* [PATCH 01/11] ARM: shmobile: sh73a0: Introduce generic setup callback
2015-03-05 1:58 [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Simon Horman
@ 2015-03-05 1:58 ` Simon Horman
2015-03-05 1:58 ` [PATCH 02/11] ARM: shmobile: sh73a0: Add Multiplatform support Simon Horman
` (10 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Simon Horman @ 2015-03-05 1:58 UTC (permalink / raw)
To: linux-arm-kernel
From: Magnus Damm <damm+renesas@opensource.se>
Add a generic sh73a0 machine setup callback for the upcoming
sh73a0 multiplatform case. Cache needs to be configured, and
legacy clocks must be omitted.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/mach-shmobile/setup-sh73a0.c | 16 +++++++++++++---
1 file changed, 13 insertions(+), 3 deletions(-)
diff --git a/arch/arm/mach-shmobile/setup-sh73a0.c b/arch/arm/mach-shmobile/setup-sh73a0.c
index faea74a..48f2447 100644
--- a/arch/arm/mach-shmobile/setup-sh73a0.c
+++ b/arch/arm/mach-shmobile/setup-sh73a0.c
@@ -30,6 +30,7 @@
#include <linux/platform_data/sh_ipmmu.h>
#include <linux/platform_data/irq-renesas-intc-irqpin.h>
+#include <asm/hardware/cache-l2x0.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/mach/arch.h>
@@ -782,8 +783,6 @@ void __init sh73a0_add_early_devices(void)
shmobile_setup_console();
}
-#ifdef CONFIG_USE_OF
-
void __init sh73a0_add_standard_devices_dt(void)
{
/* clocks are setup late during boot in the case of DT */
@@ -800,6 +799,17 @@ static void sh73a0_restart(enum reboot_mode mode, const char *cmd)
writel((1 << 31), RESCNT2);
}
+#ifdef CONFIG_USE_OF
+
+static void __init sh73a0_generic_init(void)
+{
+#ifdef CONFIG_CACHE_L2X0
+ /* Shared attribute override enable, 64K*8way */
+ l2x0_init(IOMEM(0xf0100000), 0x00400000, 0xc20f0fff);
+#endif
+ of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+}
+
static const char *sh73a0_boards_compat_dt[] __initdata = {
"renesas,sh73a0",
NULL,
@@ -809,7 +819,7 @@ DT_MACHINE_START(SH73A0_DT, "Generic SH73A0 (Flattened Device Tree)")
.smp = smp_ops(sh73a0_smp_ops),
.map_io = sh73a0_map_io,
.init_early = shmobile_init_delay,
- .init_machine = sh73a0_add_standard_devices_dt,
+ .init_machine = sh73a0_generic_init,
.init_late = shmobile_init_late,
.restart = sh73a0_restart,
.dt_compat = sh73a0_boards_compat_dt,
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 02/11] ARM: shmobile: sh73a0: Add Multiplatform support
2015-03-05 1:58 [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Simon Horman
2015-03-05 1:58 ` [PATCH 01/11] ARM: shmobile: sh73a0: Introduce generic setup callback Simon Horman
@ 2015-03-05 1:58 ` Simon Horman
2015-03-05 1:58 ` [PATCH 03/11] ARM: shmobile: kzm9g dts: Sync with kzm9g-reference dts Simon Horman
` (9 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Simon Horman @ 2015-03-05 1:58 UTC (permalink / raw)
To: linux-arm-kernel
From: Magnus Damm <damm+renesas@opensource.se>
Enable sh73a0 Multiplatform support for the generic sh73a0
machine vector. No board support is enabled, and the board
code for KZM9G DT Reference is left by itself.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/mach-shmobile/Kconfig | 5 +++++
arch/arm/mach-shmobile/Makefile | 4 ++--
arch/arm/mach-shmobile/smp-sh73a0.c | 2 +-
3 files changed, 8 insertions(+), 3 deletions(-)
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 2f36c85..8ee2f28 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -78,6 +78,11 @@ config ARCH_R8A7794
bool "R-Car E2 (R8A77940)"
select ARCH_RCAR_GEN2
+config ARCH_SH73A0
+ bool "SH-Mobile AG5 (R8A73A00)"
+ select ARCH_RMOBILE
+ select RENESAS_INTC_IRQPIN
+
comment "Renesas ARM SoCs Board Type"
config MACH_MARZEN
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index d53996e..b400f5f 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -7,7 +7,7 @@ obj-y := timer.o console.o
# CPU objects
obj-$(CONFIG_ARCH_SH7372) += setup-sh7372.o intc-sh7372.o pm-sh7372.o
-obj-$(CONFIG_ARCH_SH73A0) += setup-sh73a0.o intc-sh73a0.o pm-sh73a0.o
+obj-$(CONFIG_ARCH_SH73A0) += setup-sh73a0.o pm-sh73a0.o
obj-$(CONFIG_ARCH_R8A73A4) += setup-r8a73a4.o
obj-$(CONFIG_ARCH_R8A7740) += setup-r8a7740.o pm-r8a7740.o
obj-$(CONFIG_ARCH_R8A7778) += setup-r8a7778.o
@@ -65,7 +65,7 @@ obj-$(CONFIG_MACH_BOCKW) += board-bockw.o
obj-$(CONFIG_MACH_BOCKW_REFERENCE) += board-bockw-reference.o
obj-$(CONFIG_MACH_MARZEN) += board-marzen.o
obj-$(CONFIG_MACH_ARMADILLO800EVA) += board-armadillo800eva.o
-obj-$(CONFIG_MACH_KZM9G) += board-kzm9g.o
+obj-$(CONFIG_MACH_KZM9G) += board-kzm9g.o intc-sh73a0.o
obj-$(CONFIG_MACH_KZM9G_REFERENCE) += board-kzm9g-reference.o
endif
diff --git a/arch/arm/mach-shmobile/smp-sh73a0.c b/arch/arm/mach-shmobile/smp-sh73a0.c
index c16dbfe..2106d6b 100644
--- a/arch/arm/mach-shmobile/smp-sh73a0.c
+++ b/arch/arm/mach-shmobile/smp-sh73a0.c
@@ -33,7 +33,7 @@
#define SH73A0_SCU_BASE 0xf0000000
-#ifdef CONFIG_HAVE_ARM_TWD
+#if defined(CONFIG_HAVE_ARM_TWD) && !defined(CONFIG_ARCH_MULTIPLATFORM)
static DEFINE_TWD_LOCAL_TIMER(twd_local_timer, SH73A0_SCU_BASE + 0x600, 29);
void __init sh73a0_register_twd(void)
{
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 03/11] ARM: shmobile: kzm9g dts: Sync with kzm9g-reference dts
2015-03-05 1:58 [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Simon Horman
2015-03-05 1:58 ` [PATCH 01/11] ARM: shmobile: sh73a0: Introduce generic setup callback Simon Horman
2015-03-05 1:58 ` [PATCH 02/11] ARM: shmobile: sh73a0: Add Multiplatform support Simon Horman
@ 2015-03-05 1:58 ` Simon Horman
2015-03-05 1:58 ` [PATCH 04/11] ARM: shmobile: kzm9g: Build DTS for Multiplatform Simon Horman
` (8 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Simon Horman @ 2015-03-05 1:58 UTC (permalink / raw)
To: linux-arm-kernel
From: Magnus Damm <damm+renesas@opensource.se>
Sync the two DTS for the KZM9G board. The target is the file
"sh73a0-kzm9g.dts" and it is made identical to the DT reference
case with the exception of the compatbile string. In the future
the DT reference file will go away.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[geert: Update for recent changes to sh73a0-kzm9g-reference.dts]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/sh73a0-kzm9g.dts | 374 ++++++++++++++++++++++++++++++++++++-
1 file changed, 373 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/sh73a0-kzm9g.dts b/arch/arm/boot/dts/sh73a0-kzm9g.dts
index e7dae01..6f00e6b 100644
--- a/arch/arm/boot/dts/sh73a0-kzm9g.dts
+++ b/arch/arm/boot/dts/sh73a0-kzm9g.dts
@@ -1,6 +1,9 @@
/*
* Device Tree Source for the KZM-A9-GT board
*
+ * Copyright (C) 2012 Horms Solutions Ltd.
