* [PATCH v2 1/5] ARM: Kirkwood: Add audio node to kirkwood.dtsi
2014-02-24 18:01 [PATCH v2 0/5] mvebu support for kirkwood HP T5325 Andrew Lunn
@ 2014-02-24 18:01 ` Andrew Lunn
2014-02-24 19:03 ` Jason Cooper
2014-02-24 18:01 ` [PATCH v2 2/5] ARM: mvebu: Add i2c alias so setting bus number Andrew Lunn
` (3 subsequent siblings)
4 siblings, 1 reply; 15+ messages in thread
From: Andrew Lunn @ 2014-02-24 18:01 UTC (permalink / raw)
To: linux-arm-kernel
The binding has existed for a while, so add the missing node so it can
be used by devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
v2:
Tabify
---
arch/arm/boot/dts/kirkwood.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index 7b921b30cfcb..180dc69ff742 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -310,5 +310,14 @@
#phy-cells = <0>;
status = "ok";
};
+
+ audio0: audio-controller at a0000 {
+ compatible = "marvell,kirkwood-audio";
+ reg = <0xa0000 0x2210>;
+ interrupts = <24>;
+ clocks = <&gate_clk 9>;
+ clock-names = "internal";
+ status = "disabled";
+ };
};
};
--
1.8.5.3
^ permalink raw reply related [flat|nested] 15+ messages in thread* [PATCH v2 1/5] ARM: Kirkwood: Add audio node to kirkwood.dtsi
2014-02-24 18:01 ` [PATCH v2 1/5] ARM: Kirkwood: Add audio node to kirkwood.dtsi Andrew Lunn
@ 2014-02-24 19:03 ` Jason Cooper
0 siblings, 0 replies; 15+ messages in thread
From: Jason Cooper @ 2014-02-24 19:03 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Feb 24, 2014 at 07:01:34PM +0100, Andrew Lunn wrote:
> The binding has existed for a while, so add the missing node so it can
> be used by devices.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> ---
> v2:
> Tabify
> ---
> arch/arm/boot/dts/kirkwood.dtsi | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
> diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
> index 7b921b30cfcb..180dc69ff742 100644
> --- a/arch/arm/boot/dts/kirkwood.dtsi
> +++ b/arch/arm/boot/dts/kirkwood.dtsi
> @@ -310,5 +310,14 @@
> #phy-cells = <0>;
> status = "ok";
> };
> +
> + audio0: audio-controller at a0000 {
> + compatible = "marvell,kirkwood-audio";
> + reg = <0xa0000 0x2210>;
> + interrupts = <24>;
> + clocks = <&gate_clk 9>;
> + clock-names = "internal";
> + status = "disabled";
> + };
leading whitespace before brace.
thx,
Jason.
> };
> };
> --
> 1.8.5.3
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v2 2/5] ARM: mvebu: Add i2c alias so setting bus number
2014-02-24 18:01 [PATCH v2 0/5] mvebu support for kirkwood HP T5325 Andrew Lunn
2014-02-24 18:01 ` [PATCH v2 1/5] ARM: Kirkwood: Add audio node to kirkwood.dtsi Andrew Lunn
@ 2014-02-24 18:01 ` Andrew Lunn
2014-02-24 19:05 ` Jason Cooper
2014-02-24 18:01 ` [PATCH v2 3/5] ARM: mvebu: Add HP T5325 thin client Andrew Lunn
` (2 subsequent siblings)
4 siblings, 1 reply; 15+ messages in thread
From: Andrew Lunn @ 2014-02-24 18:01 UTC (permalink / raw)
To: linux-arm-kernel
When using platform_driver instantiation, the i2c bus was given bus
number 0. The kirkwood-t5325 audio driver has this bus number hard
coded for the address of the codec. However by default device tree i2c
busses are dynamically allocated a bus number, starting from 1. Thus
the kirkwood-t5325 cannot find its audio codec. By adding an alias in
the DT file we can control the bus number and set it to 0. The codec
can then be found.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/kirkwood.dtsi | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
index 180dc69ff742..d8e34fab835b 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/kirkwood.dtsi
@@ -24,6 +24,7 @@
aliases {
gpio0 = &gpio0;
gpio1 = &gpio1;
+ i2c0 = &i2c0;
};
mbus {
@@ -111,7 +112,7 @@
clocks = <&gate_clk 7>;
};
- i2c at 11000 {
+ i2c0: i2c at 11000 {
compatible = "marvell,mv64xxx-i2c";
reg = <0x11000 0x20>;
#address-cells = <1>;
--
1.8.5.3
^ permalink raw reply related [flat|nested] 15+ messages in thread* [PATCH v2 2/5] ARM: mvebu: Add i2c alias so setting bus number
2014-02-24 18:01 ` [PATCH v2 2/5] ARM: mvebu: Add i2c alias so setting bus number Andrew Lunn
@ 2014-02-24 19:05 ` Jason Cooper
2014-02-24 19:11 ` Andrew Lunn
0 siblings, 1 reply; 15+ messages in thread
From: Jason Cooper @ 2014-02-24 19:05 UTC (permalink / raw)
To: linux-arm-kernel
Subject should be "ARM: kirkwood: ..."
thx,
Jason.
