From mboxrd@z Thu Jan  1 00:00:00 1970
From: jchandra@broadcom.com (Jayachandran C.)
Date: Tue, 12 May 2015 05:37:47 +0530
Subject: [PATCH v2 1/2] PCI: generic: remove dependency on hw_pci
In-Reply-To: <20150505155346.GJ1550@arm.com>
References: <1430791333-26013-1-git-send-email-jchandra@broadcom.com>
 <20150505155346.GJ1550@arm.com>
Message-ID: <20150512000746.GA31418@jayachandranc.netlogicmicro.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

On Tue, May 05, 2015 at 04:53:46PM +0100, Will Deacon wrote:
> On Tue, May 05, 2015 at 03:02:12AM +0100, Jayachandran C wrote:
> > The current code in pci-host-generic.c uses pci_common_init_dev()
> > from the arch/arm/ to do a part of the PCI initialization, and this
> > prevents it from being used on arm64.
> > 
> > The initialization done by pci_common_init_dev() that is really
> > needed by pci-host-generic.c can be done in the same file without
> > using the hw_pci API of ARM.
> > 
> > The ARM platform requires a pci_sys_data as sysdata for the PCI bus,
> > this is be handled by setting up 'struct gen_pci' to embed a
> > pci_sys_data variable as the first element on the ARM platform.
> > 
> > Signed-off-by: Jayachandran C <jchandra@broadcom.com>
> > ---
> > Here's v2 of the patches, this enables use of pci-host-generic on
> > arm64.
> > 
> > This has been tested on both qemu and fast model for arm64, and on
> > qemu for arm32.
> > 
> > v1->v2
> >  - Address comments from Arnd Bergmann and Lorenzo Pieralisi
> >     - move contents of gen_pci_init to gen_pci_probe
> >     - assign resources only when !probe_only
> >  - tested on ARM32 with qemu option -M virt
> 
> I tried this with an arm64 kernel running under kvmtool, but I get the
> following errors (a 32-bit ARM kernel does seem to work):
> 
>   PCI host bridge /pci ranges:
>      IO 0x00000000..0x0000ffff -> 0x00000000
>     MEM 0x41000000..0x7fffffff -> 0x41000000
>   pci-host-generic 40000000.pci: PCI host bridge to bus 0000:00
>   pci_bus 0000:00: root bus resource [bus 00-01]
>   pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
>   pci_bus 0000:00: root bus resource [mem 0x41000000-0x7fffffff]
>   pci_bus 0000:00: scanning bus
>   pci 0000:00:00.0: [1af4:1009] type 00 class 0xff0000
>   pci 0000:00:00.0: reg 0x10: [mem 0x41000000-0x410003ff]
>   pci 0000:00:00.0: reg 0x14: [io  0x6200-0x65ff]
>   pci 0000:00:00.0: reg 0x18: [mem 0x41000400-0x410005ff]
>   pci 0000:00:01.0: [1af4:1009] type 00 class 0xff0000
>   pci 0000:00:01.0: reg 0x10: [mem 0x41000800-0x41000bff]
>   pci 0000:00:01.0: reg 0x14: [io  0x6600-0x69ff]
>   pci 0000:00:01.0: reg 0x18: [mem 0x41000c00-0x41000dff]
>   pci_bus 0000:00: fixups for bus
>   pci_bus 0000:00: bus scan returning with max=00
>   pci 0000:00:00.0: fixup irq: got 10
>   pci 0000:00:00.0: assigning IRQ 10
>   pci 0000:00:01.0: fixup irq: got 11
>   pci 0000:00:01.0: assigning IRQ 11
>   virtio-pci 0000:00:00.0: can't enable device: BAR 0 [mem 0x41000000-0x410003ff] not claimed
>   virtio-pci: probe of 0000:00:00.0 failed with error -22
>   virtio-pci 0000:00:01.0: can't enable device: BAR 0 [mem 0x41000800-0x41000bff] not claimed
>   virtio-pci: probe of 0000:00:01.0 failed with error -22

PCI_PROBE_ONLY does not work yet for arm64, this will need further changes
in either arm64 or pci as noted by Lorenzo. This is not due to a problem with
this patch per se.

More importantly, this does not change the current arm32 behavior and adds
support for arm64 for two very useful cases
 - we can use "pci-host-ecam-generic" for a host bridge controller that is
   initialized by firmware, without adding a custom driver.
 - qemu virt platform works on arm64

If you think there are any furhter changes needed in this patchset please
let me know.

Thanks,
JC.