[PATCH v3 09/18] ASoC: fsl-ssi: Only enable baudclk when used

[Guangyu.Chen@freescale.com (Nicolin Chen)]

On Mon, Apr 14, 2014 at 03:35:39PM +0200, Markus Pargmann wrote:
> From: Sascha Hauer <s.hauer@pengutronix.de>
> 
> Enable baudclk only when it is used. The baudclock is only needed in master
> mode and only when thr driver is active, so move enabling to fsl_ssi_startup
> and disabling to fsl_ssi_shutdown.
> 
> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
> ---
>  sound/soc/fsl/fsl_ssi.c | 37 ++++++++++++++++++++++++++++++-------
>  1 file changed, 30 insertions(+), 7 deletions(-)
> 
> diff --git a/sound/soc/fsl/fsl_ssi.c b/sound/soc/fsl/fsl_ssi.c
> index f2255cb..d6d3f0a3 100644
> --- a/sound/soc/fsl/fsl_ssi.c
> +++ b/sound/soc/fsl/fsl_ssi.c
> @@ -236,6 +236,12 @@ static bool fsl_ssi_is_ac97(struct fsl_ssi_private *ssi_private)
>  	return !!(ssi_private->dai_fmt & SND_SOC_DAIFMT_AC97);
>  }
>  
> +static bool fsl_ssi_is_i2s_master(struct fsl_ssi_private *ssi_private)
> +{
> +	return (ssi_private->dai_fmt & SND_SOC_DAIFMT_MASTER_MASK) ==
> +		SND_SOC_DAIFMT_CBS_CFS;
> +}
> +
>  /**
>   * fsl_ssi_isr: SSI interrupt handler
>   *
> @@ -489,6 +495,7 @@ static int fsl_ssi_startup(struct snd_pcm_substream *substream,
>  	struct fsl_ssi_private *ssi_private =
>  		snd_soc_dai_get_drvdata(rtd->cpu_dai);
>  	unsigned long flags;
> +	int ret;
>  
>  	if (!dai->active && !fsl_ssi_is_ac97(ssi_private)) {
>  		spin_lock_irqsave(&ssi_private->baudclk_lock, flags);
> @@ -496,6 +503,12 @@ static int fsl_ssi_startup(struct snd_pcm_substream *substream,
>  		spin_unlock_irqrestore(&ssi_private->baudclk_lock, flags);
>  	}
>  
> +	if (fsl_ssi_is_i2s_master(ssi_private)) {
> +		ret = clk_prepare_enable(ssi_private->baudclk);
> +		if (ret)
> +			return ret;
> +	}
> +
>  	/* When using dual fifo mode, it is safer to ensure an even period
>  	 * size. If appearing to an odd number while DMA always starts its
>  	 * task from fifo0, fifo1 would be neglected at the end of each
> @@ -508,6 +521,17 @@ static int fsl_ssi_startup(struct snd_pcm_substream *substream,
>  	return 0;
>  }
>  
> +static void fsl_ssi_shutdown(struct snd_pcm_substream *substream,
> +		struct snd_soc_dai *dai)
> +{
> +	struct snd_soc_pcm_runtime *rtd = substream->private_data;
> +	struct fsl_ssi_private *ssi_private =
> +		snd_soc_dai_get_drvdata(rtd->cpu_dai);
> +
> +	if (fsl_ssi_is_i2s_master(ssi_private))
> +		clk_disable_unprepare(ssi_private->baudclk);
> +}
> +
>  /**
>   * fsl_ssi_hw_params - program the sample size
>   *
> @@ -576,6 +600,11 @@ static int fsl_ssi_set_dai_fmt(struct snd_soc_dai *cpu_dai, unsigned int fmt)
>  
>  	ssi_private->dai_fmt = fmt;
>  
> +	if (fsl_ssi_is_i2s_master(ssi_private) && IS_ERR(ssi_private->baudclk)) {
> +		dev_err(cpu_dai->dev, "no baudclk needed for master mode\n");
> +		return -EINVAL;
> +	}
> +

I was wondering what if machine driver doesn't set fmt to master during
its probe(), in another word -- before fsl_ssi_startup(), but leave that
into its hw_params() via snd_soc_dai_set_fmt() which then would run after
fsl_ssi_startup() while having no baud clock enabled in this case.

A better solution may be to wrap clk_prepare_enable() and master mode
clock dividing code into fsl_ssi_hw_params(), a bit like the ESAI driver
even though it doesn't contain the clk_prepare_enable() part currently,
and then to put clk_disable_unprepare() into hw_free() for symmetry.

Any suggestion?

Thank you,
Nicolin

>  	fsl_ssi_setup_reg_vals(ssi_private);
>  
>  	scr = read_ssi(&ssi->scr) & ~(CCSR_SSI_SCR_SYN | CCSR_SSI_SCR_I2S_MODE_MASK);
> @@ -910,6 +939,7 @@ static int fsl_ssi_dai_probe(struct snd_soc_dai *dai)
>  
>  static const struct snd_soc_dai_ops fsl_ssi_dai_ops = {
>  	.startup	= fsl_ssi_startup,
> +	.shutdown	= fsl_ssi_shutdown,
>  	.hw_params	= fsl_ssi_hw_params,
>  	.set_fmt	= fsl_ssi_set_dai_fmt,
>  	.set_sysclk	= fsl_ssi_set_dai_sysclk,
> @@ -1050,8 +1080,6 @@ static int fsl_ssi_imx_probe(struct platform_device *pdev,
>  	if (IS_ERR(ssi_private->baudclk))
>  		dev_dbg(&pdev->dev, "could not get baud clock: %ld\n",
>  			 PTR_ERR(ssi_private->baudclk));
> -	else
> -		clk_prepare_enable(ssi_private->baudclk);
>  
>  	/*
>  	 * We have burstsize be "fifo_depth - 2" to match the SSI
> @@ -1102,9 +1130,6 @@ static int fsl_ssi_imx_probe(struct platform_device *pdev,
>  	return 0;
>  
>  error_pcm:
> -	if (!IS_ERR(ssi_private->baudclk))
> -		clk_disable_unprepare(ssi_private->baudclk);
> -
>  	clk_disable_unprepare(ssi_private->clk);
>  
>  	return ret;
> @@ -1115,8 +1140,6 @@ static void fsl_ssi_imx_clean(struct platform_device *pdev,
>  {
>  	if (!ssi_private->use_dma)
>  		imx_pcm_fiq_exit(pdev);
> -	if (!IS_ERR(ssi_private->baudclk))
> -		clk_disable_unprepare(ssi_private->baudclk);
>  	clk_disable_unprepare(ssi_private->clk);
>  }
>  
> -- 
> 1.9.1
> 
> 
>