+ *
+ * Based on sh73a0-kzm9g.dts
* Copyright (C) 2012 Renesas Solutions Corp.
*
* This file is licensed under the terms of the GNU General Public License
@@ -10,17 +13,386 @@
/dts-v1/;
#include "sh73a0.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "KZM-A9-GT";
compatible = "renesas,kzm9g", "renesas,sh73a0";
+ aliases {
+ serial4 = &scifa4;
+ };
+
+ cpus {
+ cpu at 0 {
+ cpu0-supply = <&vdd_dvfs>;
+ operating-points = <
+ /* kHz uV */
+ 1196000 1315000
+ 598000 1175000
+ 398667 1065000
+ >;
+ voltage-tolerance = <1>; /* 1% */
+ };
+ };
+
chosen {
- bootargs = "console=tty0 console=ttySC4,115200 root=/dev/nfs ip=dhcp ignore_loglevel earlyprintk=sh-sci.4,115200 rw";
+ bootargs = "console=tty0 console=ttySC4,115200 root=/dev/nfs ip=dhcp ignore_loglevel rw";
+ stdout-path = &scifa4;
};
memory {
device_type = "memory";
reg = <0x40000000 0x20000000>;
};
+
+ reg_1p8v: regulator at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reg_3p3v: regulator at 1 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vmmc_sdhi0: regulator at 2 {
+ compatible = "regulator-fixed";
+ regulator-name = "SDHI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pfc 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vmmc_sdhi2: regulator at 3 {
+ compatible = "regulator-fixed";
+ regulator-name = "SDHI2 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pfc 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ lan9220 at 10000000 {
+ compatible = "smsc,lan9220", "smsc,lan9115";
+ reg = <0x10000000 0x100>;
+ phy-mode = "mii";
+ interrupt-parent = <&irqpin0>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+ reg-io-width = <4>;
+ smsc,irq-push-pull;
+ smsc,save-mac-address;
+ vddvario-supply = <®_1p8v>;
+ vdd33a-supply = <®_3p3v>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led1 {
+ gpios = <&pfc 20 GPIO_ACTIVE_LOW>;
+ label = "LED1";
+ };
+ led2 {
+ gpios = <&pfc 21 GPIO_ACTIVE_LOW>;
+ label = "LED2";
+ };
+ led3 {
+ gpios = <&pfc 22 GPIO_ACTIVE_LOW>;
+ label = "LED3";
+ };
+ led4 {
+ gpios = <&pfc 23 GPIO_ACTIVE_LOW>;
+ label = "LED4";
+ };
+ };
+
+ keyboard {
+ compatible = "gpio-keys";
+
+ back-key {
+ gpios = <&pcf8575 8 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_BACK>;
+ label = "SW3";
+ };
+
+ right-key {
+ gpios = <&pcf8575 9 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RIGHT>;
+ label = "SW2-R";
+ };
+
+ left-key {
+ gpios = <&pcf8575 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_LEFT>;
+ label = "SW2-L";
+ };
+
+ enter-key {
+ gpios = <&pcf8575 11 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_ENTER>;
+ label = "SW2-P";
+ };
+
+ up-key {
+ gpios = <&pcf8575 12 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_UP>;
+ label = "SW2-U";
+ };
+
+ down-key {
+ gpios = <&pcf8575 13 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_DOWN>;
+ label = "SW2-D";
+ };
+
+ home-key {
+ gpios = <&pcf8575 14 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOME>;
+ label = "SW1";
+ };
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "left_j";
+ simple-audio-card,cpu {
+ sound-dai = <&sh_fsi2 0>;
+ };
+ simple-audio-card,codec {
+ sound-dai = <&ak4648>;
+ bitclock-master;
+ frame-master;
+ system-clock-frequency = <11289600>;
+ };
+ };
+};
+
+&cmt1 {
+ status = "okay";
+};
+
+&extal2_clk {
+ clock-frequency = <48000000>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ compass at c {
+ compatible = "asahi-kasei,ak8975";
+ reg = <0x0c>;
+ interrupt-parent = <&irqpin3>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+ };
+
+ ak4648: codec at 12 {
+ compatible = "asahi-kasei,ak4648";
+ reg = <0x12>;
+ #sound-dai-cells = <0>;
+ };
+
+ accelerometer at 1d {
+ compatible = "adi,adxl34x";
+ reg = <0x1d>;
+ interrupt-parent = <&irqpin3>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH>,
+ <3 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ rtc at 32 {
+ compatible = "ricoh,r2025sd";
+ reg = <0x32>;
+ };
+
+ as3711 at 40 {
+ compatible = "ams,as3711";
+ reg = <0x40>;
+
+ regulators {
+ vdd_dvfs: sd1 {
+ regulator-name = "1.315V CPU";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ sd2 {
+ regulator-name = "1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ sd4 {
+ regulator-name = "1.215V";
+ regulator-min-microvolt = <1215000>;
+ regulator-max-microvolt = <1235000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ ldo2 {
+ regulator-name = "2.8V CPU";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ ldo3 {
+ regulator-name = "3.0V CPU";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ ldo4 {
+ regulator-name = "2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ ldo5 {
+ regulator-name = "2.8V #2";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ ldo7 {
+ regulator-name = "1.15V CPU";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ ldo8 {
+ regulator-name = "1.15V CPU #2";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ touchscreen at 55 {
+ compatible = "sitronix,st1232";
+ reg = <0x55>;
+ interrupt-parent = <&irqpin1>;
+ interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&i2c3 {
+ pinctrl-0 = <&i2c3_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ pcf8575: gpio at 20 {
+ compatible = "nxp,pcf8575";
+ reg = <0x20>;
+ interrupt-parent = <&irqpin2>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&mmcif {
+ pinctrl-0 = <&mmcif_pins>;
+ pinctrl-names = "default";
+
+ bus-width = <8>;
+ vmmc-supply = <®_1p8v>;
+ status = "okay";
+};
+
+&pfc {
+ i2c3_pins: i2c3 {
+ renesas,groups = "i2c3_1";
+ renesas,function = "i2c3";
+ };
+
+ mmcif_pins: mmc {
+ mux {
+ renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0";
+ renesas,function = "mmc0";
+ };
+ cfg {
+ renesas,groups = "mmc0_data8_0";
+ renesas,pins = "PORT279";
+ bias-pull-up;
+ };
+ };
+
+ scifa4_pins: serial4 {
+ renesas,groups = "scifa4_data", "scifa4_ctrl";
+ renesas,function = "scifa4";
+ };
+
+ sdhi0_pins: sd0 {
+ renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_cd", "sdhi0_wp";
+ renesas,function = "sdhi0";
+ };
+
+ sdhi2_pins: sd2 {
+ renesas,groups = "sdhi2_data4", "sdhi2_ctrl";
+ renesas,function = "sdhi2";
+ };
+
+ fsia_pins: sounda {
+ renesas,groups = "fsia_mclk_in", "fsia_sclk_in",
+ "fsia_data_in", "fsia_data_out";
+ renesas,function = "fsia";
+ };
+};
+
+&scifa4 {
+ pinctrl-0 = <&scifa4_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_pins>;
+ pinctrl-names = "default";
+
+ vmmc-supply = <&vmmc_sdhi0>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&sdhi2 {
+ pinctrl-0 = <&sdhi2_pins>;
+ pinctrl-names = "default";
+
+ vmmc-supply = <&vmmc_sdhi2>;
+ bus-width = <4>;
+ broken-cd;
+ status = "okay";
+};
+
+&sh_fsi2 {
+ pinctrl-0 = <&fsia_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
};
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 04/11] ARM: shmobile: kzm9g: Build DTS for Multiplatform
2015-03-05 1:58 [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Simon Horman
` (2 preceding siblings ...)
2015-03-05 1:58 ` [PATCH 03/11] ARM: shmobile: kzm9g dts: Sync with kzm9g-reference dts Simon Horman
@ 2015-03-05 1:58 ` Simon Horman
2015-03-05 1:58 ` [PATCH 05/11] ARM: shmobile: sh73a0 dtsi: Add Bus State Controller node Simon Horman
` (7 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Simon Horman @ 2015-03-05 1:58 UTC (permalink / raw)
To: linux-arm-kernel
From: Magnus Damm <damm+renesas@opensource.se>
Build the sh73a0 KZM9G board DTB in case of Multiplatform.
The DT reference case will be removed in the future and
can be ignored for now.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/Makefile | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a1c776b..287ebca 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -482,7 +482,8 @@ dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \
r8a7790-lager.dtb \
r8a7791-henninger.dtb \
r8a7791-koelsch.dtb \
- r8a7794-alt.dtb
+ r8a7794-alt.dtb \
+ sh73a0-kzm9g.dtb
dtb-$(CONFIG_ARCH_SOCFPGA) += \
socfpga_arria5_socdk.dtb \
socfpga_arria10_socdk.dtb \
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 05/11] ARM: shmobile: sh73a0 dtsi: Add Bus State Controller node
2015-03-05 1:58 [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Simon Horman
` (3 preceding siblings ...)
2015-03-05 1:58 ` [PATCH 04/11] ARM: shmobile: kzm9g: Build DTS for Multiplatform Simon Horman
@ 2015-03-05 1:58 ` Simon Horman
2015-03-05 1:58 ` [PATCH 06/11] ARM: shmobile: kzm9g dts: Move Ethernet node to BSC Simon Horman
` (6 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Simon Horman @ 2015-03-05 1:58 UTC (permalink / raw)
To: linux-arm-kernel
From: Geert Uytterhoeven <geert+renesas@glider.be>
Add a node for the Bus State Controller (BSC) on sh73a0, to which
multiple external devices can be connected.
The BSC is driven by the ZB clock, and located in PM domain A4S.
A reference to the latter will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/sh73a0.dtsi | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm/boot/dts/sh73a0.dtsi b/arch/arm/boot/dts/sh73a0.dtsi
index ab319b7..70b694f 100644
--- a/arch/arm/boot/dts/sh73a0.dtsi
+++ b/arch/arm/boot/dts/sh73a0.dtsi
@@ -376,6 +376,17 @@
status = "disabled";
};
+ bsc: bus at fec10000 {
+ compatible = "renesas,bsc-sh73a0", "renesas,bsc",
+ "simple-pm-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0x20000000>;
+ reg = <0xfec10000 0x400>;
+ interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&zb_clk>;
+ };
+
clocks {
#address-cells = <1>;
#size-cells = <1>;
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 06/11] ARM: shmobile: kzm9g dts: Move Ethernet node to BSC
2015-03-05 1:58 [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Simon Horman
` (4 preceding siblings ...)
2015-03-05 1:58 ` [PATCH 05/11] ARM: shmobile: sh73a0 dtsi: Add Bus State Controller node Simon Horman
@ 2015-03-05 1:58 ` Simon Horman
2015-03-05 1:58 ` [PATCH 07/11] ARM: shmobile: kzm9g-reference: Remove board C code and DT file Simon Horman
` (5 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Simon Horman @ 2015-03-05 1:58 UTC (permalink / raw)
To: linux-arm-kernel
From: Geert Uytterhoeven <geert+renesas@glider.be>
Move the Ethernet node from the root of the device tree to the BSC node,
as it's connected to the Bus State Controller. This allows the system
to know the right position of the Ethernet node in the clock and PM
domain hierarchy, and manage the clock and PM domain appropriately.
Also rename the node's name from "lan9220" to "ethernet", to conform to
ePAPR generic name recomendations.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/sh73a0-kzm9g.dts | 28 +++++++++++++++-------------
1 file changed, 15 insertions(+), 13 deletions(-)
diff --git a/arch/arm/boot/dts/sh73a0-kzm9g.dts b/arch/arm/boot/dts/sh73a0-kzm9g.dts
index 6f00e6b..022ba50 100644
--- a/arch/arm/boot/dts/sh73a0-kzm9g.dts
+++ b/arch/arm/boot/dts/sh73a0-kzm9g.dts
@@ -84,19 +84,6 @@
enable-active-high;
};
- lan9220 at 10000000 {
- compatible = "smsc,lan9220", "smsc,lan9115";
- reg = <0x10000000 0x100>;
- phy-mode = "mii";
- interrupt-parent = <&irqpin0>;
- interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
- reg-io-width = <4>;
- smsc,irq-push-pull;
- smsc,save-mac-address;
- vddvario-supply = <®_1p8v>;
- vdd33a-supply = <®_3p3v>;
- };
-
leds {
compatible = "gpio-leds";
led1 {
@@ -178,6 +165,21 @@
};
};
+&bsc {
+ ethernet at 10000000 {
+ compatible = "smsc,lan9220", "smsc,lan9115";
+ reg = <0x10000000 0x100>;
+ phy-mode = "mii";
+ interrupt-parent = <&irqpin0>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+ reg-io-width = <4>;
+ smsc,irq-push-pull;
+ smsc,save-mac-address;
+ vddvario-supply = <®_1p8v>;
+ vdd33a-supply = <®_3p3v>;
+ };
+};
+
&cmt1 {
status = "okay";
};
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 07/11] ARM: shmobile: kzm9g-reference: Remove board C code and DT file
2015-03-05 1:58 [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Simon Horman
` (5 preceding siblings ...)
2015-03-05 1:58 ` [PATCH 06/11] ARM: shmobile: kzm9g dts: Move Ethernet node to BSC Simon Horman
@ 2015-03-05 1:58 ` Simon Horman
2015-03-05 1:58 ` [PATCH 08/11] ARM: shmobile: sh73a0 dtsi: Add Cortex-A9 TWD node Simon Horman
` (4 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Simon Horman @ 2015-03-05 1:58 UTC (permalink / raw)
To: linux-arm-kernel
Now that the sh73a0 generic multiplatform case has the same feature set
as the kzm9g DT reference board code, we get rid of the latter.
DT reference code in the future shall make use of the sh73a0
multiplatform support code with the generic SoC machine vector.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
Documentation/devicetree/bindings/arm/shmobile.txt | 2 -
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/sh73a0-kzm9g-reference.dts | 398 ---------------------
arch/arm/mach-shmobile/Kconfig | 14 -
arch/arm/mach-shmobile/Makefile | 1 -
arch/arm/mach-shmobile/Makefile.boot | 1 -
arch/arm/mach-shmobile/board-kzm9g-reference.c | 62 ----
arch/arm/mach-shmobile/include/mach/zboot.h | 2 +-
8 files changed, 2 insertions(+), 481 deletions(-)
delete mode 100644 arch/arm/boot/dts/sh73a0-kzm9g-reference.dts
delete mode 100644 arch/arm/mach-shmobile/board-kzm9g-reference.c
diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt
index 51147cb..c69f127 100644
--- a/Documentation/devicetree/bindings/arm/shmobile.txt
+++ b/Documentation/devicetree/bindings/arm/shmobile.txt
@@ -57,8 +57,6 @@ Boards:
compatible = "renesas,kzm9d", "renesas,emev2"
- Kyoto Microcomputer Co. KZM-A9-GT
compatible = "renesas,kzm9g", "renesas,sh73a0"
- - Kyoto Microcomputer Co. KZM-A9-GT - Reference Device Tree Implementation
- compatible = "renesas,kzm9g-reference", "renesas,sh73a0"
- Lager (RTP0RC7790SEB00010S)
compatible = "renesas,lager", "renesas,r8a7790"
- Mackerel (R0P7372LC0016RL, AP4 EVM 2nd)
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 287ebca..aa26d13 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -471,8 +471,7 @@ dtb-$(CONFIG_ARCH_SHMOBILE_LEGACY) += \
r8a7778-bockw-reference.dtb \
r8a7779-marzen.dtb \
sh7372-mackerel.dtb \
- sh73a0-kzm9g.dtb \
- sh73a0-kzm9g-reference.dtb
+ sh73a0-kzm9g.dtb
dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \
emev2-kzm9d.dtb \
r7s72100-genmai.dtb \
diff --git a/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts b/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts
deleted file mode 100644
index bf365f7..0000000
--- a/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts
+++ /dev/null
@@ -1,398 +0,0 @@
-/*
- * Device Tree Source for the KZM-A9-GT board
- *
- * Copyright (C) 2012 Horms Solutions Ltd.
- *
- * Based on sh73a0-kzm9g.dts
- * Copyright (C) 2012 Renesas Solutions Corp.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-/dts-v1/;
-#include "sh73a0.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-
-/ {
- model = "KZM-A9-GT";
- compatible = "renesas,kzm9g-reference", "renesas,sh73a0";
-
- aliases {
- serial4 = &scifa4;
- };
-
- cpus {
- cpu at 0 {
- cpu0-supply = <&vdd_dvfs>;
- operating-points = <
- /* kHz uV */
- 1196000 1315000
- 598000 1175000
- 398667 1065000
- >;
- voltage-tolerance = <1>; /* 1% */
- };
- };
-
- chosen {
- bootargs = "console=tty0 console=ttySC4,115200 root=/dev/nfs ip=dhcp ignore_loglevel rw";
- stdout-path = &scifa4;
- };
-
- memory {
- device_type = "memory";
- reg = <0x40000000 0x20000000>;
- };
-
- reg_1p8v: regulator at 0 {
- compatible = "regulator-fixed";
- regulator-name = "fixed-1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- reg_3p3v: regulator at 1 {
- compatible = "regulator-fixed";
- regulator-name = "fixed-3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- vmmc_sdhi0: regulator at 2 {
- compatible = "regulator-fixed";
- regulator-name = "SDHI0 Vcc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&pfc 15 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vmmc_sdhi2: regulator at 3 {
- compatible = "regulator-fixed";
- regulator-name = "SDHI2 Vcc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&pfc 14 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- lan9220 at 10000000 {
- compatible = "smsc,lan9220", "smsc,lan9115";
- reg = <0x10000000 0x100>;
- phy-mode = "mii";
- interrupt-parent = <&irqpin0>;
- interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
- reg-io-width = <4>;
- smsc,irq-push-pull;
- smsc,save-mac-address;
- vddvario-supply = <®_1p8v>;
- vdd33a-supply = <®_3p3v>;
- };
-
- leds {
- compatible = "gpio-leds";
- led1 {
- gpios = <&pfc 20 GPIO_ACTIVE_LOW>;
- label = "LED1";
- };
- led2 {
- gpios = <&pfc 21 GPIO_ACTIVE_LOW>;
- label = "LED2";
- };
- led3 {
- gpios = <&pfc 22 GPIO_ACTIVE_LOW>;
- label = "LED3";
- };
- led4 {
- gpios = <&pfc 23 GPIO_ACTIVE_LOW>;
- label = "LED4";
- };
- };
-
- keyboard {
- compatible = "gpio-keys";
-
- back-key {
- gpios = <&pcf8575 8 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_BACK>;
- label = "SW3";
- };
-
- right-key {
- gpios = <&pcf8575 9 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RIGHT>;
- label = "SW2-R";
- };
-
- left-key {
- gpios = <&pcf8575 10 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_LEFT>;
- label = "SW2-L";
- };
-
- enter-key {
- gpios = <&pcf8575 11 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_ENTER>;
- label = "SW2-P";
- };
-
- up-key {
- gpios = <&pcf8575 12 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_UP>;
- label = "SW2-U";
- };
-
- down-key {
- gpios = <&pcf8575 13 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_DOWN>;
- label = "SW2-D";
- };
-
- home-key {
- gpios = <&pcf8575 14 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_HOME>;
- label = "SW1";
- };
- };
-
- sound {
- compatible = "simple-audio-card";
- simple-audio-card,format = "left_j";
- simple-audio-card,cpu {
- sound-dai = <&sh_fsi2 0>;
- };
- simple-audio-card,codec {
- sound-dai = <&ak4648>;
- bitclock-master;
- frame-master;
- system-clock-frequency = <11289600>;
- };
- };
-};
-
-&cmt1 {
- status = "okay";
-};
-
-&extal2_clk {
- clock-frequency = <48000000>;
-};
-
-&i2c0 {
- status = "okay";
-
- compass at c {
- compatible = "asahi-kasei,ak8975";
- reg = <0x0c>;
- interrupt-parent = <&irqpin3>;
- interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
- };
-
- ak4648: codec at 12 {
- compatible = "asahi-kasei,ak4648";
- reg = <0x12>;
- #sound-dai-cells = <0>;
- };
-
- accelerometer at 1d {
- compatible = "adi,adxl34x";
- reg = <0x1d>;
- interrupt-parent = <&irqpin3>;
- interrupts = <2 IRQ_TYPE_LEVEL_HIGH>,
- <3 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- rtc at 32 {
- compatible = "ricoh,r2025sd";
- reg = <0x32>;
- };
-
- as3711 at 40 {
- compatible = "ams,as3711";
- reg = <0x40>;
-
- regulators {
- vdd_dvfs: sd1 {
- regulator-name = "1.315V CPU";
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
- sd2 {
- regulator-name = "1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
- sd4 {
- regulator-name = "1.215V";
- regulator-min-microvolt = <1215000>;
- regulator-max-microvolt = <1235000>;
- regulator-always-on;
- regulator-boot-on;
- };
- ldo2 {
- regulator-name = "2.8V CPU";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- regulator-boot-on;
- };
- ldo3 {
- regulator-name = "3.0V CPU";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-always-on;
- regulator-boot-on;
- };
- ldo4 {
- regulator-name = "2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- regulator-boot-on;
- };
- ldo5 {
- regulator-name = "2.8V #2";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- regulator-boot-on;
- };
- ldo7 {
- regulator-name = "1.15V CPU";
- regulator-min-microvolt = <1150000>;
- regulator-max-microvolt = <1150000>;
- regulator-always-on;
- regulator-boot-on;
- };
- ldo8 {
- regulator-name = "1.15V CPU #2";
- regulator-min-microvolt = <1150000>;
- regulator-max-microvolt = <1150000>;
- regulator-always-on;
- regulator-boot-on;
- };
- };
- };
-};
-
-&i2c1 {
- status = "okay";
-
- touchscreen at 55 {
- compatible = "sitronix,st1232";
- reg = <0x55>;
- interrupt-parent = <&irqpin1>;
- interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
- };
-};
-
-&i2c3 {
- pinctrl-0 = <&i2c3_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- pcf8575: gpio at 20 {
- compatible = "nxp,pcf8575";
- reg = <0x20>;
- interrupt-parent = <&irqpin2>;
- interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-};
-
-&mmcif {
- pinctrl-0 = <&mmcif_pins>;
- pinctrl-names = "default";
-
- bus-width = <8>;
- vmmc-supply = <®_1p8v>;
- status = "okay";
-};
-
-&pfc {
- i2c3_pins: i2c3 {
- renesas,groups = "i2c3_1";
- renesas,function = "i2c3";
- };
-
- mmcif_pins: mmc {
- mux {
- renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0";
- renesas,function = "mmc0";
- };
- cfg {
- renesas,groups = "mmc0_data8_0";
- renesas,pins = "PORT279";
- bias-pull-up;
- };
- };
-
- scifa4_pins: serial4 {
- renesas,groups = "scifa4_data", "scifa4_ctrl";
- renesas,function = "scifa4";
- };
-
- sdhi0_pins: sd0 {
- renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_cd", "sdhi0_wp";
- renesas,function = "sdhi0";
- };
-
- sdhi2_pins: sd2 {
- renesas,groups = "sdhi2_data4", "sdhi2_ctrl";
- renesas,function = "sdhi2";
- };
-
- fsia_pins: sounda {
- renesas,groups = "fsia_mclk_in", "fsia_sclk_in",
- "fsia_data_in", "fsia_data_out";
- renesas,function = "fsia";
- };
-};
-
-&scifa4 {
- pinctrl-0 = <&scifa4_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
-
-&sdhi0 {
- pinctrl-0 = <&sdhi0_pins>;
- pinctrl-names = "default";
-
- vmmc-supply = <&vmmc_sdhi0>;
- bus-width = <4>;
- status = "okay";
-};
-
-&sdhi2 {
- pinctrl-0 = <&sdhi2_pins>;
- pinctrl-names = "default";
-
- vmmc-supply = <&vmmc_sdhi2>;
- bus-width = <4>;
- broken-cd;
- status = "okay";
-};
-
-&sh_fsi2 {
- pinctrl-0 = <&fsia_pins>;
- pinctrl-names = "default";
-
- status = "okay";
-};
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 8ee2f28..f4108d8 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -214,20 +214,6 @@ config MACH_KZM9G
select SND_SOC_AK4642 if SND_SIMPLE_CARD
select USE_OF
-config MACH_KZM9G_REFERENCE
- bool "KZM-A9-GT board - Reference Device Tree Implementation"
- depends on ARCH_SH73A0
- select ARCH_REQUIRE_GPIOLIB
- select REGULATOR_FIXED_VOLTAGE if REGULATOR
- select SND_SOC_AK4642 if SND_SIMPLE_CARD
- select USE_OF
- ---help---
- Use reference implementation of KZM-A9-GT board support
- which makes as greater use of device tree at the expense
- of not supporting a number of devices.
-
- This is intended to aid developers
-
comment "Renesas ARM SoCs System Configuration"
config CPU_HAS_INTEVT
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index b400f5f..7b9ed9e 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -66,7 +66,6 @@ obj-$(CONFIG_MACH_BOCKW_REFERENCE) += board-bockw-reference.o
obj-$(CONFIG_MACH_MARZEN) += board-marzen.o
obj-$(CONFIG_MACH_ARMADILLO800EVA) += board-armadillo800eva.o
obj-$(CONFIG_MACH_KZM9G) += board-kzm9g.o intc-sh73a0.o
-obj-$(CONFIG_MACH_KZM9G_REFERENCE) += board-kzm9g-reference.o
endif
# Framework support
diff --git a/arch/arm/mach-shmobile/Makefile.boot b/arch/arm/mach-shmobile/Makefile.boot
index 02532be..6ef0e2b 100644
--- a/arch/arm/mach-shmobile/Makefile.boot
+++ b/arch/arm/mach-shmobile/Makefile.boot
@@ -6,7 +6,6 @@ loadaddr-$(CONFIG_MACH_ARMADILLO800EVA) += 0x40008000
loadaddr-$(CONFIG_MACH_BOCKW) += 0x60008000
loadaddr-$(CONFIG_MACH_BOCKW_REFERENCE) += 0x60008000
loadaddr-$(CONFIG_MACH_KZM9G) += 0x41008000
-loadaddr-$(CONFIG_MACH_KZM9G_REFERENCE) += 0x41008000
loadaddr-$(CONFIG_MACH_MACKEREL) += 0x40008000
loadaddr-$(CONFIG_MACH_MARZEN) += 0x60008000
diff --git a/arch/arm/mach-shmobile/board-kzm9g-reference.c b/arch/arm/mach-shmobile/board-kzm9g-reference.c
deleted file mode 100644
index 2e82e44..0000000
--- a/arch/arm/mach-shmobile/board-kzm9g-reference.c
+++ /dev/null
@@ -1,62 +0,0 @@
-/*
- * KZM-A9-GT board support - Reference Device Tree Implementation
- *
- * Copyright (C) 2012 Horms Solutions Ltd.
- *
- * Based on board-kzm9g.c
- * Copyright (C) 2012 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/input.h>
-#include <linux/of_platform.h>
-
-#include <asm/hardware/cache-l2x0.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "common.h"
-#include "sh73a0.h"
-
-static void __init kzm_init(void)
-{
- sh73a0_add_standard_devices_dt();
-
-#ifdef CONFIG_CACHE_L2X0
- /* Shared attribute override enable, 64K*8way */
- l2x0_init(IOMEM(0xf0100000), 0x00400000, 0xc20f0fff);
-#endif
-}
-
-#define RESCNT2 IOMEM(0xe6188020)
-static void kzm9g_restart(enum reboot_mode mode, const char *cmd)
-{
- /* Do soft power on reset */
- writel((1 << 31), RESCNT2);
-}
-
-static const char *kzm9g_boards_compat_dt[] __initdata = {
- "renesas,kzm9g-reference",
- NULL,
-};
-
-DT_MACHINE_START(KZM9G_DT, "kzm9g-reference")
- .smp = smp_ops(sh73a0_smp_ops),
- .map_io = sh73a0_map_io,
- .init_early = shmobile_init_delay,
- .init_machine = kzm_init,
- .init_late = shmobile_init_late,
- .restart = kzm9g_restart,
- .dt_compat = kzm9g_boards_compat_dt,
-MACHINE_END
diff --git a/arch/arm/mach-shmobile/include/mach/zboot.h b/arch/arm/mach-shmobile/include/mach/zboot.h
index 727cc78..219bbcf 100644
--- a/arch/arm/mach-shmobile/include/mach/zboot.h
+++ b/arch/arm/mach-shmobile/include/mach/zboot.h
@@ -12,7 +12,7 @@
#ifdef CONFIG_MACH_MACKEREL
#define MEMORY_START 0x40000000
#include "mach/head-mackerel.txt"
-#elif defined(CONFIG_MACH_KZM9G) || defined(CONFIG_MACH_KZM9G_REFERENCE)
+#elif defined(CONFIG_MACH_KZM9G)
#define MEMORY_START 0x43000000
#include "mach/head-kzm9g.txt"
#else
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 08/11] ARM: shmobile: sh73a0 dtsi: Add Cortex-A9 TWD node
2015-03-05 1:58 [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Simon Horman
` (6 preceding siblings ...)
2015-03-05 1:58 ` [PATCH 07/11] ARM: shmobile: kzm9g-reference: Remove board C code and DT file Simon Horman
@ 2015-03-05 1:58 ` Simon Horman
2015-03-05 1:58 ` [PATCH 09/11] ARM: shmobile: sh73a0: Remove unused sh73a0_add_standard_devices_dt() Simon Horman
` (3 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Simon Horman @ 2015-03-05 1:58 UTC (permalink / raw)
To: linux-arm-kernel
From: Geert Uytterhoeven <geert+renesas@glider.be>
Add a node for the Private Timer and Watchdog, as found in the Cortex-A9
MPCore.
Without this, there's no clocksource available during early kernel
initialization, before cmt1 is initialized, leading to a lock-up if
CONFIG_CPU_IDLE=y.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/sh73a0.dtsi | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm/boot/dts/sh73a0.dtsi b/arch/arm/boot/dts/sh73a0.dtsi
index 70b694f..0b933e2 100644
--- a/arch/arm/boot/dts/sh73a0.dtsi
+++ b/arch/arm/boot/dts/sh73a0.dtsi
@@ -11,6 +11,7 @@
/include/ "skeleton.dtsi"
#include <dt-bindings/clock/sh73a0-clock.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
/ {
@@ -35,6 +36,13 @@
};
};
+ timer at f0000600 {
+ compatible = "arm,cortex-a9-twd-timer";
+ reg = <0xf0000600 0x20>;
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+ clocks = <&twd_clk>;
+ };
+
gic: interrupt-controller at f0001000 {
compatible = "arm,cortex-a9-gic";
#interrupt-cells = <3>;
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 09/11] ARM: shmobile: sh73a0: Remove unused sh73a0_add_standard_devices_dt()
2015-03-05 1:58 [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Simon Horman
` (7 preceding siblings ...)
2015-03-05 1:58 ` [PATCH 08/11] ARM: shmobile: sh73a0 dtsi: Add Cortex-A9 TWD node Simon Horman
@ 2015-03-05 1:58 ` Simon Horman
2015-03-05 1:58 ` [PATCH 10/11] ARM: shmobile: sh73a0 dtsi: Add PM domain support Simon Horman
` (2 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Simon Horman @ 2015-03-05 1:58 UTC (permalink / raw)
To: linux-arm-kernel
From: Geert Uytterhoeven <geert+renesas@glider.be>
"ARM: shmobile: kzm9g-reference: Remove board C code and DT file"
removed the last user of sh73a0_add_standard_devices_dt(). Hence remove
this function.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/mach-shmobile/setup-sh73a0.c | 9 ---------
arch/arm/mach-shmobile/sh73a0.h | 1 -
2 files changed, 10 deletions(-)
diff --git a/arch/arm/mach-shmobile/setup-sh73a0.c b/arch/arm/mach-shmobile/setup-sh73a0.c
index 48f2447..2f68459e 100644
--- a/arch/arm/mach-shmobile/setup-sh73a0.c
+++ b/arch/arm/mach-shmobile/setup-sh73a0.c
@@ -783,15 +783,6 @@ void __init sh73a0_add_early_devices(void)
shmobile_setup_console();
}
-void __init sh73a0_add_standard_devices_dt(void)
-{
- /* clocks are setup late during boot in the case of DT */
-#ifndef CONFIG_COMMON_CLK
- sh73a0_clock_init();
-#endif
- of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
-}
-
#define RESCNT2 IOMEM(0xe6188020)
static void sh73a0_restart(enum reboot_mode mode, const char *cmd)
{
diff --git a/arch/arm/mach-shmobile/sh73a0.h b/arch/arm/mach-shmobile/sh73a0.h
index f037c64..5a80f18 100644
--- a/arch/arm/mach-shmobile/sh73a0.h
+++ b/arch/arm/mach-shmobile/sh73a0.h
@@ -77,7 +77,6 @@ extern void sh73a0_map_io(void);
extern void sh73a0_earlytimer_init(void);
extern void sh73a0_add_early_devices(void);
extern void sh73a0_add_standard_devices(void);
-extern void sh73a0_add_standard_devices_dt(void);
extern void sh73a0_clock_init(void);
extern void sh73a0_pinmux_init(void);
extern void sh73a0_pm_init(void);
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 10/11] ARM: shmobile: sh73a0 dtsi: Add PM domain support
2015-03-05 1:58 [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Simon Horman
` (8 preceding siblings ...)
2015-03-05 1:58 ` [PATCH 09/11] ARM: shmobile: sh73a0: Remove unused sh73a0_add_standard_devices_dt() Simon Horman
@ 2015-03-05 1:58 ` Simon Horman
2015-03-05 1:58 ` [PATCH 11/11] ARM: shmobile: sh73a0: Remove restart callback Simon Horman
2015-04-01 23:38 ` [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Olof Johansson
11 siblings, 0 replies; 13+ messages in thread
From: Simon Horman @ 2015-03-05 1:58 UTC (permalink / raw)
To: linux-arm-kernel
From: Geert Uytterhoeven <geert+renesas@glider.be>
Add a device node for the System Controller, with subnodes that
represent the hardware power area hierarchy.
Hook up all devices to their respective PM domains.
Note that unlike on R-Mobile A1 (r8a7740), PM domain D4 can be powered
down without ill effects on s2ram behavior, just like on SH-Mobile AP4
(sh7372). Hence we can postpone adding a (minimal) device node for the
Coresight-ETM hardware block.
The System Controller is also used by the R-Mobile Reset driver, which
can now restart the system.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/sh73a0.dtsi | 144 +++++++++++++++++++++++++++++++++++++++++-
1 file changed, 142 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/sh73a0.dtsi b/arch/arm/boot/dts/sh73a0.dtsi
index 0b933e2..45b539c 100644
--- a/arch/arm/boot/dts/sh73a0.dtsi
+++ b/arch/arm/boot/dts/sh73a0.dtsi
@@ -27,12 +27,14 @@
compatible = "arm,cortex-a9";
reg = <0>;
clock-frequency = <1196000000>;
+ power-domains = <&pd_a2sl>;
};
cpu at 1 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <1>;
clock-frequency = <1196000000>;
+ power-domains = <&pd_a2sl>;
};
};
@@ -57,6 +59,7 @@
interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>,
<0 38 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "sec", "temp";
+ power-domains = <&pd_a4bc1>;
};
sbsc1: memory-controller at fe400000 {
@@ -65,6 +68,7 @@
interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>,
<0 36 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "sec", "temp";
+ power-domains = <&pd_a4bc0>;
};
pmu {
@@ -77,11 +81,12 @@
compatible = "renesas,cmt-48-sh73a0", "renesas,cmt-48";
reg = <0xe6138000 0x200>;
interrupts = <0 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp3_clks SH73A0_CLK_CMT1>;
+ clock-names = "fck";
+ power-domains = <&pd_c5>;
renesas,channels-mask = <0x3f>;
- clocks = <&mstp3_clks SH73A0_CLK_CMT1>;
- clock-names = "fck";
status = "disabled";
};
@@ -103,6 +108,7 @@
0 7 IRQ_TYPE_LEVEL_HIGH
0 8 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp5_clks SH73A0_CLK_INTCA0>;
+ power-domains = <&pd_a4s>;
control-parent;
};
@@ -124,6 +130,7 @@
0 15 IRQ_TYPE_LEVEL_HIGH
0 16 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp5_clks SH73A0_CLK_INTCA0>;
+ power-domains = <&pd_a4s>;
control-parent;
};
@@ -145,6 +152,7 @@
0 23 IRQ_TYPE_LEVEL_HIGH
0 24 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp5_clks SH73A0_CLK_INTCA0>;
+ power-domains = <&pd_a4s>;
control-parent;
};
@@ -166,6 +174,7 @@
0 31 IRQ_TYPE_LEVEL_HIGH
0 32 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp5_clks SH73A0_CLK_INTCA0>;
+ power-domains = <&pd_a4s>;
control-parent;
};
@@ -179,6 +188,7 @@
0 169 IRQ_TYPE_LEVEL_HIGH
0 170 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks SH73A0_CLK_IIC0>;
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -192,6 +202,7 @@
0 53 IRQ_TYPE_LEVEL_HIGH
0 54 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks SH73A0_CLK_IIC1>;
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -205,6 +216,7 @@
0 173 IRQ_TYPE_LEVEL_HIGH
0 174 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks SH73A0_CLK_IIC2>;
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -218,6 +230,7 @@
0 185 IRQ_TYPE_LEVEL_HIGH
0 186 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp4_clks SH73A0_CLK_IIC3>;
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -231,6 +244,7 @@
0 189 IRQ_TYPE_LEVEL_HIGH
0 190 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp4_clks SH73A0_CLK_IIC4>;
+ power-domains = <&pd_c5>;
status = "disabled";
};
@@ -240,6 +254,7 @@
interrupts = <0 140 IRQ_TYPE_LEVEL_HIGH
0 141 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks SH73A0_CLK_MMCIF0>;
+ power-domains = <&pd_a3sp>;
reg-io-width = <4>;
status = "disabled";
};
@@ -251,6 +266,7 @@
0 84 IRQ_TYPE_LEVEL_HIGH
0 85 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks SH73A0_CLK_SDHI0>;
+ power-domains = <&pd_a3sp>;
cap-sd-highspeed;
status = "disabled";
};
@@ -262,6 +278,7 @@
interrupts = <0 88 IRQ_TYPE_LEVEL_HIGH
0 89 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks SH73A0_CLK_SDHI1>;
+ power-domains = <&pd_a3sp>;
toshiba,mmc-wrprotect-disable;
cap-sd-highspeed;
status = "disabled";
@@ -273,6 +290,7 @@
interrupts = <0 104 IRQ_TYPE_LEVEL_HIGH
0 105 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks SH73A0_CLK_SDHI2>;
+ power-domains = <&pd_a3sp>;
toshiba,mmc-wrprotect-disable;
cap-sd-highspeed;
status = "disabled";
@@ -284,6 +302,7 @@
interrupts = <0 72 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks SH73A0_CLK_SCIFA0>;
clock-names = "sci_ick";
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -293,6 +312,7 @@
interrupts = <0 73 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks SH73A0_CLK_SCIFA1>;
clock-names = "sci_ick";
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -302,6 +322,7 @@
interrupts = <0 74 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks SH73A0_CLK_SCIFA2>;
clock-names = "sci_ick";
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -311,6 +332,7 @@
interrupts = <0 75 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks SH73A0_CLK_SCIFA3>;
clock-names = "sci_ick";
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -320,6 +342,7 @@
interrupts = <0 78 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks SH73A0_CLK_SCIFA4>;
clock-names = "sci_ick";
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -329,6 +352,7 @@
interrupts = <0 79 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks SH73A0_CLK_SCIFA5>;
clock-names = "sci_ick";
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -338,6 +362,7 @@
interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks SH73A0_CLK_SCIFA6>;
clock-names = "sci_ick";
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -347,6 +372,7 @@
interrupts = <0 143 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks SH73A0_CLK_SCIFA7>;
clock-names = "sci_ick";
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -356,6 +382,7 @@
interrupts = <0 80 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks SH73A0_CLK_SCIFB>;
clock-names = "sci_ick";
+ power-domains = <&pd_a3sp>;
status = "disabled";
};
@@ -374,6 +401,117 @@
<&irqpin2 4 0>, <&irqpin2 5 0>, <&irqpin2 6 0>, <&irqpin2 7 0>,
<&irqpin3 0 0>, <&irqpin3 1 0>, <&irqpin3 2 0>, <&irqpin3 3 0>,
<&irqpin3 4 0>, <&irqpin3 5 0>, <&irqpin3 6 0>, <&irqpin3 7 0>;
+ power-domains = <&pd_c5>;
+ };
+
+ sysc: system-controller at e6180000 {
+ compatible = "renesas,sysc-sh73a0", "renesas,sysc-rmobile";
+ reg = <0xe6180000 0x8000>, <0xe6188000 0x8000>;
+
+ pm-domains {
+ pd_c5: c5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #power-domain-cells = <0>;
+
+ pd_c4: c4 at 0 {
+ reg = <0>;
+ #power-domain-cells = <0>;
+ };
+
+ pd_d4: d4 at 1 {
+ reg = <1>;
+ #power-domain-cells = <0>;
+ };
+
+ pd_a4bc0: a4bc0 at 4 {
+ reg = <4>;
+ #power-domain-cells = <0>;
+ };
+
+ pd_a4bc1: a4bc1 at 5 {
+ reg = <5>;
+ #power-domain-cells = <0>;
+ };
+
+ pd_a4lc0: a4lc0 at 6 {
+ reg = <6>;
+ #power-domain-cells = <0>;
+ };
+
+ pd_a4lc1: a4lc1 at 7 {
+ reg = <7>;
+ #power-domain-cells = <0>;
+ };
+
+ pd_a4mp: a4mp at 8 {
+ reg = <8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #power-domain-cells = <0>;
+
+ pd_a3mp: a3mp at 9 {
+ reg = <9>;
+ #power-domain-cells = <0>;
+ };
+
+ pd_a3vc: a3vc at 10 {
+ reg = <10>;
+ #power-domain-cells = <0>;
+ };
+ };
+
+ pd_a4rm: a4rm at 12 {
+ reg = <12>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #power-domain-cells = <0>;
+
+ pd_a3r: a3r at 13 {
+ reg = <13>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #power-domain-cells = <0>;
+
+ pd_a2rv: a2rv at 14 {
+ reg = <14>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #power-domain-cells = <0>;
+ };
+ };
+ };
+
+ pd_a4s: a4s at 16 {
+ reg = <16>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #power-domain-cells = <0>;
+
+ pd_a3sp: a3sp at 17 {
+ reg = <17>;
+ #power-domain-cells = <0>;
+ };
+
+ pd_a3sg: a3sg at 18 {
+ reg = <18>;
+ #power-domain-cells = <0>;
+ };
+
+ pd_a3sm: a3sm at 19 {
+ reg = <19>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #power-domain-cells = <0>;
+
+ pd_a2sl: a2sl at 20 {
+ reg = <20>;
+ #power-domain-cells = <0>;
+ };
+ };
+ };
+ };
+ };
};
sh_fsi2: sound at ec230000 {
@@ -381,6 +519,7 @@
compatible = "renesas,fsi2-sh73a0", "renesas,sh_fsi2";
reg = <0xec230000 0x400>;
interrupts = <0 146 0x4>;
+ power-domains = <&pd_a4mp>;
status = "disabled";
};
@@ -393,6 +532,7 @@
reg = <0xfec10000 0x400>;
interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&zb_clk>;
+ power-domains = <&pd_a4s>;
};
clocks {
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 11/11] ARM: shmobile: sh73a0: Remove restart callback
2015-03-05 1:58 [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Simon Horman
` (9 preceding siblings ...)
2015-03-05 1:58 ` [PATCH 10/11] ARM: shmobile: sh73a0 dtsi: Add PM domain support Simon Horman
@ 2015-03-05 1:58 ` Simon Horman
2015-04-01 23:38 ` [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Olof Johansson
11 siblings, 0 replies; 13+ messages in thread
From: Simon Horman @ 2015-03-05 1:58 UTC (permalink / raw)
To: linux-arm-kernel
From: Geert Uytterhoeven <geert+renesas@glider.be>
Remove the restart handling hack from the sh73a0 generic multiplatform
case.
Restart on DT-based sh73a0 platforms is now handled through the
R-Mobile reset driver.
This basically reverts commit cad900819fba0176 ("ARM: shmobile: sh73a0:
Add restart callback").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/mach-shmobile/setup-sh73a0.c | 8 --------
1 file changed, 8 deletions(-)
diff --git a/arch/arm/mach-shmobile/setup-sh73a0.c b/arch/arm/mach-shmobile/setup-sh73a0.c
index 2f68459e..fb2ab75 100644
--- a/arch/arm/mach-shmobile/setup-sh73a0.c
+++ b/arch/arm/mach-shmobile/setup-sh73a0.c
@@ -783,13 +783,6 @@ void __init sh73a0_add_early_devices(void)
shmobile_setup_console();
}
-#define RESCNT2 IOMEM(0xe6188020)
-static void sh73a0_restart(enum reboot_mode mode, const char *cmd)
-{
- /* Do soft power on reset */
- writel((1 << 31), RESCNT2);
-}
-
#ifdef CONFIG_USE_OF
static void __init sh73a0_generic_init(void)
@@ -812,7 +805,6 @@ DT_MACHINE_START(SH73A0_DT, "Generic SH73A0 (Flattened Device Tree)")
.init_early = shmobile_init_delay,
.init_machine = sh73a0_generic_init,
.init_late = shmobile_init_late,
- .restart = sh73a0_restart,
.dt_compat = sh73a0_boards_compat_dt,
MACHINE_END
#endif /* CONFIG_USE_OF */
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1
2015-03-05 1:58 [GIT PULL] Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1 Simon Horman
` (10 preceding siblings ...)
2015-03-05 1:58 ` [PATCH 11/11] ARM: shmobile: sh73a0: Remove restart callback Simon Horman
@ 2015-04-01 23:38 ` Olof Johansson
11 siblings, 0 replies; 13+ messages in thread
From: Olof Johansson @ 2015-04-01 23:38 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Mar 05, 2015 at 10:58:26AM +0900, Simon Horman wrote:
> Hi Olof, Hi Kevin, Hi Arnd,
>
> Please consider these Renesas ARM based SoC sh73a0 multiplatform updates for v4.1.
>
> This pull request is based on the previous round of
> such requests, tagged as sh73a0-multiplatform-for-v4.1.base,
> which I have already sent a pull-request for.
>
>
> This pull request is based on a merge of the following pull requests
> which you have already pulled:
>
> * "Renesas ARM Based SoC Simple PM Bus Updates for v4.1",
> tagged as renesas-simple-pm-bus-for-v4.1.
>
> * "Renesas ARM Based SoC DT Updates for v4.1", tagged as renesas-dt-for-v4.1.
>
>
> This pull requests has a number of minor conflicts with "Renesas ARM Based
> SoC sh7372 SoC Removal Updates for v4.1", tagged as
> renesas-sh7372-soc-removal-for-v4.1, which you have already pulled.
>
> The conflicts are in the following files:
> arch/arm/boot/dts/Makefile
> arch/arm/mach-shmobile/Makefile
> arch/arm/mach-shmobile/Makefile.boot
> arch/arm/mach-shmobile/include/mach/zboot.h
It'd be nice to keep the dts changes in your DT branch, so there's less risk
for add/remove conflicts. I don't think there will be any this release so it's
not a big deal, but keep it in mind in the future.
Also, as already mentioned, some of this could have gone in one larger joined
branch (and based on the cleanups to avoid conflicts).
-Olof
^ permalink raw reply [flat|nested] 13+ messages in thread