On Mon, Feb 24, 2014 at 07:01:35PM +0100, Andrew Lunn wrote:
> When using platform_driver instantiation, the i2c bus was given bus
> number 0. The kirkwood-t5325 audio driver has this bus number hard
> coded for the address of the codec. However by default device tree i2c
> busses are dynamically allocated a bus number, starting from 1. Thus
> the kirkwood-t5325 cannot find its audio codec. By adding an alias in
> the DT file we can control the bus number and set it to 0. The codec
> can then be found.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> ---
> arch/arm/boot/dts/kirkwood.dtsi | 3 ++-
> 1 file changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi
> index 180dc69ff742..d8e34fab835b 100644
> --- a/arch/arm/boot/dts/kirkwood.dtsi
> +++ b/arch/arm/boot/dts/kirkwood.dtsi
> @@ -24,6 +24,7 @@
> aliases {
> gpio0 = &gpio0;
> gpio1 = &gpio1;
> + i2c0 = &i2c0;
> };
>
> mbus {
> @@ -111,7 +112,7 @@
> clocks = <&gate_clk 7>;
> };
>
> - i2c at 11000 {
> + i2c0: i2c at 11000 {
> compatible = "marvell,mv64xxx-i2c";
> reg = <0x11000 0x20>;
> #address-cells = <1>;
> --
> 1.8.5.3
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 15+ messages in thread* [PATCH v2 2/5] ARM: mvebu: Add i2c alias so setting bus number
2014-02-24 19:05 ` Jason Cooper
@ 2014-02-24 19:11 ` Andrew Lunn
2014-02-24 19:30 ` Jason Cooper
0 siblings, 1 reply; 15+ messages in thread
From: Andrew Lunn @ 2014-02-24 19:11 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Feb 24, 2014 at 02:05:09PM -0500, Jason Cooper wrote:
> Subject should be "ARM: kirkwood: ..."
Humm, why?
linux/arch/arm/boot/dts$ git log --oneline armada-370.dtsi
a095b1c78a35 ARM: mvebu: sort DT nodes by address
d4fa99417a07 ARM: mvebu: link PCIe controllers to the MSI controller
238493e34d3f ARM: dts: mvebu: Update with the new compatible string for mv64xxx-
6cbe0e1feaf8 Merge tag 'dt-3.12' of git://git.infradead.org/linux-mvebu into nex
5d3b88307176 ARM: mvebu: Fix the Armada 370/XP timer compatible strings
ca60985c0042 ARM: mvebu: use correct #interrupt-cells instead of #interrupts-cel
14fd8ed0a7fd ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes
0cd3754a8317 ARM: mvebu: Add BootROM to Armada 370/XP device tree
5e12a613ce39 ARM: mvebu: Add MBus to Armada 370/XP device tree
38149887ef8b ARM: mvebu: Use the preprocessor on Armada 370/XP device tree files
9214cbe50fe7 Merge tag 'dt-3.11-5' of git://git.infradead.org/users/jcooper/linu
83735101959e ARM: mvebu: Remove device tree unused properties on A370
489e138eec96 ARM: dts: mvebu: Fix wrong the address reg value for the L2-cache n
8eed481e6fe2 arm: mvebu: fix the 'ranges' property to handle PCIe
Seems to me, now that it is part of mach-mvebu, ARM: mvebu is correct.
Andrew
^ permalink raw reply [flat|nested] 15+ messages in thread* [PATCH v2 2/5] ARM: mvebu: Add i2c alias so setting bus number
2014-02-24 19:11 ` Andrew Lunn
@ 2014-02-24 19:30 ` Jason Cooper
2014-02-24 21:32 ` Arnd Bergmann
0 siblings, 1 reply; 15+ messages in thread
From: Jason Cooper @ 2014-02-24 19:30 UTC (permalink / raw)
To: linux-arm-kernel
Andrew,
+ arm-soc maintainers
On Mon, Feb 24, 2014 at 08:11:08PM +0100, Andrew Lunn wrote:
> On Mon, Feb 24, 2014 at 02:05:09PM -0500, Jason Cooper wrote:
> > Subject should be "ARM: kirkwood: ..."
>
> Humm, why?
>
> linux/arch/arm/boot/dts$ git log --oneline armada-370.dtsi
No, you're editing:
arch/arm/boot/dts/kirkwood.dtsi | 3 ++-
> a095b1c78a35 ARM: mvebu: sort DT nodes by address
> d4fa99417a07 ARM: mvebu: link PCIe controllers to the MSI controller
> 238493e34d3f ARM: dts: mvebu: Update with the new compatible string for mv64xxx-
> 6cbe0e1feaf8 Merge tag 'dt-3.12' of git://git.infradead.org/linux-mvebu into nex
> 5d3b88307176 ARM: mvebu: Fix the Armada 370/XP timer compatible strings
> ca60985c0042 ARM: mvebu: use correct #interrupt-cells instead of #interrupts-cel
> 14fd8ed0a7fd ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes
> 0cd3754a8317 ARM: mvebu: Add BootROM to Armada 370/XP device tree
> 5e12a613ce39 ARM: mvebu: Add MBus to Armada 370/XP device tree
> 38149887ef8b ARM: mvebu: Use the preprocessor on Armada 370/XP device tree files
> 9214cbe50fe7 Merge tag 'dt-3.11-5' of git://git.infradead.org/users/jcooper/linu
> 83735101959e ARM: mvebu: Remove device tree unused properties on A370
> 489e138eec96 ARM: dts: mvebu: Fix wrong the address reg value for the L2-cache n
> 8eed481e6fe2 arm: mvebu: fix the 'ranges' property to handle PCIe
>
> Seems to me, now that it is part of mach-mvebu, ARM: mvebu is correct.
"ARM: kirkwood: ..." is more helpful to someone searching --oneline for
changes to the kirkwood SoC.
So yeah, mvebu encompasses kirkwood now with your patchset. Which makes
the 'mvebu' term more vague. Before, folks could restrict commit
history on mach-kirkwood/ or mach-dove/ to see changes for a particular
SoC. With it all in mach-mvebu (and not in a single file), we need
another way for developers to spot relevant commits. That's why I
prefer the above.
ex: What changed from v3.15 to v3.16 for kirkwood?
$ git log --oneline v3.15..v3.16 -- arch/arm/mach-mvebu | \
grep -i 'ARM: kirkwood'
This seems to be new territory for us (mvebu), perhaps one of the
arm-soc maintainers has a preference? I'll add them to this reply.
thx,
Jason.
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v2 2/5] ARM: mvebu: Add i2c alias so setting bus number
2014-02-24 19:30 ` Jason Cooper
@ 2014-02-24 21:32 ` Arnd Bergmann
2014-02-24 22:15 ` Jason Cooper
0 siblings, 1 reply; 15+ messages in thread
From: Arnd Bergmann @ 2014-02-24 21:32 UTC (permalink / raw)
To: linux-arm-kernel
On Monday 24 February 2014, Jason Cooper wrote:
>
> ex: What changed from v3.15 to v3.16 for kirkwood?
>
> $ git log --oneline v3.15..v3.16 -- arch/arm/mach-mvebu | \
> grep -i 'ARM: kirkwood'
>
> This seems to be new territory for us (mvebu), perhaps one of the
> arm-soc maintainers has a preference? I'll add them to this reply.
I don't care, as long as you decide on something that works for you.
While you're transitioning, it probably makes little sense to
enforce either one too strictly.
Arnd
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v2 2/5] ARM: mvebu: Add i2c alias so setting bus number
2014-02-24 21:32 ` Arnd Bergmann
@ 2014-02-24 22:15 ` Jason Cooper
0 siblings, 0 replies; 15+ messages in thread
From: Jason Cooper @ 2014-02-24 22:15 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Feb 24, 2014 at 10:32:20PM +0100, Arnd Bergmann wrote:
> On Monday 24 February 2014, Jason Cooper wrote:
>
> >
> > ex: What changed from v3.15 to v3.16 for kirkwood?
> >
> > $ git log --oneline v3.15..v3.16 -- arch/arm/mach-mvebu | \
> > grep -i 'ARM: kirkwood'
> >
> > This seems to be new territory for us (mvebu), perhaps one of the
> > arm-soc maintainers has a preference? I'll add them to this reply.
>
> I don't care, as long as you decide on something that works for you.
Ok, we'll wait till we have an actual problem ;-) Seriously though,
once dove and kirkwood are both migrated, we'll sit down and hash out
how to handle it (if needed at all).
> While you're transitioning, it probably makes little sense to
> enforce either one too strictly.
Agreed. Andrew, let's stick with the previous pseudo-file/path standard
for now. If you're inclined, please change the dts patches to kirkwood.
If you don't feel like it, I'll only twitch a little bit. :)
thx,
Jason.
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v2 3/5] ARM: mvebu: Add HP T5325 thin client
2014-02-24 18:01 [PATCH v2 0/5] mvebu support for kirkwood HP T5325 Andrew Lunn
2014-02-24 18:01 ` [PATCH v2 1/5] ARM: Kirkwood: Add audio node to kirkwood.dtsi Andrew Lunn
2014-02-24 18:01 ` [PATCH v2 2/5] ARM: mvebu: Add i2c alias so setting bus number Andrew Lunn
@ 2014-02-24 18:01 ` Andrew Lunn
2014-02-24 19:10 ` Jason Cooper
2014-02-24 18:01 ` [PATCH v2 4/5] ARM: mvebu: Add dts file describing " Andrew Lunn
2014-02-24 18:01 ` [PATCH v2 5/5] ARM: mvebu: Add HP T5325 devices to {multi|mvebu}_v5_defconfig Andrew Lunn
4 siblings, 1 reply; 15+ messages in thread
From: Andrew Lunn @ 2014-02-24 18:01 UTC (permalink / raw)
To: linux-arm-kernel
Convert the kirkwood t5325-setup.c to mostly device tree for
mach-mvebu. Part of the audio setup needs to remain in C for the
moment until suitable bindings are designed and implemented. So add
board code, triggered by the compatibility string.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
v2:
Remove spaces around KEY_POWER
Correct indentation of help text in Kconfig.
Put dts file into a patch of its own.
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/mach-mvebu/Kconfig | 7 +++++++
arch/arm/mach-mvebu/Makefile | 1 +
arch/arm/mach-mvebu/board-t5325.c | 41 +++++++++++++++++++++++++++++++++++++++
arch/arm/mach-mvebu/board.h | 22 +++++++++++++++++++++
arch/arm/mach-mvebu/kirkwood.c | 11 ++++++++++-
6 files changed, 82 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/mach-mvebu/board-t5325.c
create mode 100644 arch/arm/mach-mvebu/board.h
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 436cc381db4a..20c152faa800 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -132,6 +132,7 @@ kirkwood := \
kirkwood-rs411.dtb \
kirkwood-sheevaplug.dtb \
kirkwood-sheevaplug-esata.dtb \
+ kirkwood-t5325.dtb \
kirkwood-topkick.dtb \
kirkwood-ts219-6281.dtb \
kirkwood-ts219-6282.dtb \
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index 529f9164a8ca..5de7ada19191 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -92,6 +92,13 @@ config MACH_KIRKWOOD
Say 'Y' here if you want your kernel to support boards based
on the Marvell Kirkwood device tree.
