[PATCH-V5 3/4] mfd: 88pm800: Set default interrupt clear method

[lee.jones@linaro.org (Lee Jones)]

On Tue, 07 Jul 2015, Vaibhav Hiremath wrote:

> 
> 
> On Tuesday 07 July 2015 06:24 PM, Lee Jones wrote:
> >On Tue, 07 Jul 2015, Vaibhav Hiremath wrote:
> >
> >>
> >>
> >>On Tuesday 07 July 2015 04:48 PM, Vaibhav Hiremath wrote:
> >>>
> >>>
> >>>On Tuesday 07 July 2015 04:42 PM, Lee Jones wrote:
> >>>>On Tue, 07 Jul 2015, Vaibhav Hiremath wrote:
> >>>>>On Tuesday 07 July 2015 04:10 PM, Lee Jones wrote:
> >>>>>>On Tue, 07 Jul 2015, Vaibhav Hiremath wrote:
> >>>>>>>On Tuesday 07 July 2015 12:59 PM, Lee Jones wrote:
> >>>>>>>>On Mon, 29 Jun 2015, Vaibhav Hiremath wrote:
> >>>>>>>>
> >>>>>>>>>As per the spec, bit 1 (INT_CLEAR_MODE) of reg addr 0xe
> >>>>>>>>>(page 0) controls the method of clearing interrupt
> >>>>>>>>>status of 88pm800 family of devices;
> >>>>>>>>>
> >>>>>>>>>   0: clear on read
> >>>>>>>>>   1: clear on write
> >>>>>>>>>
> >>>>>>>>>If pdata is not coming from board file, then set the
> >>>>>>>>>default irq clear method to "irq clear on write"
> >>>>>>>>>
> >>>>>>>>>Also, as suggested by "Lee Jones" renaming variable field
> >>>>>>>>>to appropriate name.
> >>>>>>>>>
> >>>>>>>>>Signed-off-by: Zhao Ye <zhaoy@marvell.com>
> >>>>>>>>>Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
> >>>>>>>>>---
> >>>>>>>>>  drivers/mfd/88pm800.c       | 15 ++++++++++-----
> >>>>>>>>>  include/linux/mfd/88pm80x.h | 10 ++++++++--
> >>>>>>>>>  2 files changed, 18 insertions(+), 7 deletions(-)
> >>>>>>>>>
> 
> <snip>
> 
> >>>
> >>>Yes certainly, this is another option (rather preferred one).
> >>>
> >>>But to be consistent with other's I proposed this, please refer to the
> >>>fn device_800_init(), where all xxx_init() are taking 2 arguments, and
> >>>second argument is pdata.
> >>>
> >>>
> >>>There is room for cleanup, I agree.
> >>>I can put this too in the next cleanup series.
> >>>
> >>
> >>Note that this is init function, called from probe.
> >>
> >>So both approach looks ok to me.
> >
> >Please clean up the other.  Function and put it at the front of the
> >set when you re-submit.
> >
> 
> Sorry for dumb question here :)
> I did not understand what do you mean by "in front of the set"?
> 
> You want to see all the patches into one single series?
> Or
> have separate series,
> 	1. existing DT addition series
> 	2. new clean-up series

[PATCH v6 0/5] mfd: 88pm800: Add Device tree support
?>[PATCH v6 1/5] mfd: 88pm800: Obtain pdata from 'device' rather than passing as parameter
?>[PATCH v6 2/5] mfd: 88pm800: Add device tree support
?>[PATCH v6 3/5] mfd: 88pm800: Remove unnecessary protection around pdata
?>[PATCH v6 4/5] mfd: 88pm800: Set default interrupt clear method
?>[PATCH v6 5/5] mfd: devicetree: bindings: Add new 88pm800 mfd binding

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog