[PATCH 2/2] ARM: Kirkwood: add DT support for Seagate Goflex Home and CloudEngines Pogoplug E02

[PATCH 2/2] ARM: Kirkwood: add DT support for Seagate Goflex Home and CloudEngines Pogoplug E02

[Andrew Lunn]

On Sun, Aug 10, 2014 at 04:37:37AM -0600, Oleg Rakhmanov wrote:
> This patch adds Pogoplug E02 support and to apply clean it depends on the
> first patch in the series.

Hi Oleg

I don't see any dependencies between the two patches.  Even if there
is, we treat a two patch series as one entity, and apply them together
in order. So you can remove that part of the comment.

> 
> diff -uprN a/arch/arm/boot/dts/kirkwood-pogo_e02.dts
> b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
> --- a/arch/arm/boot/dts/kirkwood-pogo_e02.dts   1969-12-31
> 17:00:00.000000000 -0700
> +++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts   2014-08-10
> 03:59:10.616338535 -0600
> @@ -0,0 +1,117 @@
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +
> +/ {
> +       model = "CloudEngines Pogoplug E02";
> +       compatible = "cloudengines,pogo_e02", "marvell,kirkwood-88f6281",
> "marvell,kirkwood";

All vendors should be listed in
Documentation/devicetree/bindings/vendor-prefixes.txt.  Please could
you make a separate patch in this series adding it.

> +       memory {
> +               device_type = "memory";
> +               reg = <0x00000000 0x10000000>;
> +       };
> +
> +       chosen {
> +               bootargs = "console=ttyS0,115200n8 earlyprintk
> root=/dev/sda1 rootdelay=10";
> +               stdout-path = &uart0;
> +       };
> +
> +       ocp at f1000000 {
> +               pinctrl: pin-controller at 10000 {
> +                       pmx_usb_power_enable: pmx-usb-power-enable {
> +                               marvell,pins = "mpp29";
> +                               marvell,function = "gpio";
> +                       };
> +                       pmx_led_green: pmx-led_green {

Last _ should be -

> +                               marvell,pins = "mpp48";
> +                               marvell,function = "gpio";
> +                       };
> +                       pmx_led_orange: pmx-led_orange {

Same here.

> +                               marvell,pins = "mpp49";
> +                               marvell,function = "gpio";
> +                       };
> +               };
> +               serial at 12000 {
> +                       status = "ok";
> +               };
> +
> +       };
> +       gpio-leds {
> +               compatible = "gpio-leds";
> +               pinctrl-0 = < &pmx_led_orange
> +                             &pmx_led_green
> +                           >;
> +               pinctrl-names = "default";
> +
> +               health {
> +                       label = "status:green:health";
> +                       gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
> +                       default-state = "keep";
> +               };
> +               fault {
> +                       label = "status:orange:fault";
> +                       gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
> +               };
> +       };
> +       regulators {
> +               compatible = "simple-bus";
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +               pinctrl-0 = <&pmx_usb_power_enable>;
> +               pinctrl-names = "default";
> +
> +               usb_power: regulator at 1 {
> +                       compatible = "regulator-fixed";
> +                       reg = <1>;
> +                       regulator-name = "USB Power";
> +                       regulator-min-microvolt = <5000000>;
> +                       regulator-max-microvolt = <5000000>;
> +                       enable-active-high;
> +                       regulator-always-on;
> +                       regulator-boot-on;
> +                       gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
> +               };
> +       };
> +};
> +
> +&nand {
> +       chip-delay = <25>;
> +       status = "okay";
> +
> +       partition at 0 {
> +               label = "u-boot";
> +               reg = <0x0000000 0x100000>;
> +               read-only;
> +       };
> +
> +       partition at 100000 {
> +               label = "uImage";
> +               reg = <0x0100000 0x0500000>;
> +       };
> +
> +        partition at 0500000 {
> +                label = "pogoplug";
> +                reg = <0x0500000 0x2500000>;
> +        };
> +
> +       partition at 2500000 {
> +               label = "root";
> +               reg = <0x2500000 0x6c00000>;
> +       };
> +};
> +
> +&mdio {
> +       status = "okay";
> +
> +       ethphy0: ethernet-phy at 0 {
> +               reg = <0>;
> +       };
> +};
> +
> +&eth0 {
> +       status = "okay";
> +       ethernet0-port at 0 {
> +               phy-handle = <&ethphy0>;
> +       };
> +};
> diff -uprN a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> --- a/arch/arm/boot/dts/Makefile        2014-08-10 03:54:22.764885366 -0600
> +++ b/arch/arm/boot/dts/Makefile        2014-08-10 04:00:43.570037020 -0600
> @@ -137,6 +137,7 @@ kirkwood := \
>         kirkwood-openrd-base.dtb \
>         kirkwood-openrd-client.dtb \
>         kirkwood-openrd-ultimate.dtb \
> +      kirkwood-pogo_e02.dtb \

Again, there looks to be something odd here.

>         kirkwood-rd88f6192.dtb \
>         kirkwood-rd88f6281-a0.dtb \
>         kirkwood-rd88f6281-a1.dtb \

Thanks
	Andrew

[PATCH] Added support for pogoplug e02 (pink/gray)

[Christoph Junghans]

The pogoplug differs from the SheevaPlug only by a
few details, but especially in the led assignments.
This patch was tested under Gentoo Linux.
A version of this patch was included in Arch Linux
on Arm since Jun 2014:
https://github.com/archlinuxarm/PKGBUILDs/commit/250c2f0aa6ffe66c0ebda61efaa356e5dc709cc7
A similar patch is available for OpenWrt:
https://dev.openwrt.org/browser/trunk/target/linux/kirkwood/patches-3.14/150-pogoplug_e02.patch

Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
---
 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/kirkwood-pogo_e02.dts            | 114 +++++++++++++++++++++
 3 files changed, 116 insertions(+)
 create mode 100644 arch/arm/boot/dts/kirkwood-pogo_e02.dts

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index ac7269f..e5f58c6 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -32,6 +32,7 @@ cdns	Cadence Design Systems Inc.
 chrp	Common Hardware Reference Platform
 chunghwa	Chunghwa Picture Tubes Ltd.
 cirrus	Cirrus Logic, Inc.
+cloudengines	Cloud Engines, Inc.
 cortina	Cortina Systems, Inc.
 crystalfontz	Crystalfontz America, Inc.
 dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b8c5cd3..cd974eb 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -143,6 +143,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \
 	kirkwood-openrd-base.dtb \
 	kirkwood-openrd-client.dtb \
 	kirkwood-openrd-ultimate.dtb \
+	kirkwood-pogo_e02.dtb \
 	kirkwood-rd88f6192.dtb \
 	kirkwood-rd88f6281-a0.dtb \
 	kirkwood-rd88f6281-a1.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-pogo_e02.dts b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
new file mode 100644
index 0000000..286a6be
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
@@ -0,0 +1,114 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Cloud Engines Pogoplug E02";
+	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+	};
+
+	ocp at f1000000 {
+		pinctrl: pinctrl at 10000 {
+			pmx_usb_power_enable: pmx-usb-power-enable {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+			pmx_led_green: pmx-led-green {
+				marvell,pins = "mpp48";
+				marvell,function = "gpio";
+			};
+			pmx_led_orange: pmx-led-orange {
+				marvell,pins = "mpp49";
+				marvell,function = "gpio";
+			};
+		};
+		serial at 12000 {
+			status = "ok";
+		};
+	};
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
+			      &pmx_led_green >;
+		pinctrl-names = "default";
+
+		health {
+			label = "status:green:health";
+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+		fault {
+			label = "status:orange:fault";
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&nand {
+	chip-delay = <40>;
+	status = "okay";
+
+	partition at 0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	partition at 100000 {
+		label = "uImage";
+		reg = <0x0100000 0x400000>;
+	};
+
+	partition at 500000 {
+		label = "pogoplug";
+		reg = <0x0500000 0x2000000>;
+	};
+
+	partition at 2500000 {
+		label = "root";
+		reg = <0x02500000 0x5b00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};
-- 
2.0.5

[PATCH] Added support for pogoplug e02 (pink/gray)

[Arnd Bergmann]

On Sunday 11 January 2015 23:11:01 Christoph Junghans wrote:
> The pogoplug differs from the SheevaPlug only by a
> few details, but especially in the led assignments.
> This patch was tested under Gentoo Linux.
> A version of this patch was included in Arch Linux
> on Arm since Jun 2014:
> https://github.com/archlinuxarm/PKGBUILDs/commit/250c2f0aa6ffe66c0ebda61efaa356e5dc709cc7
> A similar patch is available for OpenWrt:
> https://dev.openwrt.org/browser/trunk/target/linux/kirkwood/patches-3.14/150-pogoplug_e02.patch
> 
> Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
> Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
> Signed-off-by: Christoph Junghans <ottxor@gentoo.org>

Very nice, glad someone found the time to do this. Maybe
I should buy one now ;-)

> +
> +	chosen {
> +		bootargs = "console=ttyS0,115200n8 earlyprintk";
> +	};

I'd like to move away from using 'earlyprintk' in dts files.
Can you remove this here and add a 'stdout-path' property that
can be used with 'earlycon'? Unfortunately 3.19 doesn't support
earlycon on ARM yet, but I hope to see that working in 3.20
at last.

	Arnd

[PATCH] Added support for pogoplug e02 (pink/gray)

[Andrew Lunn]

On Sun, Jan 11, 2015 at 11:11:01PM -0700, Christoph Junghans wrote:
> The pogoplug differs from the SheevaPlug only by a
> few details, but especially in the led assignments.
> This patch was tested under Gentoo Linux.
> A version of this patch was included in Arch Linux
> on Arm since Jun 2014:
> https://github.com/archlinuxarm/PKGBUILDs/commit/250c2f0aa6ffe66c0ebda61efaa356e5dc709cc7
> A similar patch is available for OpenWrt:
> https://dev.openwrt.org/browser/trunk/target/linux/kirkwood/patches-3.14/150-pogoplug_e02.patch
> 
> Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
> Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
> Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
> ---
>  .../devicetree/bindings/vendor-prefixes.txt        |   1 +
>  arch/arm/boot/dts/Makefile                         |   1 +
>  arch/arm/boot/dts/kirkwood-pogo_e02.dts            | 114 +++++++++++++++++++++
>  3 files changed, 116 insertions(+)
>  create mode 100644 arch/arm/boot/dts/kirkwood-pogo_e02.dts
> 
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index ac7269f..e5f58c6 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -32,6 +32,7 @@ cdns	Cadence Design Systems Inc.
>  chrp	Common Hardware Reference Platform
>  chunghwa	Chunghwa Picture Tubes Ltd.
>  cirrus	Cirrus Logic, Inc.
> +cloudengines	Cloud Engines, Inc.
>  cortina	Cortina Systems, Inc.
>  crystalfontz	Crystalfontz America, Inc.
>  dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b8c5cd3..cd974eb 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -143,6 +143,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \
>  	kirkwood-openrd-base.dtb \
>  	kirkwood-openrd-client.dtb \
>  	kirkwood-openrd-ultimate.dtb \
> +	kirkwood-pogo_e02.dtb \
>  	kirkwood-rd88f6192.dtb \
>  	kirkwood-rd88f6281-a0.dtb \
>  	kirkwood-rd88f6281-a1.dtb \
> diff --git a/arch/arm/boot/dts/kirkwood-pogo_e02.dts b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
> new file mode 100644
> index 0000000..286a6be
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
> @@ -0,0 +1,114 @@

Hi Christoph

Do you have any idea of the license on this file? Since there is
nothing stated, i assume it falls under the general Linux kernel
licence, GPL v2. Please could you add a normal GPLv2 header.

> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +
> +/ {
> +	model = "Cloud Engines Pogoplug E02";
> +	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281", "marvell,kirkwood";
> +
> +	memory {
> +		device_type = "memory";
> +		reg = <0x00000000 0x10000000>;
> +	};
> +
> +	chosen {
> +		bootargs = "console=ttyS0,115200n8 earlyprintk";
> +	};
> +
> +	ocp at f1000000 {
> +		pinctrl: pinctrl at 10000 {
> +			pmx_usb_power_enable: pmx-usb-power-enable {
> +				marvell,pins = "mpp29";
> +				marvell,function = "gpio";
> +			};
> +			pmx_led_green: pmx-led-green {
> +				marvell,pins = "mpp48";
> +				marvell,function = "gpio";
> +			};
> +			pmx_led_orange: pmx-led-orange {
> +				marvell,pins = "mpp49";
> +				marvell,function = "gpio";
> +			};
> +		};
> +		serial at 12000 {
> +			status = "ok";
> +		};
> +	};
> +	gpio-leds {
> +		compatible = "gpio-leds";
> +		pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
> +			      &pmx_led_green >;
> +		pinctrl-names = "default";
> +
> +		health {
> +			label = "status:green:health";
> +			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
> +			default-state = "keep";
> +		};
> +		fault {
> +			label = "status:orange:fault";
> +			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
> +		};
> +	};

Documentation/leds/leds-class.txt says:

LED Device Naming
=================

Is currently of the form:

"devicename:colour:function"

Please could you change status to pogo_e02.

The rest looks good, and thanks for remembering the vendor.txt file.

