[PATCH v2] imx: thermal: imx_get_temp might be called before sensor clock is prepared

[u.kleine-koenig@pengutronix.de (Uwe Kleine-König)]

On Wed, Oct 08, 2014 at 07:48:45AM +0200, Heiner Kallweit wrote:
> imx_get_temp might be called before the sensor clock is prepared thus
> resulting in a timeout of the first attempt to read temp:
> thermal thermal_zone0: failed to read out thermal zone 0
> Happened to me on a Utilite Standard with IMX6 Dual SoC.
> 
> Reason is that in imx_thermal_probe thermal_zone_device_register
> is called before the sensor clock is prepared.
> thermal_zone_device_register however calls
> thermal_zone_device_update which eventually calls imx_get_temp.
> 
> Fix this by preparing the clock before calling
> thermal_zone_device_register.
> 
> v2: revised error path. Bail out and tidy up properly if we can't
> get the clock or fail to enable it.
This paragraph usually goes below the "---".

> 
> Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
> ---
>  drivers/thermal/imx_thermal.c | 39 +++++++++++++++++++++++----------------
>  1 file changed, 23 insertions(+), 16 deletions(-)
> 
> diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
> index 461bf3d..faf5d88 100644
> --- a/drivers/thermal/imx_thermal.c
> +++ b/drivers/thermal/imx_thermal.c
> @@ -521,6 +521,28 @@ static int imx_thermal_probe(struct platform_device *pdev)
>                 return ret;
>         }
> 
> +       data->thermal_clk = devm_clk_get(&pdev->dev, NULL);
> +       if (IS_ERR(data->thermal_clk)) {
> +               ret = PTR_ERR(data->thermal_clk);
> +               dev_err(&pdev->dev, "failed to get thermal clk: %d\n", ret);
I think you don't want to print that error if ret == -EPROBE_DEFER.

> +               cpufreq_cooling_unregister(data->cdev);
> +               return ret;
> +       }
> +
> +       /*
> +        * Thermal sensor needs clk on to get correct value, normally
> +        * we should enable its clk before taking measurement and disable
> +        * clk after measurement is done, but if alarm function is enabled,
> +        * hardware will auto measure the temperature periodically, so we
> +        * need to keep the clk always on for alarm function.
> +        */
> +       ret = clk_prepare_enable(data->thermal_clk);
> +       if (ret) {
> +               dev_err(&pdev->dev, "failed to enable thermal clk: %d\n", ret);
> +               cpufreq_cooling_unregister(data->cdev);
> +               return ret;
> +       }
> +
>         data->tz = thermal_zone_device_register("imx_thermal_zone",
>                                                 IMX_TRIP_NUM,
>                                                 BIT(IMX_TRIP_PASSIVE), data,
> @@ -531,26 +553,11 @@ static int imx_thermal_probe(struct platform_device *pdev)
>                 ret = PTR_ERR(data->tz);
>                 dev_err(&pdev->dev,
>                         "failed to register thermal zone device %d\n", ret);
> +               clk_disable_unprepare(data->thermal_clk);
>                 cpufreq_cooling_unregister(data->cdev);
>                 return ret;
>         }
> 
> -       data->thermal_clk = devm_clk_get(&pdev->dev, NULL);
> -       if (IS_ERR(data->thermal_clk)) {
> -               dev_warn(&pdev->dev, "failed to get thermal clk!\n");
> -       } else {
> -               /*
> -                * Thermal sensor needs clk on to get correct value, normally
> -                * we should enable its clk before taking measurement and disable
> -                * clk after measurement is done, but if alarm function is enabled,
> -                * hardware will auto measure the temperature periodically, so we
> -                * need to keep the clk always on for alarm function.
> -                */
> -               ret = clk_prepare_enable(data->thermal_clk);
> -               if (ret)
> -                       dev_warn(&pdev->dev, "failed to enable thermal clk: %d\n", ret);
> -       }
> -
>         /* Enable measurements at ~ 10 Hz */
>         regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ);
>         measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */
> --
> 2.1.2
> 

-- 
Pengutronix e.K.                           | Uwe Kleine-K?nig            |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |