From: u.kleine-koenig@pengutronix.de (Uwe Kleine-König)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 0/6] mtd: teach mxc-nand about ONFI probing
Date: Mon, 2 Mar 2015 17:31:12 +0100 [thread overview]
Message-ID: <20150302163112.GF7865@pengutronix.de> (raw)
In-Reply-To: <1423594800-24214-1-git-send-email-u.kleine-koenig@pengutronix.de>
Hello,
On Tue, Feb 10, 2015 at 07:59:54PM +0100, Uwe Kleine-K?nig wrote:
> this series implements support for ONFI probing in mxc-nand.
> Before a PARAM command was just ignored and the following read_bytes
> read whatever then happened to be available from the controller's RAM.
> But actually this wasn't that bad because the driver already failed to
> read the ONFI marker at offset 32 in response to the READID command and
> so the PARAM command wasn't issued at all :-)
>
> Patch 1 is a robustness fix. Patch 2 is necessary to not make the
> controller stuck when the READPAGE command is issued before the flash
> chip is identified. Patch 3 is needed to be able to read more than 6
> bytes in the read_byte callback. Finally patch 4 fixes the driver to
> allow reading out the READID ONFI marker and patch 5 implements support
> for the PARAM command.
>
> Patch 6 implements a WARN that triggers when the core requests an
> unknown command from the driver. In the case of missing PARAM support it
> wouldn't have triggered because READID at offset 0x20 failed, too, but
> it might be worthwhile anyhow; I'm not sure though, so I marked it RFC.
> Not sure the set of commands will grow in the near future ...
>
> Best regards
> Uwe
>
> Uwe Kleine-K?nig (6):
> mtd: mxc-nand: Add a timeout when waiting for interrupt
> mtd: mxc-nand: Only enable hardware checksumming for fully detected
> flashes
> mtd: mxc-nand: Do the word to byte mangling in the read_byte callback
> mtd: mxc-nand: Allow to use column addresses different from 0
> mtd: mxc-nand: Implement support for PARAM command
> [RFC] mtd: mxc-nand: Warn on unimplemented commands
I think this series if fine to go into 4.1-rc1. If so it would be great
to get it into next in the near future. David? Brian? Any feedback?
Thanks
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | http://www.pengutronix.de/ |
next prev parent reply other threads:[~2015-03-02 16:31 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-02-10 18:59 [PATCH 0/6] mtd: teach mxc-nand about ONFI probing Uwe Kleine-König
2015-02-10 18:59 ` [PATCH 1/6] mtd: mxc-nand: Add a timeout when waiting for interrupt Uwe Kleine-König
2015-02-10 18:59 ` [PATCH 2/6] mtd: mxc-nand: Only enable hardware checksumming for fully detected flashes Uwe Kleine-König
2015-02-10 18:59 ` [PATCH 3/6] mtd: mxc-nand: Do the word to byte mangling in the read_byte callback Uwe Kleine-König
2015-02-10 18:59 ` [PATCH 4/6] mtd: mxc-nand: Allow to use column addresses different from 0 Uwe Kleine-König
2015-02-10 18:59 ` [PATCH 5/6] mtd: mxc-nand: Implement support for PARAM command Uwe Kleine-König
2015-02-10 19:00 ` [PATCH 6/6] [RFC] mtd: mxc-nand: Warn on unimplemented commands Uwe Kleine-König
2015-02-11 8:42 ` Lothar Waßmann
2015-02-11 9:00 ` Uwe Kleine-König
2015-02-11 9:40 ` Lothar Waßmann
2015-02-11 9:48 ` Uwe Kleine-König
2015-02-11 9:48 ` Sascha Hauer
2015-03-02 16:31 ` Uwe Kleine-König [this message]
2015-03-11 23:42 ` [PATCH 0/6] mtd: teach mxc-nand about ONFI probing Brian Norris
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150302163112.GF7865@pengutronix.de \
--to=u.kleine-koenig@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).