    Andrew

> +	regulators {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		pinctrl-0 = <&pmx_usb_power_enable>;
> +		pinctrl-names = "default";
> +
> +		usb_power: regulator at 1 {
> +			compatible = "regulator-fixed";
> +			reg = <1>;
> +			regulator-name = "USB Power";
> +			regulator-min-microvolt = <5000000>;
> +			regulator-max-microvolt = <5000000>;
> +			enable-active-high;
> +			regulator-always-on;
> +			regulator-boot-on;
> +			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
> +		};
> +	};
> +};
> +
> +&nand {
> +	chip-delay = <40>;
> +	status = "okay";
> +
> +	partition at 0 {
> +		label = "u-boot";
> +		reg = <0x0000000 0x100000>;
> +		read-only;
> +	};
> +
> +	partition at 100000 {
> +		label = "uImage";
> +		reg = <0x0100000 0x400000>;
> +	};
> +
> +	partition at 500000 {
> +		label = "pogoplug";
> +		reg = <0x0500000 0x2000000>;
> +	};
> +
> +	partition at 2500000 {
> +		label = "root";
> +		reg = <0x02500000 0x5b00000>;
> +	};
> +};
> +
> +&mdio {
> +	status = "okay";
> +
> +	ethphy0: ethernet-phy at 0 {
> +		reg = <0>;
> +	};
> +};
> +
> +&eth0 {
> +	status = "okay";
> +	ethernet0-port at 0 {
> +		phy-handle = <&ethphy0>;
> +	};
> +};
> -- 
> 2.0.5
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH] Added support for pogoplug e02 (pink/gray)

[Russell King - ARM Linux]

On Mon, Jan 12, 2015 at 01:59:21PM +0100, Andrew Lunn wrote:
> Do you have any idea of the license on this file? Since there is
> nothing stated, i assume it falls under the general Linux kernel
> licence, GPL v2. Please could you add a normal GPLv2 header.

Note that it shouldn't include the FSF mailing address, which has
changed several times already.  The first two paragraphs of text
are fine (suitably modified to specify GPLv2 or GPLv2+).

-- 
FTTC broadband for 0.8mile line: currently at 10.5Mbps down 400kbps up
according to speedtest.net.

[PATCH] Added support for pogoplug e02 (pink/gray)

[Andrew Lunn]

On Sun, Jan 11, 2015 at 11:11:01PM -0700, Christoph Junghans wrote:
> The pogoplug differs from the SheevaPlug only by a
> few details, but especially in the led assignments.
> This patch was tested under Gentoo Linux.
> A version of this patch was included in Arch Linux
> on Arm since Jun 2014:
> https://github.com/archlinuxarm/PKGBUILDs/commit/250c2f0aa6ffe66c0ebda61efaa356e5dc709cc7
> A similar patch is available for OpenWrt:
> https://dev.openwrt.org/browser/trunk/target/linux/kirkwood/patches-3.14/150-pogoplug_e02.patch
> 
> Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
> Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
> Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
> ---
>  .../devicetree/bindings/vendor-prefixes.txt        |   1 +
>  arch/arm/boot/dts/Makefile                         |   1 +
>  arch/arm/boot/dts/kirkwood-pogo_e02.dts            | 114 +++++++++++++++++++++
>  3 files changed, 116 insertions(+)
>  create mode 100644 arch/arm/boot/dts/kirkwood-pogo_e02.dts
> 
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index ac7269f..e5f58c6 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -32,6 +32,7 @@ cdns	Cadence Design Systems Inc.
>  chrp	Common Hardware Reference Platform
>  chunghwa	Chunghwa Picture Tubes Ltd.
>  cirrus	Cirrus Logic, Inc.
> +cloudengines	Cloud Engines, Inc.
>  cortina	Cortina Systems, Inc.
>  crystalfontz	Crystalfontz America, Inc.
>  dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile

Hi Christoph

Please make sure the device tree maintainers see this part of the
patch. I added them as Cc:

We can however take this change via mvebu->arm-soc if nobody objects.

   Andrew

[PATCH v2] Added support for pogoplug e02 (pink/gray)

[Christoph Junghans]

The pogoplug differs from the SheevaPlug only by a
few details, but especially in the led assignments.
This patch was tested under Gentoo Linux and is
based on dts files from Arch Linux ARM and OpenWrt.

Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
---
 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/kirkwood-pogo_e02.dts            | 129 +++++++++++++++++++++
 3 files changed, 131 insertions(+)
 create mode 100644 arch/arm/boot/dts/kirkwood-pogo_e02.dts

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index ac7269f..e5f58c6 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -32,6 +32,7 @@ cdns	Cadence Design Systems Inc.
 chrp	Common Hardware Reference Platform
 chunghwa	Chunghwa Picture Tubes Ltd.
 cirrus	Cirrus Logic, Inc.
+cloudengines	Cloud Engines, Inc.
 cortina	Cortina Systems, Inc.
 crystalfontz	Crystalfontz America, Inc.
 dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b8c5cd3..cd974eb 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -143,6 +143,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \
 	kirkwood-openrd-base.dtb \
 	kirkwood-openrd-client.dtb \
 	kirkwood-openrd-ultimate.dtb \
+	kirkwood-pogo_e02.dtb \
 	kirkwood-rd88f6192.dtb \
 	kirkwood-rd88f6281-a0.dtb \
 	kirkwood-rd88f6281-a1.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-pogo_e02.dts b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
new file mode 100644
index 0000000..be38dab
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
@@ -0,0 +1,129 @@
+/*
+ * kirkwood-sheevaplug.dts - Device tree file for Pogoplug E02
+ *
+ * Copyright (C) 2015 Christoph Junghans <ottxor@gentoo.org>
+ *
+ * based on information of dts files from
+ *  Arch Linux ARM by Oleg Rakhmanov <moonman.ca@gmail.com>
+ *  OpenWrt by Felix Kaechele <heffer@fedoraproject.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Cloud Engines Pogoplug E02";
+	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		linux,stdout-path = &serial1;
+	};
+
+	ocp at f1000000 {
+		pinctrl: pinctrl at 10000 {
+			pmx_usb_power_enable: pmx-usb-power-enable {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+			pmx_led_green: pmx-led-green {
+				marvell,pins = "mpp48";
+				marvell,function = "gpio";
+			};
+			pmx_led_orange: pmx-led-orange {
+				marvell,pins = "mpp49";
+				marvell,function = "gpio";
+			};
+		};
+		serial1: serial at 12000 {
+			status = "ok";
+		};
+	};
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
+			      &pmx_led_green >;
+		pinctrl-names = "default";
+
+		health {
+			label = "pogo_e02:green:health";
+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+		fault {
+			label = "pogo_e02:orange:fault";
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&nand {
+	chip-delay = <40>;
+	status = "okay";
+
+	partition at 0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	partition at 100000 {
+		label = "uImage";
+		reg = <0x0100000 0x400000>;
+	};
+
+	partition at 500000 {
+		label = "pogoplug";
+		reg = <0x0500000 0x2000000>;
+	};
+
+	partition at 2500000 {
+		label = "root";
+		reg = <0x02500000 0x5b00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};
-- 
2.0.5

[PATCH v2] Added support for pogoplug e02 (pink/gray)

[Andrew Lunn]

On Mon, Jan 12, 2015 at 06:22:12PM -0700, Christoph Junghans wrote:
> The pogoplug differs from the SheevaPlug only by a
> few details, but especially in the led assignments.
> This patch was tested under Gentoo Linux and is
> based on dts files from Arch Linux ARM and OpenWrt.

Hi Christoph

I just tried compiling this with 3.19-rc1:

  DTC     arch/arm/boot/dts/kirkwood-pogo_e02.dtb
ERROR (duplicate_label): Duplicate label 'pinctrl' on /ocp at f1000000/pinctrl at 10000 and /ocp at f1000000/pin-controller at 10000
ERROR: Input tree has errors, aborting (use -f to force output)

> Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
> Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
> Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
> ---

It is normal to say here, after the --- what you have changed since
the previous version.

>  .../devicetree/bindings/vendor-prefixes.txt        |   1 +
>  arch/arm/boot/dts/Makefile                         |   1 +
>  arch/arm/boot/dts/kirkwood-pogo_e02.dts            | 129 +++++++++++++++++++++
>  3 files changed, 131 insertions(+)
>  create mode 100644 arch/arm/boot/dts/kirkwood-pogo_e02.dts
> 
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index ac7269f..e5f58c6 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -32,6 +32,7 @@ cdns	Cadence Design Systems Inc.
>  chrp	Common Hardware Reference Platform
>  chunghwa	Chunghwa Picture Tubes Ltd.
>  cirrus	Cirrus Logic, Inc.
> +cloudengines	Cloud Engines, Inc.
>  cortina	Cortina Systems, Inc.

This failed to apply. cnm was added Wed May 14 2014, so i guess you are not using 3.19-rc1?

>  crystalfontz	Crystalfontz America, Inc.
>  dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b8c5cd3..cd974eb 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -143,6 +143,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \
>  	kirkwood-openrd-base.dtb \
>  	kirkwood-openrd-client.dtb \
>  	kirkwood-openrd-ultimate.dtb \
> +	kirkwood-pogo_e02.dtb \
>  	kirkwood-rd88f6192.dtb \
>  	kirkwood-rd88f6281-a0.dtb \
>  	kirkwood-rd88f6281-a1.dtb \
> diff --git a/arch/arm/boot/dts/kirkwood-pogo_e02.dts b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
> new file mode 100644
> index 0000000..be38dab
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
> @@ -0,0 +1,129 @@
> +/*
> + * kirkwood-sheevaplug.dts - Device tree file for Pogoplug E02
> + *
> + * Copyright (C) 2015 Christoph Junghans <ottxor@gentoo.org>
> + *
> + * based on information of dts files from
> + *  Arch Linux ARM by Oleg Rakhmanov <moonman.ca@gmail.com>
> + *  OpenWrt by Felix Kaechele <heffer@fedoraproject.org>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2.  This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +
> +/ {
> +	model = "Cloud Engines Pogoplug E02";
> +	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281", "marvell,kirkwood";
> +
> +	memory {
> +		device_type = "memory";
> +		reg = <0x00000000 0x10000000>;
> +	};
> +
> +	chosen {
> +		bootargs = "console=ttyS0,115200n8";
> +		linux,stdout-path = &serial1;

This is not what i was expecting. I would expect it to be

                stdout-path = &uart0;


> +	};
> +
> +	ocp at f1000000 {
> +		pinctrl: pinctrl at 10000 {
> +			pmx_usb_power_enable: pmx-usb-power-enable {
> +				marvell,pins = "mpp29";
> +				marvell,function = "gpio";
> +			};
> +			pmx_led_green: pmx-led-green {
> +				marvell,pins = "mpp48";
> +				marvell,function = "gpio";
> +			};
> +			pmx_led_orange: pmx-led-orange {
> +				marvell,pins = "mpp49";
> +				marvell,function = "gpio";
> +			};
> +		};

To fix the error above, i suggest you take a look at:

https://lkml.org/lkml/2014/12/28/34

	Andrew

> +		serial1: serial at 12000 {
> +			status = "ok";
> +		};
> +	};
> +	gpio-leds {
> +		compatible = "gpio-leds";
> +		pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
> +			      &pmx_led_green >;
> +		pinctrl-names = "default";
> +
> +		health {
> +			label = "pogo_e02:green:health";
> +			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
> +			default-state = "keep";
> +		};
> +		fault {
> +			label = "pogo_e02:orange:fault";
> +			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +	regulators {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		pinctrl-0 = <&pmx_usb_power_enable>;
> +		pinctrl-names = "default";
> +
> +		usb_power: regulator at 1 {
> +			compatible = "regulator-fixed";
> +			reg = <1>;
> +			regulator-name = "USB Power";
> +			regulator-min-microvolt = <5000000>;
> +			regulator-max-microvolt = <5000000>;
> +			enable-active-high;
> +			regulator-always-on;
> +			regulator-boot-on;
> +			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
> +		};
> +	};
> +};
> +
> +&nand {
> +	chip-delay = <40>;
> +	status = "okay";
> +
> +	partition at 0 {
> +		label = "u-boot";
> +		reg = <0x0000000 0x100000>;
> +		read-only;
> +	};
> +
> +	partition at 100000 {
> +		label = "uImage";
> +		reg = <0x0100000 0x400000>;
> +	};
> +
> +	partition at 500000 {
> +		label = "pogoplug";
> +		reg = <0x0500000 0x2000000>;
> +	};
> +
> +	partition at 2500000 {
> +		label = "root";
> +		reg = <0x02500000 0x5b00000>;
> +	};
> +};
> +
> +&mdio {
> +	status = "okay";
> +
> +	ethphy0: ethernet-phy at 0 {
> +		reg = <0>;
> +	};
> +};
> +
> +&eth0 {
> +	status = "okay";
> +	ethernet0-port at 0 {
> +		phy-handle = <&ethphy0>;
> +	};
> +};
> -- 
> 2.0.5
> 

[PATCH v3] Added support for pogoplug e02 (pink/gray)

[Christoph Junghans]

From: Christoph Junghans <ottxor@gentoo.org>

The pogoplug differs from the SheevaPlug only by a
few details, but especially in the led assignments.
This patch was tested under Gentoo Linux and is
based on dts files from Arch Linux ARM and OpenWrt.

Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
---

V1: initial patch
V2: added GPL-2 header
    dropped earlyprintk from bootargs
    added stdout-path
    change leds name to scheme "devicename:colour:function"
V3: rebase on v3.19-rc4
    fixed stdout-path to be &uart0
    fixed compiling issue by using pin-controller

 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/kirkwood-pogo_e02.dts            | 129 +++++++++++++++++++++
 3 files changed, 131 insertions(+)
 create mode 100644 arch/arm/boot/dts/kirkwood-pogo_e02.dts

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index b1df0ad..61888db 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -34,6 +34,7 @@ chipidea	Chipidea, Inc
 chrp	Common Hardware Reference Platform
 chunghwa	Chunghwa Picture Tubes Ltd.
 cirrus	Cirrus Logic, Inc.
+cloudengines	Cloud Engines, Inc.
 cnm	Chips&Media, Inc.
 cortina	Cortina Systems, Inc.
 crystalfontz	Crystalfontz America, Inc.
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 91bd5bd..a3463ff 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -160,6 +160,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \
 	kirkwood-openrd-base.dtb \
 	kirkwood-openrd-client.dtb \
 	kirkwood-openrd-ultimate.dtb \
+	kirkwood-pogo_e02.dtb \
 	kirkwood-rd88f6192.dtb \
 	kirkwood-rd88f6281-z0.dtb \
 	kirkwood-rd88f6281-a.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-pogo_e02.dts b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
new file mode 100644
index 0000000..ee9eab1
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
@@ -0,0 +1,129 @@
+/*
+ * kirkwood-pogo_e02.dts - Device tree file for Pogoplug E02
+ *
+ * Copyright (C) 2015 Christoph Junghans <ottxor@gentoo.org>
+ *
+ * based on information of dts files from
+ *  Arch Linux ARM by Oleg Rakhmanov <moonman.ca@gmail.com>
+ *  OpenWrt by Felix Kaechele <heffer@fedoraproject.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Cloud Engines Pogoplug E02";
+	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	ocp at f1000000 {
+		pinctrl: pin-controller at 10000 {
+			pmx_usb_power_enable: pmx-usb-power-enable {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+			pmx_led_green: pmx-led-green {
+				marvell,pins = "mpp48";
+				marvell,function = "gpio";
+			};
+			pmx_led_orange: pmx-led-orange {
+				marvell,pins = "mpp49";
+				marvell,function = "gpio";
+			};
+		};
+		serial at 12000 {
+			status = "ok";
+		};
+	};
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
+			      &pmx_led_green >;
+		pinctrl-names = "default";
+
+		health {
+			label = "pogo_e02:green:health";
+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+		fault {
+			label = "pogo_e02:orange:fault";
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&nand {
+	chip-delay = <40>;
+	status = "okay";
+
+	partition at 0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	partition at 100000 {
+		label = "uImage";
+		reg = <0x0100000 0x400000>;
+	};
+
+	partition at 500000 {
+		label = "pogoplug";
+		reg = <0x0500000 0x2000000>;
+	};
+
+	partition at 2500000 {
+		label = "root";
+		reg = <0x02500000 0x5b00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};
-- 
2.0.5

[PATCH v3] Added support for pogoplug e02 (pink/gray)

[Andrew Lunn]

On Mon, Jan 12, 2015 at 11:13:11PM -0700, Christoph Junghans wrote:
> From: Christoph Junghans <ottxor@gentoo.org>
> 
> The pogoplug differs from the SheevaPlug only by a
> few details, but especially in the led assignments.
> This patch was tested under Gentoo Linux and is
> based on dts files from Arch Linux ARM and OpenWrt.
> 
> Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
> Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
> Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
> ---
> 
> V1: initial patch
> V2: added GPL-2 header
>     dropped earlyprintk from bootargs
>     added stdout-path
>     change leds name to scheme "devicename:colour:function"
> V3: rebase on v3.19-rc4
>     fixed stdout-path to be &uart0
>     fixed compiling issue by using pin-controller

Hi Christoph

Thanks for adding this list of changes.

> +
> +	ocp at f1000000 {
> +		pinctrl: pin-controller at 10000 {
> +			pmx_usb_power_enable: pmx-usb-power-enable {
> +				marvell,pins = "mpp29";
> +				marvell,function = "gpio";
> +			};
> +			pmx_led_green: pmx-led-green {
> +				marvell,pins = "mpp48";
> +				marvell,function = "gpio";
> +			};
> +			pmx_led_orange: pmx-led-orange {
> +				marvell,pins = "mpp49";
> +				marvell,function = "gpio";
> +			};
> +		};

Sorry, should of made myself more clear, when i pointed at:

https://lkml.org/lkml/2014/12/28/34

Please use the label for pinctl, and don't nest it under ocp at f1000000.

