* [PATCH v4 01/13] ARM: dts: Add labels to Exynos4 nodes
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
2015-05-13 8:59 ` Kukjin Kim
2015-05-11 13:42 ` [PATCH v4 02/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Krzysztof Kozlowski
` (11 subsequent siblings)
12 siblings, 1 reply; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Add new labels to certain nodes so they could be easily referenced by
Exynos4 board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4.dtsi | 22 +++++++++++-----------
arch/arm/boot/dts/exynos4210-pinctrl.dtsi | 6 +++---
arch/arm/boot/dts/exynos4210.dtsi | 6 +++---
arch/arm/boot/dts/exynos4x12-pinctrl.dtsi | 8 ++++----
arch/arm/boot/dts/exynos4x12.dtsi | 2 +-
5 files changed, 22 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi
index 1c74c1296ab7..0ec292d25b6e 100644
--- a/arch/arm/boot/dts/exynos4.dtsi
+++ b/arch/arm/boot/dts/exynos4.dtsi
@@ -257,7 +257,7 @@
};
};
- watchdog at 10060000 {
+ watchdog: watchdog at 10060000 {
compatible = "samsung,s3c2410-wdt";
reg = <0x10060000 0x100>;
interrupts = <0 43 0>;
@@ -276,7 +276,7 @@
status = "disabled";
};
- keypad at 100A0000 {
+ keypad: keypad at 100A0000 {
compatible = "samsung,s5pv210-keypad";
reg = <0x100A0000 0x100>;
interrupts = <0 109 0>;
@@ -285,7 +285,7 @@
status = "disabled";
};
- sdhci at 12510000 {
+ sdhci_0: sdhci at 12510000 {
compatible = "samsung,exynos4210-sdhci";
reg = <0x12510000 0x100>;
interrupts = <0 73 0>;
@@ -294,7 +294,7 @@
status = "disabled";
};
- sdhci at 12520000 {
+ sdhci_1: sdhci at 12520000 {
compatible = "samsung,exynos4210-sdhci";
reg = <0x12520000 0x100>;
interrupts = <0 74 0>;
@@ -303,7 +303,7 @@
status = "disabled";
};
- sdhci at 12530000 {
+ sdhci_2: sdhci at 12530000 {
compatible = "samsung,exynos4210-sdhci";
reg = <0x12530000 0x100>;
interrupts = <0 75 0>;
@@ -312,7 +312,7 @@
status = "disabled";
};
- sdhci at 12540000 {
+ sdhci_3: sdhci at 12540000 {
compatible = "samsung,exynos4210-sdhci";
reg = <0x12540000 0x100>;
interrupts = <0 76 0>;
@@ -331,7 +331,7 @@
status = "disabled";
};
- hsotg at 12480000 {
+ hsotg: hsotg at 12480000 {
compatible = "samsung,s3c6400-hsotg";
reg = <0x12480000 0x20000>;
interrupts = <0 71 0>;
@@ -342,7 +342,7 @@
status = "disabled";
};
- ehci at 12580000 {
+ ehci: ehci at 12580000 {
compatible = "samsung,exynos4210-ehci";
reg = <0x12580000 0x100>;
interrupts = <0 70 0>;
@@ -368,7 +368,7 @@
};
};
- ohci at 12590000 {
+ ohci: ohci at 12590000 {
compatible = "samsung,exynos4210-ohci";
reg = <0x12590000 0x100>;
interrupts = <0 70 0>;
@@ -621,7 +621,7 @@
status = "disabled";
};
- pwm at 139D0000 {
+ pwm: pwm at 139D0000 {
compatible = "samsung,exynos4210-pwm";
reg = <0x139D0000 0x1000>;
interrupts = <0 37 0>, <0 38 0>, <0 39 0>, <0 40 0>, <0 41 0>;
@@ -689,7 +689,7 @@
#include "exynos4412-tmu-sensor-conf.dtsi"
};
- jpeg-codec at 11840000 {
+ jpeg_codec: jpeg-codec at 11840000 {
compatible = "samsung,exynos4210-jpeg";
reg = <0x11840000 0x1000>;
interrupts = <0 88 0>;
diff --git a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
index a7c212891674..4704e7bb2628 100644
--- a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
@@ -15,7 +15,7 @@
*/
/ {
- pinctrl at 11400000 {
+ pinctrl_0: pinctrl at 11400000 {
gpa0: gpa0 {
gpio-controller;
#gpio-cells = <2>;
@@ -421,7 +421,7 @@
};
};
- pinctrl at 11000000 {
+ pinctrl_1: pinctrl at 11000000 {
gpj0: gpj0 {
gpio-controller;
#gpio-cells = <2>;
@@ -822,7 +822,7 @@
};
};
- pinctrl at 03860000 {
+ pinctrl_3: pinctrl at 03860000 {
gpz: gpz {
gpio-controller;
#gpio-cells = <2>;
diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi
index be89f83f70e7..76b84852f29c 100644
--- a/arch/arm/boot/dts/exynos4210.dtsi
+++ b/arch/arm/boot/dts/exynos4210.dtsi
@@ -62,7 +62,7 @@
#clock-cells = <1>;
};
- sysram at 02020000 {
+ sysram: sysram at 02020000 {
compatible = "mmio-sram";
reg = <0x02020000 0x20000>;
#address-cells = <1>;
@@ -107,7 +107,7 @@
<0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
};
- mct at 10050000 {
+ mct: mct at 10050000 {
compatible = "samsung,exynos4210-mct";
reg = <0x10050000 0x800>;
interrupt-parent = <&mct_map>;
@@ -189,7 +189,7 @@
};
};
- g2d at 12800000 {
+ g2d: g2d at 12800000 {
compatible = "samsung,s5pv210-g2d";
reg = <0x12800000 0x1000>;
interrupts = <0 89 0>;
diff --git a/arch/arm/boot/dts/exynos4x12-pinctrl.dtsi b/arch/arm/boot/dts/exynos4x12-pinctrl.dtsi
index c141931378e7..bac25c672789 100644
--- a/arch/arm/boot/dts/exynos4x12-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos4x12-pinctrl.dtsi
@@ -29,7 +29,7 @@
}
/ {
- pinctrl at 11400000 {
+ pinctrl_0: pinctrl at 11400000 {
gpa0: gpa0 {
gpio-controller;
#gpio-cells = <2>;
@@ -441,7 +441,7 @@
};
};
- pinctrl at 11000000 {
+ pinctrl_1: pinctrl at 11000000 {
gpk0: gpk0 {
gpio-controller;
#gpio-cells = <2>;
@@ -887,7 +887,7 @@
};
};
- pinctrl at 03860000 {
+ pinctrl_2: pinctrl at 03860000 {
gpz: gpz {
gpio-controller;
#gpio-cells = <2>;
@@ -913,7 +913,7 @@
};
};
- pinctrl at 106E0000 {
+ pinctrl_3: pinctrl at 106E0000 {
gpv0: gpv0 {
gpio-controller;
#gpio-cells = <2>;
diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi
index 72b9a1d744fa..8cd27641cfb7 100644
--- a/arch/arm/boot/dts/exynos4x12.dtsi
+++ b/arch/arm/boot/dts/exynos4x12.dtsi
@@ -159,7 +159,7 @@
#clock-cells = <1>;
};
- g2d at 10800000 {
+ g2d: g2d at 10800000 {
compatible = "samsung,exynos4212-g2d";
reg = <0x10800000 0x1000>;
interrupts = <0 89 0>;
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v4 01/13] ARM: dts: Add labels to Exynos4 nodes
2015-05-11 13:42 ` [PATCH v4 01/13] ARM: dts: Add labels to Exynos4 nodes Krzysztof Kozlowski
@ 2015-05-13 8:59 ` Kukjin Kim
2015-05-13 9:42 ` Krzysztof Kozłowski
0 siblings, 1 reply; 21+ messages in thread
From: Kukjin Kim @ 2015-05-13 8:59 UTC (permalink / raw)
To: linux-arm-kernel
On 05/11/15 22:42, Krzysztof Kozlowski wrote:
> Add new labels to certain nodes so they could be easily referenced by
> Exynos4 board DTS files.
>
> Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
> ---
> arch/arm/boot/dts/exynos4.dtsi | 22 +++++++++++-----------
> arch/arm/boot/dts/exynos4210-pinctrl.dtsi | 6 +++---
> arch/arm/boot/dts/exynos4210.dtsi | 6 +++---
> arch/arm/boot/dts/exynos4x12-pinctrl.dtsi | 8 ++++----
> arch/arm/boot/dts/exynos4x12.dtsi | 2 +-
> 5 files changed, 22 insertions(+), 22 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi
> index 1c74c1296ab7..0ec292d25b6e 100644
> --- a/arch/arm/boot/dts/exynos4.dtsi
> +++ b/arch/arm/boot/dts/exynos4.dtsi
[...]
> diff --git a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
> index a7c212891674..4704e7bb2628 100644
> --- a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
> +++ b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
> @@ -15,7 +15,7 @@
> */
>
> / {
> - pinctrl at 11400000 {
> + pinctrl_0: pinctrl at 11400000 {
> gpa0: gpa0 {
> gpio-controller;
> #gpio-cells = <2>;
> @@ -421,7 +421,7 @@
> };
> };
>
> - pinctrl at 11000000 {
> + pinctrl_1: pinctrl at 11000000 {
> gpj0: gpj0 {
> gpio-controller;
> #gpio-cells = <2>;
> @@ -822,7 +822,7 @@
> };
> };
>
> - pinctrl at 03860000 {
> + pinctrl_3: pinctrl at 03860000 {
Maybe,
+ pinctrl_2: pinctrl at 03860000 { ?
> gpz: gpz {
> gpio-controller;
> #gpio-cells = <2>;
[...]
- Kukjin
^ permalink raw reply [flat|nested] 21+ messages in thread* [PATCH v4 01/13] ARM: dts: Add labels to Exynos4 nodes
2015-05-13 8:59 ` Kukjin Kim
@ 2015-05-13 9:42 ` Krzysztof Kozłowski
0 siblings, 0 replies; 21+ messages in thread
From: Krzysztof Kozłowski @ 2015-05-13 9:42 UTC (permalink / raw)
To: linux-arm-kernel
2015-05-13 17:59 GMT+09:00 Kukjin Kim <kgene@kernel.org>:
> On 05/11/15 22:42, Krzysztof Kozlowski wrote:
>> Add new labels to certain nodes so they could be easily referenced by
>> Exynos4 board DTS files.
>>
>> Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
>> ---
>> arch/arm/boot/dts/exynos4.dtsi | 22 +++++++++++-----------
>> arch/arm/boot/dts/exynos4210-pinctrl.dtsi | 6 +++---
>> arch/arm/boot/dts/exynos4210.dtsi | 6 +++---
>> arch/arm/boot/dts/exynos4x12-pinctrl.dtsi | 8 ++++----
>> arch/arm/boot/dts/exynos4x12.dtsi | 2 +-
>> 5 files changed, 22 insertions(+), 22 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi
>> index 1c74c1296ab7..0ec292d25b6e 100644
>> --- a/arch/arm/boot/dts/exynos4.dtsi
>> +++ b/arch/arm/boot/dts/exynos4.dtsi
>
> [...]
>
>> diff --git a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
>> index a7c212891674..4704e7bb2628 100644
>> --- a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
>> +++ b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
>> @@ -15,7 +15,7 @@
>> */
>>
>> / {
>> - pinctrl at 11400000 {
>> + pinctrl_0: pinctrl at 11400000 {
>> gpa0: gpa0 {
>> gpio-controller;
>> #gpio-cells = <2>;
>> @@ -421,7 +421,7 @@
>> };
>> };
>>
>> - pinctrl at 11000000 {
>> + pinctrl_1: pinctrl at 11000000 {
>> gpj0: gpj0 {
>> gpio-controller;
>> #gpio-cells = <2>;
>> @@ -822,7 +822,7 @@
>> };
>> };
>>
>> - pinctrl at 03860000 {
>> + pinctrl_3: pinctrl at 03860000 {
>
> Maybe,
> + pinctrl_2: pinctrl at 03860000 { ?
Yes, you are right. Actually I made mistake here because in
exynos4210.dtsi these labels are defined.
I will fix it and re-spin.
Thanks for feedback,
Krzysztof
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH v4 02/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
2015-05-11 13:42 ` [PATCH v4 01/13] ARM: dts: Add labels to Exynos4 nodes Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
2015-05-13 9:02 ` [PATCH v4 02/13] ARM: dts: exynos4: Use labels for overriding nodesin Exynos4210 Kukjin Kim
2015-05-11 13:42 ` [PATCH v4 03/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Origen Krzysztof Kozlowski
` (10 subsequent siblings)
12 siblings, 1 reply; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4210.dtsi | 43 +++++++++++++++++++--------------------
1 file changed, 21 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi
index 76b84852f29c..a9a55304e31a 100644
--- a/arch/arm/boot/dts/exynos4210.dtsi
+++ b/arch/arm/boot/dts/exynos4210.dtsi
@@ -52,16 +52,6 @@
};
};
- pmu_system_controller: system-controller at 10020000 {
- clock-names = "clkout0", "clkout1", "clkout2", "clkout3",
- "clkout4", "clkout8", "clkout9";
- clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>,
- <&clock CLK_OUT_LEFTBUS>, <&clock CLK_OUT_RIGHTBUS>,
- <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>,
- <&clock CLK_XUSBXTI>;
- #clock-cells = <1>;
- };
-
sysram: sysram at 02020000 {
compatible = "mmio-sram";
reg = <0x02020000 0x20000>;
@@ -95,18 +85,6 @@
arm,data-latency = <2 2 1>;
};
- gic: interrupt-controller at 10490000 {
- cpu-offset = <0x8000>;
- };
-
- combiner: interrupt-controller at 10440000 {
- samsung,combiner-nr = <16>;
- interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
- <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
- <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
- <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
- };
-
mct: mct at 10050000 {
compatible = "samsung,exynos4210-mct";
reg = <0x10050000 0x800>;
@@ -245,3 +223,24 @@
status = "disabled";
};
};
+
+&gic {
+ cpu-offset = <0x8000>;
+};
+
+&combiner {
+ samsung,combiner-nr = <16>;
+ interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+ <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+ <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+ <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
+};
+
+&pmu_system_controller {
+ clock-names = "clkout0", "clkout1", "clkout2", "clkout3",
+ "clkout4", "clkout8", "clkout9";
+ clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>,
+ <&clock CLK_OUT_LEFTBUS>, <&clock CLK_OUT_RIGHTBUS>,
+ <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>, <&clock CLK_XUSBXTI>;
+ #clock-cells = <1>;
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v4 02/13] ARM: dts: exynos4: Use labels for overriding nodesin Exynos4210
2015-05-11 13:42 ` [PATCH v4 02/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Krzysztof Kozlowski
@ 2015-05-13 9:02 ` Kukjin Kim
2015-05-13 9:51 ` Krzysztof Kozlowski
0 siblings, 1 reply; 21+ messages in thread
From: Kukjin Kim @ 2015-05-13 9:02 UTC (permalink / raw)
To: linux-arm-kernel
On 05/11/15 22:42, Krzysztof Kozlowski wrote:
> Usage of labels instead of full paths reduces possible mistakes when
> overriding nodes.
>
Well, I'm not sure what kind of the possible mistakes you mentioned...?
I don't think we need to use the label for gic, combiner.
- Kukjin
> Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
> ---
> arch/arm/boot/dts/exynos4210.dtsi | 43 +++++++++++++++++++--------------------
> 1 file changed, 21 insertions(+), 22 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi
> index 76b84852f29c..a9a55304e31a 100644
> --- a/arch/arm/boot/dts/exynos4210.dtsi
> +++ b/arch/arm/boot/dts/exynos4210.dtsi
> @@ -52,16 +52,6 @@
> };
> };
>
> - pmu_system_controller: system-controller at 10020000 {
> - clock-names = "clkout0", "clkout1", "clkout2", "clkout3",
> - "clkout4", "clkout8", "clkout9";
> - clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>,
> - <&clock CLK_OUT_LEFTBUS>, <&clock CLK_OUT_RIGHTBUS>,
> - <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>,
> - <&clock CLK_XUSBXTI>;
> - #clock-cells = <1>;
> - };
> -
> sysram: sysram at 02020000 {
> compatible = "mmio-sram";
> reg = <0x02020000 0x20000>;
> @@ -95,18 +85,6 @@
> arm,data-latency = <2 2 1>;
> };
>
> - gic: interrupt-controller at 10490000 {
> - cpu-offset = <0x8000>;
> - };
> -
> - combiner: interrupt-controller at 10440000 {
> - samsung,combiner-nr = <16>;
> - interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
> - <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
> - <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
> - <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
> - };
> -
> mct: mct at 10050000 {
> compatible = "samsung,exynos4210-mct";
> reg = <0x10050000 0x800>;
> @@ -245,3 +223,24 @@
> status = "disabled";
> };
> };
> +
> +&gic {
> + cpu-offset = <0x8000>;
> +};
> +
> +&combiner {
> + samsung,combiner-nr = <16>;
> + interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
> + <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
> + <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
> + <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
> +};
> +
> +&pmu_system_controller {
> + clock-names = "clkout0", "clkout1", "clkout2", "clkout3",
> + "clkout4", "clkout8", "clkout9";
> + clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>,
> + <&clock CLK_OUT_LEFTBUS>, <&clock CLK_OUT_RIGHTBUS>,
> + <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>, <&clock CLK_XUSBXTI>;
> + #clock-cells = <1>;
> +};
^ permalink raw reply [flat|nested] 21+ messages in thread* [PATCH v4 02/13] ARM: dts: exynos4: Use labels for overriding nodesin Exynos4210
2015-05-13 9:02 ` [PATCH v4 02/13] ARM: dts: exynos4: Use labels for overriding nodesin Exynos4210 Kukjin Kim
@ 2015-05-13 9:51 ` Krzysztof Kozlowski
0 siblings, 0 replies; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-13 9:51 UTC (permalink / raw)
To: linux-arm-kernel
W dniu 13.05.2015 o 18:02, Kukjin Kim pisze:
> On 05/11/15 22:42, Krzysztof Kozlowski wrote:
>> Usage of labels instead of full paths reduces possible mistakes when
>> overriding nodes.
>>
> Well, I'm not sure what kind of the possible mistakes you mentioned...?
One can make a mistake in path when overriding. For example we have:
exynos4.dtsi:
/ {
gic: interrupt-controller at 10490000 {
...
};
}
and someone can add in child dtsi (like exynos4210.dtsi):
/ {
soc {
interrupt-controller at 10490000 {
cpu-offset = <0x8000>;
}
}
}
or he can make a mistake in address.
As a result the gic node won't be properly overridden.
>
> I don't think we need to use the label for gic, combiner.
