[PATCH v3 0/4] Add fec1 and fec2 support for i.MX7d sdb board

[PATCH v3 0/4] Add fec1 and fec2 support for i.MX7d sdb board

[Fugang Duan]

The patch series is to add fec support for i.MX7d sdb board. Since i.MX7d fec ip is
the same as i.MX6SX, so there have no change for driver itself.

Patch#1: add new iomux-gpr file to define iomux-gpr register and field for i.MX7d.
Patch#2: i.MX7d sdb board install bcm54220 phy, i.MX7d arm2 board install AR8031 phy.
         For the two phys, there needs extra phy setting, so package the setting to fixup.
Patch#3~4: Add fec dts node and pinmux setting in dts file.


Since the patch series drop i.MX7d pinfunc patch, and also depend on the pinfunc patch. So
pls apply the patch series after Adrian's patch: http://article.gmane.org/gmane.linux.kernel.gpio/10398/match=

Change:
V3:
	* Drop patch "ARM: dts: imx: pinfunc: add GPIO1 pin define for i.MX7d" that was also submitted by
	  Adrian: http://article.gmane.org/gmane.linux.kernel.gpio/10398/match=
	* Modify some slice as Shawn's comments.
V2:
        * Remove patch#1 in V1 patch series. Move the sigle BCM54220 PHY ID define to machine file.
        * The current BCM54220 switch phy still use generic phy driver since broadcom phy driver don't
          support the switch phy, there need effort to add the switch phy support. Once broadcom phy driver
          will support the bcm54220 switch phy, we can add the special config to imx_v6_v7_defconfig.


Fugang Duan (4):
  ARM: imx7d: add imx7d iomux-gpr field define
  ARM: imx: add enet init for i.MX7D platform
  ARM: dts: imx7d: add fec1 and fec2 support for i.MX7d soc
  ARM: dts: imx7d-sdb: add fec1 and fec2 support

 arch/arm/boot/dts/imx7d-sdb.dts            | 76 +++++++++++++++++++++++++++++-
 arch/arm/boot/dts/imx7d.dtsi               | 36 ++++++++++++++
 arch/arm/mach-imx/mach-imx7d.c             | 74 +++++++++++++++++++++++++++++
 include/linux/mfd/syscon/imx7-iomuxc-gpr.h | 47 ++++++++++++++++++
 4 files changed, 232 insertions(+), 1 deletion(-)
 create mode 100644 include/linux/mfd/syscon/imx7-iomuxc-gpr.h

-- 
1.9.1

[PATCH v3 1/4] ARM: imx7d: add imx7d iomux-gpr field define

[Fugang Duan]

Add imx7d iomux-gpr field define.

Signed-off-by: Fugang Duan <B38611@freescale.com>
---
 include/linux/mfd/syscon/imx7-iomuxc-gpr.h | 47 ++++++++++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/include/linux/mfd/syscon/imx7-iomuxc-gpr.h b/include/linux/mfd/syscon/imx7-iomuxc-gpr.h
new file mode 100644
index 0000000..4585d61
--- /dev/null
+++ b/include/linux/mfd/syscon/imx7-iomuxc-gpr.h
@@ -0,0 +1,47 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __LINUX_IMX7_IOMUXC_GPR_H
+#define __LINUX_IMX7_IOMUXC_GPR_H
+
+#define IOMUXC_GPR0	0x00
+#define IOMUXC_GPR1	0x04
+#define IOMUXC_GPR2	0x08
+#define IOMUXC_GPR3	0x0c
+#define IOMUXC_GPR4	0x10
+#define IOMUXC_GPR5	0x14
+#define IOMUXC_GPR6	0x18
+#define IOMUXC_GPR7	0x1c
+#define IOMUXC_GPR8	0x20
+#define IOMUXC_GPR9	0x24
+#define IOMUXC_GPR10	0x28
+#define IOMUXC_GPR11	0x2c
+#define IOMUXC_GPR12	0x30
+#define IOMUXC_GPR13	0x34
+#define IOMUXC_GPR14	0x38
+#define IOMUXC_GPR15	0x3c
+#define IOMUXC_GPR16	0x40
+#define IOMUXC_GPR17	0x44
+#define IOMUXC_GPR18	0x48
+#define IOMUXC_GPR19	0x4c
+#define IOMUXC_GPR20	0x50
+#define IOMUXC_GPR21	0x54
+#define IOMUXC_GPR22	0x58
+
+/* For imx7d iomux gpr register field define */
+#define IMX7D_GPR1_IRQ_MASK			(0x1 << 12)
+#define IMX7D_GPR1_ENET1_TX_CLK_SEL_MASK	(0x1 << 13)
+#define IMX7D_GPR1_ENET2_TX_CLK_SEL_MASK	(0x1 << 14)
+#define IMX7D_GPR1_ENET_TX_CLK_SEL_MASK		(0x3 << 13)
+#define IMX7D_GPR1_ENET1_CLK_DIR_MASK		(0x1 << 17)
+#define IMX7D_GPR1_ENET2_CLK_DIR_MASK		(0x1 << 18)
+#define IMX7D_GPR1_ENET_CLK_DIR_MASK		(0x3 << 17)
+
+#define IMX7D_GPR5_CSI_MUX_CONTROL_MIPI		(0x1 << 4)
+
+#endif /* __LINUX_IMX7_IOMUXC_GPR_H */
-- 
1.9.1

[PATCH v3 2/4] ARM: imx: add enet init for i.MX7D platform

[Fugang Duan]

Add enet phy fixup, clock source init for i.MX7D platform.

