[PATCH 1/8] clk: sunxi: factors: Add m_start parameters

[maxime.ripard@free-electrons.com (Maxime Ripard)]

On Fri, May 15, 2015 at 05:11:16PM +0800, Chen-Yu Tsai wrote:
> On Fri, May 15, 2015 at 4:05 PM, Maxime Ripard
> <maxime.ripard@free-electrons.com> wrote:
> > On Fri, May 15, 2015 at 03:48:38PM +0800, Chen-Yu Tsai wrote:
> >> On Fri, May 15, 2015 at 3:43 PM, Maxime Ripard
> >> <maxime.ripard@free-electrons.com> wrote:
> >> > On Thu, May 14, 2015 at 05:12:07PM +0800, Chen-Yu Tsai wrote:
> >> >> On Sat, May 2, 2015 at 7:24 PM, Maxime Ripard
> >> >> <maxime.ripard@free-electrons.com> wrote:
> >> >> > Some clocks start incrementing the m factor at 0. Add a parameter to handle
> >> >> > it just like we did for the N factor.
> >> >> >
> >> >> > Since the behaviour until now was to assume that the m factor was starting
> >> >> > at 1, we also need to fix the other users.
> >> >> >
> >> >> > Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> >> >> > ---
> >> >> >  drivers/clk/sunxi/clk-factors.c    | 11 ++++++++++-
> >> >> >  drivers/clk/sunxi/clk-factors.h    |  2 ++
> >> >> >  drivers/clk/sunxi/clk-mod0.c       |  2 ++
> >> >> >  drivers/clk/sunxi/clk-sun8i-mbus.c |  2 ++
> >> >> >  drivers/clk/sunxi/clk-sun9i-core.c |  6 ++++++
> >> >> >  drivers/clk/sunxi/clk-sunxi.c      | 10 ++++++++++
> >> >> >  6 files changed, 32 insertions(+), 1 deletion(-)
> >> >> >
> >> >> > diff --git a/drivers/clk/sunxi/clk-factors.c b/drivers/clk/sunxi/clk-factors.c
> >> >> > index 8c20190a3e9f..100a711c3e3d 100644
> >> >> > --- a/drivers/clk/sunxi/clk-factors.c
> >> >> > +++ b/drivers/clk/sunxi/clk-factors.c
> >> >> > @@ -56,15 +56,24 @@ static unsigned long clk_factors_recalc_rate(struct clk_hw *hw,
> >> >> >         /* Get each individual factor if applicable */
> >> >> >         if (config->nwidth != SUNXI_FACTORS_NOT_APPLICABLE)
> >> >> >                 n = FACTOR_GET(config->nshift, config->nwidth, reg);
> >> >> > +
> >> >> >         if (config->kwidth != SUNXI_FACTORS_NOT_APPLICABLE)
> >> >> >                 k = FACTOR_GET(config->kshift, config->kwidth, reg);
> >> >> > +
> >> >> >         if (config->mwidth != SUNXI_FACTORS_NOT_APPLICABLE)
> >> >> >                 m = FACTOR_GET(config->mshift, config->mwidth, reg);
> >> >> > +       else
> >> >> > +               /* Make sure we don't get a division by zero */
> >> >> > +               m = 1;
> >> >>
> >> >> What happens when mwidth is valid, m_start = 0, and m = 0?
> >> >
> >> > That's a very good question. A division by zero in the kernel, I'd
> >> > say.
> >> >
> >> > But I don't think we can end up in such a case today, and it's
> >> > somewhat expected that it will happen, and no clock have looked at can
> >> > actually end up in such a case.
> >>
> >> It's possible if the bootloader left the clock in an invalid state.
> >> How about just returning 0, indicating an invalid rate, early?
> >
> > The value set in the register might be zero, but that will always
> > really mean 1, either through m_start or m_zero. That would be a bug
> > in the driver itself.
> 
> Maybe you should switch the order of these 2 patches to make it clear?
> Or maybe squash them? As it currently is, m_start = 0 and m = 0 with
> this patch only is a bug.

We don't have any clock with m_start = 0 at this point. All the clocks
have m_start = 1, which is safe.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150515/69274997/attachment-0001.sig>