[PATCH v1 3/3] ARM: dts: imx6x: Add enet2 support for imx6sx-sdb board

[shawn.guo@freescale.com (Shawn Guo)]

On Sun, Sep 28, 2014 at 11:34:39AM +0800, Duan Fugang-B38611 wrote:
> From: Guo Shawn-R65073 Sent: Sunday, September 28, 2014 11:29 AM + 0800
> >To: Duan Fugang-B38611
> >Cc: linux-arm-kernel at lists.infradead.org; b20596 at solarflare.com;
> >shawn.guo at linaro.org; kernel at pengutronix.de
> >Subject: Re: [PATCH v1 3/3] ARM: dts: imx6x: Add enet2 support for imx6sx-
> >sdb board
> >
> >On Wed, Sep 24, 2014 at 10:11:20AM +0800, Fugang Duan wrote:
> >> Add enet2 support for imx6sx-sdb board, and add the "fsl,imx6q-fec"
> >> compatible for fec2 node to be compatible with the old version.
> >>
> >> Signed-off-by: Fugang Duan <B38611@freescale.com>
> >> ---
> >>  arch/arm/boot/dts/imx6sx-sdb.dts |   28 ++++++++++++++++++++++++++++
> >>  arch/arm/boot/dts/imx6sx.dtsi    |    2 +-
> >>  2 files changed, 29 insertions(+), 1 deletions(-)
> >>
> >> diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts
> >> b/arch/arm/boot/dts/imx6sx-sdb.dts
> >> index 82d6b34..06e0977 100644
> >> --- a/arch/arm/boot/dts/imx6sx-sdb.dts
> >> +++ b/arch/arm/boot/dts/imx6sx-sdb.dts
> >> @@ -133,6 +133,14 @@
> >>  &fec1 {
> >>  	pinctrl-names = "default";
> >>  	pinctrl-0 = <&pinctrl_enet1>;
> >> +	pinctrl-assert-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>, <&gpio2 6
> >> +GPIO_ACTIVE_LOW>;
> >
> >I do not think this property is supported by upstream kernel.
> The upstream kernel how to handle it ?

What are the purpose of these two GPIOs?

> 
> >
> >> +	phy-mode = "rgmii";
> >> +	status = "okay";
> >> +};
> >> +
> >> +&fec2 {
> >> +	pinctrl-names = "default";
> >> +	pinctrl-0 = <&pinctrl_enet2>;
> >>  	phy-mode = "rgmii";
> >>  	status = "okay";
> >>  };
> >> @@ -394,6 +402,26 @@
> >>  				MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2	0x3081
> >>  				MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3	0x3081
> >>  				MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN	0x3081
> >> +				MX6SX_PAD_QSPI1A_DATA0__GPIO4_IO_16	0x80000000
> >> +				MX6SX_PAD_QSPI1A_DATA3__GPIO4_IO_19	0x80000000
> >> +				MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M	0x91
> >> +			>;
> >> +		};
> >> +
> >> +		pinctrl_enet2: enet2grp {
> >> +			fsl,pins = <
> >> +				MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC	0xa0b9
> >> +				MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0	0xa0b1
> >> +				MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1	0xa0b1
> >> +				MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2	0xa0b1
> >> +				MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3	0xa0b1
> >> +				MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN	0xa0b1
> >> +				MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK	0x3081
> >> +				MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0	0x3081
> >> +				MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1	0x3081
> >> +				MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2	0x3081
> >> +				MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3	0x3081
> >> +				MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN	0x3081
> >>  			>;
> >>  		};
> >>
> >> diff --git a/arch/arm/boot/dts/imx6sx.dtsi
> >> b/arch/arm/boot/dts/imx6sx.dtsi index 888dd76..5a36053 100644
> >> --- a/arch/arm/boot/dts/imx6sx.dtsi
> >> +++ b/arch/arm/boot/dts/imx6sx.dtsi
> >> @@ -875,7 +875,7 @@
> >>  			};
> >>
> >>  			fec2: ethernet at 021b4000 {
> >> -				compatible = "fsl,imx6sx-fec";
> >> +				compatible = "fsl,imx6sx-fec", "fsl,imx6q-fec";
> >
> >Why is this change is necessary?  If "fsl,imx6sx-fec" is supported by
> >driver, it can be matched.
> >
> >Shawn
> - I want to let it align with fec1 compatible
> - Your tree still have no imx6sx enet patch, so fec2 will don't work at your tree. But the ip
>   Is compatible with imx6q-fec, so add the compatible.

Okay.

Shawn

> 
> >
> >>  				reg = <0x021b4000 0x4000>;
> >>  				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
> >>  					     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
> >> --
> >> 1.7.8
> >>
> 
> Thanks,
> Andy