts/armada-xp-gp.dts | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts
index 2298e4a..274e2ad 100644
--- a/arch/arm/boot/dts/armada-xp-gp.dts
+++ b/arch/arm/boot/dts/armada-xp-gp.dts
@@ -175,6 +175,14 @@
 					spi-max-frequency = <108000000>;
 				};
 			};
+
+			nand at d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+			};
 		};
 	};
 };
-- 
1.8.1.5

[PATCH v4 31/31] ARM: mvebu: Enable NAND controller in Armada 370 Mirabox

[Ezequiel Garcia]

The Armada 370 Mirabox has a NAND flash, so enable it in the devicetree
and add the partitions as prepared in the factory images.

In order to skip the driver's custom device detection and use only
ONFI detection, the "marvell,keep-config" parameter is used.
This is needed because we have no support for setting the timings parameters yet.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
---
 arch/arm/boot/dts/armada-370-mirabox.dts | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/arch/arm/boot/dts/armada-370-mirabox.dts b/arch/arm/boot/dts/armada-370-mirabox.dts
index 2471d9d..1e73017 100644
--- a/arch/arm/boot/dts/armada-370-mirabox.dts
+++ b/arch/arm/boot/dts/armada-370-mirabox.dts
@@ -139,6 +139,27 @@
 					reg = <0x25>;
 				};
 			};
+
+			nand at d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+
+				partition at 0 {
+					label = "U-Boot";
+					reg = <0 0x400000>;
+				};
+				partition at 400000 {
+					label = "Linux";
+					reg = <0x400000 0x400000>;
+				};
+				partition at 800000 {
+					label = "Filesystem";
+					reg = <0x800000 0x3f800000>;
+				};
+			};
 		};
 	};
 };
-- 
1.8.1.5

[PATCH v4 00/31] Armada 370/XP NAND support

[Ezequiel Garcia]

Brian,

If at all possible I would like the feedback not to stall,
so the discussion (which is pretty complex) is still fresh in
everybody's mind (specially mine!).

Thanks!

On Thu, Nov 07, 2013 at 12:17:04PM -0300, Ezequiel Garcia wrote:
> Another version of the Armada 370/XP SoCs v3 patchset, addressing
> all the feedback provided by Brian Norris.
> 
> Please see Documentation/mtd/nand/pxa3xx-nand.txt for specific details
> about the controller and the driver.
> 
> Just as the last version, the bad block factory initial detection issue
> is not addressed by this patchset, but support for it will be added in
> a near future once we decide the proper roadmap. See here the discussion
> about it:
> 
>   http://permalink.gmane.org/gmane.linux.drivers.mtd/49401
> 
> As usual patches 1-4, adding the clock infrastructure have already been merged
> and will be dropped once this series can be based on v3.13-rc1.
> I'm including them just for completeness.
> 
> Based in l2-mtd's master branch. Also, I've pushed a branch to our github
> in case anyone wants to test it:
> 
>   https://github.com/MISL-EBU-System-SW/mainline-public/tree/l2-mtd/upstream-nand-v4
> 
> As per Jason Cooper's suggestion I'm Ccing devicetree mailing list, to get a review
> on the small binding changes this patchset contains. If the devicetree people wants
> us to just Cc you on the relevant patches, just let us know.
> 
> Of course, there's some room for improvements in this driver, and I'll probably
> continue working on it. However, for now I'd like to focus in adding the strict
> minimum amount of changes required to support the new SoC family and pospone any
> improvements.
> 
> Thanks!
> 
> * Changes from v3 (feedback from Brian Norris)
> 
>   * Add binding documentation for the nand-flash-bbt DT property.
> 
>   * Expand in the documentation and in a comment the reason for
>     setting the NAND_BBT_NO_OOB_BBM option.
> 
>   * Reworked the 'is_ready' completion handler. We still have
>     two completions, but we've dropped the atomic_t type as
>     now the variable is no longer accesed from interruption context.
> 
>   * Fixed the ecc.read_page() which lacked the max_bitflip return.
> 
>   * Reworked the ECC strength and size setting. This is important
>     to allow the MTD layer to properly report on bitflip threshold
>     situation.
> 
>   * Dropped an unused fifo_size state variable
> 
>   * Use '0' instead of the wrong '-1' when the extended command type
>     doesn't matter or extended semantics are not supposed to be used.
> 
> * Changes from v2 (some minor fixes as per Huang's good feedback)
> 
>   * Add some more details to the commit log in patch
>     "mtd: nand: pxa3xx: Early variant detection"
> 
>   * Add an empty line between variable declaration and function body
>     in patch "mtd: nand: pxa3xx: Use chip->cmdfunc instead of the internal".
> 
>   * Fix a build break caused by incomplete variable replacement:
>     "mtd: nand: pxa3xx: Replace host->page_size by mtd->writesize"
> 
> * Changes from v1
> 
> Aside from several changes based in Brian's feedback, the main changes
> from v1 are:
> 
>   * The controller's clock source is now fully modeled, see patche 1 to 4.
>     Of course, none of those patches should be taken through the mtd
>     subsystem, but I'm adding them here for completeness.
> 
>   * The chip's cmdfunc() is now independently implemented in each SoC variant.
>     The rationale behind this decision is that 'chunked' I/O is the only tested
>     mode on the Armada370 variant, while the old 'vanilla' I/O is the only
>     tested mode on the PXA variant.
> 
>     So it's safer to have an implementation for each variant.
> 
>   * Added support for BCH-8, in other words: 8-bits of correction in a 512-byte
>     region. This is obtained by using a data chunk size of 1024B, thus doubling
>     the ECC BCH strength, as per this ECC engine mechanism.
> 
>   * The ECC layout in use, which must be set according to the page size and
>     desired ECC strength is now strictly chosen to match only the tested
>     combinations.
> 
> Ezequiel Garcia (31):
>   clk: mvebu: Add Core Divider clock
>   ARM: mvebu: Add Core Divider clock device-tree binding
>   ARM: mvebu: Add a 2 GHz fixed-clock Armada 370/XP
>   ARM: mvebu: Add the core-divider clock to Armada 370/XP
>   mtd: nand: pxa3xx: devicetree binding update
>   mtd: nand: pxa3xx: Add documentation about the controller
>   mtd: nand: pxa3xx: Make config menu show supported platforms
>   mtd: nand: pxa3xx: Prevent sub-page writes
>   mtd: nand: pxa3xx: read_page() returns max_bitflips
>   mtd: nand: pxa3xx: Early variant detection
>   mtd: nand: pxa3xx: Use chip->cmdfunc instead of the internal
>   mtd: nand: pxa3xx: Split FIFO size from to-be-read FIFO count
>   mtd: nand: pxa3xx: Replace host->page_size by mtd->writesize
>   mtd: nand: pxa3xx: Add a nice comment to pxa3xx_set_datasize()
>   mtd: nand: pxa3xx: Use a completion to signal device ready
>   mtd: nand: pxa3xx: Use waitfunc() to wait for the device to be ready
>   mtd: nand: pxa3xx: Add bad block handling
>   mtd: nand: pxa3xx: Add driver-specific ECC BCH support
>   mtd: nand: pxa3xx: Clear cmd buffer #3 (NDCB3) on command start
>   mtd: nand: pxa3xx: Add helper function to set page address
>   mtd: nand: pxa3xx: Remove READ0 switch/case falltrough
>   mtd: nand: pxa3xx: Split prepare_command_pool() in two stages
>   mtd: nand: pxa3xx: Move the data buffer clean to
>     prepare_start_command()
>   mtd: nand: pxa3xx: Fix SEQIN column address set
>   mtd: nand: pxa3xx: Add a read/write buffers markers
>   mtd: nand: pxa3xx: Introduce multiple page I/O support
>   mtd: nand: pxa3xx: Add multiple chunk write support
>   mtd: nand: pxa3xx: Add ECC BCH correctable errors detection
>   ARM: mvebu: Add support for NAND controller in Armada 370/XP
>   ARM: mvebu: Enable NAND controller in Armada XP GP board
>   ARM: mvebu: Enable NAND controller in Armada 370 Mirabox
> 
>  .../bindings/clock/mvebu-corediv-clock.txt         |  19 +
>  .../devicetree/bindings/mtd/pxa3xx-nand.txt        |   6 +-
>  Documentation/mtd/nand/pxa3xx-nand.txt             | 113 ++++
>  arch/arm/boot/dts/armada-370-mirabox.dts           |  21 +
>  arch/arm/boot/dts/armada-370-xp.dtsi               |  26 +
>  arch/arm/boot/dts/armada-xp-gp.dts                 |   8 +
>  drivers/clk/mvebu/Kconfig                          |   5 +
>  drivers/clk/mvebu/Makefile                         |   1 +
>  drivers/clk/mvebu/clk-corediv.c                    | 223 +++++++
>  drivers/mtd/nand/Kconfig                           |   4 +-
>  drivers/mtd/nand/pxa3xx_nand.c                     | 678 ++++++++++++++++-----
>  include/linux/platform_data/mtd-nand-pxa3xx.h      |   3 +
>  12 files changed, 965 insertions(+), 142 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
>  create mode 100644 Documentation/mtd/nand/pxa3xx-nand.txt
>  create mode 100644 drivers/clk/mvebu/clk-corediv.c
> 
> -- 
> 1.8.1.5
> 