+config MACH_T5325
+ bool "HP T5325 thin client"
+ depends on MACH_KIRKWOOD
+ help
+ Say 'Y' here if you want your kernel to support the
+ HP T5325 Thin client
+
endmenu
endif
diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
index d7672f1c8a6a..bbeb41ee3e75 100644
--- a/arch/arm/mach-mvebu/Makefile
+++ b/arch/arm/mach-mvebu/Makefile
@@ -9,3 +9,4 @@ obj-$(CONFIG_ARCH_MVEBU) += coherency.o coherency_ll.o pmsu.o
obj-$(CONFIG_SMP) += platsmp.o headsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
obj-$(CONFIG_MACH_KIRKWOOD) += kirkwood.o kirkwood-pm.o
+obj-$(CONFIG_MACH_T5325) += board-t5325.o
diff --git a/arch/arm/mach-mvebu/board-t5325.c b/arch/arm/mach-mvebu/board-t5325.c
new file mode 100644
index 000000000000..65ace6db9f28
--- /dev/null
+++ b/arch/arm/mach-mvebu/board-t5325.c
@@ -0,0 +1,41 @@
+/*
+ * HP T5325 Board Setup
+ *
+ * Copyright (C) 2014
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <sound/alc5623.h>
+#include "board.h"
+
+static struct platform_device hp_t5325_audio_device = {
+ .name = "t5325-audio",
+ .id = -1,
+};
+
+static struct alc5623_platform_data alc5621_data = {
+ .add_ctrl = 0x3700,
+ .jack_det_ctrl = 0x4810,
+};
+
+static struct i2c_board_info i2c_board_info[] __initdata = {
+ {
+ I2C_BOARD_INFO("alc5621", 0x1a),
+ .platform_data = &alc5621_data,
+ },
+};
+
+void __init t5325_init(void)
+{
+ i2c_register_board_info(0, i2c_board_info, ARRAY_SIZE(i2c_board_info));
+ platform_device_register(&hp_t5325_audio_device);
+}
diff --git a/arch/arm/mach-mvebu/board.h b/arch/arm/mach-mvebu/board.h
new file mode 100644
index 000000000000..de7f0a191394
--- /dev/null
+++ b/arch/arm/mach-mvebu/board.h
@@ -0,0 +1,22 @@
+/*
+ * Board functions for Marvell System On Chip
+ *
+ * Copyright (C) 2014
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ARCH_MVEBU_BOARD_H
+#define __ARCH_MVEBU_BOARD_H
+
+#ifdef CONFIG_MACH_T5325
+void t5325_init(void);
+#else
+static inline void t5325_init(void) {};
+#endif
+
+#endif
diff --git a/arch/arm/mach-mvebu/kirkwood.c b/arch/arm/mach-mvebu/kirkwood.c
index 8a38b10532e5..120207fc36f1 100644
--- a/arch/arm/mach-mvebu/kirkwood.c
+++ b/arch/arm/mach-mvebu/kirkwood.c
@@ -25,6 +25,7 @@
#include "kirkwood.h"
#include "kirkwood-pm.h"
#include "common.h"
+#include "board.h"
static struct resource kirkwood_cpufreq_resources[] = {
[0] = {
@@ -158,6 +159,11 @@ void kirkwood_disable_mbus_error_propagation(void)
writel(readl(cpu_config) & ~CPU_CONFIG_ERROR_PROP, cpu_config);
}
+static struct of_dev_auxdata auxdata[] __initdata = {
+ OF_DEV_AUXDATA("marvell,kirkwood-audio", 0xf10a0000,
+ "mvebu-audio", NULL),
+ { /* sentinel */ }
+};
static void __init kirkwood_dt_init(void)
{
@@ -174,7 +180,10 @@ static void __init kirkwood_dt_init(void)
kirkwood_pm_init();
kirkwood_dt_eth_fixup();
- of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+ if (of_machine_is_compatible("hp,t5325"))
+ t5325_init();
+
+ of_platform_populate(NULL, of_default_bus_match_table, auxdata, NULL);
}
static const char * const kirkwood_dt_board_compat[] = {
--
1.8.5.3
^ permalink raw reply related [flat|nested] 15+ messages in thread* [PATCH v2 3/5] ARM: mvebu: Add HP T5325 thin client
2014-02-24 18:01 ` [PATCH v2 3/5] ARM: mvebu: Add HP T5325 thin client Andrew Lunn
@ 2014-02-24 19:10 ` Jason Cooper
2014-02-24 19:12 ` Andrew Lunn
0 siblings, 1 reply; 15+ messages in thread
From: Jason Cooper @ 2014-02-24 19:10 UTC (permalink / raw)
To: linux-arm-kernel
Subject should be "ARM: kirkwood: ..."
On Mon, Feb 24, 2014 at 07:01:36PM +0100, Andrew Lunn wrote:
> Convert the kirkwood t5325-setup.c to mostly device tree for
> mach-mvebu. Part of the audio setup needs to remain in C for the
> moment until suitable bindings are designed and implemented. So add
> board code, triggered by the compatibility string.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> ---
> v2:
> Remove spaces around KEY_POWER
> Correct indentation of help text in Kconfig.
> Put dts file into a patch of its own.
> ---
> arch/arm/boot/dts/Makefile | 1 +
This Makefile change should be in the same patch as the one adding the
dts file.
thx,
Jason.
> arch/arm/mach-mvebu/Kconfig | 7 +++++++
> arch/arm/mach-mvebu/Makefile | 1 +
> arch/arm/mach-mvebu/board-t5325.c | 41 +++++++++++++++++++++++++++++++++++++++
> arch/arm/mach-mvebu/board.h | 22 +++++++++++++++++++++
> arch/arm/mach-mvebu/kirkwood.c | 11 ++++++++++-
> 6 files changed, 82 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/mach-mvebu/board-t5325.c
> create mode 100644 arch/arm/mach-mvebu/board.h
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 436cc381db4a..20c152faa800 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -132,6 +132,7 @@ kirkwood := \
> kirkwood-rs411.dtb \
> kirkwood-sheevaplug.dtb \
> kirkwood-sheevaplug-esata.dtb \
> + kirkwood-t5325.dtb \
> kirkwood-topkick.dtb \
> kirkwood-ts219-6281.dtb \
> kirkwood-ts219-6282.dtb \
> diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
> index 529f9164a8ca..5de7ada19191 100644
> --- a/arch/arm/mach-mvebu/Kconfig
> +++ b/arch/arm/mach-mvebu/Kconfig
> @@ -92,6 +92,13 @@ config MACH_KIRKWOOD
> Say 'Y' here if you want your kernel to support boards based
> on the Marvell Kirkwood device tree.
>
> +config MACH_T5325
> + bool "HP T5325 thin client"
> + depends on MACH_KIRKWOOD
> + help
> + Say 'Y' here if you want your kernel to support the
> + HP T5325 Thin client
> +
> endmenu
>
> endif
> diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
> index d7672f1c8a6a..bbeb41ee3e75 100644
> --- a/arch/arm/mach-mvebu/Makefile
> +++ b/arch/arm/mach-mvebu/Makefile
> @@ -9,3 +9,4 @@ obj-$(CONFIG_ARCH_MVEBU) += coherency.o coherency_ll.o pmsu.o
> obj-$(CONFIG_SMP) += platsmp.o headsmp.o
> obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
> obj-$(CONFIG_MACH_KIRKWOOD) += kirkwood.o kirkwood-pm.o
> +obj-$(CONFIG_MACH_T5325) += board-t5325.o
> diff --git a/arch/arm/mach-mvebu/board-t5325.c b/arch/arm/mach-mvebu/board-t5325.c
> new file mode 100644
> index 000000000000..65ace6db9f28
> --- /dev/null
> +++ b/arch/arm/mach-mvebu/board-t5325.c
> @@ -0,0 +1,41 @@
> +/*
> + * HP T5325 Board Setup
> + *
> + * Copyright (C) 2014
> + *
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/platform_device.h>
> +#include <sound/alc5623.h>
> +#include "board.h"
> +
> +static struct platform_device hp_t5325_audio_device = {
> + .name = "t5325-audio",
> + .id = -1,
> +};
> +
> +static struct alc5623_platform_data alc5621_data = {
> + .add_ctrl = 0x3700,
> + .jack_det_ctrl = 0x4810,
> +};
> +
> +static struct i2c_board_info i2c_board_info[] __initdata = {
> + {
> + I2C_BOARD_INFO("alc5621", 0x1a),
> + .platform_data = &alc5621_data,
> + },
> +};
> +
> +void __init t5325_init(void)
> +{
> + i2c_register_board_info(0, i2c_board_info, ARRAY_SIZE(i2c_board_info));
> + platform_device_register(&hp_t5325_audio_device);
> +}
> diff --git a/arch/arm/mach-mvebu/board.h b/arch/arm/mach-mvebu/board.h
> new file mode 100644
> index 000000000000..de7f0a191394
> --- /dev/null
> +++ b/arch/arm/mach-mvebu/board.h
> @@ -0,0 +1,22 @@
> +/*
> + * Board functions for Marvell System On Chip
> + *
> + * Copyright (C) 2014
> + *
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#ifndef __ARCH_MVEBU_BOARD_H
> +#define __ARCH_MVEBU_BOARD_H
> +
> +#ifdef CONFIG_MACH_T5325
> +void t5325_init(void);
> +#else
> +static inline void t5325_init(void) {};
> +#endif
> +
> +#endif
> diff --git a/arch/arm/mach-mvebu/kirkwood.c b/arch/arm/mach-mvebu/kirkwood.c
> index 8a38b10532e5..120207fc36f1 100644
> --- a/arch/arm/mach-mvebu/kirkwood.c
> +++ b/arch/arm/mach-mvebu/kirkwood.c
> @@ -25,6 +25,7 @@
> #include "kirkwood.h"
> #include "kirkwood-pm.h"
> #include "common.h"
> +#include "board.h"
>
> static struct resource kirkwood_cpufreq_resources[] = {
> [0] = {
> @@ -158,6 +159,11 @@ void kirkwood_disable_mbus_error_propagation(void)
> writel(readl(cpu_config) & ~CPU_CONFIG_ERROR_PROP, cpu_config);
> }
>
> +static struct of_dev_auxdata auxdata[] __initdata = {
> + OF_DEV_AUXDATA("marvell,kirkwood-audio", 0xf10a0000,
> + "mvebu-audio", NULL),
> + { /* sentinel */ }
> +};
>
> static void __init kirkwood_dt_init(void)
> {
> @@ -174,7 +180,10 @@ static void __init kirkwood_dt_init(void)
> kirkwood_pm_init();
> kirkwood_dt_eth_fixup();
>
> - of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
> + if (of_machine_is_compatible("hp,t5325"))
> + t5325_init();
> +
> + of_platform_populate(NULL, of_default_bus_match_table, auxdata, NULL);
> }
>
> static const char * const kirkwood_dt_board_compat[] = {
> --
> 1.8.5.3
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 15+ messages in thread* [PATCH v2 3/5] ARM: mvebu: Add HP T5325 thin client
2014-02-24 19:10 ` Jason Cooper
@ 2014-02-24 19:12 ` Andrew Lunn
0 siblings, 0 replies; 15+ messages in thread
From: Andrew Lunn @ 2014-02-24 19:12 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Feb 24, 2014 at 02:10:14PM -0500, Jason Cooper wrote:
> Subject should be "ARM: kirkwood: ..."
I disagree, but lets discuss that with the other patch.
>
> On Mon, Feb 24, 2014 at 07:01:36PM +0100, Andrew Lunn wrote:
> > Convert the kirkwood t5325-setup.c to mostly device tree for
> > mach-mvebu. Part of the audio setup needs to remain in C for the
> > moment until suitable bindings are designed and implemented. So add
> > board code, triggered by the compatibility string.
> >
> > Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> > ---
> > v2:
> > Remove spaces around KEY_POWER
> > Correct indentation of help text in Kconfig.
> > Put dts file into a patch of its own.
> > ---
> > arch/arm/boot/dts/Makefile | 1 +
>
> This Makefile change should be in the same patch as the one adding the
> dts file.
Agreed. Will fix.
Andrew
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v2 4/5] ARM: mvebu: Add dts file describing HP T5325 thin client
2014-02-24 18:01 [PATCH v2 0/5] mvebu support for kirkwood HP T5325 Andrew Lunn
` (2 preceding siblings ...)
2014-02-24 18:01 ` [PATCH v2 3/5] ARM: mvebu: Add HP T5325 thin client Andrew Lunn
@ 2014-02-24 18:01 ` Andrew Lunn
2014-02-24 19:15 ` Jason Cooper
2014-02-24 18:01 ` [PATCH v2 5/5] ARM: mvebu: Add HP T5325 devices to {multi|mvebu}_v5_defconfig Andrew Lunn
4 siblings, 1 reply; 15+ messages in thread
From: Andrew Lunn @ 2014-02-24 18:01 UTC (permalink / raw)
To: linux-arm-kernel
Describe the T5325 using device tree properties, where possible. The
first version of this file was produced by Thomas Petazzoni.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/kirkwood-t5325.dts | 209 +++++++++++++++++++++++++++++++++++
1 file changed, 209 insertions(+)
create mode 100644 arch/arm/boot/dts/kirkwood-t5325.dts
diff --git a/arch/arm/boot/dts/kirkwood-t5325.dts b/arch/arm/boot/dts/kirkwood-t5325.dts
new file mode 100644
index 000000000000..8df357d822ca
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-t5325.dts
@@ -0,0 +1,209 @@
+/*
+ * Device Tree file for HP t5325 Thin Client"
+ *
+ * Copyright (C) 2014
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+*/
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "HP t5325 Thin Client";
+ compatible = "hp,t5325", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ mbus {
+ pcie-controller {
+ status = "okay";
+
+ pcie at 1,0 {
+ status = "okay";
+ };
+ };
+ };
+
+ ocp at f1000000 {
+ pinctrl: pinctrl at 10000 {
+ pinctrl-0 = <&pmx_i2s &pmx_sysrst>;
+ pinctrl-names = "default";
+
+ pmx_button_power: pmx-button_power {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ pmx_power_off: pmx-power-off {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+
+ pmx_led: pmx-led {
+ marvell,pins = "mpp21";
+ marvell,function = "gpio";
+ };
+
+ pmx_usb_sata_power_enable: pmx-usb-sata-power-enable {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+
+ /*
+ * Redefined from kirkwood-6281.dtsi, because
+ * we don't use SPI CS on MPP0, but on MPP7.
