* [PATCH V6 2/3] ahci: imx: Pull out the clock enable/disable calls
2013-11-25 8:47 [PATCH V3 1/3] ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN Marek Vasut
@ 2013-11-25 8:47 ` Marek Vasut
2013-12-03 12:42 ` Tejun Heo
2013-11-25 8:47 ` [PATCH V6 3/3] ahci: imx: Add i.MX53 support Marek Vasut
` (2 subsequent siblings)
3 siblings, 1 reply; 11+ messages in thread
From: Marek Vasut @ 2013-11-25 8:47 UTC (permalink / raw)
To: linux-arm-kernel
The same code for enabling and disabling SATA clock was found in multiple
places in the driver. Implement functions that enable/disable the SATA clock
and use them in such places instead of duplicating the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linux-IDE <linux-ide@vger.kernel.org>
---
drivers/ata/ahci_imx.c | 143 ++++++++++++++++++++++++++-----------------------
1 file changed, 75 insertions(+), 68 deletions(-)
V2: Move the OR sign from the begining of the line to the end of the line in
the regmap_update_bits() call.
V3: Move the PHY configuration programming out of the clock_enable function
and into the probe() function.
V4: Rebase on top of new 1/6 patch.
Remove clk_prepare_enable() being called twice in imx_sata_clock_enable()
since it was a rebase artifact.
V5: Pull out the usleep_range() into imx_sata_clock_enable() as well as a small
delay is needed after turning on the clock. Also rebase this on top of the
change in comment in 1/6 .
V6: Rebase this on top of the change in comment in 1/3 .
diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c
index 3e23e99..6214411 100644
--- a/drivers/ata/ahci_imx.c
+++ b/drivers/ata/ahci_imx.c
@@ -47,6 +47,36 @@ static int ahci_imx_hotplug;
module_param_named(hotplug, ahci_imx_hotplug, int, 0644);
MODULE_PARM_DESC(hotplug, "AHCI IMX hot-plug support (0=Don't support, 1=support)");
+static int imx_sata_clock_enable(struct device *dev)
+{
+ struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
+ int ret;
+
+ ret = clk_prepare_enable(imxpriv->sata_ref_clk);
+ if (ret < 0) {
+ dev_err(dev, "prepare-enable sata_ref clock err:%d\n", ret);
+ return ret;
+ }
+
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN,
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN);
+
+ usleep_range(1000, 2000);
+
+ return 0;
+}
+
+static void imx_sata_clock_disable(struct device *dev)
+{
+ struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
+
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN,
+ !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
+ clk_disable_unprepare(imxpriv->sata_ref_clk);
+}
+
static void ahci_imx_error_handler(struct ata_port *ap)
{
u32 reg_val;
@@ -72,10 +102,7 @@ static void ahci_imx_error_handler(struct ata_port *ap)
*/
reg_val = readl(mmio + PORT_PHY_CTL);
writel(reg_val | PORT_PHY_CTL_PDDQ_LOC, mmio + PORT_PHY_CTL);
- regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- clk_disable_unprepare(imxpriv->sata_ref_clk);
+ imx_sata_clock_disable(ap->dev);
imxpriv->no_device = true;
}
@@ -97,46 +124,9 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)
unsigned int reg_val;
struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
- imxpriv->gpr =
- syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
- if (IS_ERR(imxpriv->gpr)) {
- dev_err(dev, "failed to find fsl,imx6q-iomux-gpr regmap\n");
- return PTR_ERR(imxpriv->gpr);
- }
-
- ret = clk_prepare_enable(imxpriv->sata_ref_clk);
- if (ret < 0) {
- dev_err(dev, "prepare-enable sata_ref clock err:%d\n", ret);
+ ret = imx_sata_clock_enable(dev);
+ if (ret < 0)
return ret;
- }
-
- /*
- * set PHY Paremeters, two steps to configure the GPR13,
- * one write for rest of parameters, mask of first write
- * is 0x07ffffff, and the other one write for setting
- * the mpll_clk_en.
- */
- regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK
- | IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK
- | IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK
- | IMX6Q_GPR13_SATA_SPD_MODE_MASK
- | IMX6Q_GPR13_SATA_MPLL_SS_EN
- | IMX6Q_GPR13_SATA_TX_ATTEN_MASK
- | IMX6Q_GPR13_SATA_TX_BOOST_MASK
- | IMX6Q_GPR13_SATA_TX_LVL_MASK
- | IMX6Q_GPR13_SATA_MPLL_CLK_EN
- | IMX6Q_GPR13_SATA_TX_EDGE_RATE
- , IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB
- | IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M
- | IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F
- | IMX6Q_GPR13_SATA_SPD_MODE_3P0G
- | IMX6Q_GPR13_SATA_MPLL_SS_EN
- | IMX6Q_GPR13_SATA_TX_ATTEN_9_16
- | IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB
- | IMX6Q_GPR13_SATA_TX_LVL_1_025_V);
- regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- usleep_range(100, 200);
/*
* Configure the HWINIT bits of the HOST_CAP and HOST_PORTS_IMPL,
@@ -164,11 +154,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)
static void imx6q_sata_exit(struct device *dev)
{
- struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
-
- regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- clk_disable_unprepare(imxpriv->sata_ref_clk);
+ imx_sata_clock_disable(dev);
}
static int imx_ahci_suspend(struct device *dev)
@@ -179,12 +165,8 @@ static int imx_ahci_suspend(struct device *dev)
* If no_device is set, The CLKs had been gated off in the
* initialization so don't do it again here.
*/
- if (!imxpriv->no_device) {
- regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- clk_disable_unprepare(imxpriv->sata_ref_clk);
- }
+ if (!imxpriv->no_device)
+ imx_sata_clock_disable(dev);
return 0;
}
@@ -192,22 +174,12 @@ static int imx_ahci_suspend(struct device *dev)
static int imx_ahci_resume(struct device *dev)
{
struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
- int ret;
+ int ret = 0;
- if (!imxpriv->no_device) {
- ret = clk_prepare_enable(imxpriv->sata_ref_clk);
- if (ret < 0) {
- dev_err(dev, "pre-enable sata_ref clock err:%d\n", ret);
- return ret;
- }
-
- regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- usleep_range(1000, 2000);
- }
+ if (!imxpriv->no_device)
+ ret = imx_sata_clock_enable(dev);
- return 0;
+ return ret;
}
static struct ahci_platform_data imx6q_sata_pdata = {
@@ -290,6 +262,41 @@ static int imx_ahci_probe(struct platform_device *pdev)
ahci_dev->dma_mask = &ahci_dev->coherent_dma_mask;
ahci_dev->of_node = dev->of_node;
+ imxpriv->gpr =
+ syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
+
+ if (IS_ERR(imxpriv->gpr)) {
+ dev_err(dev, "failed to find fsl,imx6q-iomux-gpr regmap\n");
+ ret = PTR_ERR(imxpriv->gpr);
+ goto err_out;
+ }
+
+ /*
+ * Set PHY Paremeters, two steps to configure the GPR13,
+ * one write for rest of parameters, mask of first write
+ * is 0x07ffffff, and the other one write for setting
+ * the mpll_clk_en happens in imx_sata_clock_enable().
+ */
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK |
+ IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK |
+ IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK |
+ IMX6Q_GPR13_SATA_SPD_MODE_MASK |
+ IMX6Q_GPR13_SATA_MPLL_SS_EN |
+ IMX6Q_GPR13_SATA_TX_ATTEN_MASK |
+ IMX6Q_GPR13_SATA_TX_BOOST_MASK |
+ IMX6Q_GPR13_SATA_TX_LVL_MASK |
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN |
+ IMX6Q_GPR13_SATA_TX_EDGE_RATE,
+ IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB |
+ IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M |
+ IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F |
+ IMX6Q_GPR13_SATA_SPD_MODE_3P0G |
+ IMX6Q_GPR13_SATA_MPLL_SS_EN |
+ IMX6Q_GPR13_SATA_TX_ATTEN_9_16 |
+ IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB |
+ IMX6Q_GPR13_SATA_TX_LVL_1_025_V);
+
ret = platform_device_add_resources(ahci_pdev, res, 2);
if (ret)
goto err_out;
--
1.8.4.3
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH V6 3/3] ahci: imx: Add i.MX53 support
2013-11-25 8:47 [PATCH V3 1/3] ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN Marek Vasut
2013-11-25 8:47 ` [PATCH V6 2/3] ahci: imx: Pull out the clock enable/disable calls Marek Vasut
@ 2013-11-25 8:47 ` Marek Vasut
2013-12-10 11:47 ` Sascha Hauer
2013-11-29 22:28 ` [PATCH V3 1/3] ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN Tejun Heo
2013-12-03 12:41 ` Tejun Heo
3 siblings, 1 reply; 11+ messages in thread
From: Marek Vasut @ 2013-11-25 8:47 UTC (permalink / raw)
To: linux-arm-kernel
Add minor adjustments to support i.MX53 SATA port as well as i.MX6Q one.
The difference here is mostly the clock which need to be enabled and also
the lack of need of programming IOMUXC registers on i.MX53. All of which
is well handles in the clock enable/disable functions. Note that this patch
also cleans up the names of the common functions, so they don't read imx6q_*
but imx_* instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linux-IDE <linux-ide@vger.kernel.org>
---
drivers/ata/ahci_imx.c | 180 +++++++++++++++++++++++++++++++++----------------
1 file changed, 122 insertions(+), 58 deletions(-)
V2: Rebase this patch to be coherent with formating change in 1/5 .
V3: Rebase this patch to be coherent with change in 1/5 .
V4: Use sata_ref_clk for both MX53 and MX6 instead of separate sata_phy_clk
for MX53.
V5: Rebase on top of changes in 1/6 and 2/6 . Note that I am keeping the small
delay after enabling clock on MX53 as well.
V6: Rebase on top of changes in 1/3 and 2/3 . Also, this is important, add
softreset hook for the i.MX53 implemented by the ahci_imx_softreset()
function. For MX6, This function invokes the regular AHCI softreset
function, but for MX53 a function which retries the softreset is invoked.
The reset hook is needed, otherwise I observe some drives are not detected
at all.
diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c
index 6214411..8cb8965 100644
--- a/drivers/ata/ahci_imx.c
+++ b/drivers/ata/ahci_imx.c
@@ -34,10 +34,21 @@ enum {
HOST_TIMER1MS = 0xe0, /* Timer 1-ms */
};
+enum ahci_imx_type {
+ AHCI_IMX53,
+ AHCI_IMX6Q,
+};
+
struct imx_ahci_priv {
struct platform_device *ahci_pdev;
+ enum ahci_imx_type type;
+
+ /* i.MX53 clock */
+ struct clk *sata_gate_clk;
+ /* Common clock */
struct clk *sata_ref_clk;
struct clk *ahb_clk;
+
struct regmap *gpr;
bool no_device;
bool first_time;
@@ -52,29 +63,52 @@ static int imx_sata_clock_enable(struct device *dev)
struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
int ret;
+ if (imxpriv->type == AHCI_IMX53) {
+ ret = clk_prepare_enable(imxpriv->sata_gate_clk);
+ if (ret < 0) {
+ dev_err(dev, "prepare-enable sata_gate clock err:%d\n",
+ ret);
+ return ret;
+ }
+ }
+
ret = clk_prepare_enable(imxpriv->sata_ref_clk);
if (ret < 0) {
- dev_err(dev, "prepare-enable sata_ref clock err:%d\n", ret);
- return ret;
+ dev_err(dev, "prepare-enable sata_ref clock err:%d\n",
+ ret);
+ goto clk_err;
}
- regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN);
+ if (imxpriv->type == AHCI_IMX6Q) {
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN,
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN);
+ }
usleep_range(1000, 2000);
return 0;
+
+clk_err:
+ if (imxpriv->type == AHCI_IMX53)
+ clk_disable_unprepare(imxpriv->sata_gate_clk);
+ return ret;
}
static void imx_sata_clock_disable(struct device *dev)
{
struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
- regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
+ if (imxpriv->type == AHCI_IMX6Q) {
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN,
+ !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
+ }
+
clk_disable_unprepare(imxpriv->sata_ref_clk);
+
+ if (imxpriv->type == AHCI_IMX53)
+ clk_disable_unprepare(imxpriv->sata_gate_clk);
}
static void ahci_imx_error_handler(struct ata_port *ap)
@@ -106,9 +140,25 @@ static void ahci_imx_error_handler(struct ata_port *ap)
imxpriv->no_device = true;
}
+int ahci_imx_softreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
+{
+ struct ata_port *ap = link->ap;
+ struct imx_ahci_priv *imxpriv = dev_get_drvdata(ap->dev->parent);
+ int ret = -EIO;
+
+ if (imxpriv->type == AHCI_IMX53)
+ ret = ahci_pmp_retry_srst_ops.softreset(link, class, deadline);
+ else if (imxpriv->type == AHCI_IMX6Q)
+ ret = ahci_ops.softreset(link, class, deadline);
+
+ return ret;
+}
+
static struct ata_port_operations ahci_imx_ops = {
.inherits = &ahci_platform_ops,
.error_handler = ahci_imx_error_handler,
+ .softreset = ahci_imx_softreset,
};
static const struct ata_port_info ahci_imx_port_info = {
@@ -118,7 +168,7 @@ static const struct ata_port_info ahci_imx_port_info = {
.port_ops = &ahci_imx_ops,
};
-static int imx6q_sata_init(struct device *dev, void __iomem *mmio)
+static int imx_sata_init(struct device *dev, void __iomem *mmio)
{
int ret = 0;
unsigned int reg_val;
@@ -152,7 +202,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)
return 0;
}
-static void imx6q_sata_exit(struct device *dev)
+static void imx_sata_exit(struct device *dev)
{
imx_sata_clock_disable(dev);
}
@@ -182,16 +232,18 @@ static int imx_ahci_resume(struct device *dev)
return ret;
}
-static struct ahci_platform_data imx6q_sata_pdata = {
- .init = imx6q_sata_init,
- .exit = imx6q_sata_exit,
- .ata_port_info = &ahci_imx_port_info,
- .suspend = imx_ahci_suspend,
- .resume = imx_ahci_resume,
+static struct ahci_platform_data imx_sata_pdata = {
+ .init = imx_sata_init,
+ .exit = imx_sata_exit,
+ .ata_port_info = &ahci_imx_port_info,
+ .suspend = imx_ahci_suspend,
+ .resume = imx_ahci_resume,
+
};
static const struct of_device_id imx_ahci_of_match[] = {
- { .compatible = "fsl,imx6q-ahci", .data = &imx6q_sata_pdata},
+ { .compatible = "fsl,imx53-ahci", .data = (void *)AHCI_IMX53 },
+ { .compatible = "fsl,imx6q-ahci", .data = (void *)AHCI_IMX6Q },
{},
};
MODULE_DEVICE_TABLE(of, imx_ahci_of_match);
@@ -201,12 +253,20 @@ static int imx_ahci_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct resource *mem, *irq, res[2];
const struct of_device_id *of_id;
+ enum ahci_imx_type type;
const struct ahci_platform_data *pdata = NULL;
struct imx_ahci_priv *imxpriv;
struct device *ahci_dev;
struct platform_device *ahci_pdev;
int ret;
+ of_id = of_match_device(imx_ahci_of_match, dev);
+ if (!of_id)
+ return -EINVAL;
+
+ type = (enum ahci_imx_type)of_id->data;
+ pdata = &imx_sata_pdata;
+
imxpriv = devm_kzalloc(dev, sizeof(*imxpriv), GFP_KERNEL);
if (!imxpriv) {
dev_err(dev, "can't alloc ahci_host_priv\n");
@@ -222,6 +282,8 @@ static int imx_ahci_probe(struct platform_device *pdev)
imxpriv->no_device = false;
imxpriv->first_time = true;
+ imxpriv->type = type;
+
imxpriv->ahb_clk = devm_clk_get(dev, "ahb");
if (IS_ERR(imxpriv->ahb_clk)) {
dev_err(dev, "can't get ahb clock.\n");
@@ -229,6 +291,15 @@ static int imx_ahci_probe(struct platform_device *pdev)
goto err_out;
}
+ if (type == AHCI_IMX53) {
+ imxpriv->sata_gate_clk = devm_clk_get(dev, "sata_gate");
+ if (IS_ERR(imxpriv->sata_gate_clk)) {
+ dev_err(dev, "can't get sata_gate clock.\n");
+ ret = PTR_ERR(imxpriv->sata_gate_clk);
+ goto err_out;
+ }
+ }
+
imxpriv->sata_ref_clk = devm_clk_get(dev, "sata_ref");
if (IS_ERR(imxpriv->sata_ref_clk)) {
dev_err(dev, "can't get sata_ref clock.\n");
@@ -239,14 +310,6 @@ static int imx_ahci_probe(struct platform_device *pdev)
imxpriv->ahci_pdev = ahci_pdev;
platform_set_drvdata(pdev, imxpriv);
- of_id = of_match_device(imx_ahci_of_match, dev);
- if (of_id) {
- pdata = of_id->data;
- } else {
- ret = -EINVAL;
- goto err_out;
- }
-
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
if (!mem || !irq) {
@@ -262,41 +325,42 @@ static int imx_ahci_probe(struct platform_device *pdev)
ahci_dev->dma_mask = &ahci_dev->coherent_dma_mask;
ahci_dev->of_node = dev->of_node;
- imxpriv->gpr =
- syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
-
- if (IS_ERR(imxpriv->gpr)) {
- dev_err(dev, "failed to find fsl,imx6q-iomux-gpr regmap\n");
- ret = PTR_ERR(imxpriv->gpr);
- goto err_out;
+ if (type == AHCI_IMX6Q) {
+ imxpriv->gpr = syscon_regmap_lookup_by_compatible(
+ "fsl,imx6q-iomuxc-gpr");
+ if (IS_ERR(imxpriv->gpr)) {
+ dev_err(dev,
+ "failed to find fsl,imx6q-iomux-gpr regmap\n");
+ return PTR_ERR(imxpriv->gpr);
+ }
+
+ /*
+ * Set PHY Paremeters, two steps to configure the GPR13,
+ * one write for rest of parameters, mask of first write
+ * is 0x07fffffe, and the other one write for setting
+ * the mpll_clk_en happens in imx_sata_clock_enable().
+ */
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK |
+ IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK |
+ IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK |
+ IMX6Q_GPR13_SATA_SPD_MODE_MASK |
+ IMX6Q_GPR13_SATA_MPLL_SS_EN |
+ IMX6Q_GPR13_SATA_TX_ATTEN_MASK |
+ IMX6Q_GPR13_SATA_TX_BOOST_MASK |
+ IMX6Q_GPR13_SATA_TX_LVL_MASK |
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN |
+ IMX6Q_GPR13_SATA_TX_EDGE_RATE,
+ IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB |
+ IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M |
+ IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F |
+ IMX6Q_GPR13_SATA_SPD_MODE_3P0G |
+ IMX6Q_GPR13_SATA_MPLL_SS_EN |
+ IMX6Q_GPR13_SATA_TX_ATTEN_9_16 |
+ IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB |
+ IMX6Q_GPR13_SATA_TX_LVL_1_025_V);
}
- /*
- * Set PHY Paremeters, two steps to configure the GPR13,
- * one write for rest of parameters, mask of first write
- * is 0x07ffffff, and the other one write for setting
- * the mpll_clk_en happens in imx_sata_clock_enable().
- */
- regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
- IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK |
- IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK |
- IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK |
- IMX6Q_GPR13_SATA_SPD_MODE_MASK |
- IMX6Q_GPR13_SATA_MPLL_SS_EN |
- IMX6Q_GPR13_SATA_TX_ATTEN_MASK |
- IMX6Q_GPR13_SATA_TX_BOOST_MASK |
- IMX6Q_GPR13_SATA_TX_LVL_MASK |
- IMX6Q_GPR13_SATA_MPLL_CLK_EN |
- IMX6Q_GPR13_SATA_TX_EDGE_RATE,
- IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB |
- IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M |
- IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F |
- IMX6Q_GPR13_SATA_SPD_MODE_3P0G |
- IMX6Q_GPR13_SATA_MPLL_SS_EN |
- IMX6Q_GPR13_SATA_TX_ATTEN_9_16 |
- IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB |
- IMX6Q_GPR13_SATA_TX_LVL_1_025_V);
-
ret = platform_device_add_resources(ahci_pdev, res, 2);
if (ret)
goto err_out;
--
1.8.4.3
^ permalink raw reply related [flat|nested] 11+ messages in thread