[PATCH v3 3/3] dt-binding:Documents the mbigen bindings

[mark.rutland@arm.com (Mark Rutland)]

> >> +The mbigen and devices connect to mbigen have the following properties:
> >> +
> >> +
> >> +Mbigen required properties:
> >> +-------------------------------------------
> >> +-compatible: Should be "hisilicon,mbigen-v2"
> >> +-msi-parent: should specified the ITS mbigen connected
> >> +-interrupt controller: Identifies the node as an interrupt controller
> >> +- #interrupt-cells : Specifies the number of cells needed to encode an
> >> +  interrupt source. The value is 5 now.
> >> +
> >> +  The 1st cell is the device id.
> > 
> > Does a given mbigen block generate interrupts with different ITS device
> > IDs? Or does a given mbigen block have a single device ID shared by all
> > interrupts it generates?
> > 
> The mbigen chip structrue likes below:
> 
> 			mbigen_chip(domain)
> 	|------------|------------------|
> mbigen_node0	mbigen_node1		mbigen_node2
> |	|	|	|		|	|
> dev1	dev2	dev3	dev4		dev5	dev6
> 
> For each mbigen chip, it contains several mbigen nodes.
> For each mbigen node, it can collect interrupts from different devices.
> 
> For example, dev1 and dev2 both connect to mbigen node0.Because dev1 and dev2 are
> differnt device, they have different device id.
> 
> The device id is encoded in mbigen chip and can not be changed.

Thanks for the diagram, that clears up some of my confusion regarding
nodes.

Ok, so each device has it's own device ID. That's good. If a device has
multiple interrupt lines to the mbigen, do these always share the same
device ID?

> >> +  The 2nd cell is the totall interrupt number of this device?
> > 
> > I don't follow. What is a "total interrupt number"?
> > 
> It's the wired interrupt number connected to a device.
> For the devices connected to mbigen node, the interrupt number  varied from
> 1 to 100+ .So I have to specifies this value in dts.
>
> >> +  The 3rd cell is the hardware pin number of the interrupt.
> >> +  This value depends on the Soc design.
> > 
> > This property seems sane.
> > 
> >> +  The 4th cell is the mbigen node number. This value should refer to the
> >> +  vendor soc specification.
> > 
> > What is this, and why do you think you need it?
> > 
> > Surely the address of the mbigen node is a sufficient unique identifier?
> > 
> 		mbigen_chip(domain)
> 	|------------|------------------|
> mbigen_node0	mbigen_node1		mbigen_node2
> |	|	|	|		|	|
> dev1	dev2	dev3	dev4		dev5	dev6
> 
> To avoid the duplicat hardware irq number problem, the Mbigen node number is defined here.
> For example:
> dev1 has 3 interrupts with pin number from 0 to 2
> dev3 has 5 interrupts with pin number from 0 to 4
> For dev3 the interrupt from 0 to 2 would be has same hardware irq number
> as dev1 if we only use pin number.
>
> Because these two devices located in same irq domain(mbigen chip),using same
> hwirq number is a mistake.
> 
> In mbigen driver, I will use this value and  the 3rd cell(pin number) to compose
> a new hardware irq( (nid<<8) | pin number) for mbigen using.

Ok. I now see why you need node and pin.

However, I don't see why you also need the 'total' interrupt number. Why
isn't node and pin sufficient to uniquely identify an interrupt?

Thanks,
Mark.