From mboxrd@z Thu Jan 1 00:00:00 1970 From: u.kleine-koenig@pengutronix.de (Uwe =?iso-8859-1?Q?Kleine-K=F6nig?=) Date: Sun, 21 Dec 2014 11:29:25 +0100 Subject: kernel.org - master not booting on keystone (ARM v7 Cortex A15 SoC) EVMs In-Reply-To: <5494B932.6060602@ti.com> References: <549490D6.3090804@ti.com> <20141219211816.GH10857@pengutronix.de> <5494B932.6060602@ti.com> Message-ID: <20141221102925.GJ10857@pengutronix.de> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org Hello, I cannot say anything here, but maybe the people being involved in 1e6b48116a950 can. I added them to Cc and didn't trim the mail for them. Best regards Uwe On Fri, Dec 19, 2014 at 06:48:02PM -0500, Murali Karicheri wrote: > On 12/19/2014 04:25 PM, Tyler Baker wrote: > >Hello, > > > >On 19 December 2014 at 13:18, Uwe Kleine-K?nig > > wrote: > >>Hello, > >> > >>On Fri, Dec 19, 2014 at 03:55:50PM -0500, Murali Karicheri wrote: > >>>I have pulled the latest master from > >>>git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git and > >>>tried booting on keystone k2hk and k2e EVM. The boot hangs with > >>>following log. Has anyone seen this? Keystone is an ARM v7 cortex > >>>A15 SMP platform. I am assuming master branch is broken for ARM v7 > >>>and someone is working to address this. v3.18 booted up fine on my > >>>EVM. > >>> > >>>Any idea? > >>You forgot to attach the log?! So no, I don't have any idea. Did you > >>bisect? > > This was my first git bisect work. git bisect showed me below commit > as bad commit. But it is pretty old commit. I tried reverting the > commit and my board booted up fine. The boot log attached below. I > did following until I got the bad commit. v3.18 also worked fine. > > git bisect start > git bisect good > git bisect bad > > I build and test. If boots fine, I did git bisect good and if not, > git bisect bad until I got the bad commit. Can someone comment if my > bisect steps look sane? If so, what is wrong with the below commit? > Ours is a LPAE SoC. > > commit 1e6b48116a95046ec51f3d40f83aff8b006674d7 > Author: Kees Cook > Date: Thu Apr 3 17:28:11 2014 -0700 > > ARM: mm: allow non-text sections to be non-executable > > Adds CONFIG_ARM_KERNMEM_PERMS to separate the kernel memory regions > into section-sized areas that can have different permisions. Performs > the NX permission changes during free_initmem, so that init > memory can be > reclaimed. > > This uses section size instead of PMD size to reduce memory lost to > padding on non-LPAE systems. > > Based on work by Brad Spengler, Larry Bassel, and Laura Abbott. > > Signed-off-by: Kees Cook > Tested-by: Laura Abbott > Acked-by: Nicolas Pitre > > Bytes transferred = 3934208 (3c0800 hex) > ## installed monitor, freq [208333333], status 0 > ## Booting kernel from Legacy Image at 88000000 ... > Image Name: Linux-3.18.0-11757-gd790be3-dirt > Created: 2014-12-19 23:14:58 UTC > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 3934144 Bytes = 3.8 MiB > Load Address: 80008000 > Entry Point: 80008000 > Verifying Checksum ... OK > ## Flattened Device Tree blob at 87000000 > Booting using the fdt blob at 0x87000000 > Loading Kernel Image ... OK > Using Device Tree in place at 87000000, end 8700781d > > Starting kernel ... > > [ 0.000000] Booting Linux on physical CPU 0x0 > [ 0.000000] Linux version 3.18.0-11757-gd790be3-dirty > (a0868495 at ares-ubuntu) (gcc version 4.7.3 20130226 (prerelease) > (crosstool-NG linaro-1.13.1-4.7-2013.03-20130313 - Linaro GCC > 2013.03) ) #16 SMP PREEMPT Fri Dec 19 18:14:46 EST 2014 > [ 0.000000] CPU: ARMv7 Processor [412fc0f4] revision 4 (ARMv7), > cr=30c5387d > [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT > instruction cache > [ 0.000000] Machine model: Texas Instruments Keystone 2 Edison EVM > [ 0.000000] Switching to high address space at 0x800000000 > [ 0.000000] WARNING: unsafe modification of in-place page tables > - tainting kernel > [ 0.000000] cma: Reserved 16 MiB at 0x000000085f000000 > [ 0.000000] Forcing write-allocate cache policy for SMP > [ 0.000000] Memory policy: Data cache writealloc > [ 0.000000] On node 0 totalpages: 917504 > [ 0.000000] free_area_init_node: node 0, pgdat c078c240, > node_mem_map ed7f9000 > [ 0.000000] DMA zone: 1520 pages used for memmap > [ 0.000000] DMA zone: 0 pages reserved > [ 0.000000] DMA zone: 194560 pages, LIFO batch:31 > [ 0.000000] HighMem zone: 722944 pages, LIFO batch:31 > [ 0.000000] PERCPU: Embedded 10 pages/cpu @ed7b2000 s12096 r8192 > d20672 u40960 > [ 0.000000] pcpu-alloc: s12096 r8192 d20672 u40960 alloc=10*4096 > [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping > on. Total pages: 915984 > [ 0.000000] Kernel command line: console=ttyS0,115200n8 > rootwait=1 clk_ignore_unused debug earlyprintk rdinit=/sbin/init rw > root=/dev/ram0 initrd=0x802000000,9M > [ 0.000000] log_buf_len individual max cpu contribution: 4096 bytes > [ 0.000000] log_buf_len total cpu_extra contributions: 12288 bytes > [ 0.000000] log_buf_len min size: 16384 bytes > [ 0.000000] log_buf_len: 32768 bytes > [ 0.000000] early log buf free: 14536(88%) > [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) > [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, > 524288 bytes) > [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, > 262144 bytes) > [ 0.000000] Memory: 3606688K/3670016K available (5220K kernel > code, 288K rwdata, 1888K rodata, 315K init, 174K bss, 46944K > reserved, 16384K cma-reserved, 2875392K highmem) > [ 0.000000] Virtual kernel memory layout: > [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) > [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) > [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) > [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) > [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) > [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) > [ 0.000000] .text : 0xc0008000 - 0xc06f95bc (7110 kB) > [ 0.000000] .init : 0xc06fa000 - 0xc0748f40 ( 316 kB) > [ 0.000000] .data : 0xc074a000 - 0xc079217c ( 289 kB) > [ 0.000000] .bss : 0xc079217c - 0xc07bdaa0 ( 175 kB) > [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 > [ 0.000000] Preemptible hierarchical RCU implementation. > [ 0.000000] NR_IRQS:16 nr_irqs:16 16 > [ 0.000000] Architected cp15 timer(s) running at 208.33MHz (virt). > [ 0.000003] sched_clock: 56 bits at 208MHz, resolution 4ns, wraps > every 2638828011520ns > [ 0.000011] Switching to timer-based delay loop, resolution 4ns > [ 0.000122] keystone timer clock @208333333 Hz > [ 0.000219] Console: colour dummy device 80x30 > [ 0.000234] Calibrating delay loop (skipped), value calculated > using timer frequency.. 416.66 BogoMIPS (lpj=2083333) > [ 0.000244] pid_max: default: 4096 minimum: 301 > [ 0.000306] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) > [ 0.000314] Mountpoint-cache hash table entries: 2048 (order: 1, > 8192 bytes) > [ 0.000680] CPU: Testing write buffer coherency: ok > [ 0.000824] /cpus/cpu at 0 missing clock-frequency property > [ 0.000838] /cpus/cpu at 1 missing clock-frequency property > [ 0.000851] /cpus/cpu at 2 missing clock-frequency property > [ 0.000865] /cpus/cpu at 3 missing clock-frequency property > [ 0.000874] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 > [ 0.000914] Setting up static identity map