From: sboyd@codeaurora.org (Stephen Boyd)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] regmap: Allow regmap_bulk_read() to work for "no-bus" regmaps
Date: Fri, 13 Dec 2013 09:14:07 -0800 [thread overview]
Message-ID: <20131213171407.GN21983@codeaurora.org> (raw)
In-Reply-To: <20131213104128.GT11044@sirena.org.uk>
regmap_bulk_read() should decay to performing individual reads if
we're using a "no-bus" regmap. Unfortunately, it returns an
error because there is no map->bus pointer. Fix it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
On 12/13/13 02:41, Mark Brown wrote:
> On Thu, Dec 12, 2013 at 03:13:01PM -0800, Stephen Boyd wrote:
>
>>> bulk_read() should decay to individual reads if there isn't a block
>>> operaton and it's not like the hardware actually supports bulk reads
>>> anyway.
>
>> So regmap_bulk_read() should work if I don't have a map->bus? To make it
>> work with reg_read/write I had to do this. I'm not sure how to make
>> bulk_write work.
>
> Yes, I'd expect the operation to work. Your changes below are mostly
> fine (we should add an additional check for values that aren't integer
> numbers of bytes, I can add that) - can you send as a signed off patch
> please and I'll apply?
Here you go. Do you have any suggestions on how to make regmap_bulk_write()
work?
drivers/base/regmap/regmap.c | 6 +-----
1 file changed, 1 insertion(+), 5 deletions(-)
diff --git a/drivers/base/regmap/regmap.c b/drivers/base/regmap/regmap.c
index 9c021d9..1ccd61b 100644
--- a/drivers/base/regmap/regmap.c
+++ b/drivers/base/regmap/regmap.c
@@ -1897,14 +1897,10 @@ int regmap_bulk_read(struct regmap *map, unsigned int reg, void *val,
size_t val_bytes = map->format.val_bytes;
bool vol = regmap_volatile_range(map, reg, val_count);
- if (!map->bus)
- return -EINVAL;
- if (!map->format.parse_inplace)
- return -EINVAL;
if (reg % map->reg_stride)
return -EINVAL;
- if (vol || map->cache_type == REGCACHE_NONE) {
+ if (map->bus && map->format.parse_inplace && (vol || map->cache_type == REGCACHE_NONE)) {
/*
* Some devices does not support bulk read, for
* them we have a series of single read operations.
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
next prev parent reply other threads:[~2013-12-13 17:14 UTC|newest]
Thread overview: 37+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-12-10 23:35 [PATCH 0/8] Modernize pm8921 with irqdomains + regmap Stephen Boyd
2013-12-10 23:35 ` [PATCH 1/8] mfd: ssbi: Remove platform data structs and hide ssbi type enum Stephen Boyd
2013-12-11 9:27 ` Lee Jones
2013-12-10 23:35 ` [PATCH 2/8] mfd: ssbi: Constify buffer in ssbi_write Stephen Boyd
2013-12-11 9:28 ` Lee Jones
2013-12-10 23:35 ` [PATCH 3/8] regmap: Add support for using regmap over ssbi Stephen Boyd
2013-12-10 23:50 ` Mark Brown
2013-12-11 0:13 ` Stephen Boyd
2013-12-11 0:51 ` Mark Brown
2013-12-11 1:32 ` Stephen Boyd
2013-12-11 13:27 ` Mark Brown
2013-12-12 23:13 ` Stephen Boyd
2013-12-13 10:41 ` Mark Brown
2013-12-13 17:14 ` Stephen Boyd [this message]
2013-12-16 20:57 ` [PATCH] regmap: Allow regmap_bulk_read() to work for "no-bus" regmaps Mark Brown
2013-12-13 21:37 ` [PATCH 3/8] regmap: Add support for using regmap over ssbi Stephen Boyd
2013-12-16 21:01 ` Mark Brown
2013-12-17 2:30 ` [PATCH] regmap: Allow regmap_bulk_write() to work for "no-bus" regmaps Stephen Boyd
2013-12-18 18:45 ` Mark Brown
2013-12-23 20:05 ` Stephen Boyd
2013-12-24 12:53 ` Mark Brown
2013-12-26 19:34 ` Stephen Boyd
2013-12-26 21:52 ` [PATCH v2] " Stephen Boyd
2013-12-30 12:42 ` Mark Brown
2013-12-10 23:35 ` [PATCH 4/8] mfd: ssbi: Mark match table const Stephen Boyd
2013-12-11 9:29 ` Lee Jones
2013-12-10 23:35 ` [PATCH 5/8] mfd: Move pm8xxx-irq.c contents into only driver that uses it Stephen Boyd
2013-12-11 9:35 ` Lee Jones
2013-12-12 19:06 ` Stephen Boyd
2013-12-10 23:35 ` [PATCH 6/8] mfd: pm8921: Update for genirq changes Stephen Boyd
2013-12-11 9:48 ` Lee Jones
2013-12-10 23:35 ` [PATCH 7/8] mfd: pm8921: Migrate to irqdomains Stephen Boyd
2013-12-11 9:53 ` Lee Jones
2013-12-11 21:30 ` Courtney Cavin
2013-12-12 19:05 ` Stephen Boyd
2013-12-10 23:35 ` [PATCH 8/8] mfd: pm8921: Use ssbi regmap Stephen Boyd
2013-12-11 9:55 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20131213171407.GN21983@codeaurora.org \
--to=sboyd@codeaurora.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).