[PATCH] ARM: at91/dt: at91sam9m10g45ek add rtc node

[boris.brezillon@free-electrons.com (Boris BREZILLON)]

On Wed, 03 Sep 2014 08:09:28 +0200
Erik van Luijk <evanluijk@interact.nl> wrote:

> 
> Hi Boris, Nicolas,
> 
> Boris BREZILLON schreef op 2-9-2014 om 18:33:
> > Hi Erik,
>  >
>  > On Tue,  2 Sep 2014 12:52:12 +0200
>  > Erik van Luijk <evanluijk@interact.nl> wrote:
>  >
>  >> Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
>  >
>  > Except for the nitpicks you'll find below, you have my
>  >
>  > Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
>  >
>  >> ---
>  >>  arch/arm/boot/dts/at91sam9g45.dtsi     | 7 +++++++
>  >>  arch/arm/boot/dts/at91sam9m10g45ek.dts | 3 +++
>  >>  2 files changed, 10 insertions(+)
>  >>
>  >> diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi 
> b/arch/arm/boot/dts/at91sam9g45.dtsi
>  >> index 932a669..bf62c18 100644
>  >> --- a/arch/arm/boot/dts/at91sam9g45.dtsi
>  >> +++ b/arch/arm/boot/dts/at91sam9g45.dtsi
>  >> @@ -1070,6 +1070,13 @@
>  >>                  status = "disabled";
>  >>              };
>  >>
>  >> +            rtc at fffffdb0 {
>  >> +                compatible = "atmel,at91rm9200-rtc";
>  >> +                reg = <0xfffffdb0 0x30>;
>  >
>  > The RTC registers goes from 0xfffffdb0 to 0xfffffdc0, which means the
>  > size is 0x10 and not 0x30. This is not important here, because the
>  > following region is marked as reserved, but we prefer to keep the DT
>  > consistent with the datasheet.
> 
> This is an inconsistency in the datasheet of the AT91SAM9G45 (and at 
> least also
> AT91SAM9G15, AT91SAM9G25, AT91SAM9G35 and AT91SAM9M10).
> In the memory map (fig. 5-1) there is room for 16 bytes.
> But in the 'Real-time Clock (RTC) User Interface' (table 15-1) there is 
> room for
> 48 bytes (0x30) excluding the Reserved Registers (which don't belong to 
> the RTC
> on the AT91SAM9M10). Perhaps Nicolas can draw some attention to this at 
> Atmel.

Indeed, I only had a look at the memory map.
Given this input, you should keep your definition ;-).

> 
> >
>  >> +                interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>  >> +                status = "disabled";
>  >> +            };
>  >> +
>  >>              spi0: spi at fffa4000 {
>  >>                  #address-cells = <1>;
>  >>                  #size-cells = <0>;
>  >> diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts 
> b/arch/arm/boot/dts/at91sam9m10g45ek.dts
>  >> index 96ccc7d..2dd2347 100644
>  >> --- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
>  >> +++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
>  >> @@ -70,6 +70,9 @@
>  >>
>  >>              watchdog at fffffd40 {
>  >>                  status = "okay";
>  >> +
>  >> +            rtc at fffffdb0 {
>  >> +                status = "okay";
>  >
>  > Try to keep SoC and board changes in distinct commits.
> 
> Understood.
> 
> >
>  >>              };
>  >>
>  >>              mmc0: mmc at fff80000 {
>  >
>  >
>  > Best Regards,
>  >
>  > Boris
>  >
> 
> Regards,
> 
> Erik



-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com