+ */
+ pmx_spi: pmx-spi {
+ marvell,pins = "mpp1", "mpp2", "mpp3", "mpp7";
+ marvell,function = "spi";
+ };
+
+ pmx_sysrst: pmx-sysrst {
+ marvell,pins = "mpp6";
+ marvell,function = "sysrst";
+ };
+
+ pmx_i2s: pmx-i2s {
+ marvell,pins = "mpp39", "mpp40", "mpp41", "mpp42",
+ "mpp43";
+ marvell,function = "audio";
+ };
+ };
+
+ spi at 10600 {
+ pinctrl-0 = <&pmx_spi>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p80";
+ spi-max-frequency = <86000000>;
+ reg = <0>;
+ mode = <0>;
+
+ partition at 0 {
+ reg = <0x0 0x80000>;
+ label = "u-boot";
+ };
+
+ partition at 1 {
+ reg = <0x80000 0x40000>;
+ label = "SSD firmware";
+ };
+
+ partition at 2 {
+ reg = <0xc0000 0x10000>;
+ label = "u-boot env";
+ };
+
+ partition at 3 {
+ reg = <0xd0000 0x10000>;
+ label = "permanent u-boot env";
+ };
+
+ partition at 4 {
+ reg = <0xd0000 0x10000>;
+ label = "permanent u-boot env";
+ };
+ };
+ };
+
+ i2c at 11000 {
+ status = "okay";
+
+ alc5621: alc5621 at 1a {
+ compatible = "realtek,alc5621";
+ reg = <0x1a>;
+ };
+ };
+
+ serial at 12000 {
+ status = "okay";
+ };
+
+ sata at 80000 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+
+ audio: audio-controller at a0000 {
+ status = "okay";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_sata_power_enable>;
+ pinctrl-names = "default";
+
+ usb_power: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB-SATA Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_button_power>;
+ pinctrl-names = "default";
+
+ button at 1 {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&pmx_power_off>;
+ pinctrl-names = "default";
+ gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+ };
+
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy {
+ device_type = "ethernet-phy";
+ reg = <8>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port at 0 {
+ phy-handle = <ðphy0>;
+ };
+};
+
--
1.8.5.3
^ permalink raw reply related [flat|nested] 15+ messages in thread* [PATCH v2 4/5] ARM: mvebu: Add dts file describing HP T5325 thin client
2014-02-24 18:01 ` [PATCH v2 4/5] ARM: mvebu: Add dts file describing " Andrew Lunn
@ 2014-02-24 19:15 ` Jason Cooper
0 siblings, 0 replies; 15+ messages in thread
From: Jason Cooper @ 2014-02-24 19:15 UTC (permalink / raw)
To: linux-arm-kernel
Subject should be "ARM: kirkwood: ..."
On Mon, Feb 24, 2014 at 07:01:37PM +0100, Andrew Lunn wrote:
> Describe the T5325 using device tree properties, where possible. The
> first version of this file was produced by Thomas Petazzoni.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> ---
> arch/arm/boot/dts/kirkwood-t5325.dts | 209 +++++++++++++++++++++++++++++++++++
> 1 file changed, 209 insertions(+)
> create mode 100644 arch/arm/boot/dts/kirkwood-t5325.dts
>
> diff --git a/arch/arm/boot/dts/kirkwood-t5325.dts b/arch/arm/boot/dts/kirkwood-t5325.dts
> new file mode 100644
> index 000000000000..8df357d822ca
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-t5325.dts
> @@ -0,0 +1,209 @@
> +/*
> + * Device Tree file for HP t5325 Thin Client"
> + *
> + * Copyright (C) 2014
> + *
> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> + * Andrew Lunn <andrew@lunn.ch>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> +*/
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +
> +/ {
> + model = "HP t5325 Thin Client";
> + compatible = "hp,t5325", "marvell,kirkwood-88f6281", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x20000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + };
> +
> + mbus {
> + pcie-controller {
> + status = "okay";
> +
> + pcie at 1,0 {
> + status = "okay";
> + };
> + };
> + };
> +
> + ocp at f1000000 {
> + pinctrl: pinctrl at 10000 {
> + pinctrl-0 = <&pmx_i2s &pmx_sysrst>;
> + pinctrl-names = "default";
> +
> + pmx_button_power: pmx-button_power {
> + marvell,pins = "mpp45";
> + marvell,function = "gpio";
> + };
> +
> + pmx_power_off: pmx-power-off {
> + marvell,pins = "mpp48";
> + marvell,function = "gpio";
> + };
> +
> + pmx_led: pmx-led {
> + marvell,pins = "mpp21";
> + marvell,function = "gpio";
> + };
> +
> + pmx_usb_sata_power_enable: pmx-usb-sata-power-enable {
> + marvell,pins = "mpp44";
> + marvell,function = "gpio";
> + };
> +
> + /*
> + * Redefined from kirkwood-6281.dtsi, because
> + * we don't use SPI CS on MPP0, but on MPP7.
> + */
wonky leading whitespace.
> + pmx_spi: pmx-spi {
> + marvell,pins = "mpp1", "mpp2", "mpp3", "mpp7";
> + marvell,function = "spi";
> + };
> +
> + pmx_sysrst: pmx-sysrst {
> + marvell,pins = "mpp6";
> + marvell,function = "sysrst";
> + };
> +
> + pmx_i2s: pmx-i2s {
> + marvell,pins = "mpp39", "mpp40", "mpp41", "mpp42",
> + "mpp43";
> + marvell,function = "audio";
> + };
> + };
> +
> + spi at 10600 {
> + pinctrl-0 = <&pmx_spi>;
> + pinctrl-names = "default";
> + status = "okay";
> +
> + flash at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "st,m25p80";
> + spi-max-frequency = <86000000>;
> + reg = <0>;
> + mode = <0>;
> +
> + partition at 0 {
> + reg = <0x0 0x80000>;
> + label = "u-boot";
> + };
> +
> + partition at 1 {
> + reg = <0x80000 0x40000>;
> + label = "SSD firmware";
> + };
> +
> + partition at 2 {
> + reg = <0xc0000 0x10000>;
> + label = "u-boot env";
> + };
> +
> + partition at 3 {
> + reg = <0xd0000 0x10000>;
> + label = "permanent u-boot env";
> + };
> +
> + partition at 4 {
> + reg = <0xd0000 0x10000>;
> + label = "permanent u-boot env";
> + };
> + };
> + };
> +
> + i2c at 11000 {
> + status = "okay";
> +
> + alc5621: alc5621 at 1a {
> + compatible = "realtek,alc5621";
> + reg = <0x1a>;
> + };
> + };
> +
> + serial at 12000 {
> + status = "okay";
> + };
> +
> + sata at 80000 {
> + status = "okay";
> + nr-ports = <2>;
> + };
> +
> + audio: audio-controller at a0000 {
> + status = "okay";
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_usb_sata_power_enable>;
> + pinctrl-names = "default";
> +
> + usb_power: regulator at 1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "USB-SATA Power";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + regulator-boot-on;
> + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-0 = <&pmx_button_power>;
> + pinctrl-names = "default";
> +
> + button at 1 {
> + label = "Power Button";
> + linux,code = <KEY_POWER>;
> + gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + gpio_poweroff {
> + compatible = "gpio-poweroff";
> + pinctrl-0 = <&pmx_power_off>;
> + pinctrl-names = "default";
> + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
> + };
> +
> +};
> +
> +&mdio {
> + status = "okay";
> +
> + ethphy0: ethernet-phy {
> + device_type = "ethernet-phy";
> + reg = <8>;
leading whitespace again.
thx,
Jason.
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> + ethernet0-port at 0 {
> + phy-handle = <ðphy0>;
> + };
> +};
> +
> --
> 1.8.5.3
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v2 5/5] ARM: mvebu: Add HP T5325 devices to {multi|mvebu}_v5_defconfig
2014-02-24 18:01 [PATCH v2 0/5] mvebu support for kirkwood HP T5325 Andrew Lunn
` (3 preceding siblings ...)
2014-02-24 18:01 ` [PATCH v2 4/5] ARM: mvebu: Add dts file describing " Andrew Lunn
@ 2014-02-24 18:01 ` Andrew Lunn
4 siblings, 0 replies; 15+ messages in thread
From: Andrew Lunn @ 2014-02-24 18:01 UTC (permalink / raw)
To: linux-arm-kernel
The HP T5325 has a PCI based VGA controller. Add the frame buffer
driver, and frame buffer support to the defconfig's. Additionally
add the soc audio framework and the necessary codec.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/configs/multi_v5_defconfig | 9 +++++++++
arch/arm/configs/mvebu_v5_defconfig | 9 +++++++++
2 files changed, 18 insertions(+)
diff --git a/arch/arm/configs/multi_v5_defconfig b/arch/arm/configs/multi_v5_defconfig
index 2bc1e1707930..84ba24a0ead7 100644
--- a/arch/arm/configs/multi_v5_defconfig
+++ b/arch/arm/configs/multi_v5_defconfig
@@ -11,6 +11,7 @@ CONFIG_MODULE_UNLOAD=y
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_MVEBU=y
CONFIG_MACH_KIRKWOOD=y
+CONFIG_MACH_T5325=y
CONFIG_ARCH_MXC=y
CONFIG_MACH_IMX25_DT=y
CONFIG_MACH_IMX27_DT=y
@@ -101,6 +102,12 @@ CONFIG_THERMAL=y
CONFIG_KIRKWOOD_THERMAL=y
CONFIG_WATCHDOG=y
CONFIG_ORION_WATCHDOG=y
+CONFIG_FB=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SOC=y
+CONFIG_SND_KIRKWOOD_SOC=y
+CONFIG_SND_KIRKWOOD_SOC_T5325=y
# CONFIG_ABX500_CORE is not set
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
@@ -150,6 +157,8 @@ CONFIG_RTC_DRV_S35390A=y
CONFIG_RTC_DRV_MV=y
CONFIG_DMADEVICES=y
CONFIG_MV_XOR=y
+CONFIG_STAGING=y
+CONFIG_FB_XGI=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
diff --git a/arch/arm/configs/mvebu_v5_defconfig b/arch/arm/configs/mvebu_v5_defconfig
index 2844636c0cf2..36484a37a1ca 100644
--- a/arch/arm/configs/mvebu_v5_defconfig
+++ b/arch/arm/configs/mvebu_v5_defconfig
@@ -11,6 +11,7 @@ CONFIG_MODULE_UNLOAD=y
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_MVEBU=y
CONFIG_MACH_KIRKWOOD=y
+CONFIG_MACH_T5325=y
# CONFIG_CPU_FEROCEON_OLD_ID is not set
CONFIG_PCI_MVEBU=y
CONFIG_PREEMPT=y
@@ -93,6 +94,12 @@ CONFIG_SENSORS_LM85=y
CONFIG_THERMAL=y
CONFIG_WATCHDOG=y
CONFIG_ORION_WATCHDOG=y
+CONFIG_FB=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_SOC=y
+CONFIG_SND_KIRKWOOD_SOC=y
+CONFIG_SND_KIRKWOOD_SOC_T5325=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_HID_DRAGONRISE=y
@@ -137,6 +144,8 @@ CONFIG_RTC_DRV_S35390A=y
CONFIG_RTC_DRV_MV=y
CONFIG_DMADEVICES=y
CONFIG_MV_XOR=y
+CONFIG_STAGING=y
+CONFIG_FB_XGI=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
--
1.8.5.3
^ permalink raw reply related [flat|nested] 15+ messages in thread