linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: andrew@lunn.ch (Andrew Lunn)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: orion: provide C-style interrupt handler for MULTI_IRQ_HANDLER
Date: Thu, 16 Jan 2014 16:19:27 +0100	[thread overview]
Message-ID: <20140116151927.GN17530@lunn.ch> (raw)
In-Reply-To: <1389859831-9883-1-git-send-email-sebastian.hesselbarth@gmail.com>

On Thu, Jan 16, 2014 at 09:10:31AM +0100, Sebastian Hesselbarth wrote:
> DT-enabled Marvell Kirkwood and Dove SoCs make use of an irqchip
> driver. As expected for irqchip drivers, it uses a C-style
> interrupt handler and therefore selects MULTI_IRQ_HANDLER.
> 
> Now, compiling a kernel with both non-DT and DT support enabled,
> selecting MULTI_IRQ_HANDLER will break ASM irq handler used by
> non-DT boards.
> 
> Therefore, we provide a C-style irq handler even for non-DT boards,
> if MULTI_IRQ_HANDLER is set. By installing the C-style irq handler
> in orion_irq_init this is transparent to all non-DT board files.
> 
> While the regression report was filed on Marvell Kirkwood, also
> Marvell Dove non-DT boards are affected and fixed by this patch.
> 
> Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
> Tested-by: Ian Campbell <ijc@hellion.org.uk>
> Reported-by: Ian Campbell <ijc@hellion.org.uk>
> Fixes: 2326f04321a9 ("ARM: kirkwood: convert to DT irqchip and clocksource")
> Fixes: f07d73e33d0e ("ARM: dove: convert to DT irqchip and clocksource")

Hi Sebastian

Makes sense and this version is much better than the previous.

Acked-by: Andrew Lunn <andrew@lunn.ch>

	  Andrew


> ---
> Compared to the two patch version sent on Ian's regression report,
> I cooked this down to a single patch only touching plat-orion/irq.c.
> I also dropped Orion5x and MV78x00, as they not yet select MULTI_IRQ_HANDLER
> at all. Instead I added a comment about taking care of them, as soon as
> they move over to an irqchip driver themselves.
> 
> I have not yet Cc'ed this patch to -stable to get some discussion and
> an Acked-by from Jason or Andrew, too.
> 
> Cc: Jason Cooper <jason@lakedaemon.net>
> Cc: Andrew Lunn <andrew@lunn.ch>
> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
> Cc: Russell King <linux@arm.linux.org.uk>
> Cc: Ian Campbell <ijc@hellion.org.uk>
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: linux-kernel at vger.kernel.org
> ---
>  arch/arm/plat-orion/irq.c | 47 +++++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 47 insertions(+)
> 
> diff --git a/arch/arm/plat-orion/irq.c b/arch/arm/plat-orion/irq.c
> index c492e1b3dfdb..807df142444b 100644
> --- a/arch/arm/plat-orion/irq.c
> +++ b/arch/arm/plat-orion/irq.c
> @@ -15,8 +15,51 @@
>  #include <linux/io.h>
>  #include <linux/of_address.h>
>  #include <linux/of_irq.h>
> +#include <asm/exception.h>
>  #include <plat/irq.h>
>  #include <plat/orion-gpio.h>
> +#include <mach/bridge-regs.h>
> +
> +#ifdef CONFIG_MULTI_IRQ_HANDLER
> +/*
> + * Compiling with both non-DT and DT support enabled, will
> + * break asm irq handler used by non-DT boards. Therefore,
> + * we provide a C-style irq handler even for non-DT boards,
> + * if MULTI_IRQ_HANDLER is set.
> + *
> + * Notes:
> + * - this is prepared for Kirkwood and Dove only, update
> + *   accordingly if you add Orion5x or MV78x00.
> + * - Orion5x uses different macro names and has only one
> + *   set of CAUSE/MASK registers.
> + * - MV78x00 uses the same macro names but has a third
> + *   set of CAUSE/MASK registers.
> + *
> + */
> +
> +static void __iomem *orion_irq_base = IRQ_VIRT_BASE;
> +
> +asmlinkage void
> +__exception_irq_entry orion_legacy_handle_irq(struct pt_regs *regs)
> +{
> +	u32 stat;
> +
> +	stat = readl_relaxed(orion_irq_base + IRQ_CAUSE_LOW_OFF);
> +	stat &= readl_relaxed(orion_irq_base + IRQ_MASK_LOW_OFF);
> +	if (stat) {
> +		unsigned int hwirq = __fls(stat);
> +		handle_IRQ(hwirq, regs);
> +		return;
> +	}
> +	stat = readl_relaxed(orion_irq_base + IRQ_CAUSE_HIGH_OFF);
> +	stat &= readl_relaxed(orion_irq_base + IRQ_MASK_HIGH_OFF);
> +	if (stat) {
> +		unsigned int hwirq = 32 + __fls(stat);
> +		handle_IRQ(hwirq, regs);
> +		return;
> +	}
> +}
> +#endif
>  
>  void __init orion_irq_init(unsigned int irq_start, void __iomem *maskaddr)
>  {
> @@ -35,6 +78,10 @@ void __init orion_irq_init(unsigned int irq_start, void __iomem *maskaddr)
>  	ct->chip.irq_unmask = irq_gc_mask_set_bit;
>  	irq_setup_generic_chip(gc, IRQ_MSK(32), IRQ_GC_INIT_MASK_CACHE,
>  			       IRQ_NOREQUEST, IRQ_LEVEL | IRQ_NOPROBE);
> +
> +#ifdef CONFIG_MULTI_IRQ_HANDLER
> +	set_handle_irq(orion_legacy_handle_irq);
> +#endif
>  }
>  
>  #ifdef CONFIG_OF
> -- 
> 1.8.5.2
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply	other threads:[~2014-01-16 15:19 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-01-15  8:40 v3.12 regression from "ARM: kirkwood: convert to DT irqchip and clocksource" on non-DT kirkwood platforms Ian Campbell
2014-01-15  9:15 ` Sebastian Hesselbarth
2014-01-15  9:26   ` Ian Campbell
2014-01-15 19:54     ` Sebastian Hesselbarth
2014-01-15 20:15       ` Ian Campbell
2014-01-16  8:10 ` [PATCH] ARM: orion: provide C-style interrupt handler for MULTI_IRQ_HANDLER Sebastian Hesselbarth
2014-01-16 15:19   ` Andrew Lunn [this message]
2014-01-16 16:48   ` Jason Cooper
2014-01-16 16:51     ` Ian Campbell
2014-01-16 16:53       ` Jason Cooper
2014-01-16 18:42         ` Sebastian Hesselbarth
2014-01-16 18:49           ` Jason Cooper
2014-01-20 21:53             ` Ian Campbell

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20140116151927.GN17530@lunn.ch \
    --to=andrew@lunn.ch \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).