Signed-off-by: Fugang Duan <B38611@freescale.com>
---
 arch/arm/mach-imx/mach-imx7d.c | 74 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 74 insertions(+)

diff --git a/arch/arm/mach-imx/mach-imx7d.c b/arch/arm/mach-imx/mach-imx7d.c
index 4d4a190..c06956f 100644
--- a/arch/arm/mach-imx/mach-imx7d.c
+++ b/arch/arm/mach-imx/mach-imx7d.c
@@ -6,12 +6,85 @@
  * published by the Free Software Foundation.
  */
 #include <linux/irqchip.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/imx7-iomuxc-gpr.h>
 #include <linux/of_platform.h>
+#include <linux/phy.h>
+#include <linux/regmap.h>
+
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
 #include "common.h"
 
+static int ar8031_phy_fixup(struct phy_device *dev)
+{
+	u16 val;
+
+	/* Set RGMII IO voltage to 1.8V */
+	phy_write(dev, 0x1d, 0x1f);
+	phy_write(dev, 0x1e, 0x8);
+
+	/* disable phy AR8031 SmartEEE function. */
+	phy_write(dev, 0xd, 0x3);
+	phy_write(dev, 0xe, 0x805d);
+	phy_write(dev, 0xd, 0x4003);
+	val = phy_read(dev, 0xe);
+	val &= ~(0x1 << 8);
+	phy_write(dev, 0xe, val);
+
+	/* introduce tx clock delay */
+	phy_write(dev, 0x1d, 0x5);
+	val = phy_read(dev, 0x1e);
+	val |= 0x0100;
+	phy_write(dev, 0x1e, val);
+
+	return 0;
+}
+
+static int bcm54220_phy_fixup(struct phy_device *dev)
+{
+	/* enable RXC skew select RGMII copper mode */
+	phy_write(dev, 0x1e, 0x21);
+	phy_write(dev, 0x1f, 0x7ea8);
+	phy_write(dev, 0x1e, 0x2f);
+	phy_write(dev, 0x1f, 0x71b7);
+
+	return 0;
+}
+
+#define PHY_ID_AR8031	0x004dd074
+#define PHY_ID_BCM54220	0x600d8589
+
+static void __init imx7d_enet_phy_init(void)
+{
+	if (IS_BUILTIN(CONFIG_PHYLIB)) {
+		phy_register_fixup_for_uid(PHY_ID_AR8031, 0xffffffff,
+					   ar8031_phy_fixup);
+		phy_register_fixup_for_uid(PHY_ID_BCM54220, 0xffffffff,
+					   bcm54220_phy_fixup);
+	}
+}
+
+static void __init imx7d_enet_clk_sel(void)
+{
+	struct regmap *gpr;
+
+	gpr = syscon_regmap_lookup_by_compatible("fsl,imx7d-iomuxc-gpr");
+	if (!IS_ERR(gpr)) {
+		regmap_update_bits(gpr, IOMUXC_GPR1, IMX7D_GPR1_ENET_TX_CLK_SEL_MASK, 0);
+		regmap_update_bits(gpr, IOMUXC_GPR1, IMX7D_GPR1_ENET_CLK_DIR_MASK, 0);
+	} else {
+		pr_err("failed to find fsl,imx7d-iomux-gpr regmap\n");
+	}
+}
+
+static inline void imx7d_enet_init(void)
+{
+	imx7d_enet_phy_init();
+	imx7d_enet_clk_sel();
+}
+
 static void __init imx7d_init_machine(void)
 {
 	struct device *parent;
@@ -22,6 +95,7 @@ static void __init imx7d_init_machine(void)
 
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 	imx_anatop_init();
+	imx7d_enet_init();
 }
 
 static void __init imx7d_init_irq(void)
-- 
1.9.1

[PATCH v3 3/4] ARM: dts: imx7d: add fec1 and fec2 support for i.MX7d soc

[Fugang Duan]

Add fec1 and fec2 nodes for i.MX7d soc.

Signed-off-by: Fugang Duan <B38611@freescale.com>
---
 arch/arm/boot/dts/imx7d.dtsi | 36 ++++++++++++++++++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi
index b738ce0..7631492 100644
--- a/arch/arm/boot/dts/imx7d.dtsi
+++ b/arch/arm/boot/dts/imx7d.dtsi
@@ -729,6 +729,42 @@
 				bus-width = <4>;
 				status = "disabled";
 			};
+
+			fec1: ethernet at 30be0000 {
+				compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec";
+				reg = <0x30be0000 0x10000>;
+				interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+					<&clks IMX7D_ENET_AXI_ROOT_CLK>,
+					<&clks IMX7D_ENET1_TIME_ROOT_CLK>,
+					<&clks IMX7D_PLL_ENET_MAIN_125M_CLK>,
+					<&clks IMX7D_ENET_PHY_REF_ROOT_CLK>;
+				clock-names = "ipg", "ahb", "ptp",
+					"enet_clk_ref", "enet_out";
+				fsl,num-tx-queues=<3>;
+				fsl,num-rx-queues=<3>;
+				status = "disabled";
+			};
+
+			fec2: ethernet at 30bf0000 {
+				compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec";
+				reg = <0x30bf0000 0x10000>;
+				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+					<&clks IMX7D_ENET_AXI_ROOT_CLK>,
+					<&clks IMX7D_ENET2_TIME_ROOT_CLK>,
+					<&clks IMX7D_PLL_ENET_MAIN_125M_CLK>,
+					<&clks IMX7D_ENET_PHY_REF_ROOT_CLK>;
+				clock-names = "ipg", "ahb", "ptp",
+					"enet_clk_ref", "enet_out";
+				fsl,num-tx-queues=<3>;
+				fsl,num-rx-queues=<3>;
+				status = "disabled";
+			};
 		};
 	};
 };
-- 
1.9.1

[PATCH v3 4/4] ARM: dts: imx7d-sdb: add fec1 and fec2 support

[Fugang Duan]

Enable fec1 and fec2 for i.MX7d-sdb board.

Signed-off-by: Fugang Duan <B38611@freescale.com>
---
 arch/arm/boot/dts/imx7d-sdb.dts | 76 ++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 75 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index 4d1a4b9..7d3e980 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -101,6 +101,45 @@
 	arm-supply = <&sw1a_reg>;
 };
 
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy at 0 {
+			reg = <0>;
+		};
+
+		ethphy1: ethernet-phy at 1 {
+			reg = <1>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	assigned-clocks = <&clks IMX7D_ENET2_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET2_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	status = "okay";
+};
+
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
@@ -246,6 +285,42 @@
 	pinctrl-0 = <&pinctrl_hog>;
 
 	imx7d-sdb {
+		pinctrl_enet1: enet1grp {
+			fsl,pins = <
+				MX7D_PAD_GPIO1_IO10__ENET1_MDIO			0x3
+				MX7D_PAD_GPIO1_IO11__ENET1_MDC			0x3
+				MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC	0x1
+				MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x1
+				MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x1
+				MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2	0x1
+				MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3	0x1
+				MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x1
+				MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC	0x1
+				MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x1
+				MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x1
+				MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x1
+				MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x1
+				MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x1
+			>;
+		};
+
+		pinctrl_enet2: enet2grp {
+			fsl,pins = <
+				MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC		0x1
+				MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0		0x1
+				MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1		0x1
+				MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2		0x1
+				MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3		0x1
+				MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL		0x1
+				MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC		0x1
+				MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0		0x1
+				MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1		0x1
+				MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2		0x1
+				MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3		0x1
+				MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL		0x1
+			>;
+		};
+
 		pinctrl_hog: hoggrp {
 			fsl,pins = <
 				MX7D_PAD_UART3_CTS_B__GPIO4_IO7		0x14
@@ -281,7 +356,6 @@
 			>;
 		};
 
-
 		pinctrl_uart1: uart1grp {
 			fsl,pins = <
 				MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX	0x79
-- 
1.9.1

[PATCH v3 0/4] Add fec1 and fec2 support for i.MX7d sdb board

[Shawn Guo]

On Mon, Sep 07, 2015 at 10:54:58AM +0800, Fugang Duan wrote:
> Fugang Duan (4):
>   ARM: imx7d: add imx7d iomux-gpr field define
>   ARM: imx: add enet init for i.MX7D platform
>   ARM: dts: imx7d: add fec1 and fec2 support for i.MX7d soc

Applied above 3.

>   ARM: dts: imx7d-sdb: add fec1 and fec2 support

Will apply this one after the prerequisite is applied.

Shawn

[PATCH v3 4/4] ARM: dts: imx7d-sdb: add fec1 and fec2 support

[Shawn Guo]

On Mon, Sep 07, 2015 at 10:55:02AM +0800, Fugang Duan wrote:
> Enable fec1 and fec2 for i.MX7d-sdb board.
> 
> Signed-off-by: Fugang Duan <B38611@freescale.com>

Applied, thanks.