[PATCH v7 0/4] pci: iproc: Add Broadcom iProc PCIe support

[bhelgaas@google.com (Bjorn Helgaas)]

[+cc Florian]

On Thu, Mar 12, 2015 at 05:48:48PM -0700, Ray Jui wrote:
> This patch series adds the support for Broadcom iProc PCIe controller
> 
> pcie-iproc.c servers as the common core driver, and front-end bus
> interface needs to be added to support different bus interfaces
> 
> pcie-iproc-pltfm.c contains the support for the platform bus interface
> 
> Changes from v6:
>  - Fix print formatting
>  - Fix section mismatch warning by removing __init from the probe function
>  - Fix Kconfig to force it only compiling for ARM based platforms
> 
> Changes from v5:
>  - Sync code base to v4.0-rc2
>  - Change export symbols of common PCI functions to GPL only
>  - Add comment to describe how configuration register access are protected
>    at the higher layer through 'pci_lock'
>  - Use generic PCI functions for configuration register access and implement
>    'map_bus' callback to support it
>  - Move 'pci_fixup_irqs' to before devices are added to the bus
>  - Remove 'extern' from function prototype declared in the header
> 
> Changes from v4:
>  - iProc PCIe driver module support was not included in patch series v4.
>    This patch series (v5) fixes it
> 
> Changes from v3:
>  - Export symbols of several PCI functions so they can be used by drivers
>    compiled as kernel module
>  - Add additional support to the Broadcom iProc PCIe driver so it can be
>    installed/uninstalled as kernel loadable module
> 
> Changes from v2:
>  - Major rework of the PCIe driver to factor out common generic code from
>    front-end bus interface. Support for generic platform bus interface is
>    also added
>  - Adapt to several new PCI APIs that have been introduced lately
> 
> Changes from v1:
>  - Add standard PCI interrupt DT properties "#interrupt-cells",
>    "interrupt-map-mask" and "interrupt-map" so legacy INTx interrupts can be
>    supported by using standard PCI OF IRQ parsing function
>  - Get rid of custom IRQ mapping function in the driver. Use
>    of_irq_parse_and_map_pci instead
> 
> Ray Jui (4):
>   PCI: Export symbols of PCI functions
>   pci: iProc: define iProc PCIe platform bus binding
>   pci: iproc: Add Broadcom iProc PCIe support
>   ARM: dts: enable PCIe support for Cygnus

I applied patches 1-3 to pci/host-iproc for v4.1, thanks!  I didn't apply
patch 4 because Florian said he'd already applied it to devicetree/next.

I normally look for a MAINTAINERS entry, but your existing entry for
"BROADCOM CYGNUS/IPROC ARM ARCHITECTURE" has wildcards that already include
these new files.

>  .../devicetree/bindings/pci/brcm,iproc-pcie.txt    |   63 +++++
>  arch/arm/boot/dts/bcm-cygnus.dtsi                  |   42 +++
>  arch/arm/boot/dts/bcm958300k.dts                   |    8 +
>  drivers/pci/host/Kconfig                           |   17 ++
>  drivers/pci/host/Makefile                          |    2 +
>  drivers/pci/host/pcie-iproc-pltfm.c                |  108 ++++++++
>  drivers/pci/host/pcie-iproc.c                      |  268 ++++++++++++++++++++
>  drivers/pci/host/pcie-iproc.h                      |   42 +++
>  drivers/pci/pci.c                                  |    1 +
>  drivers/pci/probe.c                                |    1 +
>  drivers/pci/remove.c                               |    2 +
>  drivers/pci/setup-bus.c                            |    1 +
>  drivers/pci/setup-irq.c                            |    1 +
>  13 files changed, 556 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
>  create mode 100644 drivers/pci/host/pcie-iproc-pltfm.c
>  create mode 100644 drivers/pci/host/pcie-iproc.c
>  create mode 100644 drivers/pci/host/pcie-iproc.h
> 
> -- 
> 1.7.9.5
>