> +		serial at 12000 {
> +			status = "ok";
> +		};
> +	};

Same here, just

&uart0 {
	status = "okay";
};

Doing it like this is somewhat new, so most of the other kirkwood
boards don't do this. But we would like all new boards to use this
layout.

	Thanks
		Andrew

[PATCH v4] Added support for pogoplug e02 (pink/gray)

[Christoph Junghans]

The pogoplug differs from the SheevaPlug only by a
few details, but especially in the led assignments.
This patch was tested under Gentoo Linux and is
based on dts files from Arch Linux ARM and OpenWrt.

Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
---

V1: initial patch
V2: added GPL-2 header
    dropped earlyprintk from bootargs
    added stdout-path
    change leds name to scheme "devicename:colour:function"
V3: rebase on v3.19-rc4
    fixed stdout-path to be &uart0
    fixed compiling issue by using pin-controller
V4: moved ocp at f1000000 block into &uart and &pinctrl

 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/kirkwood-pogo_e02.dts            | 133 +++++++++++++++++++++
 3 files changed, 135 insertions(+)
 create mode 100644 arch/arm/boot/dts/kirkwood-pogo_e02.dts

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index b1df0ad..61888db 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -34,6 +34,7 @@ chipidea	Chipidea, Inc
 chrp	Common Hardware Reference Platform
 chunghwa	Chunghwa Picture Tubes Ltd.
 cirrus	Cirrus Logic, Inc.
+cloudengines	Cloud Engines, Inc.
 cnm	Chips&Media, Inc.
 cortina	Cortina Systems, Inc.
 crystalfontz	Crystalfontz America, Inc.
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 91bd5bd..a3463ff 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -160,6 +160,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \
 	kirkwood-openrd-base.dtb \
 	kirkwood-openrd-client.dtb \
 	kirkwood-openrd-ultimate.dtb \
+	kirkwood-pogo_e02.dtb \
 	kirkwood-rd88f6192.dtb \
 	kirkwood-rd88f6281-z0.dtb \
 	kirkwood-rd88f6281-a.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-pogo_e02.dts b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
new file mode 100644
index 0000000..b62c41c
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
@@ -0,0 +1,133 @@
+/*
+ * kirkwood-pogo_e02.dts - Device tree file for Pogoplug E02
+ *
+ * Copyright (C) 2015 Christoph Junghans <ottxor@gentoo.org>
+ *
+ * based on information of dts files from
+ *  Arch Linux ARM by Oleg Rakhmanov <moonman.ca@gmail.com>
+ *  OpenWrt by Felix Kaechele <heffer@fedoraproject.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Cloud Engines Pogoplug E02";
+	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		health {
+			label = "pogo_e02:green:health";
+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+		fault {
+			label = "pogo_e02:orange:fault";
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&pinctrl {
+	pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
+		      &pmx_led_green >;
+	pinctrl-names = "default";
+
+	pmx_usb_power_enable: pmx-usb-power-enable {
+		marvell,pins = "mpp29";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_green: pmx-led-green {
+		marvell,pins = "mpp48";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_orange: pmx-led-orange {
+		marvell,pins = "mpp49";
+		marvell,function = "gpio";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&nand {
+	chip-delay = <40>;
+	status = "okay";
+
+	partition at 0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	partition at 100000 {
+		label = "uImage";
+		reg = <0x0100000 0x400000>;
+	};
+
+	partition at 500000 {
+		label = "pogoplug";
+		reg = <0x0500000 0x2000000>;
+	};
+
+	partition at 2500000 {
+		label = "root";
+		reg = <0x02500000 0x5b00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};
-- 
2.0.5

[PATCH v4] Added support for pogoplug e02 (pink/gray)

[Andrew Lunn]

On Tue, Jan 13, 2015 at 09:49:29PM -0700, Christoph Junghans wrote:
> The pogoplug differs from the SheevaPlug only by a
> few details, but especially in the led assignments.
> This patch was tested under Gentoo Linux and is
> based on dts files from Arch Linux ARM and OpenWrt.
> 
> Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
> Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
> Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
> ---
> 
> V1: initial patch
> V2: added GPL-2 header
>     dropped earlyprintk from bootargs
>     added stdout-path
>     change leds name to scheme "devicename:colour:function"
> V3: rebase on v3.19-rc4
>     fixed stdout-path to be &uart0
>     fixed compiling issue by using pin-controller
> V4: moved ocp at f1000000 block into &uart and &pinctrl

Hi Christoph

Thanks for these last changes. It looks good now, and i've added it to
mvebu/dt. So long as there are no more comments, i will pass it
upstream soon.

Thanks
        Andrew