They are overridden by child DTSI. First definition is in exynos4.dtsi
and exynos4210.dtsi adds a cpu-offset.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH v4 03/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Origen
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
2015-05-11 13:42 ` [PATCH v4 01/13] ARM: dts: Add labels to Exynos4 nodes Krzysztof Kozlowski
2015-05-11 13:42 ` [PATCH v4 02/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
2015-05-13 9:11 ` Kukjin Kim
2015-05-11 13:42 ` [PATCH v4 04/13] ARM: dts: exynos4: Use labels for overriding nodes in SMDKv310 Krzysztof Kozlowski
` (9 subsequent siblings)
12 siblings, 1 reply; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4210-origen.dts | 418 ++++++++++++++++----------------
1 file changed, 209 insertions(+), 209 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts
index b81146141402..e0abfc3324d1 100644
--- a/arch/arm/boot/dts/exynos4210-origen.dts
+++ b/arch/arm/boot/dts/exynos4210-origen.dts
@@ -50,209 +50,6 @@
};
};
- watchdog at 10060000 {
- status = "okay";
- };
-
- rtc at 10070000 {
- status = "okay";
- };
-
- tmu at 100C0000 {
- status = "okay";
- };
-
- sdhci at 12530000 {
- bus-width = <4>;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
- pinctrl-names = "default";
- vmmc-supply = <&mmc_reg>;
- status = "okay";
- };
-
- sdhci at 12510000 {
- bus-width = <4>;
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_cd>;
- pinctrl-names = "default";
- vmmc-supply = <&mmc_reg>;
- status = "okay";
- };
-
- g2d at 12800000 {
- status = "okay";
- };
-
- codec at 13400000 {
- samsung,mfc-r = <0x43000000 0x800000>;
- samsung,mfc-l = <0x51000000 0x800000>;
- status = "okay";
- };
-
- serial at 13800000 {
- status = "okay";
- };
-
- serial at 13810000 {
- status = "okay";
- };
-
- serial at 13820000 {
- status = "okay";
- };
-
- serial at 13830000 {
- status = "okay";
- };
-
- i2c at 13860000 {
- status = "okay";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <20000>;
- pinctrl-0 = <&i2c0_bus>;
- pinctrl-names = "default";
-
- max8997_pmic at 66 {
- compatible = "maxim,max8997-pmic";
- reg = <0x66>;
- interrupt-parent = <&gpx0>;
- interrupts = <4 0>, <3 0>;
-
- max8997,pmic-buck1-dvs-voltage = <1350000>;
- max8997,pmic-buck2-dvs-voltage = <1100000>;
- max8997,pmic-buck5-dvs-voltage = <1200000>;
-
- regulators {
- ldo1_reg: LDO1 {
- regulator-name = "VDD_ABB_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo2_reg: LDO2 {
- regulator-name = "VDD_ALIVE_1.1V";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- ldo3_reg: LDO3 {
- regulator-name = "VMIPI_1.1V";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- };
-
- ldo4_reg: LDO4 {
- regulator-name = "VDD_RTC_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo6_reg: LDO6 {
- regulator-name = "VMIPI_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo7_reg: LDO7 {
- regulator-name = "VDD_AUD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo8_reg: LDO8 {
- regulator-name = "VADC_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo9_reg: LDO9 {
- regulator-name = "DVDD_SWB_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- ldo10_reg: LDO10 {
- regulator-name = "VDD_PLL_1.1V";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- ldo11_reg: LDO11 {
- regulator-name = "VDD_AUD_3V";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- ldo14_reg: LDO14 {
- regulator-name = "AVDD18_SWB_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo17_reg: LDO17 {
- regulator-name = "VDD_SWB_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- ldo21_reg: LDO21 {
- regulator-name = "VDD_MIF_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- buck1_reg: BUCK1 {
- /*
- * HACK: The real name is VDD_ARM_1.2V,
- * but exynos-cpufreq does not support
- * DT-based regulator lookup yet.
- */
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <950000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "VDD_INT_1.1V";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck3_reg: BUCK3 {
- regulator-name = "VDD_G3D_1.1V";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1100000>;
- };
-
- buck5_reg: BUCK5 {
- regulator-name = "VDDQ_M1M2_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- buck7_reg: BUCK7 {
- regulator-name = "VDD_LCD_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
- };
- };
- };
-
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
@@ -314,12 +111,6 @@
};
};
- fimd at 11c00000 {
- pinctrl-0 = <&lcd_en &lcd_clk &lcd_data24 &pwm0_out>;
- pinctrl-names = "default";
- status = "okay";
- };
-
display-timings {
native-mode = <&timing0>;
timing0: timing {
@@ -335,3 +126,212 @@
};
};
};
+
+&fimd {
+ pinctrl-0 = <&lcd_en &lcd_clk &lcd_data24 &pwm0_out>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&g2d {
+ status = "okay";
+};
+
+&i2c_0 {
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <20000>;
+ pinctrl-0 = <&i2c0_bus>;
+ pinctrl-names = "default";
+
+ max8997_pmic at 66 {
+ compatible = "maxim,max8997-pmic";
+ reg = <0x66>;
+ interrupt-parent = <&gpx0>;
+ interrupts = <4 0>, <3 0>;
+
+ max8997,pmic-buck1-dvs-voltage = <1350000>;
+ max8997,pmic-buck2-dvs-voltage = <1100000>;
+ max8997,pmic-buck5-dvs-voltage = <1200000>;
+
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ABB_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VDD_ALIVE_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VMIPI_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VDD_RTC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VMIPI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD_AUD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VADC_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "DVDD_SWB_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "VDD_PLL_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD_AUD_3V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "AVDD18_SWB_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "VDD_SWB_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo21_reg: LDO21 {
+ regulator-name = "VDD_MIF_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ buck1_reg: BUCK1 {
+ /*
+ * HACK: The real name is VDD_ARM_1.2V,
+ * but exynos-cpufreq does not support
+ * DT-based regulator lookup yet.
+ */
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "VDD_INT_1.1V";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "VDD_G3D_1.1V";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "VDDQ_M1M2_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "VDD_LCD_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&mfc {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+ status = "okay";
+};
+
+&sdhci_0 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_cd>;
+ pinctrl-names = "default";
+ vmmc-supply = <&mmc_reg>;
+ status = "okay";
+};
+
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
+ pinctrl-names = "default";
+ vmmc-supply = <&mmc_reg>;
+ status = "okay";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&tmu {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v4 03/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Origen
2015-05-11 13:42 ` [PATCH v4 03/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Origen Krzysztof Kozlowski
@ 2015-05-13 9:11 ` Kukjin Kim
2015-05-13 9:55 ` Krzysztof Kozlowski
0 siblings, 1 reply; 21+ messages in thread
From: Kukjin Kim @ 2015-05-13 9:11 UTC (permalink / raw)
To: linux-arm-kernel
On 05/11/15 22:42, Krzysztof Kozlowski wrote:
> Usage of labels instead of full paths reduces possible mistakes when
> overriding nodes.
>
In case of this changes, I have no objection.
But I can't see the 'codec' node you deleted in this patch?
And if possible, can you please put the labels in alphabetically when
you create this patch again? so that we could find the labels easily...
- Kukjin
> Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
> ---
> arch/arm/boot/dts/exynos4210-origen.dts | 418 ++++++++++++++++----------------
> 1 file changed, 209 insertions(+), 209 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts
> index b81146141402..e0abfc3324d1 100644
> --- a/arch/arm/boot/dts/exynos4210-origen.dts
> +++ b/arch/arm/boot/dts/exynos4210-origen.dts
> @@ -50,209 +50,6 @@
> };
> };
>
> - watchdog at 10060000 {
> - status = "okay";
> - };
> -
> - rtc at 10070000 {
> - status = "okay";
> - };
> -
> - tmu at 100C0000 {
> - status = "okay";
> - };
> -
> - sdhci at 12530000 {
> - bus-width = <4>;
> - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
> - pinctrl-names = "default";
> - vmmc-supply = <&mmc_reg>;
> - status = "okay";
> - };
> -
> - sdhci at 12510000 {
> - bus-width = <4>;
> - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_cd>;
> - pinctrl-names = "default";
> - vmmc-supply = <&mmc_reg>;
> - status = "okay";
> - };
> -
> - g2d at 12800000 {
> - status = "okay";
> - };
> -
> - codec at 13400000 {
> - samsung,mfc-r = <0x43000000 0x800000>;
> - samsung,mfc-l = <0x51000000 0x800000>;
> - status = "okay";
> - };
> -
> - serial at 13800000 {
> - status = "okay";
> - };
> -
> - serial at 13810000 {
> - status = "okay";
> - };
> -
> - serial at 13820000 {
> - status = "okay";
> - };
> -
> - serial at 13830000 {
> - status = "okay";
> - };
> -
> - i2c at 13860000 {
> - status = "okay";
> - samsung,i2c-sda-delay = <100>;
> - samsung,i2c-max-bus-freq = <20000>;
> - pinctrl-0 = <&i2c0_bus>;
> - pinctrl-names = "default";
> -
> - max8997_pmic at 66 {
> - compatible = "maxim,max8997-pmic";
> - reg = <0x66>;
> - interrupt-parent = <&gpx0>;
> - interrupts = <4 0>, <3 0>;
> -
> - max8997,pmic-buck1-dvs-voltage = <1350000>;
> - max8997,pmic-buck2-dvs-voltage = <1100000>;
> - max8997,pmic-buck5-dvs-voltage = <1200000>;
> -
> - regulators {
> - ldo1_reg: LDO1 {
> - regulator-name = "VDD_ABB_3.3V";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - };
> -
> - ldo2_reg: LDO2 {
> - regulator-name = "VDD_ALIVE_1.1V";
> - regulator-min-microvolt = <1100000>;
> - regulator-max-microvolt = <1100000>;
> - regulator-always-on;
> - };
> -
> - ldo3_reg: LDO3 {
> - regulator-name = "VMIPI_1.1V";
> - regulator-min-microvolt = <1100000>;
> - regulator-max-microvolt = <1100000>;
> - };
> -
> - ldo4_reg: LDO4 {
> - regulator-name = "VDD_RTC_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - };
> -
> - ldo6_reg: LDO6 {
> - regulator-name = "VMIPI_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - };
> -
> - ldo7_reg: LDO7 {
> - regulator-name = "VDD_AUD_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - };
> -
> - ldo8_reg: LDO8 {
> - regulator-name = "VADC_3.3V";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - };
> -
> - ldo9_reg: LDO9 {
> - regulator-name = "DVDD_SWB_2.8V";
> - regulator-min-microvolt = <2800000>;
> - regulator-max-microvolt = <2800000>;
> - regulator-always-on;
> - };
> -
> - ldo10_reg: LDO10 {
> - regulator-name = "VDD_PLL_1.1V";
> - regulator-min-microvolt = <1100000>;
> - regulator-max-microvolt = <1100000>;
> - regulator-always-on;
> - };
> -
> - ldo11_reg: LDO11 {
> - regulator-name = "VDD_AUD_3V";
> - regulator-min-microvolt = <3000000>;
> - regulator-max-microvolt = <3000000>;
> - };
> -
> - ldo14_reg: LDO14 {
> - regulator-name = "AVDD18_SWB_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - };
> -
> - ldo17_reg: LDO17 {
> - regulator-name = "VDD_SWB_3.3V";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - };
> -
> - ldo21_reg: LDO21 {
> - regulator-name = "VDD_MIF_1.2V";
> - regulator-min-microvolt = <1200000>;
> - regulator-max-microvolt = <1200000>;
> - regulator-always-on;
> - };
> -
> - buck1_reg: BUCK1 {
> - /*
> - * HACK: The real name is VDD_ARM_1.2V,
> - * but exynos-cpufreq does not support
> - * DT-based regulator lookup yet.
> - */
> - regulator-name = "vdd_arm";
> - regulator-min-microvolt = <950000>;
> - regulator-max-microvolt = <1350000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> -
> - buck2_reg: BUCK2 {
> - regulator-name = "VDD_INT_1.1V";
> - regulator-min-microvolt = <900000>;
> - regulator-max-microvolt = <1100000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> -
> - buck3_reg: BUCK3 {
> - regulator-name = "VDD_G3D_1.1V";
> - regulator-min-microvolt = <900000>;
> - regulator-max-microvolt = <1100000>;
> - };
> -
> - buck5_reg: BUCK5 {
> - regulator-name = "VDDQ_M1M2_1.2V";
> - regulator-min-microvolt = <1200000>;
> - regulator-max-microvolt = <1200000>;
> - regulator-always-on;
> - };
> -
> - buck7_reg: BUCK7 {
> - regulator-name = "VDD_LCD_3.3V";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> - };
> - };
> - };
> -
> gpio_keys {
> compatible = "gpio-keys";
> #address-cells = <1>;
> @@ -314,12 +111,6 @@
> };
> };
>
> - fimd at 11c00000 {
> - pinctrl-0 = <&lcd_en &lcd_clk &lcd_data24 &pwm0_out>;
> - pinctrl-names = "default";
> - status = "okay";
> - };
> -
> display-timings {
> native-mode = <&timing0>;
> timing0: timing {
> @@ -335,3 +126,212 @@
> };
> };
> };
> +
> +&fimd {
> + pinctrl-0 = <&lcd_en &lcd_clk &lcd_data24 &pwm0_out>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&g2d {
> + status = "okay";
> +};
> +
> +&i2c_0 {
> + status = "okay";
> + samsung,i2c-sda-delay = <100>;
> + samsung,i2c-max-bus-freq = <20000>;
> + pinctrl-0 = <&i2c0_bus>;
> + pinctrl-names = "default";
> +
> + max8997_pmic at 66 {
> + compatible = "maxim,max8997-pmic";
> + reg = <0x66>;
> + interrupt-parent = <&gpx0>;
> + interrupts = <4 0>, <3 0>;
> +
> + max8997,pmic-buck1-dvs-voltage = <1350000>;
> + max8997,pmic-buck2-dvs-voltage = <1100000>;
> + max8997,pmic-buck5-dvs-voltage = <1200000>;
> +
> + regulators {
> + ldo1_reg: LDO1 {
> + regulator-name = "VDD_ABB_3.3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo2_reg: LDO2 {
> + regulator-name = "VDD_ALIVE_1.1V";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + };
> +
> + ldo3_reg: LDO3 {
> + regulator-name = "VMIPI_1.1V";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + };
> +
> + ldo4_reg: LDO4 {
> + regulator-name = "VDD_RTC_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + ldo6_reg: LDO6 {
> + regulator-name = "VMIPI_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + ldo7_reg: LDO7 {
> + regulator-name = "VDD_AUD_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + ldo8_reg: LDO8 {
> + regulator-name = "VADC_3.3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo9_reg: LDO9 {
> + regulator-name = "DVDD_SWB_2.8V";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-always-on;
> + };
> +
> + ldo10_reg: LDO10 {
> + regulator-name = "VDD_PLL_1.1V";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + };
> +
> + ldo11_reg: LDO11 {
> + regulator-name = "VDD_AUD_3V";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + };
> +
> + ldo14_reg: LDO14 {
> + regulator-name = "AVDD18_SWB_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + ldo17_reg: LDO17 {
> + regulator-name = "VDD_SWB_3.3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + ldo21_reg: LDO21 {
> + regulator-name = "VDD_MIF_1.2V";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + };
> +
> + buck1_reg: BUCK1 {
> + /*
> + * HACK: The real name is VDD_ARM_1.2V,
> + * but exynos-cpufreq does not support
> + * DT-based regulator lookup yet.
> + */
> + regulator-name = "vdd_arm";
> + regulator-min-microvolt = <950000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + buck2_reg: BUCK2 {
> + regulator-name = "VDD_INT_1.1V";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + buck3_reg: BUCK3 {
> + regulator-name = "VDD_G3D_1.1V";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1100000>;
> + };
> +
> + buck5_reg: BUCK5 {
> + regulator-name = "VDDQ_M1M2_1.2V";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + };
> +
> + buck7_reg: BUCK7 {
> + regulator-name = "VDD_LCD_3.3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&mfc {
> + samsung,mfc-r = <0x43000000 0x800000>;
> + samsung,mfc-l = <0x51000000 0x800000>;
> + status = "okay";
> +};
> +
> +&sdhci_0 {
> + bus-width = <4>;
> + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_cd>;
> + pinctrl-names = "default";
> + vmmc-supply = <&mmc_reg>;
> + status = "okay";
> +};
> +
> +&sdhci_2 {
> + bus-width = <4>;
> + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
> + pinctrl-names = "default";
> + vmmc-supply = <&mmc_reg>;
> + status = "okay";
> +};
> +
> +&serial_0 {
> + status = "okay";
> +};
> +
> +&serial_1 {
> + status = "okay";
> +};
> +
> +&serial_2 {
> + status = "okay";
> +};
> +
> +&serial_3 {
> + status = "okay";
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> +
> +&tmu {
> + status = "okay";
> +};
> +
> +&watchdog {
> + status = "okay";
> +};
^ permalink raw reply [flat|nested] 21+ messages in thread* [PATCH v4 03/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Origen
2015-05-13 9:11 ` Kukjin Kim
@ 2015-05-13 9:55 ` Krzysztof Kozlowski
0 siblings, 0 replies; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-13 9:55 UTC (permalink / raw)
To: linux-arm-kernel
W dniu 13.05.2015 o 18:11, Kukjin Kim pisze:
> On 05/11/15 22:42, Krzysztof Kozlowski wrote:
>> Usage of labels instead of full paths reduces possible mistakes when
>> overriding nodes.
>>
>
> In case of this changes, I have no objection.
> But I can't see the 'codec' node you deleted in this patch?
It is under label "mfc". This label was already defined in exynos4.dtsi
before:
>> +&mfc {
>> + samsung,mfc-r = <0x43000000 0x800000>;
>> + samsung,mfc-l = <0x51000000 0x800000>;
>> + status = "okay";
>> +};
>
> And if possible, can you please put the labels in alphabetically when
> you create this patch again? so that we could find the labels easily...
Yes, when I switched to the "label convention" I put them in
alphabetical order. However I did not re-order other (existing) nodes.
This makes some confusion but I wanted to limit the scope of this change
and do only one thing - switch to "label convention".
Do you want me to reorder alphabetically everything?
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH v4 04/13] ARM: dts: exynos4: Use labels for overriding nodes in SMDKv310
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (2 preceding siblings ...)
2015-05-11 13:42 ` [PATCH v4 03/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4210 Origen Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
2015-05-11 13:42 ` [PATCH v4 05/13] ARM: dts: exynos4: Use labels for overriding nodes in Trats Krzysztof Kozlowski
` (8 subsequent siblings)
12 siblings, 0 replies; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4210-smdkv310.dts | 280 +++++++++++++++---------------
1 file changed, 140 insertions(+), 140 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4210-smdkv310.dts b/arch/arm/boot/dts/exynos4210-smdkv310.dts
index 86216fff1b4f..043b03caff8f 100644
--- a/arch/arm/boot/dts/exynos4210-smdkv310.dts
+++ b/arch/arm/boot/dts/exynos4210-smdkv310.dts
@@ -30,181 +30,181 @@
stdout-path = &serial_1;
};
- sdhci at 12530000 {
- bus-width = <4>;
- pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
- status = "okay";
- };
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <12000000>;
+ };
- g2d at 12800000 {
- status = "okay";
+ xusbxti {
+ compatible = "samsung,clock-xusbxti";
+ clock-frequency = <24000000>;
+ };
};
+};
- codec at 13400000 {
- samsung,mfc-r = <0x43000000 0x800000>;
- samsung,mfc-l = <0x51000000 0x800000>;
- status = "okay";
- };
+&g2d {
+ status = "okay";
+};
- serial at 13800000 {
- status = "okay";
- };
+&i2c_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <100000>;
+ status = "okay";
- serial at 13810000 {
- status = "okay";
+ eeprom at 50 {
+ compatible = "samsung,24ad0xd1";
+ reg = <0x50>;
};
- serial at 13820000 {
- status = "okay";
+ eeprom at 52 {
+ compatible = "samsung,24ad0xd1";
+ reg = <0x52>;
};
+};
- serial at 13830000 {
- status = "okay";
+&keypad {
+ samsung,keypad-num-rows = <2>;
+ samsung,keypad-num-columns = <8>;
+ linux,keypad-no-autorepeat;
+ linux,keypad-wakeup;
+ pinctrl-names = "default";
+ pinctrl-0 = <&keypad_rows &keypad_cols>;
+ status = "okay";
+
+ key_1 {
+ keypad,row = <0>;
+ keypad,column = <3>;
+ linux,code = <2>;
};
- pinctrl at 11000000 {
- keypad_rows: keypad-rows {
- samsung,pins = "gpx2-0", "gpx2-1";
- samsung,pin-function = <3>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
- };
-
- keypad_cols: keypad-cols {
- samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
- "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
- samsung,pin-function = <3>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
+ key_2 {
+ keypad,row = <0>;
+ keypad,column = <4>;
+ linux,code = <3>;
};
- keypad at 100A0000 {
- samsung,keypad-num-rows = <2>;
- samsung,keypad-num-columns = <8>;
- linux,keypad-no-autorepeat;
- linux,keypad-wakeup;
- pinctrl-names = "default";
- pinctrl-0 = <&keypad_rows &keypad_cols>;
- status = "okay";
+ key_3 {
+ keypad,row = <0>;
+ keypad,column = <5>;
+ linux,code = <4>;
+ };
- key_1 {
- keypad,row = <0>;
- keypad,column = <3>;
- linux,code = <2>;
- };
+ key_4 {
+ keypad,row = <0>;
+ keypad,column = <6>;
+ linux,code = <5>;
+ };
- key_2 {
- keypad,row = <0>;
- keypad,column = <4>;
- linux,code = <3>;
- };
+ key_5 {
+ keypad,row = <0>;
+ keypad,column = <7>;
+ linux,code = <6>;
+ };
- key_3 {
- keypad,row = <0>;
- keypad,column = <5>;
- linux,code = <4>;
- };
+ key_a {
+ keypad,row = <1>;
+ keypad,column = <3>;
+ linux,code = <30>;
+ };
- key_4 {
- keypad,row = <0>;
- keypad,column = <6>;
- linux,code = <5>;
- };
+ key_b {
+ keypad,row = <1>;
+ keypad,column = <4>;
+ linux,code = <48>;
+ };
- key_5 {
- keypad,row = <0>;
- keypad,column = <7>;
- linux,code = <6>;
- };
+ key_c {
+ keypad,row = <1>;
+ keypad,column = <5>;
+ linux,code = <46>;
+ };
- key_a {
- keypad,row = <1>;
- keypad,column = <3>;
- linux,code = <30>;
- };
+ key_d {
+ keypad,row = <1>;
+ keypad,column = <6>;
+ linux,code = <32>;
+ };
- key_b {
- keypad,row = <1>;
- keypad,column = <4>;
- linux,code = <48>;
- };
+ key_e {
+ keypad,row = <1>;
+ keypad,column = <7>;
+ linux,code = <18>;
+ };
+};
- key_c {
- keypad,row = <1>;
- keypad,column = <5>;
- linux,code = <46>;
- };
+&mfc {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+ status = "okay";
+};
- key_d {
- keypad,row = <1>;
- keypad,column = <6>;
- linux,code = <32>;
- };
+&pinctrl_1 {
+ keypad_rows: keypad-rows {
+ samsung,pins = "gpx2-0", "gpx2-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
- key_e {
- keypad,row = <1>;
- keypad,column = <7>;
- linux,code = <18>;
- };
+ keypad_cols: keypad-cols {
+ samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
+ "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
};
+};
- i2c at 13860000 {
- #address-cells = <1>;
- #size-cells = <0>;
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <100000>;
- status = "okay";
-
- eeprom at 50 {
- compatible = "samsung,24ad0xd1";
- reg = <0x50>;
- };
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+ status = "okay";
+};
- eeprom at 52 {
- compatible = "samsung,24ad0xd1";
- reg = <0x52>;
- };
- };
+&serial_0 {
+ status = "okay";
+};
- spi_2: spi at 13940000 {
- cs-gpios = <&gpc1 2 0>;
- status = "okay";
+&serial_1 {
+ status = "okay";
+};
- w25x80 at 0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "w25x80";
- reg = <0>;
- spi-max-frequency = <1000000>;
+&serial_2 {
+ status = "okay";
+};
- controller-data {
- samsung,spi-feedback-delay = <0>;
- };
+&serial_3 {
+ status = "okay";
+};
- partition at 0 {
- label = "U-Boot";
- reg = <0x0 0x40000>;
- read-only;
- };
+&spi_2 {
+ cs-gpios = <&gpc1 2 0>;
+ status = "okay";
- partition at 40000 {
- label = "Kernel";
- reg = <0x40000 0xc0000>;
- };
+ w25x80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "w25x80";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+
+ controller-data {
+ samsung,spi-feedback-delay = <0>;
};
- };
- fixed-rate-clocks {
- xxti {
- compatible = "samsung,clock-xxti";
- clock-frequency = <12000000>;
+ partition at 0 {
+ label = "U-Boot";
+ reg = <0x0 0x40000>;
+ read-only;
};
- xusbxti {
- compatible = "samsung,clock-xusbxti";
- clock-frequency = <24000000>;
+ partition at 40000 {
+ label = "Kernel";
+ reg = <0x40000 0xc0000>;
};
};
};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v4 05/13] ARM: dts: exynos4: Use labels for overriding nodes in Trats
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (3 preceding siblings ...)
2015-05-11 13:42 ` [PATCH v4 04/13] ARM: dts: exynos4: Use labels for overriding nodes in SMDKv310 Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
2015-05-11 13:42 ` [PATCH v4 06/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4212 Krzysztof Kozlowski
` (7 subsequent siblings)
12 siblings, 0 replies; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4210-trats.dts | 592 ++++++++++++++++-----------------
1 file changed, 296 insertions(+), 296 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts
index 32c5fd8f6269..98f3ce65cb9a 100644
--- a/arch/arm/boot/dts/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/exynos4210-trats.dts
@@ -89,42 +89,6 @@
};
};
- hsotg at 12480000 {
- vusb_d-supply = <&vusb_reg>;
- vusb_a-supply = <&vusbdac_reg>;
- dr_mode = "peripheral";
- status = "okay";
- };
-
- sdhci_emmc: sdhci at 12510000 {
- bus-width = <8>;
- non-removable;
- pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
- pinctrl-names = "default";
- vmmc-supply = <&vemmc_reg>;
- status = "okay";
- };
-
- exynos-usbphy at 125B0000 {
- status = "okay";
- };
-
- serial at 13800000 {
- status = "okay";
- };
-
- serial at 13810000 {
- status = "okay";
- };
-
- serial at 13820000 {
- status = "okay";
- };
-
- serial at 13830000 {
- status = "okay";
- };
-
gpio-keys {
compatible = "gpio-keys";
@@ -158,201 +122,6 @@
};
};
- i2c at 13890000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <400000>;
- pinctrl-0 = <&i2c3_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- mms114-touchscreen at 48 {
- compatible = "melfas,mms114";
- reg = <0x48>;
- interrupt-parent = <&gpx0>;
- interrupts = <4 2>;
- x-size = <720>;
- y-size = <1280>;
- avdd-supply = <&tsp_reg>;
- vdd-supply = <&tsp_reg>;
- };
- };
-
- i2c at 138B0000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <100000>;
- pinctrl-0 = <&i2c5_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- max8997_pmic at 66 {
- compatible = "maxim,max8997-pmic";
-
- reg = <0x66>;
-
- max8997,pmic-buck1-uses-gpio-dvs;
- max8997,pmic-buck2-uses-gpio-dvs;
- max8997,pmic-buck5-uses-gpio-dvs;
-
- max8997,pmic-ignore-gpiodvs-side-effect;
- max8997,pmic-buck125-default-dvs-idx = <0>;
-
- max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>,
- <&gpx0 6 0>,
- <&gpl0 0 0>;
-
- max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
- <1250000>, <1200000>,
- <1150000>, <1100000>,
- <1000000>, <950000>;
-
- max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
- <950000>, <900000>,
- <1100000>, <1000000>,
- <950000>, <900000>;
-
- max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
- <1200000>, <1200000>,
- <1200000>, <1200000>,
- <1200000>, <1200000>;
-
- regulators {
- valive_reg: LDO2 {
- regulator-name = "VALIVE_1.1V_C210";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- vusb_reg: LDO3 {
- regulator-name = "VUSB_1.1V_C210";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- };
-
- vmipi_reg: LDO4 {
- regulator-name = "VMIPI_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vpda_reg: LDO6 {
- regulator-name = "VCC_1.8V_PDA";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- vcam_reg: LDO7 {
- regulator-name = "CAM_ISP_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vusbdac_reg: LDO8 {
- regulator-name = "VUSB/VDAC_3.3V_C210";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- vccpda_reg: LDO9 {
- regulator-name = "VCC_2.8V_PDA";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- vpll_reg: LDO10 {
- regulator-name = "VPLL_1.1V_C210";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- vtcam_reg: LDO12 {
- regulator-name = "VT_CAM_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vcclcd_reg: LDO13 {
- regulator-name = "VCC_3.3V_LCD";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- vlcd_reg: LDO15 {
- regulator-name = "VLCD_2.2V";
- regulator-min-microvolt = <2200000>;
- regulator-max-microvolt = <2200000>;
- };
-
- camsensor_reg: LDO16 {
- regulator-name = "CAM_SENSOR_IO_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vddq_reg: LDO21 {
- regulator-name = "VDDQ_M1M2_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- varm_breg: BUCK1 {
- /*
- * HACK: The real name is VARM_1.2V_C210,
- * but exynos-cpufreq does not support
- * DT-based regulator lookup yet.
- */
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- };
-
- vint_breg: BUCK2 {
- regulator-name = "VINT_1.1V_C210";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- };
-
- camisp_breg: BUCK4 {
- regulator-name = "CAM_ISP_CORE_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- vmem_breg: BUCK5 {
- regulator-name = "VMEM_1.2V_C210";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- vccsub_breg: BUCK7 {
- regulator-name = "VCC_SUB_2.0V";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
-
- safe1_sreg: ESAFEOUT1 {
- regulator-name = "SAFEOUT1";
- regulator-always-on;
- };
-
- safe2_sreg: ESAFEOUT2 {
- regulator-name = "SAFEOUT2";
- regulator-boot-on;
- };
- };
- };
- };
-
fixed-rate-clocks {
xxti {
compatible = "samsung,clock-xxti";
@@ -365,71 +134,6 @@
};
};
- dsi_0: dsi at 11C80000 {
- vddcore-supply = <&vusb_reg>;
- vddio-supply = <&vmipi_reg>;
- samsung,pll-clock-frequency = <24000000>;
- status = "okay";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 1 {
- reg = <1>;
-
- dsi_out: endpoint {
- remote-endpoint = <&dsi_in>;
- samsung,burst-clock-frequency = <500000000>;
- samsung,esc-clock-frequency = <20000000>;
- };
- };
- };
-
- panel at 0 {
- reg = <0>;
- compatible = "samsung,s6e8aa0";
- vdd3-supply = <&vcclcd_reg>;
- vci-supply = <&vlcd_reg>;
- reset-gpios = <&gpy4 5 0>;
- power-on-delay= <50>;
- reset-delay = <100>;
- init-delay = <100>;
- flip-horizontal;
- flip-vertical;
- panel-width-mm = <58>;
- panel-height-mm = <103>;
-
- display-timings {
- timing-0 {
- clock-frequency = <57153600>;
- hactive = <720>;
- vactive = <1280>;
- hfront-porch = <5>;
- hback-porch = <5>;
- hsync-len = <5>;
- vfront-porch = <13>;
- vback-porch = <1>;
- vsync-len = <2>;
- };
- };
-
- port {
- dsi_in: endpoint {
- remote-endpoint = <&dsi_out>;
- };
- };
- };
- };
-
- fimd at 11c00000 {
- status = "okay";
- };
-
- tmu at 100C0000 {
- status = "okay";
- };
-
thermal-zones {
cpu_thermal: cpu-thermal {
cooling-maps {
@@ -483,3 +187,299 @@
};
};
};
+
+&dsi_0 {
+ vddcore-supply = <&vusb_reg>;
+ vddio-supply = <&vmipi_reg>;
+ samsung,pll-clock-frequency = <24000000>;
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 1 {
+ reg = <1>;
+
+ dsi_out: endpoint {
+ remote-endpoint = <&dsi_in>;
+ samsung,burst-clock-frequency = <500000000>;
+ samsung,esc-clock-frequency = <20000000>;
+ };
+ };
+ };
+
+ panel at 0 {
+ reg = <0>;
+ compatible = "samsung,s6e8aa0";
+ vdd3-supply = <&vcclcd_reg>;
+ vci-supply = <&vlcd_reg>;
+ reset-gpios = <&gpy4 5 0>;
+ power-on-delay= <50>;
+ reset-delay = <100>;
+ init-delay = <100>;
+ flip-horizontal;
+ flip-vertical;
+ panel-width-mm = <58>;
+ panel-height-mm = <103>;
+
+ display-timings {
+ timing-0 {
+ clock-frequency = <57153600>;
+ hactive = <720>;
+ vactive = <1280>;
+ hfront-porch = <5>;
+ hback-porch = <5>;
+ hsync-len = <5>;
+ vfront-porch = <13>;
+ vback-porch = <1>;
+ vsync-len = <2>;
+ };
+ };
+
+ port {
+ dsi_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+ };
+};
+
+&exynos_usbphy {
+ status = "okay";
+};
+
+&fimd {
+ status = "okay";
+};
+
+&hsotg {
+ vusb_d-supply = <&vusb_reg>;
+ vusb_a-supply = <&vusbdac_reg>;
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&i2c_3 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <400000>;
+ pinctrl-0 = <&i2c3_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ mms114-touchscreen at 48 {
+ compatible = "melfas,mms114";
+ reg = <0x48>;
+ interrupt-parent = <&gpx0>;
+ interrupts = <4 2>;
+ x-size = <720>;
+ y-size = <1280>;
+ avdd-supply = <&tsp_reg>;
+ vdd-supply = <&tsp_reg>;
+ };
+};
+
+&i2c_5 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <100000>;
+ pinctrl-0 = <&i2c5_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ max8997_pmic at 66 {
+ compatible = "maxim,max8997-pmic";
+
+ reg = <0x66>;
+
+ max8997,pmic-buck1-uses-gpio-dvs;
+ max8997,pmic-buck2-uses-gpio-dvs;
+ max8997,pmic-buck5-uses-gpio-dvs;
+
+ max8997,pmic-ignore-gpiodvs-side-effect;
+ max8997,pmic-buck125-default-dvs-idx = <0>;
+
+ max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>,
+ <&gpx0 6 0>,
+ <&gpl0 0 0>;
+
+ max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
+ <1250000>, <1200000>,
+ <1150000>, <1100000>,
+ <1000000>, <950000>;
+
+ max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
+ <950000>, <900000>,
+ <1100000>, <1000000>,
+ <950000>, <900000>;
+
+ max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>;
+
+ regulators {
+ valive_reg: LDO2 {
+ regulator-name = "VALIVE_1.1V_C210";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ vusb_reg: LDO3 {
+ regulator-name = "VUSB_1.1V_C210";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ vmipi_reg: LDO4 {
+ regulator-name = "VMIPI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vpda_reg: LDO6 {
+ regulator-name = "VCC_1.8V_PDA";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vcam_reg: LDO7 {
+ regulator-name = "CAM_ISP_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vusbdac_reg: LDO8 {
+ regulator-name = "VUSB/VDAC_3.3V_C210";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vccpda_reg: LDO9 {
+ regulator-name = "VCC_2.8V_PDA";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ vpll_reg: LDO10 {
+ regulator-name = "VPLL_1.1V_C210";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ vtcam_reg: LDO12 {
+ regulator-name = "VT_CAM_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vcclcd_reg: LDO13 {
+ regulator-name = "VCC_3.3V_LCD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vlcd_reg: LDO15 {
+ regulator-name = "VLCD_2.2V";
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ };
+
+ camsensor_reg: LDO16 {
+ regulator-name = "CAM_SENSOR_IO_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddq_reg: LDO21 {
+ regulator-name = "VDDQ_M1M2_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ varm_breg: BUCK1 {
+ /*
+ * HACK: The real name is VARM_1.2V_C210,
+ * but exynos-cpufreq does not support
+ * DT-based regulator lookup yet.
+ */
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ };
+
+ vint_breg: BUCK2 {
+ regulator-name = "VINT_1.1V_C210";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ camisp_breg: BUCK4 {
+ regulator-name = "CAM_ISP_CORE_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vmem_breg: BUCK5 {
+ regulator-name = "VMEM_1.2V_C210";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ vccsub_breg: BUCK7 {
+ regulator-name = "VCC_SUB_2.0V";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ safe1_sreg: ESAFEOUT1 {
+ regulator-name = "SAFEOUT1";
+ regulator-always-on;
+ };
+
+ safe2_sreg: ESAFEOUT2 {
+ regulator-name = "SAFEOUT2";
+ regulator-boot-on;
+ };
+ };
+ };
+};
+
+&sdhci_0 {
+ bus-width = <8>;
+ non-removable;
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
+ pinctrl-names = "default";
+ vmmc-supply = <&vemmc_reg>;
+ status = "okay";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
+
+&tmu {
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v4 06/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4212
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (4 preceding siblings ...)