-- 
Ezequiel Garc?a, Free Electrons
Embedded Linux, Kernel and Android Engineering
http://free-electrons.com

[PATCH v4 00/31] Armada 370/XP NAND support

[Ezequiel Garcia]

Hello,

On Thu, Nov 07, 2013 at 12:17:04PM -0300, Ezequiel Garcia wrote:
> Another version of the Armada 370/XP SoCs v3 patchset, addressing
> all the feedback provided by Brian Norris.
> 
> Please see Documentation/mtd/nand/pxa3xx-nand.txt for specific details
> about the controller and the driver.
> 
> Just as the last version, the bad block factory initial detection issue
> is not addressed by this patchset, but support for it will be added in
> a near future once we decide the proper roadmap. See here the discussion
> about it:
> 
>   http://permalink.gmane.org/gmane.linux.drivers.mtd/49401
> 
> As usual patches 1-4, adding the clock infrastructure have already been merged
> and will be dropped once this series can be based on v3.13-rc1.
> I'm including them just for completeness.
> 
> Based in l2-mtd's master branch. Also, I've pushed a branch to our github
> in case anyone wants to test it:
> 
>   https://github.com/MISL-EBU-System-SW/mainline-public/tree/l2-mtd/upstream-nand-v4
> 
> As per Jason Cooper's suggestion I'm Ccing devicetree mailing list, to get a review
> on the small binding changes this patchset contains. If the devicetree people wants
> us to just Cc you on the relevant patches, just let us know.
> 
> Of course, there's some room for improvements in this driver, and I'll probably
> continue working on it. However, for now I'd like to focus in adding the strict
> minimum amount of changes required to support the new SoC family and pospone any
> improvements.
> 

After some powering issues, I could boot my PXA3xx board (CM-X300 from
Compulab) and I've tested this patchset on it. In other words: no
regression on PXA! both DMA and non-DMA works.

Daniel: feel free to confirm my check, but it's no longer required,
in case you are too busy at the moment. I'll be able to test your
dmaengine work on this board, so feel free to Cc me on it.

Big thanks to Compulab for sending me the board, and specially
to Igor and Nikita!
-- 
Ezequiel Garc?a, Free Electrons
Embedded Linux, Kernel and Android Engineering
http://free-electrons.com