linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: maxime.ripard@free-electrons.com (Maxime Ripard)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 08/10] ARM: dts: sun9i: Enable mmc0 on A80 Optimus Board
Date: Sun, 7 Dec 2014 16:02:49 +0100	[thread overview]
Message-ID: <20141207150249.GG12434@lukather> (raw)
In-Reply-To: <1417588565-26215-9-git-send-email-wens@csie.org>

Hi,

On Wed, Dec 03, 2014 at 02:36:03PM +0800, Chen-Yu Tsai wrote:
> Enable the micro-sd slot on the A80 Optimus Board, which is connected to
> mmc0. This adds the card-detect gpio and enables mmc0.
> 
> This patch also adds a 3V fixed regulator, which is the default I/O
> voltage level.
> 
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> Signed-off-by: Andreas F?rber <afaerber@suse.de>
> ---
>  arch/arm/boot/dts/sun9i-a80-optimus.dts | 24 ++++++++++++++++++++++++
>  1 file changed, 24 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/sun9i-a80-optimus.dts
> index 506948f..02a4aa7 100644
> --- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
> +++ b/arch/arm/boot/dts/sun9i-a80-optimus.dts
> @@ -59,6 +59,16 @@
>  	};
>  
>  	soc {
> +		mmc0: mmc at 01c0f000 {
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
> +			vmmc-supply = <&reg_vcc3v0>;
> +			bus-width = <4>;
> +			cd-gpios = <&pio 7 18 0>; /* PH8 */
> +			cd-inverted;
> +			status = "okay";
> +		};
> +
>  		pio: pinctrl at 06000800 {
>  			i2c3_pins_a: i2c3 at 0 {
>  				/* Enable internal pull-up */
> @@ -72,6 +82,13 @@
>  				allwinner,pull = <0>;
>  			};
>  
> +			mmc0_cd_pin_optimus: mmc0_cd_pin at 0 {
> +				allwinner,pins = "PH18";
> +				allwinner,function = "gpio_in";
> +				allwinner,drive = <0>;
> +				allwinner,pull = <1>;
> +			};
> +
>  			uart4_pins_a: uart4 at 0 {
>  				/* Enable internal pull-up */
>  				allwinner,pull = <1>;
> @@ -116,4 +133,11 @@
>  			gpios = <&pio 7 0 0>;
>  		};
>  	};
> +
> +	reg_vcc3v0: vcc3v0 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc3v0";
> +		regulator-min-microvolt = <3000000>;
> +		regulator-max-microvolt = <3000000>;
> +	};

There's already such a regulator in sunxi-common-regulators.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20141207/9d729f61/attachment.sig>

  reply	other threads:[~2014-12-07 15:02 UTC|newest]

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-12-03  6:35 [PATCH 00/10] ARM: sun9i: Enable MMC support on Allwinner A80 Chen-Yu Tsai
2014-12-03  6:35 ` [PATCH 01/10] clk: sunxi: Add module 0 (storage) style clock support for A80 Chen-Yu Tsai
2014-12-06 17:13   ` Maxime Ripard
2014-12-07  1:13     ` [linux-sunxi] " Chen-Yu Tsai
2014-12-07 15:16       ` Maxime Ripard
2014-12-03  6:35 ` [PATCH 02/10] ARM: dts: sun9i: Add mmc module clock nodes " Chen-Yu Tsai
2014-12-06 17:24   ` Maxime Ripard
2014-12-07  1:11     ` Chen-Yu Tsai
2014-12-07 15:14       ` Maxime Ripard
2014-12-03  6:35 ` [PATCH 03/10] clk: sunxi: Add driver for A80 MMC config clocks/resets Chen-Yu Tsai
2014-12-06 18:01   ` Maxime Ripard
2014-12-07  1:30     ` Chen-Yu Tsai
2014-12-07 15:20       ` Maxime Ripard
2014-12-03  6:35 ` [PATCH 04/10] ARM: dts: sun9i: Add clock-indices property for bus gate clocks Chen-Yu Tsai
2014-12-03  6:36 ` [PATCH 05/10] ARM: dts: sun9i: Add mmc config clock nodes Chen-Yu Tsai
2014-12-07 15:00   ` Maxime Ripard
2014-12-07 16:00     ` Chen-Yu Tsai
2014-12-07 17:45       ` Maxime Ripard
2014-12-03  6:36 ` [PATCH 06/10] ARM: dts: sun9i: Add mmc controller nodes to the A80 dtsi Chen-Yu Tsai
2014-12-03  6:36 ` [PATCH 07/10] ARM: dts: sun9i: Add pinmux setting for mmc0 Chen-Yu Tsai
2014-12-07 15:01   ` Maxime Ripard
2014-12-03  6:36 ` [PATCH 08/10] ARM: dts: sun9i: Enable mmc0 on A80 Optimus Board Chen-Yu Tsai
2014-12-07 15:02   ` Maxime Ripard [this message]
2014-12-07 15:18     ` Chen-Yu Tsai
2014-12-07 15:35       ` Maxime Ripard
2014-12-03  6:36 ` [PATCH 09/10] ARM: dts: sun9i: Add pinmux settings for mmc2 Chen-Yu Tsai
2014-12-07 15:03   ` Maxime Ripard
2014-12-07 15:11     ` Chen-Yu Tsai
2014-12-07 17:46       ` Maxime Ripard
2014-12-03  6:36 ` [PATCH 10/10] ARM: dts: sun9i: Enable mmc2 on A80 Optimus Board Chen-Yu Tsai

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20141207150249.GG12434@lukather \
    --to=maxime.ripard@free-electrons.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).