2015-05-11 13:42 ` [PATCH v4 05/13] ARM: dts: exynos4: Use labels for overriding nodes in Trats Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
2015-05-11 13:42 ` [PATCH v4 07/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4x12 Krzysztof Kozlowski
` (6 subsequent siblings)
12 siblings, 0 replies; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4212.dtsi | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4212.dtsi b/arch/arm/boot/dts/exynos4212.dtsi
index 5be03288f1ee..d9c8efeef208 100644
--- a/arch/arm/boot/dts/exynos4212.dtsi
+++ b/arch/arm/boot/dts/exynos4212.dtsi
@@ -41,12 +41,12 @@
reg = <0xA01>;
};
};
+};
- combiner: interrupt-controller at 10440000 {
- samsung,combiner-nr = <18>;
- };
+&combiner {
+ samsung,combiner-nr = <18>;
+};
- gic: interrupt-controller at 10490000 {
- cpu-offset = <0x8000>;
- };
+&gic {
+ cpu-offset = <0x8000>;
};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v4 07/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4x12
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (5 preceding siblings ...)
2015-05-11 13:42 ` [PATCH v4 06/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4212 Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
2015-05-11 13:42 ` [PATCH v4 08/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4412 Krzysztof Kozlowski
` (5 subsequent siblings)
12 siblings, 0 replies; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4x12.dtsi | 216 +++++++++++++++++++-------------------
1 file changed, 108 insertions(+), 108 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi
index 8cd27641cfb7..802116eed11b 100644
--- a/arch/arm/boot/dts/exynos4x12.dtsi
+++ b/arch/arm/boot/dts/exynos4x12.dtsi
@@ -96,32 +96,6 @@
};
};
- combiner: interrupt-controller at 10440000 {
- interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
- <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
- <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
- <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
- <0 107 0>, <0 108 0>, <0 48 0>, <0 42 0>;
- };
-
- pinctrl_0: pinctrl at 11400000 {
- compatible = "samsung,exynos4x12-pinctrl";
- reg = <0x11400000 0x1000>;
- interrupts = <0 47 0>;
- };
-
- pinctrl_1: pinctrl at 11000000 {
- compatible = "samsung,exynos4x12-pinctrl";
- reg = <0x11000000 0x1000>;
- interrupts = <0 46 0>;
-
- wakup_eint: wakeup-interrupt-controller {
- compatible = "samsung,exynos4210-wakeup-eint";
- interrupt-parent = <&gic>;
- interrupts = <0 32 0>;
- };
- };
-
adc: adc at 126C0000 {
compatible = "samsung,exynos-adc-v1";
reg = <0x126C0000 0x100>;
@@ -135,30 +109,6 @@
status = "disabled";
};
- pinctrl_2: pinctrl at 03860000 {
- compatible = "samsung,exynos4x12-pinctrl";
- reg = <0x03860000 0x1000>;
- interrupt-parent = <&combiner>;
- interrupts = <10 0>;
- };
-
- pinctrl_3: pinctrl at 106E0000 {
- compatible = "samsung,exynos4x12-pinctrl";
- reg = <0x106E0000 0x1000>;
- interrupts = <0 72 0>;
- };
-
- pmu_system_controller: system-controller at 10020000 {
- compatible = "samsung,exynos4212-pmu", "syscon";
- clock-names = "clkout0", "clkout1", "clkout2", "clkout3",
- "clkout4", "clkout8", "clkout9";
- clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>,
- <&clock CLK_OUT_LEFTBUS>, <&clock CLK_OUT_RIGHTBUS>,
- <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>,
- <&clock CLK_XUSBXTI>;
- #clock-cells = <1>;
- };
-
g2d: g2d at 10800000 {
compatible = "samsung,exynos4212-g2d";
reg = <0x10800000 0x1000>;
@@ -173,40 +123,7 @@
<&clock CLK_PIXELASYNCM0>, <&clock CLK_PIXELASYNCM1>;
clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1";
- fimc_0: fimc at 11800000 {
- compatible = "samsung,exynos4212-fimc";
- samsung,pix-limits = <4224 8192 1920 4224>;
- samsung,mainscaler-ext;
- samsung,isp-wb;
- samsung,cam-if;
- };
-
- fimc_1: fimc at 11810000 {
- compatible = "samsung,exynos4212-fimc";
- samsung,pix-limits = <4224 8192 1920 4224>;
- samsung,mainscaler-ext;
- samsung,isp-wb;
- samsung,cam-if;
- };
-
- fimc_2: fimc at 11820000 {
- compatible = "samsung,exynos4212-fimc";
- samsung,pix-limits = <4224 8192 1920 4224>;
- samsung,mainscaler-ext;
- samsung,isp-wb;
- samsung,lcd-wb;
- samsung,cam-if;
- };
-
- fimc_3: fimc at 11830000 {
- compatible = "samsung,exynos4212-fimc";
- samsung,pix-limits = <1920 8192 1366 1920>;
- samsung,rotators = <0>;
- samsung,mainscaler-ext;
- samsung,isp-wb;
- samsung,lcd-wb;
- };
-
+ /* fimc_[0-3] are configured outside, under phandles */
fimc_lite_0: fimc-lite at 12390000 {
compatible = "samsung,exynos4212-fimc-lite";
reg = <0x12390000 0x1000>;
@@ -283,34 +200,117 @@
clock-names = "biu", "ciu";
status = "disabled";
};
+};
- exynos-usbphy at 125B0000 {
- compatible = "samsung,exynos4x12-usb2-phy";
- samsung,sysreg-phandle = <&sys_reg>;
- };
+&combiner {
+ interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+ <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+ <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+ <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
+ <0 107 0>, <0 108 0>, <0 48 0>, <0 42 0>;
+};
- tmu at 100C0000 {
- compatible = "samsung,exynos4412-tmu";
- interrupt-parent = <&combiner>;
- interrupts = <2 4>;
- reg = <0x100C0000 0x100>;
- clocks = <&clock 383>;
- clock-names = "tmu_apbif";
- status = "disabled";
- };
+&exynos_usbphy {
+ compatible = "samsung,exynos4x12-usb2-phy";
+ samsung,sysreg-phandle = <&sys_reg>;
+};
- jpeg-codec at 11840000 {
- compatible = "samsung,exynos4212-jpeg";
- };
+&fimc_0 {
+ compatible = "samsung,exynos4212-fimc";
+ samsung,pix-limits = <4224 8192 1920 4224>;
+ samsung,mainscaler-ext;
+ samsung,isp-wb;
+ samsung,cam-if;
+};
- hdmi: hdmi at 12D00000 {
- compatible = "samsung,exynos4212-hdmi";
- };
+&fimc_1 {
+ compatible = "samsung,exynos4212-fimc";
+ samsung,pix-limits = <4224 8192 1920 4224>;
+ samsung,mainscaler-ext;
+ samsung,isp-wb;
+ samsung,cam-if;
+};
+
+&fimc_2 {
+ compatible = "samsung,exynos4212-fimc";
+ samsung,pix-limits = <4224 8192 1920 4224>;
+ samsung,mainscaler-ext;
+ samsung,isp-wb;
+ samsung,lcd-wb;
+ samsung,cam-if;
+};
+
+&fimc_3 {
+ compatible = "samsung,exynos4212-fimc";
+ samsung,pix-limits = <1920 8192 1366 1920>;
+ samsung,rotators = <0>;
+ samsung,mainscaler-ext;
+ samsung,isp-wb;
+ samsung,lcd-wb;
+};
+
+&hdmi {
+ compatible = "samsung,exynos4212-hdmi";
+};
+
+&jpeg_codec {
+ compatible = "samsung,exynos4212-jpeg";
+};
+
+&mixer {
+ compatible = "samsung,exynos4212-mixer";
+ clock-names = "mixer", "hdmi", "sclk_hdmi", "vp";
+ clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
+ <&clock CLK_SCLK_HDMI>, <&clock CLK_VP>;
+};
- mixer: mixer at 12C10000 {
- compatible = "samsung,exynos4212-mixer";
- clock-names = "mixer", "hdmi", "sclk_hdmi", "vp";
- clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
- <&clock CLK_SCLK_HDMI>, <&clock CLK_VP>;
+&pinctrl_0 {
+ compatible = "samsung,exynos4x12-pinctrl";
+ reg = <0x11400000 0x1000>;
+ interrupts = <0 47 0>;
+};
+
+&pinctrl_1 {
+ compatible = "samsung,exynos4x12-pinctrl";
+ reg = <0x11000000 0x1000>;
+ interrupts = <0 46 0>;
+
+ wakup_eint: wakeup-interrupt-controller {
+ compatible = "samsung,exynos4210-wakeup-eint";
+ interrupt-parent = <&gic>;
+ interrupts = <0 32 0>;
};
};
+
+&pinctrl_2 {
+ compatible = "samsung,exynos4x12-pinctrl";
+ reg = <0x03860000 0x1000>;
+ interrupt-parent = <&combiner>;
+ interrupts = <10 0>;
+};
+
+&pinctrl_3 {
+ compatible = "samsung,exynos4x12-pinctrl";
+ reg = <0x106E0000 0x1000>;
+ interrupts = <0 72 0>;
+};
+
+&pmu_system_controller {
+ compatible = "samsung,exynos4212-pmu", "syscon";
+ clock-names = "clkout0", "clkout1", "clkout2", "clkout3",
+ "clkout4", "clkout8", "clkout9";
+ clocks = <&clock CLK_OUT_DMC>, <&clock CLK_OUT_TOP>,
+ <&clock CLK_OUT_LEFTBUS>, <&clock CLK_OUT_RIGHTBUS>,
+ <&clock CLK_OUT_CPU>, <&clock CLK_XXTI>, <&clock CLK_XUSBXTI>;
+ #clock-cells = <1>;
+};
+
+&tmu {
+ compatible = "samsung,exynos4412-tmu";
+ interrupt-parent = <&combiner>;
+ interrupts = <2 4>;
+ reg = <0x100C0000 0x100>;
+ clocks = <&clock 383>;
+ clock-names = "tmu_apbif";
+ status = "disabled";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v4 08/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4412
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (6 preceding siblings ...)
2015-05-11 13:42 ` [PATCH v4 07/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4x12 Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
2015-05-11 13:42 ` [PATCH v4 09/13] ARM: dts: exynos4: Use labels for overriding nodes in Odroid Krzysztof Kozlowski
` (4 subsequent siblings)
12 siblings, 0 replies; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4412.dtsi | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412.dtsi b/arch/arm/boot/dts/exynos4412.dtsi
index 68ad43b391ae..b78ada70bd05 100644
--- a/arch/arm/boot/dts/exynos4412.dtsi
+++ b/arch/arm/boot/dts/exynos4412.dtsi
@@ -54,19 +54,19 @@
};
};
- combiner: interrupt-controller at 10440000 {
- samsung,combiner-nr = <20>;
- };
-
pmu {
interrupts = <2 2>, <3 2>, <18 2>, <19 2>;
};
+};
- gic: interrupt-controller at 10490000 {
- cpu-offset = <0x4000>;
- };
+&pmu_system_controller {
+ compatible = "samsung,exynos4412-pmu", "syscon";
+};
- pmu_system_controller: system-controller at 10020000 {
- compatible = "samsung,exynos4412-pmu", "syscon";
- };
+&combiner {
+ samsung,combiner-nr = <20>;
+};
+
+&gic {
+ cpu-offset = <0x4000>;
};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v4 09/13] ARM: dts: exynos4: Use labels for overriding nodes in Odroid
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (7 preceding siblings ...)
2015-05-11 13:42 ` [PATCH v4 08/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4412 Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
2015-05-11 23:51 ` Eduardo Valentin
2015-05-11 13:42 ` [PATCH v4 10/13] ARM: dts: exynos4: Use labels for overriding nodes in SMDK4412 Krzysztof Kozlowski
` (3 subsequent siblings)
12 siblings, 1 reply; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 732 ++++++++++++------------
arch/arm/boot/dts/exynos4412-odroidx.dts | 16 +-
2 files changed, 374 insertions(+), 374 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index d6b49e5b32e9..ca7d168d1dd6 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -38,16 +38,6 @@
};
};
- i2s0: i2s at 03830000 {
- pinctrl-0 = <&i2s0_bus>;
- pinctrl-names = "default";
- status = "okay";
- clocks = <&clock_audss EXYNOS_I2S_BUS>,
- <&clock_audss EXYNOS_DOUT_AUD_BUS>,
- <&clock_audss EXYNOS_SCLK_I2S>;
- clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
- };
-
sound: sound {
compatible = "simple-audio-card";
assigned-clocks = <&clock_audss EXYNOS_MOUT_AUDSS>,
@@ -83,427 +73,437 @@
reset-gpios = <&gpk1 2 1>;
};
- mmc at 12550000 {
- pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo20_reg &buck8_reg>;
- mmc-pwrseq = <&emmc_pwrseq>;
- status = "okay";
-
- num-slots = <1>;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- bus-width = <8>;
- cap-mmc-highspeed;
- };
-
- watchdog at 10060000 {
- status = "okay";
- };
-
- rtc at 10070000 {
- status = "okay";
- clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
- clock-names = "rtc", "rtc_src";
- };
-
- g2d at 10800000 {
- status = "okay";
- };
-
camera {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
+ };
- fimc_0: fimc at 11800000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC0>,
- <&clock CLK_SCLK_FIMC0>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
- };
-
- fimc_1: fimc at 11810000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC1>,
- <&clock CLK_SCLK_FIMC1>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <0>;
};
- fimc_2: fimc at 11820000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC2>,
- <&clock CLK_SCLK_FIMC2>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
+ xusbxti {
+ compatible = "samsung,clock-xusbxti";
+ clock-frequency = <24000000>;
};
+ };
- fimc_3: fimc at 11830000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC3>,
- <&clock CLK_SCLK_FIMC3>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ cooling-maps {
+ map0 {
+ /* Corresponds to 800MHz at freq_table */
+ cooling-device = <&cpu0 7 7>;
+ };
+ map1 {
+ /* Corresponds to 200MHz at freq_table */
+ cooling-device = <&cpu0 13 13>;
+ };
+ };
};
};
+};
- sdhci at 12530000 {
- bus-width = <4>;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo4_reg &ldo21_reg>;
- cd-gpios = <&gpk2 2 0>;
- cd-inverted;
- status = "okay";
- };
+/* RSTN signal for eMMC */
+&sd1_cd {
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+};
- serial at 13800000 {
- status = "okay";
+&pinctrl_1 {
+ gpio_power_key: power_key {
+ samsung,pins = "gpx1-3";
+ samsung,pin-pud = <0>;
};
- serial at 13810000 {
- status = "okay";
+ max77686_irq: max77686-irq {
+ samsung,pins = "gpx3-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
};
- fixed-rate-clocks {
- xxti {
- compatible = "samsung,clock-xxti";
- clock-frequency = <0>;
- };
-
- xusbxti {
- compatible = "samsung,clock-xusbxti";
- clock-frequency = <24000000>;
- };
+ hdmi_hpd: hdmi-hpd {
+ samsung,pins = "gpx3-7";
+ samsung,pin-pud = <1>;
};
+};
- i2c at 13860000 {
- pinctrl-0 = <&i2c0_bus>;
- pinctrl-names = "default";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <400000>;
- status = "okay";
+&ehci {
+ status = "okay";
+};
- usb3503: usb3503 at 08 {
- compatible = "smsc,usb3503";
- reg = <0x08>;
+&exynos_usbphy {
+ status = "okay";
+};
- intn-gpios = <&gpx3 0 0>;
- connect-gpios = <&gpx3 4 0>;
- reset-gpios = <&gpx3 5 0>;
- initial-mode = <1>;
- };
+&fimc_0 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC0>,
+ <&clock CLK_SCLK_FIMC0>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- max77686: pmic at 09 {
- compatible = "maxim,max77686";
- interrupt-parent = <&gpx3>;
- interrupts = <2 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&max77686_irq>;
- reg = <0x09>;
- #clock-cells = <1>;
-
- voltage-regulators {
- ldo1_reg: LDO1 {
- regulator-name = "VDD_ALIVE_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
+&fimc_1 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC1>,
+ <&clock CLK_SCLK_FIMC1>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- ldo2_reg: LDO2 {
- regulator-name = "VDDQ_M1_2_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
+&fimc_2 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC2>,
+ <&clock CLK_SCLK_FIMC2>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- ldo3_reg: LDO3 {
- regulator-name = "VDDQ_EXT_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
+&fimc_3 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC3>,
+ <&clock CLK_SCLK_FIMC3>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- ldo4_reg: LDO4 {
- regulator-name = "VDDQ_MMC2_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+&g2d {
+ status = "okay";
+};
- ldo5_reg: LDO5 {
- regulator-name = "VDDQ_MMC1_3_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+&hdmi {
+ hpd-gpio = <&gpx3 7 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd>;
+ vdd-supply = <&ldo8_reg>;
+ vdd_osc-supply = <&ldo10_reg>;
+ vdd_pll-supply = <&ldo8_reg>;
+ ddc = <&i2c_2>;
+ status = "okay";
+};
- ldo6_reg: LDO6 {
- regulator-name = "VDD10_MPLL_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
+&hsotg {
+ dr_mode = "peripheral";
+ status = "okay";
+ vusb_d-supply = <&ldo15_reg>;
+ vusb_a-supply = <&ldo12_reg>;
+};
- ldo7_reg: LDO7 {
- regulator-name = "VDD10_XPLL_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
+&i2c_0 {
+ pinctrl-0 = <&i2c0_bus>;
+ pinctrl-names = "default";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <400000>;
+ status = "okay";
+
+ usb3503: usb3503 at 08 {
+ compatible = "smsc,usb3503";
+ reg = <0x08>;
+
+ intn-gpios = <&gpx3 0 0>;
+ connect-gpios = <&gpx3 4 0>;
+ reset-gpios = <&gpx3 5 0>;
+ initial-mode = <1>;
+ };
- ldo8_reg: ldo at 8 {
- regulator-compatible = "LDO8";
- regulator-name = "VDD10_HDMI_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
+ max77686: pmic at 09 {
+ compatible = "maxim,max77686";
+ interrupt-parent = <&gpx3>;
+ interrupts = <2 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&max77686_irq>;
+ reg = <0x09>;
+ #clock-cells = <1>;
+
+ voltage-regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
- ldo10_reg: ldo at 10 {
- regulator-compatible = "LDO10";
- regulator-name = "VDDQ_MIPIHSI_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ ldo2_reg: LDO2 {
+ regulator-name = "VDDQ_M1_2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- ldo11_reg: LDO11 {
- regulator-name = "VDD18_ABB1_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
+ ldo3_reg: LDO3 {
+ regulator-name = "VDDQ_EXT_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- ldo12_reg: LDO12 {
- regulator-name = "VDD33_USB_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo4_reg: LDO4 {
+ regulator-name = "VDDQ_MMC2_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- ldo13_reg: LDO13 {
- regulator-name = "VDDQ_C2C_W_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo5_reg: LDO5 {
+ regulator-name = "VDDQ_MMC1_3_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- ldo14_reg: LDO14 {
- regulator-name = "VDD18_ABB0_2_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD10_MPLL_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
- ldo15_reg: LDO15 {
- regulator-name = "VDD10_HSIC_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD10_XPLL_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
- ldo16_reg: LDO16 {
- regulator-name = "VDD18_HSIC_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo8_reg: ldo at 8 {
+ regulator-compatible = "LDO8";
+ regulator-name = "VDD10_HDMI_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
- ldo20_reg: LDO20 {
- regulator-name = "LDO20_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- };
+ ldo10_reg: ldo at 10 {
+ regulator-compatible = "LDO10";
+ regulator-name = "VDDQ_MIPIHSI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- ldo21_reg: LDO21 {
- regulator-name = "LDO21_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD18_ABB1_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- ldo25_reg: LDO25 {
- regulator-name = "VDDQ_LCD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD33_USB_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck1_reg: BUCK1 {
- regulator-name = "vdd_mif";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo13_reg: LDO13 {
+ regulator-name = "VDDQ_C2C_W_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck2_reg: BUCK2 {
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo14_reg: LDO14 {
+ regulator-name = "VDD18_ABB0_2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck3_reg: BUCK3 {
- regulator-name = "vdd_int";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo15_reg: LDO15 {
+ regulator-name = "VDD10_HSIC_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck4_reg: BUCK4 {
- regulator-name = "vdd_g3d";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1100000>;
- regulator-microvolt-offset = <50000>;
- };
+ ldo16_reg: LDO16 {
+ regulator-name = "VDD18_HSIC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck5_reg: BUCK5 {
- regulator-name = "VDDQ_CKEM1_2_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo20_reg: LDO20 {
+ regulator-name = "LDO20_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
- buck6_reg: BUCK6 {
- regulator-name = "BUCK6_1.35V";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo21_reg: LDO21 {
+ regulator-name = "LDO21_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck7_reg: BUCK7 {
- regulator-name = "BUCK7_2.0V";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
+ ldo25_reg: LDO25 {
+ regulator-name = "VDDQ_LCD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck8_reg: BUCK8 {
- regulator-name = "BUCK8_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
};
- };
- };
- i2c at 13870000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_bus>;
- status = "okay";
- max98090: max98090 at 10 {
- compatible = "maxim,max98090";
- reg = <0x10>;
- interrupt-parent = <&gpx0>;
- interrupts = <0 0>;
- clocks = <&i2s0 CLK_I2S_CDCLK>;
- clock-names = "mclk";
- #sound-dai-cells = <0>;
- };
- };
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- exynos-usbphy at 125B0000 {
- status = "okay";
- };
+ buck3_reg: BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- hsotg at 12480000 {
- dr_mode = "peripheral";
- status = "okay";
- vusb_d-supply = <&ldo15_reg>;
- vusb_a-supply = <&ldo12_reg>;
- };
+ buck4_reg: BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-microvolt-offset = <50000>;
+ };
- ehci: ehci at 12580000 {
- status = "okay";
- };
+ buck5_reg: BUCK5 {
+ regulator-name = "VDDQ_CKEM1_2_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- tmu at 100C0000 {
- vtmu-supply = <&ldo10_reg>;
- status = "okay";
- };
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6_1.35V";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- thermal-zones {
- cpu_thermal: cpu-thermal {
- cooling-maps {
- map0 {
- /* Corresponds to 800MHz at freq_table */
- cooling-device = <&cpu0 7 7>;
- };
- map1 {
- /* Corresponds to 200MHz at freq_table */
- cooling-device = <&cpu0 13 13>;
- };
- };
+ buck7_reg: BUCK7 {
+ regulator-name = "BUCK7_2.0V";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "BUCK8_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
};
};
+};
- mixer: mixer at 12C10000 {
- status = "okay";
+&i2c_1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
+ status = "okay";
+ max98090: max98090 at 10 {
+ compatible = "maxim,max98090";
+ reg = <0x10>;
+ interrupt-parent = <&gpx0>;
+ interrupts = <0 0>;
+ clocks = <&i2s0 CLK_I2S_CDCLK>;
+ clock-names = "mclk";
+ #sound-dai-cells = <0>;
};
+};
- hdmi at 12D00000 {
- hpd-gpio = <&gpx3 7 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_hpd>;
- vdd-supply = <&ldo8_reg>;
- vdd_osc-supply = <&ldo10_reg>;
- vdd_pll-supply = <&ldo8_reg>;
- ddc = <&hdmi_ddc>;
- status = "okay";
- };
+&i2c_2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+};
- hdmi_ddc: i2c at 13880000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_bus>;
- };
+&i2c_8 {
+ status = "okay";
+};
- i2c at 138E0000 {
- status = "okay";
- };
+&i2s0 {
+ pinctrl-0 = <&i2s0_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+ clocks = <&clock_audss EXYNOS_I2S_BUS>,
+ <&clock_audss EXYNOS_DOUT_AUD_BUS>,
+ <&clock_audss EXYNOS_SCLK_I2S>;
+ clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
};
-/* RSTN signal for eMMC */
-&sd1_cd {
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+&mixer {
+ status = "okay";
};
-&pinctrl_1 {
- gpio_power_key: power_key {
- samsung,pins = "gpx1-3";
- samsung,pin-pud = <0>;
- };
+&mshc_0 {
+ pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
+ pinctrl-names = "default";
+ vmmc-supply = <&ldo20_reg &buck8_reg>;
+ mmc-pwrseq = <&emmc_pwrseq>;
+ status = "okay";
+
+ num-slots = <1>;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+};
- max77686_irq: max77686-irq {
- samsung,pins = "gpx3-2";
- samsung,pin-function = <0>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
+&rtc {
+ status = "okay";
+ clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
+ clock-names = "rtc", "rtc_src";
+};
- hdmi_hpd: hdmi-hpd {
- samsung,pins = "gpx3-7";
- samsung,pin-pud = <1>;
- };
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+ pinctrl-names = "default";
+ vmmc-supply = <&ldo4_reg &ldo21_reg>;
+ cd-gpios = <&gpk2 2 0>;
+ cd-inverted;
+ status = "okay";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&tmu {
+ vtmu-supply = <&ldo10_reg>;
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts
index cb1cfe7239c4..679ac103ebf6 100644
--- a/arch/arm/boot/dts/exynos4412-odroidx.dts
+++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
@@ -38,14 +38,6 @@
};
};
- serial at 13820000 {
- status = "okay";
- };
-
- serial at 13830000 {
- status = "okay";
- };
-
gpio_keys {
pinctrl-0 = <&gpio_power_key &gpio_home_key>;
@@ -83,3 +75,11 @@
samsung,pin-pud = <0>;
};
};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v4 09/13] ARM: dts: exynos4: Use labels for overriding nodes in Odroid
2015-05-11 13:42 ` [PATCH v4 09/13] ARM: dts: exynos4: Use labels for overriding nodes in Odroid Krzysztof Kozlowski
@ 2015-05-11 23:51 ` Eduardo Valentin
0 siblings, 0 replies; 21+ messages in thread
From: Eduardo Valentin @ 2015-05-11 23:51 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, May 11, 2015 at 10:42:49PM +0900, Krzysztof Kozlowski wrote:
> Usage of labels instead of full paths reduces possible mistakes when
> overriding nodes.
>
> Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Wrt thermal zones:
Acked-by: Eduardo Valentin <edubezval@gmail.com>
> ---
> arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 732 ++++++++++++------------
> arch/arm/boot/dts/exynos4412-odroidx.dts | 16 +-
> 2 files changed, 374 insertions(+), 374 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
> index d6b49e5b32e9..ca7d168d1dd6 100644
> --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
> +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
> @@ -38,16 +38,6 @@
> };
> };
>
> - i2s0: i2s at 03830000 {
> - pinctrl-0 = <&i2s0_bus>;
> - pinctrl-names = "default";
> - status = "okay";
> - clocks = <&clock_audss EXYNOS_I2S_BUS>,
> - <&clock_audss EXYNOS_DOUT_AUD_BUS>,
> - <&clock_audss EXYNOS_SCLK_I2S>;
> - clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
> - };
> -
> sound: sound {
> compatible = "simple-audio-card";
> assigned-clocks = <&clock_audss EXYNOS_MOUT_AUDSS>,
> @@ -83,427 +73,437 @@
> reset-gpios = <&gpk1 2 1>;
> };
>
> - mmc at 12550000 {
> - pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
> - pinctrl-names = "default";
> - vmmc-supply = <&ldo20_reg &buck8_reg>;
> - mmc-pwrseq = <&emmc_pwrseq>;
> - status = "okay";
> -
> - num-slots = <1>;
> - broken-cd;
> - card-detect-delay = <200>;
> - samsung,dw-mshc-ciu-div = <3>;
> - samsung,dw-mshc-sdr-timing = <2 3>;
> - samsung,dw-mshc-ddr-timing = <1 2>;
> - bus-width = <8>;
> - cap-mmc-highspeed;
> - };
> -
> - watchdog at 10060000 {
> - status = "okay";
> - };
> -
> - rtc at 10070000 {
> - status = "okay";
> - clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
> - clock-names = "rtc", "rtc_src";
> - };
> -
> - g2d at 10800000 {
> - status = "okay";
> - };
> -
> camera {
> status = "okay";
> pinctrl-names = "default";
> pinctrl-0 = <>;
> + };
>
> - fimc_0: fimc at 11800000 {
> - status = "okay";
> - assigned-clocks = <&clock CLK_MOUT_FIMC0>,
> - <&clock CLK_SCLK_FIMC0>;
> - assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
> - assigned-clock-rates = <0>, <176000000>;
> - };
> -
> - fimc_1: fimc at 11810000 {
> - status = "okay";
> - assigned-clocks = <&clock CLK_MOUT_FIMC1>,
> - <&clock CLK_SCLK_FIMC1>;
> - assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
> - assigned-clock-rates = <0>, <176000000>;
> + fixed-rate-clocks {
> + xxti {
> + compatible = "samsung,clock-xxti";
> + clock-frequency = <0>;
> };
>
> - fimc_2: fimc at 11820000 {
> - status = "okay";
> - assigned-clocks = <&clock CLK_MOUT_FIMC2>,
> - <&clock CLK_SCLK_FIMC2>;
> - assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
> - assigned-clock-rates = <0>, <176000000>;
> + xusbxti {
> + compatible = "samsung,clock-xusbxti";
> + clock-frequency = <24000000>;
> };
> + };
>
> - fimc_3: fimc at 11830000 {
> - status = "okay";
> - assigned-clocks = <&clock CLK_MOUT_FIMC3>,
> - <&clock CLK_SCLK_FIMC3>;
> - assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
> - assigned-clock-rates = <0>, <176000000>;
> + thermal-zones {
> + cpu_thermal: cpu-thermal {
> + cooling-maps {
> + map0 {
> + /* Corresponds to 800MHz at freq_table */
> + cooling-device = <&cpu0 7 7>;
> + };
> + map1 {
> + /* Corresponds to 200MHz at freq_table */
> + cooling-device = <&cpu0 13 13>;
> + };
> + };
> };
> };
> +};
>
> - sdhci at 12530000 {
> - bus-width = <4>;
> - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
> - pinctrl-names = "default";
> - vmmc-supply = <&ldo4_reg &ldo21_reg>;
> - cd-gpios = <&gpk2 2 0>;
> - cd-inverted;
> - status = "okay";
> - };
> +/* RSTN signal for eMMC */
> +&sd1_cd {
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> +};
>
> - serial at 13800000 {
> - status = "okay";
> +&pinctrl_1 {
> + gpio_power_key: power_key {
> + samsung,pins = "gpx1-3";
> + samsung,pin-pud = <0>;
> };
>
> - serial at 13810000 {
> - status = "okay";
> + max77686_irq: max77686-irq {
> + samsung,pins = "gpx3-2";
> + samsung,pin-function = <0>;
> + samsung,pin-pud = <0>;
> + samsung,pin-drv = <0>;
> };
>
> - fixed-rate-clocks {
> - xxti {
> - compatible = "samsung,clock-xxti";
> - clock-frequency = <0>;
> - };
> -
> - xusbxti {
> - compatible = "samsung,clock-xusbxti";
> - clock-frequency = <24000000>;
> - };
> + hdmi_hpd: hdmi-hpd {
> + samsung,pins = "gpx3-7";
> + samsung,pin-pud = <1>;
> };
> +};
>
> - i2c at 13860000 {
> - pinctrl-0 = <&i2c0_bus>;
> - pinctrl-names = "default";
> - samsung,i2c-sda-delay = <100>;
> - samsung,i2c-max-bus-freq = <400000>;
> - status = "okay";
> +&ehci {
> + status = "okay";
> +};
>
> - usb3503: usb3503 at 08 {
> - compatible = "smsc,usb3503";
> - reg = <0x08>;
> +&exynos_usbphy {
> + status = "okay";
> +};
>
> - intn-gpios = <&gpx3 0 0>;
> - connect-gpios = <&gpx3 4 0>;
> - reset-gpios = <&gpx3 5 0>;
> - initial-mode = <1>;
> - };
> +&fimc_0 {
> + status = "okay";
> + assigned-clocks = <&clock CLK_MOUT_FIMC0>,
> + <&clock CLK_SCLK_FIMC0>;
> + assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
> + assigned-clock-rates = <0>, <176000000>;
> +};
>
> - max77686: pmic at 09 {
> - compatible = "maxim,max77686";
> - interrupt-parent = <&gpx3>;
> - interrupts = <2 0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&max77686_irq>;
> - reg = <0x09>;
> - #clock-cells = <1>;
> -
> - voltage-regulators {
> - ldo1_reg: LDO1 {
> - regulator-name = "VDD_ALIVE_1.0V";
> - regulator-min-microvolt = <1000000>;
> - regulator-max-microvolt = <1000000>;
> - regulator-always-on;
> - };
> +&fimc_1 {
> + status = "okay";
> + assigned-clocks = <&clock CLK_MOUT_FIMC1>,
> + <&clock CLK_SCLK_FIMC1>;
> + assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
> + assigned-clock-rates = <0>, <176000000>;
> +};
>
> - ldo2_reg: LDO2 {
> - regulator-name = "VDDQ_M1_2_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - };
> +&fimc_2 {
> + status = "okay";
> + assigned-clocks = <&clock CLK_MOUT_FIMC2>,
> + <&clock CLK_SCLK_FIMC2>;
> + assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
> + assigned-clock-rates = <0>, <176000000>;
> +};
>
> - ldo3_reg: LDO3 {
> - regulator-name = "VDDQ_EXT_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - };
> +&fimc_3 {
> + status = "okay";
> + assigned-clocks = <&clock CLK_MOUT_FIMC3>,
> + <&clock CLK_SCLK_FIMC3>;
> + assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
> + assigned-clock-rates = <0>, <176000000>;
> +};
>
> - ldo4_reg: LDO4 {
> - regulator-name = "VDDQ_MMC2_2.8V";
> - regulator-min-microvolt = <2800000>;
> - regulator-max-microvolt = <2800000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> +&g2d {
> + status = "okay";
> +};
>
> - ldo5_reg: LDO5 {
> - regulator-name = "VDDQ_MMC1_3_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> +&hdmi {
> + hpd-gpio = <&gpx3 7 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&hdmi_hpd>;
> + vdd-supply = <&ldo8_reg>;
> + vdd_osc-supply = <&ldo10_reg>;
> + vdd_pll-supply = <&ldo8_reg>;
> + ddc = <&i2c_2>;
> + status = "okay";
> +};
>
> - ldo6_reg: LDO6 {
> - regulator-name = "VDD10_MPLL_1.0V";
> - regulator-min-microvolt = <1000000>;
> - regulator-max-microvolt = <1000000>;
> - regulator-always-on;
> - };
> +&hsotg {
> + dr_mode = "peripheral";
> + status = "okay";
> + vusb_d-supply = <&ldo15_reg>;
> + vusb_a-supply = <&ldo12_reg>;
> +};
>
> - ldo7_reg: LDO7 {
> - regulator-name = "VDD10_XPLL_1.0V";
> - regulator-min-microvolt = <1000000>;
> - regulator-max-microvolt = <1000000>;
> - regulator-always-on;
> - };
> +&i2c_0 {
> + pinctrl-0 = <&i2c0_bus>;
> + pinctrl-names = "default";
> + samsung,i2c-sda-delay = <100>;
> + samsung,i2c-max-bus-freq = <400000>;
> + status = "okay";
> +
> + usb3503: usb3503 at 08 {
> + compatible = "smsc,usb3503";
> + reg = <0x08>;
> +
> + intn-gpios = <&gpx3 0 0>;
> + connect-gpios = <&gpx3 4 0>;
> + reset-gpios = <&gpx3 5 0>;
> + initial-mode = <1>;
> + };
>
> - ldo8_reg: ldo at 8 {
> - regulator-compatible = "LDO8";
> - regulator-name = "VDD10_HDMI_1.0V";
> - regulator-min-microvolt = <1000000>;
> - regulator-max-microvolt = <1000000>;
> - };
> + max77686: pmic at 09 {
> + compatible = "maxim,max77686";
> + interrupt-parent = <&gpx3>;
> + interrupts = <2 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&max77686_irq>;
> + reg = <0x09>;
> + #clock-cells = <1>;
> +
> + voltage-regulators {
> + ldo1_reg: LDO1 {
> + regulator-name = "VDD_ALIVE_1.0V";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + };
>
> - ldo10_reg: ldo at 10 {
> - regulator-compatible = "LDO10";
> - regulator-name = "VDDQ_MIPIHSI_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - };
> + ldo2_reg: LDO2 {
> + regulator-name = "VDDQ_M1_2_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
>
> - ldo11_reg: LDO11 {
> - regulator-name = "VDD18_ABB1_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - };
> + ldo3_reg: LDO3 {
> + regulator-name = "VDDQ_EXT_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
>
> - ldo12_reg: LDO12 {
> - regulator-name = "VDD33_USB_3.3V";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> + ldo4_reg: LDO4 {
> + regulator-name = "VDDQ_MMC2_2.8V";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - ldo13_reg: LDO13 {
> - regulator-name = "VDDQ_C2C_W_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> + ldo5_reg: LDO5 {
> + regulator-name = "VDDQ_MMC1_3_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - ldo14_reg: LDO14 {
> - regulator-name = "VDD18_ABB0_2_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> + ldo6_reg: LDO6 {
> + regulator-name = "VDD10_MPLL_1.0V";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + };
>
> - ldo15_reg: LDO15 {
> - regulator-name = "VDD10_HSIC_1.0V";
> - regulator-min-microvolt = <1000000>;
> - regulator-max-microvolt = <1000000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> + ldo7_reg: LDO7 {
> + regulator-name = "VDD10_XPLL_1.0V";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + };
>
> - ldo16_reg: LDO16 {
> - regulator-name = "VDD18_HSIC_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> + ldo8_reg: ldo at 8 {
> + regulator-compatible = "LDO8";
> + regulator-name = "VDD10_HDMI_1.0V";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + };
>
> - ldo20_reg: LDO20 {
> - regulator-name = "LDO20_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-boot-on;
> - };
> + ldo10_reg: ldo at 10 {
> + regulator-compatible = "LDO10";
> + regulator-name = "VDDQ_MIPIHSI_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
>
> - ldo21_reg: LDO21 {
> - regulator-name = "LDO21_3.3V";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> + ldo11_reg: LDO11 {
> + regulator-name = "VDD18_ABB1_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
>
> - ldo25_reg: LDO25 {
> - regulator-name = "VDDQ_LCD_1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> + ldo12_reg: LDO12 {
> + regulator-name = "VDD33_USB_3.3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - buck1_reg: BUCK1 {
> - regulator-name = "vdd_mif";
> - regulator-min-microvolt = <1000000>;
> - regulator-max-microvolt = <1000000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> + ldo13_reg: LDO13 {
> + regulator-name = "VDDQ_C2C_W_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - buck2_reg: BUCK2 {
> - regulator-name = "vdd_arm";
> - regulator-min-microvolt = <900000>;
> - regulator-max-microvolt = <1350000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> + ldo14_reg: LDO14 {
> + regulator-name = "VDD18_ABB0_2_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - buck3_reg: BUCK3 {
> - regulator-name = "vdd_int";
> - regulator-min-microvolt = <1000000>;
> - regulator-max-microvolt = <1000000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> + ldo15_reg: LDO15 {
> + regulator-name = "VDD10_HSIC_1.0V";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - buck4_reg: BUCK4 {
> - regulator-name = "vdd_g3d";
> - regulator-min-microvolt = <900000>;
> - regulator-max-microvolt = <1100000>;
> - regulator-microvolt-offset = <50000>;
> - };
> + ldo16_reg: LDO16 {
> + regulator-name = "VDD18_HSIC_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - buck5_reg: BUCK5 {
> - regulator-name = "VDDQ_CKEM1_2_1.2V";
> - regulator-min-microvolt = <1200000>;
> - regulator-max-microvolt = <1200000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> + ldo20_reg: LDO20 {
> + regulator-name = "LDO20_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + };
>
> - buck6_reg: BUCK6 {
> - regulator-name = "BUCK6_1.35V";
> - regulator-min-microvolt = <1350000>;
> - regulator-max-microvolt = <1350000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> + ldo21_reg: LDO21 {
> + regulator-name = "LDO21_3.3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - buck7_reg: BUCK7 {
> - regulator-name = "BUCK7_2.0V";
> - regulator-min-microvolt = <2000000>;
> - regulator-max-microvolt = <2000000>;
> - regulator-always-on;
> - };
> + ldo25_reg: LDO25 {
> + regulator-name = "VDDQ_LCD_1.8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - buck8_reg: BUCK8 {
> - regulator-name = "BUCK8_2.8V";
> - regulator-min-microvolt = <2800000>;
> - regulator-max-microvolt = <2800000>;
> - };
> + buck1_reg: BUCK1 {
> + regulator-name = "vdd_mif";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + regulator-boot-on;
> };
> - };
> - };
>
> - i2c at 13870000 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c1_bus>;
> - status = "okay";
> - max98090: max98090 at 10 {
> - compatible = "maxim,max98090";
> - reg = <0x10>;
> - interrupt-parent = <&gpx0>;
> - interrupts = <0 0>;
> - clocks = <&i2s0 CLK_I2S_CDCLK>;
> - clock-names = "mclk";
> - #sound-dai-cells = <0>;
> - };
> - };
> + buck2_reg: BUCK2 {
> + regulator-name = "vdd_arm";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - exynos-usbphy at 125B0000 {
> - status = "okay";
> - };
> + buck3_reg: BUCK3 {
> + regulator-name = "vdd_int";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - hsotg at 12480000 {
> - dr_mode = "peripheral";
> - status = "okay";
> - vusb_d-supply = <&ldo15_reg>;
> - vusb_a-supply = <&ldo12_reg>;
> - };
> + buck4_reg: BUCK4 {
> + regulator-name = "vdd_g3d";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-microvolt-offset = <50000>;
> + };
>
> - ehci: ehci at 12580000 {
> - status = "okay";
> - };
> + buck5_reg: BUCK5 {
> + regulator-name = "VDDQ_CKEM1_2_1.2V";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - tmu at 100C0000 {
> - vtmu-supply = <&ldo10_reg>;
> - status = "okay";
> - };
> + buck6_reg: BUCK6 {
> + regulator-name = "BUCK6_1.35V";
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
>
> - thermal-zones {
> - cpu_thermal: cpu-thermal {
> - cooling-maps {
> - map0 {
> - /* Corresponds to 800MHz at freq_table */
> - cooling-device = <&cpu0 7 7>;
> - };
> - map1 {
> - /* Corresponds to 200MHz at freq_table */
> - cooling-device = <&cpu0 13 13>;
> - };
> - };
> + buck7_reg: BUCK7 {
> + regulator-name = "BUCK7_2.0V";
> + regulator-min-microvolt = <2000000>;
> + regulator-max-microvolt = <2000000>;
> + regulator-always-on;
> + };
> +
> + buck8_reg: BUCK8 {
> + regulator-name = "BUCK8_2.8V";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + };
> };
> };
> +};
>
> - mixer: mixer at 12C10000 {
> - status = "okay";
> +&i2c_1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_bus>;
> + status = "okay";
> + max98090: max98090 at 10 {
> + compatible = "maxim,max98090";
> + reg = <0x10>;
> + interrupt-parent = <&gpx0>;
> + interrupts = <0 0>;
> + clocks = <&i2s0 CLK_I2S_CDCLK>;
> + clock-names = "mclk";
> + #sound-dai-cells = <0>;
> };
> +};
>
> - hdmi at 12D00000 {
> - hpd-gpio = <&gpx3 7 0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&hdmi_hpd>;
> - vdd-supply = <&ldo8_reg>;
> - vdd_osc-supply = <&ldo10_reg>;
> - vdd_pll-supply = <&ldo8_reg>;
> - ddc = <&hdmi_ddc>;
> - status = "okay";
> - };
> +&i2c_2 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_bus>;
> +};
>
> - hdmi_ddc: i2c at 13880000 {
> - status = "okay";
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c2_bus>;
> - };
> +&i2c_8 {
> + status = "okay";
> +};
>
> - i2c at 138E0000 {
> - status = "okay";
> - };
> +&i2s0 {
> + pinctrl-0 = <&i2s0_bus>;
> + pinctrl-names = "default";
> + status = "okay";
> + clocks = <&clock_audss EXYNOS_I2S_BUS>,
> + <&clock_audss EXYNOS_DOUT_AUD_BUS>,
> + <&clock_audss EXYNOS_SCLK_I2S>;
> + clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
> };
>
> -/* RSTN signal for eMMC */
> -&sd1_cd {
> - samsung,pin-pud = <0>;
> - samsung,pin-drv = <0>;
> +&mixer {
> + status = "okay";
> };
>
> -&pinctrl_1 {
> - gpio_power_key: power_key {
> - samsung,pins = "gpx1-3";
> - samsung,pin-pud = <0>;
> - };
> +&mshc_0 {
> + pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
> + pinctrl-names = "default";
> + vmmc-supply = <&ldo20_reg &buck8_reg>;
> + mmc-pwrseq = <&emmc_pwrseq>;
> + status = "okay";
> +
> + num-slots = <1>;
> + broken-cd;
> + card-detect-delay = <200>;
> + samsung,dw-mshc-ciu-div = <3>;
> + samsung,dw-mshc-sdr-timing = <2 3>;
> + samsung,dw-mshc-ddr-timing = <1 2>;
> + bus-width = <8>;
> + cap-mmc-highspeed;
> +};
>
> - max77686_irq: max77686-irq {
> - samsung,pins = "gpx3-2";
> - samsung,pin-function = <0>;
> - samsung,pin-pud = <0>;
> - samsung,pin-drv = <0>;
> - };
> +&rtc {
> + status = "okay";
> + clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
> + clock-names = "rtc", "rtc_src";
> +};
>
> - hdmi_hpd: hdmi-hpd {
> - samsung,pins = "gpx3-7";
> - samsung,pin-pud = <1>;
> - };
> +&sdhci_2 {
> + bus-width = <4>;
> + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
> + pinctrl-names = "default";
> + vmmc-supply = <&ldo4_reg &ldo21_reg>;
> + cd-gpios = <&gpk2 2 0>;
> + cd-inverted;
> + status = "okay";
> +};
> +
> +&serial_0 {
> + status = "okay";
> +};
> +
> +&serial_1 {
> + status = "okay";
> +};
> +
> +&tmu {
> + vtmu-supply = <&ldo10_reg>;
> + status = "okay";
> +};
> +
> +&watchdog {
> + status = "okay";
> };
> diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts
> index cb1cfe7239c4..679ac103ebf6 100644
> --- a/arch/arm/boot/dts/exynos4412-odroidx.dts
> +++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
> @@ -38,14 +38,6 @@
> };
> };
>
> - serial at 13820000 {
> - status = "okay";
> - };
> -
> - serial at 13830000 {
> - status = "okay";
> - };
> -
> gpio_keys {
> pinctrl-0 = <&gpio_power_key &gpio_home_key>;
>
> @@ -83,3 +75,11 @@
> samsung,pin-pud = <0>;
> };
> };
> +
> +&serial_2 {
> + status = "okay";
> +};
> +
> +&serial_3 {
> + status = "okay";
> +};
> --
> 2.1.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 490 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150511/35e4b26d/attachment.sig>
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH v4 10/13] ARM: dts: exynos4: Use labels for overriding nodes in SMDK4412
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (8 preceding siblings ...)
2015-05-11 13:42 ` [PATCH v4 09/13] ARM: dts: exynos4: Use labels for overriding nodes in Odroid Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
2015-05-11 13:42 ` [PATCH v4 11/13] ARM: dts: exynos4: Use labels for overriding nodes in Trats2 Krzysztof Kozlowski
` (2 subsequent siblings)
12 siblings, 0 replies; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4412-smdk4412.dts | 210 +++++++++++++++---------------
1 file changed, 105 insertions(+), 105 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412-smdk4412.dts b/arch/arm/boot/dts/exynos4412-smdk4412.dts
index b9256afbcc68..c2421df1fa43 100644
--- a/arch/arm/boot/dts/exynos4412-smdk4412.dts
+++ b/arch/arm/boot/dts/exynos4412-smdk4412.dts
@@ -28,135 +28,135 @@
stdout-path = &serial_1;
};
- g2d at 10800000 {
- status = "okay";
- };
-
- pinctrl at 11000000 {
- keypad_rows: keypad-rows {
- samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
- samsung,pin-function = <3>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <0>;
};
- keypad_cols: keypad-cols {
- samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
- "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
- samsung,pin-function = <3>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ xusbxti {
+ compatible = "samsung,clock-xusbxti";
+ clock-frequency = <24000000>;
};
};
+};
- keypad at 100A0000 {
- samsung,keypad-num-rows = <3>;
- samsung,keypad-num-columns = <8>;
- linux,keypad-no-autorepeat;
- linux,keypad-wakeup;
- pinctrl-0 = <&keypad_rows &keypad_cols>;
- pinctrl-names = "default";
- status = "okay";
-
- key_1 {
- keypad,row = <1>;
- keypad,column = <3>;
- linux,code = <2>;
- };
-
- key_2 {
- keypad,row = <1>;
- keypad,column = <4>;
- linux,code = <3>;
- };
-
- key_3 {
- keypad,row = <1>;
- keypad,column = <5>;
- linux,code = <4>;
- };
-
- key_4 {
- keypad,row = <1>;
- keypad,column = <6>;
- linux,code = <5>;
- };
+&g2d {
+ status = "okay";
+};
- key_5 {
- keypad,row = <1>;
- keypad,column = <7>;
- linux,code = <6>;
- };
+&keypad {
+ samsung,keypad-num-rows = <3>;
+ samsung,keypad-num-columns = <8>;
+ linux,keypad-no-autorepeat;
+ linux,keypad-wakeup;
+ pinctrl-0 = <&keypad_rows &keypad_cols>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ key_1 {
+ keypad,row = <1>;
+ keypad,column = <3>;
+ linux,code = <2>;
+ };
- key_A {
- keypad,row = <2>;
- keypad,column = <6>;
- linux,code = <30>;
- };
+ key_2 {
+ keypad,row = <1>;
+ keypad,column = <4>;
+ linux,code = <3>;
+ };
- key_B {
- keypad,row = <2>;
- keypad,column = <7>;
- linux,code = <48>;
- };
+ key_3 {
+ keypad,row = <1>;
+ keypad,column = <5>;
+ linux,code = <4>;
+ };
- key_C {
- keypad,row = <0>;
- keypad,column = <5>;
- linux,code = <46>;
- };
+ key_4 {
+ keypad,row = <1>;
+ keypad,column = <6>;
+ linux,code = <5>;
+ };
- key_D {
- keypad,row = <2>;
- keypad,column = <5>;
- linux,code = <32>;
- };
+ key_5 {
+ keypad,row = <1>;
+ keypad,column = <7>;
+ linux,code = <6>;
+ };
- key_E {
- keypad,row = <0>;
- keypad,column = <7>;
- linux,code = <18>;
- };
+ key_A {
+ keypad,row = <2>;
+ keypad,column = <6>;
+ linux,code = <30>;
};
- sdhci at 12530000 {
- bus-width = <4>;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
- pinctrl-names = "default";
- status = "okay";
+ key_B {
+ keypad,row = <2>;
+ keypad,column = <7>;
+ linux,code = <48>;
};
- codec at 13400000 {
- samsung,mfc-r = <0x43000000 0x800000>;
- samsung,mfc-l = <0x51000000 0x800000>;
- status = "okay";
+ key_C {
+ keypad,row = <0>;
+ keypad,column = <5>;
+ linux,code = <46>;
};
- serial at 13800000 {
- status = "okay";
+ key_D {
+ keypad,row = <2>;
+ keypad,column = <5>;
+ linux,code = <32>;
};
- serial at 13810000 {
- status = "okay";
+ key_E {
+ keypad,row = <0>;
+ keypad,column = <7>;
+ linux,code = <18>;
};
+};
+
+&mfc {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+ status = "okay";
+};
- serial at 13820000 {
- status = "okay";
+&pinctrl_1 {
+ keypad_rows: keypad-rows {
+ samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
};
- serial at 13830000 {
- status = "okay";
+ keypad_cols: keypad-cols {
+ samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
+ "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
};
+};
- fixed-rate-clocks {
- xxti {
- compatible = "samsung,clock-xxti";
- clock-frequency = <0>;
- };
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
+ pinctrl-names = "default";
+ status = "okay";
+};
- xusbxti {
- compatible = "samsung,clock-xusbxti";
- clock-frequency = <24000000>;
- };
- };
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v4 11/13] ARM: dts: exynos4: Use labels for overriding nodes in Trats2
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (9 preceding siblings ...)
2015-05-11 13:42 ` [PATCH v4 10/13] ARM: dts: exynos4: Use labels for overriding nodes in SMDK4412 Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
2015-05-11 13:42 ` [PATCH v4 12/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4412 Origen Krzysztof Kozlowski
2015-05-11 13:42 ` [PATCH v4 13/13] ARM: dts: exynos4: Use labels for overriding nodes in Tiny4412 Krzysztof Kozlowski
12 siblings, 0 replies; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4412-trats2.dts | 1332 ++++++++++++++++---------------
1 file changed, 667 insertions(+), 665 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts
index c032cde11d5c..4d0cf22acea3 100644
--- a/arch/arm/boot/dts/exynos4412-trats2.dts
+++ b/arch/arm/boot/dts/exynos4412-trats2.dts
@@ -131,411 +131,6 @@
};
};
- adc: adc at 126C0000 {
- vdd-supply = <&ldo3_reg>;
- status = "okay";
- };
-
- i2c at 13890000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <400000>;
- pinctrl-0 = <&i2c3_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- mms114-touchscreen at 48 {
- compatible = "melfas,mms114";
- reg = <0x48>;
- interrupt-parent = <&gpm2>;
- interrupts = <3 2>;
- x-size = <720>;
- y-size = <1280>;
- avdd-supply = <&ldo23_reg>;
- vdd-supply = <&ldo24_reg>;
- };
- };
-
- i2c_0: i2c at 13860000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <400000>;
- pinctrl-0 = <&i2c0_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- s5c73m3 at 3c {
- compatible = "samsung,s5c73m3";
- reg = <0x3c>;
- standby-gpios = <&gpm0 1 1>; /* ISP_STANDBY */
- xshutdown-gpios = <&gpf1 3 1>; /* ISP_RESET */
- vdd-int-supply = <&buck9_reg>;
- vddio-cis-supply = <&ldo9_reg>;
- vdda-supply = <&ldo17_reg>;
- vddio-host-supply = <&ldo18_reg>;
- vdd-af-supply = <&cam_af_reg>;
- vdd-reg-supply = <&cam_io_reg>;
- clock-frequency = <24000000>;
- /* CAM_A_CLKOUT */
- clocks = <&camera 0>;
- clock-names = "cis_extclk";
- port {
- s5c73m3_ep: endpoint {
- remote-endpoint = <&csis0_ep>;
- data-lanes = <1 2 3 4>;
- };
- };
- };
- };
-
- i2c at 138A0000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <100000>;
- pinctrl-0 = <&i2c4_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- wm1811: wm1811 at 1a {
- compatible = "wlf,wm1811";
- reg = <0x1a>;
- clocks = <&pmu_system_controller 0>;
- clock-names = "MCLK1";
- DCVDD-supply = <&ldo3_reg>;
- DBVDD1-supply = <&ldo3_reg>;
- wlf,ldo1ena = <&gpj0 4 0>;
- };
- };
-
- i2c at 138D0000 {
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-slave-addr = <0x10>;
- samsung,i2c-max-bus-freq = <100000>;
- pinctrl-0 = <&i2c7_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- max77686: max77686_pmic at 09 {
- compatible = "maxim,max77686";
- interrupt-parent = <&gpx0>;
- interrupts = <7 0>;
- reg = <0x09>;
- #clock-cells = <1>;
-
- voltage-regulators {
- ldo1_reg: ldo1 {
- regulator-compatible = "LDO1";
- regulator-name = "VALIVE_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- ldo2_reg: ldo2 {
- regulator-compatible = "LDO2";
- regulator-name = "VM1M2_1.2V_AP";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo3_reg: ldo3 {
- regulator-compatible = "LDO3";
- regulator-name = "VCC_1.8V_AP";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo4_reg: ldo4 {
- regulator-compatible = "LDO4";
- regulator-name = "VCC_2.8V_AP";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- ldo5_reg: ldo5 {
- regulator-compatible = "LDO5";
- regulator-name = "VCC_1.8V_IO";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- ldo6_reg: ldo6 {
- regulator-compatible = "LDO6";
- regulator-name = "VMPLL_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo7_reg: ldo7 {
- regulator-compatible = "LDO7";
- regulator-name = "VPLL_1.0V_AP";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo8_reg: ldo8 {
- regulator-compatible = "LDO8";
- regulator-name = "VMIPI_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo9_reg: ldo9 {
- regulator-compatible = "LDO9";
- regulator-name = "CAM_ISP_MIPI_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- ldo10_reg: ldo10 {
- regulator-compatible = "LDO10";
- regulator-name = "VMIPI_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo11_reg: ldo11 {
- regulator-compatible = "LDO11";
- regulator-name = "VABB1_1.95V";
- regulator-min-microvolt = <1950000>;
- regulator-max-microvolt = <1950000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo12_reg: ldo12 {
- regulator-compatible = "LDO12";
- regulator-name = "VUOTG_3.0V";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo13_reg: ldo13 {
- regulator-compatible = "LDO13";
- regulator-name = "NFC_AVDD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo14_reg: ldo14 {
- regulator-compatible = "LDO14";
- regulator-name = "VABB2_1.95V";
- regulator-min-microvolt = <1950000>;
- regulator-max-microvolt = <1950000>;
- regulator-always-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- ldo15_reg: ldo15 {
- regulator-compatible = "LDO15";
- regulator-name = "VHSIC_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo16_reg: ldo16 {
- regulator-compatible = "LDO16";
- regulator-name = "VHSIC_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- ldo17_reg: ldo17 {
- regulator-compatible = "LDO17";
- regulator-name = "CAM_SENSOR_CORE_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
-
- ldo18_reg: ldo18 {
- regulator-compatible = "LDO18";
- regulator-name = "CAM_ISP_SEN_IO_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo19_reg: ldo19 {
- regulator-compatible = "LDO19";
- regulator-name = "VT_CAM_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo20_reg: ldo20 {
- regulator-compatible = "LDO20";
- regulator-name = "VDDQ_PRE_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo21_reg: ldo21 {
- regulator-compatible = "LDO21";
- regulator-name = "VTF_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>;
- };
-
- ldo22_reg: ldo22 {
- regulator-compatible = "LDO22";
- regulator-name = "VMEM_VDD_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
- };
-
- ldo23_reg: ldo23 {
- regulator-compatible = "LDO23";
- regulator-name = "TSP_AVDD_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo24_reg: ldo24 {
- regulator-compatible = "LDO24";
- regulator-name = "TSP_VDD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo25_reg: ldo25 {
- regulator-compatible = "LDO25";
- regulator-name = "LCD_VCC_3.3V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo26_reg: ldo26 {
- regulator-compatible = "LDO26";
- regulator-name = "MOTOR_VCC_3.0V";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- buck1_reg: buck1 {
- regulator-compatible = "BUCK1";
- regulator-name = "vdd_mif";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck2_reg: buck2 {
- regulator-compatible = "BUCK2";
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- buck3_reg: buck3 {
- regulator-compatible = "BUCK3";
- regulator-name = "vdd_int";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1150000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck4_reg: buck4 {
- regulator-compatible = "BUCK4";
- regulator-name = "vdd_g3d";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1150000>;
- regulator-boot-on;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- buck5_reg: buck5 {
- regulator-compatible = "BUCK5";
- regulator-name = "VMEM_1.2V_AP";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- };
-
- buck6_reg: buck6 {
- regulator-compatible = "BUCK6";
- regulator-name = "VCC_SUB_1.35V";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- };
-
- buck7_reg: buck7 {
- regulator-compatible = "BUCK7";
- regulator-name = "VCC_SUB_2.0V";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
-
- buck8_reg: buck8 {
- regulator-compatible = "BUCK8";
- regulator-name = "VMEM_VDDF_3.0V";
- regulator-min-microvolt = <2850000>;
- regulator-max-microvolt = <2850000>;
- maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
- };
-
- buck9_reg: buck9 {
- regulator-compatible = "BUCK9";
- regulator-name = "CAM_ISP_CORE_1.2V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1200000>;
- maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>;
- };
- };
- };
- };
-
i2c_max77693: i2c-gpio-1 {
compatible = "i2c-gpio";
gpios = <&gpm2 0 GPIO_ACTIVE_HIGH>, <&gpm2 1 GPIO_ACTIVE_HIGH>;
@@ -598,54 +193,6 @@
};
};
- mmc at 12550000 {
- num-slots = <1>;
- broken-cd;
- non-removable;
- card-detect-delay = <200>;
- vmmc-supply = <&ldo22_reg>;
- clock-frequency = <400000000>;
- samsung,dw-mshc-ciu-div = <0>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
- pinctrl-names = "default";
- status = "okay";
- bus-width = <8>;
- cap-mmc-highspeed;
- };
-
- sdhci at 12530000 {
- bus-width = <4>;
- cd-gpios = <&gpx3 4 0>;
- cd-inverted;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo21_reg>;
- status = "okay";
- };
-
- serial at 13800000 {
- status = "okay";
- };
-
- serial at 13810000 {
- status = "okay";
- };
-
- serial at 13820000 {
- status = "okay";
- };
-
- serial at 13830000 {
- status = "okay";
- };
-
- tmu at 100C0000 {
- vtmu-supply = <&ldo10_reg>;
- status = "okay";
- };
-
i2c_ak8975: i2c-gpio-0 {
compatible = "i2c-gpio";
gpios = <&gpy2 4 0>, <&gpy2 5 0>;
@@ -677,90 +224,6 @@
};
};
- spi_1: spi at 13930000 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_bus>;
- cs-gpios = <&gpb 5 0>;
- status = "okay";
-
- s5c73m3_spi: s5c73m3 {
- compatible = "samsung,s5c73m3";
- spi-max-frequency = <50000000>;
- reg = <0>;
- controller-data {
- samsung,spi-feedback-delay = <2>;
- };
- };
- };
-
- pwm: pwm at 139D0000 {
- pinctrl-0 = <&pwm0_out>;
- pinctrl-names = "default";
- samsung,pwm-outputs = <0>;
- status = "okay";
- };
-
- dsi_0: dsi at 11C80000 {
- vddcore-supply = <&ldo8_reg>;
- vddio-supply = <&ldo10_reg>;
- samsung,pll-clock-frequency = <24000000>;
- status = "okay";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 1 {
- reg = <1>;
-
- dsi_out: endpoint {
- remote-endpoint = <&dsi_in>;
- samsung,burst-clock-frequency = <500000000>;
- samsung,esc-clock-frequency = <20000000>;
- };
- };
- };
-
- panel at 0 {
- compatible = "samsung,s6e8aa0";
- reg = <0>;
- vdd3-supply = <&lcd_vdd3_reg>;
- vci-supply = <&ldo25_reg>;
- reset-gpios = <&gpy4 5 0>;
- power-on-delay= <50>;
- reset-delay = <100>;
- init-delay = <100>;
- flip-horizontal;
- flip-vertical;
- panel-width-mm = <58>;
- panel-height-mm = <103>;
-
- display-timings {
- timing-0 {
- clock-frequency = <0>;
- hactive = <720>;
- vactive = <1280>;
- hfront-porch = <5>;
- hback-porch = <5>;
- hsync-len = <5>;
- vfront-porch = <13>;
- vback-porch = <1>;
- vsync-len = <2>;
- };
- };
-
- port {
- dsi_in: endpoint {
- remote-endpoint = <&dsi_out>;
- };
- };
- };
- };
-
- fimd at 11c00000 {
- status = "okay";
- };
-
camera: camera {
pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>;
pinctrl-names = "default";
@@ -770,124 +233,7 @@
assigned-clock-parents = <&clock CLK_XUSBXTI>,
<&clock CLK_XUSBXTI>;
- fimc_0: fimc at 11800000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC0>,
- <&clock CLK_SCLK_FIMC0>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
- };
-
- fimc_1: fimc at 11810000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC1>,
- <&clock CLK_SCLK_FIMC1>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
- };
-
- fimc_2: fimc at 11820000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC2>,
- <&clock CLK_SCLK_FIMC2>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
- };
-
- fimc_3: fimc at 11830000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC3>,
- <&clock CLK_SCLK_FIMC3>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
- };
-
- csis_0: csis at 11880000 {
- status = "okay";
- vddcore-supply = <&ldo8_reg>;
- vddio-supply = <&ldo10_reg>;
- assigned-clocks = <&clock CLK_MOUT_CSIS0>,
- <&clock CLK_SCLK_CSIS0>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
-
- /* Camera C (3) MIPI CSI-2 (CSIS0) */
- port at 3 {
- reg = <3>;
- csis0_ep: endpoint {
- remote-endpoint = <&s5c73m3_ep>;
- data-lanes = <1 2 3 4>;
- samsung,csis-hs-settle = <12>;
- };
- };
- };
-
- csis_1: csis at 11890000 {
- status = "okay";
- vddcore-supply = <&ldo8_reg>;
- vddio-supply = <&ldo10_reg>;
- assigned-clocks = <&clock CLK_MOUT_CSIS1>,
- <&clock CLK_SCLK_CSIS1>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
-
- /* Camera D (4) MIPI CSI-2 (CSIS1) */
- port at 4 {
- reg = <4>;
- csis1_ep: endpoint {
- remote-endpoint = <&is_s5k6a3_ep>;
- data-lanes = <1>;
- samsung,csis-hs-settle = <18>;
- samsung,csis-wclk;
- };
- };
- };
-
- fimc_lite_0: fimc-lite at 12390000 {
- status = "okay";
- };
- fimc_lite_1: fimc-lite at 123A0000 {
- status = "okay";
- };
-
- fimc-is at 12000000 {
- pinctrl-0 = <&fimc_is_uart>;
- pinctrl-names = "default";
- status = "okay";
-
- i2c1_isp: i2c-isp at 12140000 {
- pinctrl-0 = <&fimc_is_i2c1>;
- pinctrl-names = "default";
-
- s5k6a3 at 10 {
- compatible = "samsung,s5k6a3";
- reg = <0x10>;
- svdda-supply = <&cam_io_reg>;
- svddio-supply = <&ldo19_reg>;
- afvdd-supply = <&ldo19_reg>;
- clock-frequency = <24000000>;
- /* CAM_B_CLKOUT */
- clocks = <&camera 1>;
- clock-names = "extclk";
- samsung,camclk-out = <1>;
- gpios = <&gpm1 6 0>;
-
- port {
- is_s5k6a3_ep: endpoint {
- remote-endpoint = <&csis1_ep>;
- data-lanes = <1>;
- };
- };
- };
- };
- };
- };
-
- i2s0: i2s at 03830000 {
- pinctrl-0 = <&i2s0_bus>;
- pinctrl-names = "default";
- status = "okay";
};
sound {
@@ -902,17 +248,6 @@
"SPK", "SPKOUTRP";
};
- exynos-usbphy at 125B0000 {
- status = "okay";
- };
-
- hsotg at 12480000 {
- vusb_d-supply = <&ldo15_reg>;
- vusb_a-supply = <&ldo12_reg>;
- dr_mode = "peripheral";
- status = "okay";
- };
-
thermistor-ap at 0 {
compatible = "ntc,ncp15wb473";
pullup-uv = <1800000>; /* VCC_1.8V_AP */
@@ -945,6 +280,619 @@
};
};
+&adc {
+ vdd-supply = <&ldo3_reg>;
+ status = "okay";
+};
+
+&csis_0 {
+ status = "okay";
+ vddcore-supply = <&ldo8_reg>;
+ vddio-supply = <&ldo10_reg>;
+ assigned-clocks = <&clock CLK_MOUT_CSIS0>,
+ <&clock CLK_SCLK_CSIS0>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+
+ /* Camera C (3) MIPI CSI-2 (CSIS0) */
+ port at 3 {
+ reg = <3>;
+ csis0_ep: endpoint {
+ remote-endpoint = <&s5c73m3_ep>;
+ data-lanes = <1 2 3 4>;
+ samsung,csis-hs-settle = <12>;
+ };
+ };
+};
+
+&csis_1 {
+ status = "okay";
+ vddcore-supply = <&ldo8_reg>;
+ vddio-supply = <&ldo10_reg>;
+ assigned-clocks = <&clock CLK_MOUT_CSIS1>,
+ <&clock CLK_SCLK_CSIS1>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+
+ /* Camera D (4) MIPI CSI-2 (CSIS1) */
+ port at 4 {
+ reg = <4>;
+ csis1_ep: endpoint {
+ remote-endpoint = <&is_s5k6a3_ep>;
+ data-lanes = <1>;
+ samsung,csis-hs-settle = <18>;
+ samsung,csis-wclk;
+ };
+ };
+};
+
+&dsi_0 {
+ vddcore-supply = <&ldo8_reg>;
+ vddio-supply = <&ldo10_reg>;
+ samsung,pll-clock-frequency = <24000000>;
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 1 {
+ reg = <1>;
+
+ dsi_out: endpoint {
+ remote-endpoint = <&dsi_in>;
+ samsung,burst-clock-frequency = <500000000>;
+ samsung,esc-clock-frequency = <20000000>;
+ };
+ };
+ };
+
+ panel at 0 {
+ compatible = "samsung,s6e8aa0";
+ reg = <0>;
+ vdd3-supply = <&lcd_vdd3_reg>;
+ vci-supply = <&ldo25_reg>;
+ reset-gpios = <&gpy4 5 0>;
+ power-on-delay= <50>;
+ reset-delay = <100>;
+ init-delay = <100>;
+ flip-horizontal;
+ flip-vertical;
+ panel-width-mm = <58>;
+ panel-height-mm = <103>;
+
+ display-timings {
+ timing-0 {
+ clock-frequency = <0>;
+ hactive = <720>;
+ vactive = <1280>;
+ hfront-porch = <5>;
+ hback-porch = <5>;
+ hsync-len = <5>;
+ vfront-porch = <13>;
+ vback-porch = <1>;
+ vsync-len = <2>;
+ };
+ };
+
+ port {
+ dsi_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+ };
+};
+
+&exynos_usbphy {
+ status = "okay";
+};
+
+&fimc_0 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC0>,
+ <&clock CLK_SCLK_FIMC0>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
+
+&fimc_1 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC1>,
+ <&clock CLK_SCLK_FIMC1>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
+
+&fimc_2 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC2>,
+ <&clock CLK_SCLK_FIMC2>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
+
+&fimc_3 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC3>,
+ <&clock CLK_SCLK_FIMC3>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
+
+&fimc_is {
+ pinctrl-0 = <&fimc_is_uart>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ i2c1_isp: i2c-isp at 12140000 {
+ pinctrl-0 = <&fimc_is_i2c1>;
+ pinctrl-names = "default";
+
+ s5k6a3 at 10 {
+ compatible = "samsung,s5k6a3";
+ reg = <0x10>;
+ svdda-supply = <&cam_io_reg>;
+ svddio-supply = <&ldo19_reg>;
+ afvdd-supply = <&ldo19_reg>;
+ clock-frequency = <24000000>;
+ /* CAM_B_CLKOUT */
+ clocks = <&camera 1>;
+ clock-names = "extclk";
+ samsung,camclk-out = <1>;
+ gpios = <&gpm1 6 0>;
+
+ port {
+ is_s5k6a3_ep: endpoint {
+ remote-endpoint = <&csis1_ep>;
+ data-lanes = <1>;
+ };
+ };
+ };
+ };
+};
+
+&fimc_lite_0 {
+ status = "okay";
+};
+
+&fimc_lite_1 {
+ status = "okay";
+};
+
+&fimd {
+ status = "okay";
+};
+
+&hsotg {
+ vusb_d-supply = <&ldo15_reg>;
+ vusb_a-supply = <&ldo12_reg>;
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&i2c_0 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <400000>;
+ pinctrl-0 = <&i2c0_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ s5c73m3 at 3c {
+ compatible = "samsung,s5c73m3";
+ reg = <0x3c>;
+ standby-gpios = <&gpm0 1 1>; /* ISP_STANDBY */
+ xshutdown-gpios = <&gpf1 3 1>; /* ISP_RESET */
+ vdd-int-supply = <&buck9_reg>;
+ vddio-cis-supply = <&ldo9_reg>;
+ vdda-supply = <&ldo17_reg>;
+ vddio-host-supply = <&ldo18_reg>;
+ vdd-af-supply = <&cam_af_reg>;
+ vdd-reg-supply = <&cam_io_reg>;
+ clock-frequency = <24000000>;
+ /* CAM_A_CLKOUT */
+ clocks = <&camera 0>;
+ clock-names = "cis_extclk";
+ port {
+ s5c73m3_ep: endpoint {
+ remote-endpoint = <&csis0_ep>;
+ data-lanes = <1 2 3 4>;
+ };
+ };
+ };
+};
+
+&i2c_3 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <400000>;
+ pinctrl-0 = <&i2c3_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ mms114-touchscreen at 48 {
+ compatible = "melfas,mms114";
+ reg = <0x48>;
+ interrupt-parent = <&gpm2>;
+ interrupts = <3 2>;
+ x-size = <720>;
+ y-size = <1280>;
+ avdd-supply = <&ldo23_reg>;
+ vdd-supply = <&ldo24_reg>;
+ };
+};
+
+&i2c_4 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <100000>;
+ pinctrl-0 = <&i2c4_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ wm1811: wm1811 at 1a {
+ compatible = "wlf,wm1811";
+ reg = <0x1a>;
+ clocks = <&pmu_system_controller 0>;
+ clock-names = "MCLK1";
+ DCVDD-supply = <&ldo3_reg>;
+ DBVDD1-supply = <&ldo3_reg>;
+ wlf,ldo1ena = <&gpj0 4 0>;
+ };
+};
+
+&i2c_7 {
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <100000>;
+ pinctrl-0 = <&i2c7_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ max77686: max77686_pmic at 09 {
+ compatible = "maxim,max77686";
+ interrupt-parent = <&gpx0>;
+ interrupts = <7 0>;
+ reg = <0x09>;
+ #clock-cells = <1>;
+
+ voltage-regulators {
+ ldo1_reg: ldo1 {
+ regulator-compatible = "LDO1";
+ regulator-name = "VALIVE_1.0V_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-compatible = "LDO2";
+ regulator-name = "VM1M2_1.2V_AP";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo3_reg: ldo3 {
+ regulator-compatible = "LDO3";
+ regulator-name = "VCC_1.8V_AP";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: ldo4 {
+ regulator-compatible = "LDO4";
+ regulator-name = "VCC_2.8V_AP";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo5_reg: ldo5 {
+ regulator-compatible = "LDO5";
+ regulator-name = "VCC_1.8V_IO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: ldo6 {
+ regulator-compatible = "LDO6";
+ regulator-name = "VMPLL_1.0V_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo7_reg: ldo7 {
+ regulator-compatible = "LDO7";
+ regulator-name = "VPLL_1.0V_AP";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo8_reg: ldo8 {
+ regulator-compatible = "LDO8";
+ regulator-name = "VMIPI_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo9_reg: ldo9 {
+ regulator-compatible = "LDO9";
+ regulator-name = "CAM_ISP_MIPI_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo10_reg: ldo10 {
+ regulator-compatible = "LDO10";
+ regulator-name = "VMIPI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo11_reg: ldo11 {
+ regulator-compatible = "LDO11";
+ regulator-name = "VABB1_1.95V";
+ regulator-min-microvolt = <1950000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo12_reg: ldo12 {
+ regulator-compatible = "LDO12";
+ regulator-name = "VUOTG_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo13_reg: ldo13 {
+ regulator-compatible = "LDO13";
+ regulator-name = "NFC_AVDD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo14_reg: ldo14 {
+ regulator-compatible = "LDO14";
+ regulator-name = "VABB2_1.95V";
+ regulator-min-microvolt = <1950000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-always-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo15_reg: ldo15 {
+ regulator-compatible = "LDO15";
+ regulator-name = "VHSIC_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo16_reg: ldo16 {
+ regulator-compatible = "LDO16";
+ regulator-name = "VHSIC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo17_reg: ldo17 {
+ regulator-compatible = "LDO17";
+ regulator-name = "CAM_SENSOR_CORE_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo18_reg: ldo18 {
+ regulator-compatible = "LDO18";
+ regulator-name = "CAM_ISP_SEN_IO_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo19_reg: ldo19 {
+ regulator-compatible = "LDO19";
+ regulator-name = "VT_CAM_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo20_reg: ldo20 {
+ regulator-compatible = "LDO20";
+ regulator-name = "VDDQ_PRE_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo21_reg: ldo21 {
+ regulator-compatible = "LDO21";
+ regulator-name = "VTF_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ ldo22_reg: ldo22 {
+ regulator-compatible = "LDO22";
+ regulator-name = "VMEM_VDD_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ ldo23_reg: ldo23 {
+ regulator-compatible = "LDO23";
+ regulator-name = "TSP_AVDD_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo24_reg: ldo24 {
+ regulator-compatible = "LDO24";
+ regulator-name = "TSP_VDD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo25_reg: ldo25 {
+ regulator-compatible = "LDO25";
+ regulator-name = "LCD_VCC_3.3V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo26_reg: ldo26 {
+ regulator-compatible = "LDO26";
+ regulator-name = "MOTOR_VCC_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ buck1_reg: buck1 {
+ regulator-compatible = "BUCK1";
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck2_reg: buck2 {
+ regulator-compatible = "BUCK2";
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ buck3_reg: buck3 {
+ regulator-compatible = "BUCK3";
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck4_reg: buck4 {
+ regulator-compatible = "BUCK4";
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck5_reg: buck5 {
+ regulator-compatible = "BUCK5";
+ regulator-name = "VMEM_1.2V_AP";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ buck6_reg: buck6 {
+ regulator-compatible = "BUCK6";
+ regulator-name = "VCC_SUB_1.35V";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ };
+
+ buck7_reg: buck7 {
+ regulator-compatible = "BUCK7";
+ regulator-name = "VCC_SUB_2.0V";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: buck8 {
+ regulator-compatible = "BUCK8";
+ regulator-name = "VMEM_VDDF_3.0V";
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ buck9_reg: buck9 {
+ regulator-compatible = "BUCK9";
+ regulator-name = "CAM_ISP_CORE_1.2V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1200000>;
+ maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>;
+ };
+ };
+ };
+};
+
+&i2s0 {
+ pinctrl-0 = <&i2s0_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&mshc_0 {
+ num-slots = <1>;
+ broken-cd;
+ non-removable;
+ card-detect-delay = <200>;
+ vmmc-supply = <&ldo22_reg>;
+ clock-frequency = <400000000>;
+ samsung,dw-mshc-ciu-div = <0>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
+ pinctrl-names = "default";
+ status = "okay";
+ bus-width = <8>;
+ cap-mmc-highspeed;
+};
+
&pmu_system_controller {
assigned-clocks = <&pmu_system_controller 0>;
assigned-clock-parents = <&clock CLK_XUSBXTI>;
@@ -1306,8 +1254,62 @@
};
};
+&pwm {
+ pinctrl-0 = <&pwm0_out>;
+ pinctrl-names = "default";
+ samsung,pwm-outputs = <0>;
+ status = "okay";
+};
+
&rtc {
status = "okay";
clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
clock-names = "rtc", "rtc_src";
};
+
+&sdhci_2 {
+ bus-width = <4>;
+ cd-gpios = <&gpx3 4 0>;
+ cd-inverted;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
+ pinctrl-names = "default";
+ vmmc-supply = <&ldo21_reg>;
+ status = "okay";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
+
+&spi_1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_bus>;
+ cs-gpios = <&gpb 5 0>;
+ status = "okay";
+
+ s5c73m3_spi: s5c73m3 {
+ compatible = "samsung,s5c73m3";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ controller-data {
+ samsung,spi-feedback-delay = <2>;
+ };
+ };
+};
+
+&tmu {
+ vtmu-supply = <&ldo10_reg>;
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v4 12/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4412 Origen
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (10 preceding siblings ...)
2015-05-11 13:42 ` [PATCH v4 11/13] ARM: dts: exynos4: Use labels for overriding nodes in Trats2 Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
2015-05-11 13:42 ` [PATCH v4 13/13] ARM: dts: exynos4: Use labels for overriding nodes in Tiny4412 Krzysztof Kozlowski
12 siblings, 0 replies; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4412-origen.dts | 892 ++++++++++++++++----------------
1 file changed, 446 insertions(+), 446 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts
index bd8b73077d41..84c76310b312 100644
--- a/arch/arm/boot/dts/exynos4412-origen.dts
+++ b/arch/arm/boot/dts/exynos4412-origen.dts
@@ -50,485 +50,485 @@
};
};
- watchdog at 10060000 {
- status = "okay";
- };
-
- rtc at 10070000 {
- status = "okay";
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing {
+ clock-frequency = <47500000>;
+ hactive = <1024>;
+ vactive = <600>;
+ hfront-porch = <64>;
+ hback-porch = <16>;
+ hsync-len = <48>;
+ vback-porch = <64>;
+ vfront-porch = <16>;
+ vsync-len = <3>;
+ };
};
- pinctrl at 11000000 {
- keypad_rows: keypad-rows {
- samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
- samsung,pin-function = <3>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <0>;
};
- keypad_cols: keypad-cols {
- samsung,pins = "gpx1-0", "gpx1-1";
- samsung,pin-function = <3>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ xusbxti {
+ compatible = "samsung,clock-xusbxti";
+ clock-frequency = <24000000>;
};
};
+};
- keypad at 100A0000 {
- samsung,keypad-num-rows = <3>;
- samsung,keypad-num-columns = <2>;
- linux,keypad-no-autorepeat;
- linux,keypad-wakeup;
- pinctrl-0 = <&keypad_rows &keypad_cols>;
- pinctrl-names = "default";
- status = "okay";
-
- key_home {
- keypad,row = <0>;
- keypad,column = <0>;
- linux,code = <KEY_HOME>;
- };
+&fimd {
+ pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
+ pinctrl-names = "default";
+ status = "okay";
+};
- key_down {
- keypad,row = <0>;
- keypad,column = <1>;
- linux,code = <KEY_DOWN>;
- };
+&g2d {
+ status = "okay";
+};
- key_up {
- keypad,row = <1>;
- keypad,column = <0>;
- linux,code = <KEY_UP>;
- };
+&i2c_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <20000>;
+ pinctrl-0 = <&i2c0_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ s5m8767_pmic at 66 {
+ compatible = "samsung,s5m8767-pmic";
+ reg = <0x66>;
+
+ s5m8767,pmic-buck-default-dvs-idx = <3>;
+
+ s5m8767,pmic-buck-dvs-gpios = <&gpx2 3 0>,
+ <&gpx2 4 0>,
+ <&gpx2 5 0>;
+
+ s5m8767,pmic-buck-ds-gpios = <&gpm3 5 0>,
+ <&gpm3 6 0>,
+ <&gpm3 7 0>;
+
+ s5m8767,pmic-buck2-dvs-voltage = <1250000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>;
+
+ s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
+ <1100000>, <1100000>,
+ <1100000>, <1100000>,
+ <1100000>, <1100000>;
+
+ s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>;
+
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
- key_menu {
- keypad,row = <1>;
- keypad,column = <1>;
- linux,code = <KEY_MENU>;
- };
+ ldo2_reg: LDO2 {
+ regulator-name = "VDDQ_M12";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
- key_back {
- keypad,row = <2>;
- keypad,column = <0>;
- linux,code = <KEY_BACK>;
- };
+ ldo3_reg: LDO3 {
+ regulator-name = "VDDIOAP_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VDDQ_PRE";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "VDD18_2M";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD10_MPLL";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD10_XPLL";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VDD10_MIPI";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "VDD33_LCD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "VDD18_MIPI";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD18_ABB1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD33_UOTG";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "VDDIOPERI_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "VDD18_ABB02";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "VDD10_USH";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "VDD18_HSIC";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "VDDIOAP_MMC012_28";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo18_reg: LDO18 {
+ regulator-name = "VDDIOPERI_28";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo19_reg: LDO19 {
+ regulator-name = "DVDD25";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo20_reg: LDO20 {
+ regulator-name = "VDD28_CAM";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo21_reg: LDO21 {
+ regulator-name = "VDD28_AF";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo22_reg: LDO22 {
+ regulator-name = "VDDA28_2M";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
- key_enter {
- keypad,row = <2>;
- keypad,column = <1>;
- linux,code = <KEY_ENTER>;
+ ldo23_reg: LDO23 {
+ regulator-name = "VDD28_TF";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo24_reg: LDO24 {
+ regulator-name = "VDD33_A31";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo25_reg: LDO25 {
+ regulator-name = "VDD18_CAM";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo26_reg: LDO26 {
+ regulator-name = "VDD18_A31";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo27_reg: LDO27 {
+ regulator-name = "GPS_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ ldo28_reg: LDO28 {
+ regulator-name = "DVDD12";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "vdd_m12";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "vdd12_5m";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
+
+ buck9_reg: BUCK9 {
+ regulator-name = "vddf28_emmc";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>; /* Normal Mode */
+ };
};
};
+};
- g2d at 10800000 {
- status = "okay";
+&keypad {
+ samsung,keypad-num-rows = <3>;
+ samsung,keypad-num-columns = <2>;
+ linux,keypad-no-autorepeat;
+ linux,keypad-wakeup;
+ pinctrl-0 = <&keypad_rows &keypad_cols>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ key_home {
+ keypad,row = <0>;
+ keypad,column = <0>;
+ linux,code = <KEY_HOME>;
};
- sdhci at 12530000 {
- bus-width = <4>;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
- pinctrl-names = "default";
- vmmc-supply = <&mmc_reg>;
- status = "okay";
+ key_down {
+ keypad,row = <0>;
+ keypad,column = <1>;
+ linux,code = <KEY_DOWN>;
};
- mmc at 12550000 {
- pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
- pinctrl-names = "default";
- status = "okay";
-
- num-slots = <1>;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- bus-width = <8>;
- cap-mmc-highspeed;
+ key_up {
+ keypad,row = <1>;
+ keypad,column = <0>;
+ linux,code = <KEY_UP>;
};
- codec at 13400000 {
- samsung,mfc-r = <0x43000000 0x800000>;
- samsung,mfc-l = <0x51000000 0x800000>;
- status = "okay";
+ key_menu {
+ keypad,row = <1>;
+ keypad,column = <1>;
+ linux,code = <KEY_MENU>;
};
- fimd at 11c00000 {
- pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
- pinctrl-names = "default";
- status = "okay";
+ key_back {
+ keypad,row = <2>;
+ keypad,column = <0>;
+ linux,code = <KEY_BACK>;
};
- display-timings {
- native-mode = <&timing0>;
- timing0: timing {
- clock-frequency = <47500000>;
- hactive = <1024>;
- vactive = <600>;
- hfront-porch = <64>;
- hback-porch = <16>;
- hsync-len = <48>;
- vback-porch = <64>;
- vfront-porch = <16>;
- vsync-len = <3>;
- };
+ key_enter {
+ keypad,row = <2>;
+ keypad,column = <1>;
+ linux,code = <KEY_ENTER>;
};
+};
- serial at 13800000 {
- status = "okay";
- };
+&mfc {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+ status = "okay";
+};
- serial at 13810000 {
- status = "okay";
- };
+&mshc_0 {
+ pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ num-slots = <1>;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+};
- serial at 13820000 {
- status = "okay";
+&pinctrl_1 {
+ keypad_rows: keypad-rows {
+ samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
};
- serial at 13830000 {
- status = "okay";
+ keypad_cols: keypad-cols {
+ samsung,pins = "gpx1-0", "gpx1-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
};
+};
- i2c at 13860000 {
- #address-cells = <1>;
- #size-cells = <0>;
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <20000>;
- pinctrl-0 = <&i2c0_bus>;
- pinctrl-names = "default";
- status = "okay";
-
- s5m8767_pmic at 66 {
- compatible = "samsung,s5m8767-pmic";
- reg = <0x66>;
-
- s5m8767,pmic-buck-default-dvs-idx = <3>;
-
- s5m8767,pmic-buck-dvs-gpios = <&gpx2 3 0>,
- <&gpx2 4 0>,
- <&gpx2 5 0>;
-
- s5m8767,pmic-buck-ds-gpios = <&gpm3 5 0>,
- <&gpm3 6 0>,
- <&gpm3 7 0>;
-
- s5m8767,pmic-buck2-dvs-voltage = <1250000>, <1200000>,
- <1200000>, <1200000>,
- <1200000>, <1200000>,
- <1200000>, <1200000>;
-
- s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
- <1100000>, <1100000>,
- <1100000>, <1100000>,
- <1100000>, <1100000>;
-
- s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
- <1200000>, <1200000>,
- <1200000>, <1200000>,
- <1200000>, <1200000>;
-
- regulators {
- ldo1_reg: LDO1 {
- regulator-name = "VDD_ALIVE";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- regulator-boot-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo2_reg: LDO2 {
- regulator-name = "VDDQ_M12";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo3_reg: LDO3 {
- regulator-name = "VDDIOAP_18";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo4_reg: LDO4 {
- regulator-name = "VDDQ_PRE";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo5_reg: LDO5 {
- regulator-name = "VDD18_2M";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo6_reg: LDO6 {
- regulator-name = "VDD10_MPLL";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo7_reg: LDO7 {
- regulator-name = "VDD10_XPLL";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo8_reg: LDO8 {
- regulator-name = "VDD10_MIPI";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo9_reg: LDO9 {
- regulator-name = "VDD33_LCD";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo10_reg: LDO10 {
- regulator-name = "VDD18_MIPI";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo11_reg: LDO11 {
- regulator-name = "VDD18_ABB1";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo12_reg: LDO12 {
- regulator-name = "VDD33_UOTG";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo13_reg: LDO13 {
- regulator-name = "VDDIOPERI_18";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo14_reg: LDO14 {
- regulator-name = "VDD18_ABB02";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo15_reg: LDO15 {
- regulator-name = "VDD10_USH";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo16_reg: LDO16 {
- regulator-name = "VDD18_HSIC";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo17_reg: LDO17 {
- regulator-name = "VDDIOAP_MMC012_28";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo18_reg: LDO18 {
- regulator-name = "VDDIOPERI_28";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo19_reg: LDO19 {
- regulator-name = "DVDD25";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2500000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo20_reg: LDO20 {
- regulator-name = "VDD28_CAM";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo21_reg: LDO21 {
- regulator-name = "VDD28_AF";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo22_reg: LDO22 {
- regulator-name = "VDDA28_2M";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo23_reg: LDO23 {
- regulator-name = "VDD28_TF";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo24_reg: LDO24 {
- regulator-name = "VDD33_A31";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo25_reg: LDO25 {
- regulator-name = "VDD18_CAM";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo26_reg: LDO26 {
- regulator-name = "VDD18_A31";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo27_reg: LDO27 {
- regulator-name = "GPS_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- ldo28_reg: LDO28 {
- regulator-name = "DVDD12";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- buck1_reg: BUCK1 {
- regulator-name = "vdd_mif";
- regulator-min-microvolt = <950000>;
- regulator-max-microvolt = <1100000>;
- regulator-always-on;
- regulator-boot-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- buck3_reg: BUCK3 {
- regulator-name = "vdd_int";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-boot-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- buck4_reg: BUCK4 {
- regulator-name = "vdd_g3d";
- regulator-min-microvolt = <750000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- buck5_reg: BUCK5 {
- regulator-name = "vdd_m12";
- regulator-min-microvolt = <750000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- buck6_reg: BUCK6 {
- regulator-name = "vdd12_5m";
- regulator-min-microvolt = <750000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- op_mode = <1>; /* Normal Mode */
- };
-
- buck9_reg: BUCK9 {
- regulator-name = "vddf28_emmc";
- regulator-min-microvolt = <750000>;
- regulator-max-microvolt = <3000000>;
- regulator-always-on;
- regulator-boot-on;
- op_mode = <1>; /* Normal Mode */
- };
- };
- };
- };
+&rtc {
+ status = "okay";
+};
- fixed-rate-clocks {
- xxti {
- compatible = "samsung,clock-xxti";
- clock-frequency = <0>;
- };
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
+ pinctrl-names = "default";
+ vmmc-supply = <&mmc_reg>;
+ status = "okay";
+};
- xusbxti {
- compatible = "samsung,clock-xusbxti";
- clock-frequency = <24000000>;
- };
- };
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCH v4 13/13] ARM: dts: exynos4: Use labels for overriding nodes in Tiny4412
2015-05-11 13:42 [PATCH v4 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
` (11 preceding siblings ...)
2015-05-11 13:42 ` [PATCH v4 12/13] ARM: dts: exynos4: Use labels for overriding nodes in Exynos4412 Origen Krzysztof Kozlowski
@ 2015-05-11 13:42 ` Krzysztof Kozlowski
12 siblings, 0 replies; 21+ messages in thread
From: Krzysztof Kozlowski @ 2015-05-11 13:42 UTC (permalink / raw)
To: linux-arm-kernel
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
---
arch/arm/boot/dts/exynos4412-tiny4412.dts | 54 +++++++++++++++----------------
1 file changed, 27 insertions(+), 27 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412-tiny4412.dts b/arch/arm/boot/dts/exynos4412-tiny4412.dts
index d46fd4c2aeaa..525684ca8dc0 100644
--- a/arch/arm/boot/dts/exynos4412-tiny4412.dts
+++ b/arch/arm/boot/dts/exynos4412-tiny4412.dts
@@ -56,33 +56,6 @@
};
};
- rtc at 10070000 {
- status = "okay";
- };
-
- sdhci at 12530000 {
- bus-width = <4>;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
- pinctrl-names = "default";
- status = "okay";
- };
-
- serial at 13800000 {
- status = "okay";
- };
-
- serial at 13810000 {
- status = "okay";
- };
-
- serial at 13820000 {
- status = "okay";
- };
-
- serial at 13830000 {
- status = "okay";
- };
-
fixed-rate-clocks {
xxti {
compatible = "samsung,clock-xxti";
@@ -95,3 +68,30 @@
};
};
};
+
+&rtc {
+ status = "okay";
+};
+
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread