[PATCH 08/11] MTD: m25p80: Add option to limit SPI transfer size.

[marex@denx.de (Marek Vasut)]

On Wednesday, July 22, 2015 at 10:18:04 AM, Michal Suchanek wrote:
> On 22 July 2015 at 09:58, Marek Vasut <marex@denx.de> wrote:
> > On Wednesday, July 22, 2015 at 09:45:27 AM, Michal Suchanek wrote:
> >> On 22 July 2015 at 09:33, Marek Vasut <marex@denx.de> wrote:
> >> > On Wednesday, July 22, 2015 at 09:30:54 AM, Michal Suchanek wrote:
> >> >> On 22 July 2015 at 06:49, Vinod Koul <vinod.koul@intel.com> wrote:
> >> >> > On Tue, Jul 21, 2015 at 10:14:11AM +0200, Michal Suchanek wrote:
> >> >> >> > Or alternatively we could publish the limitations of the channel
> >> >> >> > using capabilities so SPI knows I have a dmaengine channel and
> >> >> >> > it can transfer max N length transfers so would be able to
> >> >> >> > break rather than guessing it or coding in DT. Yes it may come
> >> >> >> > from DT but that should be dmaengine driver rather than client
> >> >> >> > driver :)
> >> >> >> > 
> >> >> >> > This can be done by dma_get_slave_caps(chan, &caps)
> >> >> >> > 
> >> >> >> > And we add max_length as one more parameter to existing set
> >> >> >> > 
> >> >> >> > Also all this could be handled in generic SPI-dmaengine layer so
> >> >> >> > that individual drivers don't have to code it in
> >> >> >> > 
> >> >> >> > Let me know if this idea is okay, I can push the dmaengine
> >> >> >> > bits...
> >> >> >> 
> >> >> >> It would be ok if there was a fixed limit. However, the limit
> >> >> >> depends on SPI slave settings. Presumably for other buses using
> >> >> >> the dmaengine the limit would depend on the bus or slave settings
> >> >> >> as well. I do not see a sane way of passing this all the way to
> >> >> >> the dmaengine driver.
> >> >> > 
> >> >> > I don't see why this should be client (SPI) dependent. The max
> >> >> > length supported is a dmaengine constraint, typically flowing from
> >> >> > max blocks/length it can transfer. Know this limit can allow
> >> >> > clients to split transfers.
> >> >> 
> >> >> In practice on the board I have the maximum transfer length before it
> >> >> fails depends on SPI bus speed which is set up per slave. I did not
> >> >> try searching the space of possible settings thorougly and settled
> >> >> for a setting that gives reasonable speed and transfer length.
> >> > 
> >> > This looks more like a signal integrity issue though.
> >> 
> >> It certainly does on the surface. However, when wrong data is
> >> delivered over the SPI bus (such as when I use wrong phase setting)
> >> the SPI controller happily delivers wrong data over PIO.
> >> 
> >> The failure I am seeing is that the pl330 DMA program which repeatedly
> >> waits for data from the SPI controller never finishes the read loop
> >> and does not signal the interrupt. It seems it also leaves some data
> >> in a FIFO somewhere so next command on the flash returns garbage and
> >> fails.
> > 
> > I observed something similar on MXS (mx28) SPI block. Do you use mixed
> > PIO/DMA mode perhaps ?
> 
> The SPI driver uses PIO for short transfers and DMA for transfers
> longer than the controller FIFO. This seems to be the standard way to
> do things.It works flawlessly so long as submitting overly long DMA
> programs is avoided.

Can you try doing JUST DMA, no PIO ? I remember seeing some bus synchronisation
issues when I did mixed PIO/DMA on the MXS and it was nasty to track down. Just
give pure DMA a go to see if the thing stabilizes somehow.

> > Do you have the option to connect a bus analyzer?
> > I can probably offer you some tools, I'm in Prague ...
> 
> The flash chip is accessible when removing the bottom cover. It is
> VSOP8 package slightly lower than SOP8 so attaching clips to it might
> be a bit problematic. That's the only accessible part. Everything
> other than SPI is inside the SoC.

That might be doable, though you might want to try the above thing first.

> Since SPI has no verification whatsoever the chip might be completely
> dead and you can still read fine all zeroes or all ones when
> attempting a read from it. I observed this behaviour when I used a
> flash chip in a socket and it was not firmly seated. It was with a
> different SPI controller, though.

You should run into issues as soon as the SPI NOR framework tries to read
status register, no ?