for 0x804f3760 - 0x804f3794 > [ 0.139325] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 > [ 0.229428] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 > [ 0.319532] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 > [ 0.319599] Brought up 4 CPUs > [ 0.319613] CPU: All CPU(s) started in SVC mode. > [ 0.320333] VFP support v0.3: implementor 41 architecture 4 part > 30 variant f rev 0 > [ 0.324330] NET: Registered protocol family 16 > [ 0.325137] DMA: preallocated 256 KiB pool for atomic coherent > allocations > [ 0.330901] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 > watchpoint registers. > [ 0.330908] hw-breakpoint: maximum watchpoint size is 8 bytes. > [ 0.339937] vgaarb: loaded > [ 0.340214] SCSI subsystem initialized > [ 0.340617] usbcore: registered new interface driver usbfs > [ 0.340696] usbcore: registered new interface driver hub > [ 0.340790] usbcore: registered new device driver usb > [ 0.342609] Switched to clocksource arch_sys_counter > [ 0.364910] NET: Registered protocol family 2 > [ 0.365338] TCP established hash table entries: 8192 (order: 3, > 32768 bytes) > [ 0.365389] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) > [ 0.365494] TCP: Hash tables configured (established 8192 bind 8192) > [ 0.365531] TCP: reno registered > [ 0.365540] UDP hash table entries: 512 (order: 2, 16384 bytes) > [ 0.365565] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) > [ 0.365699] NET: Registered protocol family 1 > [ 0.365857] RPC: Registered named UNIX socket transport module. > [ 0.365864] RPC: Registered udp transport module. > [ 0.365869] RPC: Registered tcp transport module. > [ 0.365874] RPC: Registered tcp NFSv4.1 backchannel transport module. > [ 0.365889] PCI: CLS 0 bytes, default 64 > [ 0.366023] Unpacking initramfs... > [ 0.797798] Freeing initrd memory: 9216K (c2000000 - c2900000) > [ 0.797991] hw perfevents: enabled with armv7_cortex_a15 PMU > driver, 7 counters available > [ 0.798630] platform alarmtimer: set dma_pfn_offset00780000 > [ 0.799270] futex hash table entries: 16 (order: -2, 1024 bytes) > [ 0.810620] Installing knfsd (copyright (C) 1996 okir at monad.swb.de). > [ 0.810718] ntfs: driver 2.1.31 [Flags: R/O]. > [ 0.811058] jffs2: version 2.2. (NAND) ?? 2001-2006 Red Hat, Inc. > [ 0.812696] NET: Registered protocol family 38 > [ 0.812765] bounce: pool size: 64 pages > [ 0.812992] Block layer SCSI generic (bsg) driver version 0.4 > loaded (major 253) > [ 0.813006] io scheduler noop registered > [ 0.813018] io scheduler deadline registered > [ 0.813197] io scheduler cfq registered (default) > [ 0.813333] keystone_irq soc:keystone_irq at 26202a0: irqchip > registered, nr_irqs 28 > [ 0.813480] gpio-syscon soc:keystone_dsp_gpio at 02620240: can't > read the dir register offset! > [ 0.814272] keystone-pcie 21801000.pcie: missing *config* reg space > [ 1.014637] keystone-pcie 21801000.pcie: phy link never came up > [ 1.014853] keystone-pcie 21801000.pcie: PCI host bridge to bus 0000:00 > [ 1.014865] pci_bus 0000:00: root bus resource [io 0x1000-0x3fff] > [ 1.014874] pci_bus 0000:00: root bus resource [mem > 0x50000000-0x5fffffff] > [ 1.014883] pci_bus 0000:00: root bus resource [bus 00-ff] > [ 1.014913] pci 0000:00:00.0: [104c:b009] type 01 class 0x060400 > [ 1.015180] PCI: bus0: Fast back to back transfers disabled > [ 1.015324] PCI: bus1: Fast back to back transfers enabled > [ 1.015334] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 > [ 1.015389] pci 0000:00:00.0: PCI bridge to [bus 01] > [ 1.015599] pcieport 0000:00:00.0: Signaling PME through PCIe PME > interrupt > [ 1.015610] pcie_pme 0000:00:00.0:pcie01: service driver pcie_pme loaded > [ 1.015736] aer 0000:00:00.0:pcie02: service driver aer loaded > [ 1.016058] keystone-pcie 21021000.pcie: missing *config* reg space > [ 1.016075] Requested IO range too big, new size set to 64K > [ 1.215646] keystone-pcie 21021000.pcie: phy link never came up > [ 1.215857] keystone-pcie 21021000.pcie: PCI host bridge to bus 0001:00 > [ 1.215867] pci_bus 0001:00: root bus resource [io > 0x10000-0xfffff] (bus address [0x0000-0xeffff]) > [ 1.215876] pci_bus 0001:00: root bus resource [mem > 0x60000000-0x6fffffff] > [ 1.215884] pci_bus 0001:00: root bus resource [bus 00-ff] > [ 1.215910] pci 0001:00:00.0: [104c:b009] type 01 class 0x060400 > [ 1.216162] PCI: bus0: Fast back to back transfers disabled > [ 1.216313] PCI: bus1: Fast back to back transfers enabled > [ 1.216322] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 > [ 1.216378] pci 0001:00:00.0: PCI bridge to [bus 01] > [ 1.216578] pcieport 0001:00:00.0: Signaling PME through PCIe PME > interrupt > [ 1.216588] pcie_pme 0001:00:00.0:pcie01: service driver pcie_pme loaded > [ 1.216712] aer 0001:00:00.0:pcie02: service driver aer loaded > [ 1.256740] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled > [ 1.256825] platform serial8250: set dma_pfn_offset00780000 > [ 1.257936] console [ttyS0] disabled > [ 1.257993] of_serial 2530c00.serial: ttyS0 at MMIO 0x2530c00 > (irq = 26, base_baud = 13020833) is a 16550A > [ 2.082903] console [ttyS0] enabled > [ 2.086928] of_serial 2531000.serial: ttyS1 at MMIO 0x2531000 > (irq = 27, base_baud = 13020833) is a 16550A > [ 2.099328] loop: module loaded > [ 2.102592] at24 0-0050: 131072 byte 24c1024 EEPROM, writable, 1 > bytes/write > [ 2.114188] m25p80 spi32766.0: n25q128a11 (16384 Kbytes) > [ 2.119507] 2 ofpart partitions found on MTD device spi32766.0 > [ 2.125340] Creating 2 MTD partitions on "spi32766.0": > [ 2.130472] 0x000000000000-0x000000080000 : "u-boot-spl" > [ 2.136411] 0x000000080000-0x000001000000 : "misc" > [ 2.141765] spi_davinci 21000400.spi: Controller at 0xf014a400 > [ 2.147931] spi_davinci 21000600.spi: Controller at 0xf014c600 > [ 2.154096] spi_davinci 21000800.spi: Controller at 0xf014e800 > [ 2.360911] dwc3 2690000.dwc3: No power optimization available > [ 2.366743] dwc3 2690000.dwc3: found 16 IN and 16 OUT endpoints > [ 2.572689] dwc3 2690000.dwc3: Event buf ec9c1000 dma ac9c1000 length 256 > [ 2.579469] dwc3 2690000.dwc3: Event buf ec9c2000 dma ac9c2000 length 256 > [ 2.586254] dwc3 2690000.dwc3: Event buf ec9c3000 dma ac9c3000 length 256 > [ 2.593039] dwc3 2690000.dwc3: Event buf ed164000 dma ad164000 length 256 > [ 2.599819] dwc3 2690000.dwc3: Event buf ed166000 dma ad166000 length 256 > [ 2.606603] dwc3 2690000.dwc3: Event buf ed167000 dma ad167000 length 256 > [ 2.613387] dwc3 2690000.dwc3: Event buf ec82c000 dma ac82c000 length 256 > [ 2.620166] dwc3 2690000.dwc3: Event buf ec82d000 dma ac82d000 length 256 > [ 2.626951] dwc3 2690000.dwc3: Event buf ec82e000 dma ac82e000 length 256 > [ 2.633735] dwc3 2690000.dwc3: Event buf ec82f000 dma ac82f000 length 256 > [ 2.640514] dwc3 2690000.dwc3: Event buf ecb80000 dma acb80000 length 256 > [ 2.647298] dwc3 2690000.dwc3: Event buf ecb81000 dma acb81000 length 256 > [ 2.654083] dwc3 2690000.dwc3: Event buf ecb82000 dma acb82000 length 256 > [ 2.660862] dwc3 2690000.dwc3: Event buf ecb83000 dma acb83000 length 256 > [ 2.667647] dwc3 2690000.dwc3: Event buf ed34c000 dma ad34c000 length 256 > [ 2.674430] dwc3 2690000.dwc3: Event buf ed34d000 dma ad34d000 length 256 > [ 2.681274] platform xhci-hcd.0.auto: set dma_pfn_offset00780000 > [ 2.887719] dwc3 25010000.dwc3: No power optimization available > [ 2.893637] dwc3 25010000.dwc3: found 16 IN and 16 OUT endpoints > [ 3.099664] dwc3 25010000.dwc3: Event buf ecbd0000 dma acbd0000 > length 256 > [ 3.106537] dwc3 25010000.dwc3: Event buf ecbd1000 dma acbd1000 > length 256 > [ 3.113410] dwc3 25010000.dwc3: Event buf ecbd2000 dma acbd2000 > length 256 > [ 3.120276] dwc3 25010000.dwc3: Event buf ecbd3000 dma acbd3000 > length 256 > [ 3.127148] dwc3 25010000.dwc3: Event buf ec866000 dma ac866000 > length 256 > [ 3.134019] dwc3 25010000.dwc3: Event buf ec867000 dma ac867000 > length 256 > [ 3.140885] dwc3 25010000.dwc3: Event buf ecb74000 dma acb74000 > length 256 > [ 3.147756] dwc3 25010000.dwc3: Event buf ecb75000 dma acb75000 > length 256 > [ 3.154628] dwc3 25010000.dwc3: Event buf ed3d2000 dma ad3d2000 > length 256 > [ 3.161495] dwc3 25010000.dwc3: Event buf ed3d3000 dma ad3d3000 > length 256 > [ 3.168367] dwc3 25010000.dwc3: Event buf ec828000 dma ac828000 > length 256 > [ 3.175239] dwc3 25010000.dwc3: Event buf ec829000 dma ac829000 > length 256 > [ 3.182105] dwc3 25010000.dwc3: Event buf ed1da000 dma ad1da000 > length 256 > [ 3.188975] dwc3 25010000.dwc3: Event buf ed1db000 dma ad1db000 > length 256 > [ 3.195846] dwc3 25010000.dwc3: Event buf ed160000 dma ad160000 > length 256 > [ 3.202716] dwc3 25010000.dwc3: Event buf ed161000 dma ad161000 > length 256 > [ 3.209649] platform xhci-hcd.1.auto: set dma_pfn_offset00780000 > [ 3.215984] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > [ 3.221567] xhci-hcd xhci-hcd.0.auto: new USB bus registered, > assigned bus number 1 > [ 3.229502] xhci-hcd xhci-hcd.0.auto: irq 34, io mem 0x02690000 > [ 3.235545] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 > [ 3.242326] usb usb1: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 3.249552] usb usb1: Product: xHCI Host Controller > [ 3.254430] usb usb1: Manufacturer: Linux > 3.18.0-11757-gd790be3-dirty xhci-hcd > [ 3.261643] usb usb1: SerialNumber: xhci-hcd.0.auto > [ 3.266901] hub 1-0:1.0: USB hub found > [ 3.270666] hub 1-0:1.0: 1 port detected > [ 3.274845] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > [ 3.280445] xhci-hcd xhci-hcd.0.auto: new USB bus registered, > assigned bus number 2 > [ 3.288235] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 > [ 3.295027] usb usb2: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 3.302240] usb usb2: Product: xHCI Host Controller > [ 3.307118] usb usb2: Manufacturer: Linux > 3.18.0-11757-gd790be3-dirty xhci-hcd > [ 3.314340] usb usb2: SerialNumber: xhci-hcd.0.auto > [ 3.319582] hub 2-0:1.0: USB hub found > [ 3.323353] hub 2-0:1.0: 1 port detected > [ 3.327559] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > [ 3.333182] xhci-hcd xhci-hcd.1.auto: new USB bus registered, > assigned bus number 3 > [ 3.341014] xhci-hcd xhci-hcd.1.auto: irq 68, io mem 0x25010000 > [ 3.347041] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 > [ 3.353832] usb usb3: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 3.361045] usb usb3: Product: xHCI Host Controller > [ 3.365923] usb usb3: Manufacturer: Linux > 3.18.0-11757-gd790be3-dirty xhci-hcd > [ 3.373836] usb usb3: SerialNumber: xhci-hcd.1.auto > [ 3.379079] hub 3-0:1.0: USB hub found > [ 3.382850] hub 3-0:1.0: 1 port detected > [ 3.387013] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > [ 3.392622] xhci-hcd xhci-hcd.1.auto: new USB bus registered, > assigned bus number 4 > [ 3.400399] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 > [ 3.407189] usb usb4: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 3.414412] usb usb4: Product: xHCI Host Controller > [ 3.419282] usb usb4: Manufacturer: Linux > 3.18.0-11757-gd790be3-dirty xhci-hcd > [ 3.427836] usb usb4: SerialNumber: xhci-hcd.1.auto > [ 3.433091] hub 4-0:1.0: USB hub found > [ 3.436850] hub 4-0:1.0: 1 port detected > [ 3.441197] usbcore: registered new interface driver usb-storage > [ 3.447572] mousedev: PS/2 mouse device common for all mice > [ 3.453353] i2c /dev entries driver > [ 3.457258] davinci-wdt 22f0080.wdt: heartbeat 60 sec > [ 3.462762] usbcore: registered new interface driver usbhid > [ 3.468325] usbhid: USB HID core driver > [ 3.472893] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xac > [ 3.479237] nand: Micron MT29F4G08ABBDAHC > [ 3.483945] nand: 512 MiB, SLC, erase size: 128 KiB, page size: > 2048, OOB size: 64 > [ 3.491793] Bad block table found at page 262080, version 0x01 > [ 3.498135] Bad block table found at page 262016, version 0x01 > [ 3.504281] 3 ofpart partitions found on MTD device 30000000.nand > [ 3.510365] Creating 3 MTD partitions on "30000000.nand": > [ 3.515765] 0x000000000000-0x000000100000 : "u-boot" > [ 3.521319] 0x000000100000-0x000000180000 : "params" > [ 3.526843] 0x000000180000-0x000020000000 : "ubifs" > [ 3.532529] davinci_nand 30000000.nand: controller rev. 2.5 > [ 3.539597] platform oprofile-perf.0: set dma_pfn_offset00780000 > [ 3.545733] oprofile: using timer interrupt. > [ 3.550019] Netfilter messages via NETLINK v0.30. > [ 3.554737] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) > [ 3.561219] ctnetlink v0.93: registering with nfnetlink. > [ 3.566790] ipip: IPv4 over IPv4 tunneling driver > [ 3.571876] gre: GRE over IPv4 demultiplexor driver > [ 3.576762] ip_gre: GRE over IPv4 tunneling driver > [ 3.582421] ip_tables: (C) 2000-2006 Netfilter Core Team > [ 3.587816] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully > [ 3.594195] arp_tables: (C) 2002 David S. Miller > [ 3.598847] TCP: cubic registered > [ 3.602157] Initializing XFRM netlink socket > [ 3.606965] NET: Registered protocol family 10 > [ 3.612005] NET: Registered protocol family 17 > [ 3.616472] NET: Registered protocol family 15 > [ 3.620912] 8021q: 802.1Q VLAN Support v1.8 > [ 3.626750] sctp: Hash tables configured (established 65536 bind 65536) > [ 3.633786] Registering SWP/SWPB emulation handler > [ 3.641684] clk: Not disabling unused clocks > [ 3.646516] Freeing unused kernel memory: 312K (c06fa000 - c0748000) > INIT: version 2.88 booting > Starting udev > Starting Bootlog daemon: bootlogd. > Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device > ifconfig: SIOCGIFFLAGS: No such device > done. > Mon Jul 8 13:27:00 UTC 2013 > Configuring update-modules. > ERROR: could not open directory > /lib/modules/3.18.0-11757-gd790be3-dirty: No such file or directory > WARNING: -e needs -E or -F > ERROR: could not open directory > /lib/modules/3.18.0-11757-gd790be3-dirty: No such file or directory > INIT: Entering runlevel: 5dules: No such file or direct > Starting telnet daemon. > Starting syslogd/klogd: done > Starting thttpd. > Stopping Bootlog daemon: bootlogd. > > _____ _____ _ _ > | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ > | | _| .'| . | . | | __| _| . | | | -_| _| _| > |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| > |___| |___| > > Arago Project http://arago-project.org keystone-evm ttyS0 > > Arago 2013.04 keystone-evm ttyS0 > > keystone-evm login: root > root at keystone-evm:~# uname -a > Linux keystone-evm 3.18.0-11757-gd790be3-dirty #16 SMP PREEMPT Fri > Dec 19 18:14:46 EST 2014 armv7l GNU/Linux > root at keystone-evm:~# > > > > > -- > Murali Karicheri > Linux Kernel, Texas Instruments > -- Pengutronix e.K. | Uwe Kleine-K?nig | Industrial Linux Solutions | http://www.pengutronix.de/ |