* [PATCH V2 1/2] devicetree: bindings: Add vendor prefix for Kosagi @ 2015-11-28 14:47 Marek Vasut 2015-11-28 14:47 ` [PATCH V3 2/2] ARM: dts: imx6q: add Novena board Marek Vasut 2015-12-14 1:36 ` [PATCH V2 1/2] devicetree: bindings: Add vendor prefix for Kosagi Shawn Guo 0 siblings, 2 replies; 22+ messages in thread From: Marek Vasut @ 2015-11-28 14:47 UTC (permalink / raw) To: linux-arm-kernel From: Sean Cross <xobs@kosagi.com> Add a vendor prefix for Sutajio Ko-Usagi PTE Ltd., which goes by the more common name of Kosagi. Signed-off-by: Sean Cross <xobs@kosagi.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Rob Herring <robh@kernel.org> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <fabio.estevam@freescale.com> --- Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+) V2: Add my SoB line. diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 62ff22f..d3ee06e 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -124,6 +124,7 @@ jedec JEDEC Solid State Technology Association karo Ka-Ro electronics GmbH keymile Keymile GmbH kinetic Kinetic Technologies +kosagi Sutajio Ko-Usagi PTE Ltd. lacie LaCie lantiq Lantiq Semiconductor lenovo Lenovo Group Ltd. -- 2.1.4 ^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH V3 2/2] ARM: dts: imx6q: add Novena board 2015-11-28 14:47 [PATCH V2 1/2] devicetree: bindings: Add vendor prefix for Kosagi Marek Vasut @ 2015-11-28 14:47 ` Marek Vasut 2015-11-30 10:19 ` Lucas Stach ` (2 more replies) 2015-12-14 1:36 ` [PATCH V2 1/2] devicetree: bindings: Add vendor prefix for Kosagi Shawn Guo 1 sibling, 3 replies; 22+ messages in thread From: Marek Vasut @ 2015-11-28 14:47 UTC (permalink / raw) To: linux-arm-kernel From: Sean Cross <xobs@kosagi.com> Novena is an open-hardware laptop/desktop/bare board. See http://www.kosagi.com/w/index.php?title=Novena_Main_Page Signed-off-by: Sean Cross <xobs@kosagi.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Sean Cross <xobs@kosagi.com> Cc: Shawn Guo <shawnguo@kernel.org> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6q-novena.dts | 846 +++++++++++++++++++++++++++++++++++++ 2 files changed, 847 insertions(+) create mode 100644 arch/arm/boot/dts/imx6q-novena.dts V2: Fix the PCIe regulator, make it always on Fix the polarity of SD2 WP and CD lines, make them active low. Drop the simple-bus for regulators, put them in /soc instead. Configure the mux of all pins instead of depending on bootloader. Change license to Dual X11/GPLv2+ (Acked by Sean) Sort the nodes alphabetically. V3: Drop the spidev node Drop the fsl,mode = "i2s-slave"; Move regulators into / diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 760a737..9eb8fa8 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -325,6 +325,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-hummingboard.dtb \ imx6q-nitrogen6x.dtb \ imx6q-nitrogen6_max.dtb \ + imx6q-novena.dtb \ imx6q-phytec-pbab01.dtb \ imx6q-rex-pro.dtb \ imx6q-sabreauto.dtb \ diff --git a/arch/arm/boot/dts/imx6q-novena.dts b/arch/arm/boot/dts/imx6q-novena.dts new file mode 100644 index 0000000..a6b179e --- /dev/null +++ b/arch/arm/boot/dts/imx6q-novena.dts @@ -0,0 +1,846 @@ +/* + * Copyright 2015 Sutajio Ko-Usagi PTE LTD + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this file; if not, write to the Free + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "Kosagi Novena Dual/Quad"; + compatible = "kosagi,imx6q-novena", "fsl,imx6q"; + + memory { + reg = <0x10000000 0xefffffff>; + }; + + chosen { + stdout-path = &uart2; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 10000000>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_backlight_novena>; + power-supply = <®_lvds_lcd>; + + brightness-levels = <0 3 6 12 16 24 32 48 64 96 128 192 255>; + default-brightness-level = <12>; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys_novena>; + + user-button { + label = "User Button"; + gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + }; + + lid { + label = "Lid"; + gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; + linux,input-type = <5>; /* EV_SW */ + linux,code = <0>; /* SW_LID */ + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds_novena>; + + heartbeat { + label = "novena:white:panel"; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + }; + + panel: panel { + compatible = "innolux,n133hse-ea1", "simple-panel"; + backlight = <&backlight>; + }; + + reg_2p5v: 2p5v { + compatible = "regulator-fixed"; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_3p3v: 3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_audio_codec: es8328-regulator { + compatible = "regulator-fixed"; + regulator-name = "es8328-power"; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + startup-delay-us = <400000>; + gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_display: display-regulator { + compatible = "regulator-fixed"; + regulator-name = "lcd-display-power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <200000>; + gpio = <&gpio5 28 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_lvds_lcd: lcd-regulator { + compatible = "regulator-fixed"; + regulator-name = "lcd-lvds-power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_pcie: pcie-regulator { + compatible = "regulator-fixed"; + regulator-name = "pcie-bus-power"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + reg_sata: sata-regulator { + compatible = "regulator-fixed"; + regulator-name = "sata-power"; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <10000>; + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_otg_vbus: usb_otg_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + }; + + sound { + compatible = "fsl,imx-audio-es8328"; + model = "imx-audio-es8328"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-amp-supply = <®_audio_codec>; + jack-gpio = <&gpio5 15 GPIO_ACTIVE_HIGH>; + audio-routing = + "Speaker", "LOUT2", + "Speaker", "ROUT2", + "Speaker", "audio-amp", + "Headphone", "ROUT1", + "Headphone", "LOUT1", + "LINPUT1", "Mic Jack", + "RINPUT1", "Mic Jack", + "Mic Jack", "Mic Bias"; + mux-int-port = <0x1>; + mux-ext-port = <0x3>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux_novena>; + status = "okay"; +}; + +&ecspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3_novena>; + fsl,spi-num-chipselects = <3>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_novena>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + rxc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + txc-skew-ps = <3000>; + txen-skew-ps = <0>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txd0-skew-ps = <3000>; + txd1-skew-ps = <3000>; + txd2-skew-ps = <3000>; + txd3-skew-ps = <3000>; + status = "okay"; +}; + +&hdmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hdmi_novena>; + ddc-i2c-bus = <&i2c2>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_novena>; + status = "okay"; + + accel: mma8452 at 1c { + compatible = "fsl,mma8452"; + reg = <0x1c>; + }; + + rtc: pcf8523 at 68 { + compatible = "nxp,pcf8523"; + reg = <0x68>; + }; + + sbs_battery: bq20z75 at 0b { + compatible = "sbs,sbs-battery"; + reg = <0x0b>; + sbs,i2c-retry-count = <50>; + }; + + touch: stmpe811 at 44 { + compatible = "st,stmpe811"; + reg = <0x44>; + #address-cells = <1>; + #size-cells = <0>; + irq-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; + id = <0>; + blocks = <0x5>; + irq-trigger = <0x1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_stmpe_novena>; + vio-supply = <®_3p3v>; + vcc-supply = <®_3p3v>; + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + st,sample-time = <4>; + st,mod-12b = <1>; + st,ref-sel = <0>; + st,adc-freq = <1>; + st,ave-ctrl = <1>; + st,touch-det-delay = <2>; + st,settling = <2>; + st,fraction-z = <7>; + st,i-drive = <1>; + }; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2_novena>; + status = "okay"; + + pmic: pfuze100 at 08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + regulator-boot-on; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3_novena>; + status = "okay"; + + codec: es8328 at 11 { + compatible = "everest,es8328"; + reg = <0x11>; + DVDD-supply = <®_audio_codec>; + AVDD-supply = <®_audio_codec>; + PVDD-supply = <®_audio_codec>; + HPVDD-supply = <®_audio_codec>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sound_novena>; + + clocks = <&clks IMX6QDL_CLK_CKO1>; + assigned-clocks = <&clks IMX6QDL_CLK_CKO>, <&clks IMX6QDL_CLK_CKO1_SEL>, <&clks IMX6QDL_CLK_PLL4_AUDIO>, <&clks IMX6QDL_CLK_CKO1>; + assigned-clock-parents = <&clks IMX6QDL_CLK_CKO1>, <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>, <&clks IMX6QDL_CLK_OSC>, <&clks IMX6QDL_CLK_CKO1_PODF>; + assigned-clock-rates = <0 0 722534400 22579200>; + }; +}; + +&iomuxc { + audmux { + pinctrl_audmux_novena: audmuxgrp-novena { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + }; + + backlight { + pinctrl_backlight_novena: backlightgrp-novena { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0 + MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x1b0b1 + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b1 + >; + }; + }; + + ecspi3 { + pinctrl_ecspi3_novena: ecspi3grp-novena { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1 + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1 + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1 + >; + }; + }; + + enet { + pinctrl_enet_novena: enetgrp-novena { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b020 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b028 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b028 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b028 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b028 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b028 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + + /* Ethernet reset */ + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b1 + >; + }; + }; + + fpga { + pinctrl_fpga_gpio: fpgagpiogrp-novena { + fsl,pins = < + /* FPGA power */ + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b1 + + /* Reset */ + MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b1 + + /* FPGA GPIOs */ + MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x1b0b1 + MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x1b0b1 + MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x1b0b1 + MX6QDL_PAD_EIM_DA3__GPIO3_IO03 0x1b0b1 + MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x1b0b1 + MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x1b0b1 + MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x1b0b1 + MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x1b0b1 + MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x1b0b1 + MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x1b0b1 + MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x1b0b1 + MX6QDL_PAD_EIM_DA11__GPIO3_IO11 0x1b0b1 + MX6QDL_PAD_EIM_DA12__GPIO3_IO12 0x1b0b1 + MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x1b0b1 + MX6QDL_PAD_EIM_DA14__GPIO3_IO14 0x1b0b1 + MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x1b0b1 + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b0b1 + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b1 + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 + MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b1 + MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b1 + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b1 + MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x1b0b1 + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x1b0b1 + MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x1b0b1 + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b1 + >; + }; + + pinctrl_fpga_eim: fpgaeimgrp-novena { + fsl,pins = < + /* FPGA power */ + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b1 + + /* Reset */ + MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b1 + + /* FPGA GPIOs */ + MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0f1 + MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0f1 + MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0f1 + MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0f1 + MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0f1 + MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0f1 + MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0f1 + MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0f1 + MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0f1 + MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0f1 + MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0f1 + MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0f1 + MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0f1 + MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0f1 + MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0f1 + MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0f1 + MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0f1 + MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0f1 + MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0f1 + MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0f1 + MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0f1 + MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0f1 + MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0f1 + MX6QDL_PAD_EIM_RW__EIM_RW 0xb0f1 + MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb0f1 + MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0f1 + >; + }; + }; + + gpio_keys { + pinctrl_gpio_keys_novena: gpiokeysgrp-novena { + fsl,pins = < + /* User button */ + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b0b0 + + /* PCIe Wakeup */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1f0e0 + + /* Lid switch */ + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0 + >; + }; + }; + + hdmi { + pinctrl_hdmi_novena: hdmigrp-novena { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0 + MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x1b0b1 + >; + }; + }; + + i2c1 { + pinctrl_i2c1_novena: i2c1grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + }; + + i2c2 { + pinctrl_i2c2_novena: i2c2grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1 + >; + }; + }; + + i2c3 { + pinctrl_i2c3_novena: i2c3grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 + >; + }; + }; + + kpp-keys { + pinctrl_kpp_novena: kppgrp-novena { + fsl,pins = < + /* Front panel button */ + MX6QDL_PAD_KEY_ROW1__KEY_ROW1 0x1b0b1 + + /* Fake column driver, not connected */ + MX6QDL_PAD_KEY_COL1__KEY_COL1 0x1b0b1 + >; + }; + }; + + leds { + pinctrl_leds_novena: ledsgrp-novena { + fsl,pins = < + MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x1b0b1 + >; + }; + }; + + pcie { + pinctrl_pcie_novena: pciegrp-novena { + fsl,pins = < + /* Reset */ + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b1 + + /* Power On */ + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b1 + + /* Wifi kill */ + MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x1b0b1 + >; + }; + }; + + sata { + pinctrl_sata_novena: satagrp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x1b0b1 + >; + }; + }; + + senoko { + pinctrl_senoko_novena: senokogrp-novena { + fsl,pins = < + /* Senoko IRQ line */ + MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x13048 + + /* Senoko reset line */ + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1b0b1 + >; + }; + }; + + sound { + pinctrl_sound_novena: soundgrp-novena { + fsl,pins = < + /* Audio power regulator */ + MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x1b0b1 + + /* Headphone plug */ + MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x1b0b1 + + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000b0 + >; + }; + }; + + ts { + pinctrl_stmpe_novena: stmpegrp-novena { + fsl,pins = < + /* Touchscreen interrupt */ + MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1b0b1 + >; + }; + }; + + uart2 { + pinctrl_uart2_novena: uart2grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + }; + + uart3 { + pinctrl_uart3_novena: uart3grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + >; + }; + }; + uart4 { + pinctrl_uart4_novena: uart4grp-novena { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1 + >; + }; + }; + + usbotg { + pinctrl_usbotg_novena: usbotggrp-novena { + fsl,pins = < + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 + >; + }; + }; + + usdhc2 { + pinctrl_usdhc2_novena: usdhc2grp-novena { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170f9 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100f9 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170f9 + + /* Write protect */ + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b1 + + /* Card detect */ + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b1 + >; + }; + }; + + usdhc3 { + pinctrl_usdhc3_novena: usdhc3grp-novena { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9 + >; + }; + }; +}; + +&kpp { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp_novena>; + linux,keymap = < + MATRIX_KEY(1, 1, KEY_CONFIG) + >; + status = "okay"; +}; + +&ldb { + fsl,dual-channel; + status = "okay"; + lvds-channel at 0 { + fsl,data-mapping = "jeida"; + fsl,data-width = <24>; + fsl,panel = <&panel>; + status = "okay"; + }; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie_novena>; + reset-gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&sata { + target-supply = <®_sata>; + fsl,transmit-level-mV = <1025>; + fsl,transmit-boost-mdB = <0>; + fsl,transmit-atten-16ths = <8>; + status = "okay"; +}; + +&ssi1 { + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2_novena>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3_novena>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4_novena>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + dr_mode = "otg"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg_novena>; + disable-over-current; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <&swbst_reg>; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2_novena>; + cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; + bus-width = <4>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3_novena>; + bus-width = <4>; + non-removable; + status = "okay"; +}; -- 2.1.4 ^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH V3 2/2] ARM: dts: imx6q: add Novena board 2015-11-28 14:47 ` [PATCH V3 2/2] ARM: dts: imx6q: add Novena board Marek Vasut @ 2015-11-30 10:19 ` Lucas Stach 2015-11-30 12:21 ` Marek Vasut 2015-11-30 10:57 ` Fabio Estevam 2015-12-02 7:53 ` Shawn Guo 2 siblings, 1 reply; 22+ messages in thread From: Lucas Stach @ 2015-11-30 10:19 UTC (permalink / raw) To: linux-arm-kernel Am Samstag, den 28.11.2015, 15:47 +0100 schrieb Marek Vasut: > From: Sean Cross <xobs@kosagi.com> > > Novena is an open-hardware laptop/desktop/bare board. > > See http://www.kosagi.com/w/index.php?title=Novena_Main_Page > > Signed-off-by: Sean Cross <xobs@kosagi.com> > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Fabio Estevam <fabio.estevam@freescale.com> > Cc: Lucas Stach <l.stach@pengutronix.de> > Cc: Sean Cross <xobs@kosagi.com> > Cc: Shawn Guo <shawnguo@kernel.org> Looks really good to me now: Reviewed-by: Lucas Stach <l.stach@pengutronix.de> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx6q-novena.dts | 846 +++++++++++++++++++++++++++++++++++++ > 2 files changed, 847 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6q-novena.dts > > V2: Fix the PCIe regulator, make it always on > Fix the polarity of SD2 WP and CD lines, make them active low. > Drop the simple-bus for regulators, put them in /soc instead. > Configure the mux of all pins instead of depending on bootloader. > Change license to Dual X11/GPLv2+ (Acked by Sean) > Sort the nodes alphabetically. > > V3: Drop the spidev node > Drop the fsl,mode = "i2s-slave"; > Move regulators into / > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 760a737..9eb8fa8 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -325,6 +325,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > imx6q-hummingboard.dtb \ > imx6q-nitrogen6x.dtb \ > imx6q-nitrogen6_max.dtb \ > + imx6q-novena.dtb \ > imx6q-phytec-pbab01.dtb \ > imx6q-rex-pro.dtb \ > imx6q-sabreauto.dtb \ > diff --git a/arch/arm/boot/dts/imx6q-novena.dts b/arch/arm/boot/dts/imx6q-novena.dts > new file mode 100644 > index 0000000..a6b179e > --- /dev/null > +++ b/arch/arm/boot/dts/imx6q-novena.dts > @@ -0,0 +1,846 @@ > +/* > + * Copyright 2015 Sutajio Ko-Usagi PTE LTD > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of > + * the License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * You should have received a copy of the GNU General Public > + * License along with this file; if not, write to the Free > + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, > + * MA 02110-1301 USA > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + * > + */ > + > +/dts-v1/; > +#include "imx6q.dtsi" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +/ { > + model = "Kosagi Novena Dual/Quad"; > + compatible = "kosagi,imx6q-novena", "fsl,imx6q"; > + > + memory { > + reg = <0x10000000 0xefffffff>; > + }; > + > + chosen { > + stdout-path = &uart2; > + }; > + > + backlight: backlight { > + compatible = "pwm-backlight"; > + pwms = <&pwm1 0 10000000>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_backlight_novena>; > + power-supply = <®_lvds_lcd>; > + > + brightness-levels = <0 3 6 12 16 24 32 48 64 96 128 192 255>; > + default-brightness-level = <12>; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gpio_keys_novena>; > + > + user-button { > + label = "User Button"; > + gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_POWER>; > + }; > + > + lid { > + label = "Lid"; > + gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; > + linux,input-type = <5>; /* EV_SW */ > + linux,code = <0>; /* SW_LID */ > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_leds_novena>; > + > + heartbeat { > + label = "novena:white:panel"; > + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "default-on"; > + }; > + }; > + > + panel: panel { > + compatible = "innolux,n133hse-ea1", "simple-panel"; > + backlight = <&backlight>; > + }; > + > + reg_2p5v: 2p5v { > + compatible = "regulator-fixed"; > + regulator-name = "2P5V"; > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <2500000>; > + regulator-always-on; > + }; > + > + reg_3p3v: 3p3v { > + compatible = "regulator-fixed"; > + regulator-name = "3P3V"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + reg_audio_codec: es8328-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "es8328-power"; > + regulator-boot-on; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + startup-delay-us = <400000>; > + gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_display: display-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "lcd-display-power"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + startup-delay-us = <200000>; > + gpio = <&gpio5 28 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_lvds_lcd: lcd-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "lcd-lvds-power"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_pcie: pcie-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "pcie-bus-power"; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <1500000>; > + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-always-on; > + }; > + > + reg_sata: sata-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "sata-power"; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + startup-delay-us = <10000>; > + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_usb_otg_vbus: usb_otg_vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb_otg_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + }; > + > + sound { > + compatible = "fsl,imx-audio-es8328"; > + model = "imx-audio-es8328"; > + ssi-controller = <&ssi1>; > + audio-codec = <&codec>; > + audio-amp-supply = <®_audio_codec>; > + jack-gpio = <&gpio5 15 GPIO_ACTIVE_HIGH>; > + audio-routing = > + "Speaker", "LOUT2", > + "Speaker", "ROUT2", > + "Speaker", "audio-amp", > + "Headphone", "ROUT1", > + "Headphone", "LOUT1", > + "LINPUT1", "Mic Jack", > + "RINPUT1", "Mic Jack", > + "Mic Jack", "Mic Bias"; > + mux-int-port = <0x1>; > + mux-ext-port = <0x3>; > + }; > +}; > + > +&audmux { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_audmux_novena>; > + status = "okay"; > +}; > + > +&ecspi3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ecspi3_novena>; > + fsl,spi-num-chipselects = <3>; > + status = "okay"; > +}; > + > +&fec { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_enet_novena>; > + phy-mode = "rgmii"; > + phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; > + rxc-skew-ps = <3000>; > + rxdv-skew-ps = <0>; > + txc-skew-ps = <3000>; > + txen-skew-ps = <0>; > + rxd0-skew-ps = <0>; > + rxd1-skew-ps = <0>; > + rxd2-skew-ps = <0>; > + rxd3-skew-ps = <0>; > + txd0-skew-ps = <3000>; > + txd1-skew-ps = <3000>; > + txd2-skew-ps = <3000>; > + txd3-skew-ps = <3000>; > + status = "okay"; > +}; > + > +&hdmi { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hdmi_novena>; > + ddc-i2c-bus = <&i2c2>; > + status = "okay"; > +}; > + > +&i2c1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1_novena>; > + status = "okay"; > + > + accel: mma8452 at 1c { > + compatible = "fsl,mma8452"; > + reg = <0x1c>; > + }; > + > + rtc: pcf8523 at 68 { > + compatible = "nxp,pcf8523"; > + reg = <0x68>; > + }; > + > + sbs_battery: bq20z75 at 0b { > + compatible = "sbs,sbs-battery"; > + reg = <0x0b>; > + sbs,i2c-retry-count = <50>; > + }; > + > + touch: stmpe811 at 44 { > + compatible = "st,stmpe811"; > + reg = <0x44>; > + #address-cells = <1>; > + #size-cells = <0>; > + irq-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; > + id = <0>; > + blocks = <0x5>; > + irq-trigger = <0x1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_stmpe_novena>; > + vio-supply = <®_3p3v>; > + vcc-supply = <®_3p3v>; > + > + stmpe_touchscreen { > + compatible = "st,stmpe-ts"; > + st,sample-time = <4>; > + st,mod-12b = <1>; > + st,ref-sel = <0>; > + st,adc-freq = <1>; > + st,ave-ctrl = <1>; > + st,touch-det-delay = <2>; > + st,settling = <2>; > + st,fraction-z = <7>; > + st,i-drive = <1>; > + }; > + }; > +}; > + > +&i2c2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2_novena>; > + status = "okay"; > + > + pmic: pfuze100 at 08 { > + compatible = "fsl,pfuze100"; > + reg = <0x08>; > + > + regulators { > + sw1a_reg: sw1ab { > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <1875000>; > + regulator-boot-on; > + regulator-always-on; > + regulator-ramp-delay = <6250>; > + }; > + > + sw1c_reg: sw1c { > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <1875000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw2_reg: sw2 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw3a_reg: sw3a { > + regulator-min-microvolt = <400000>; > + regulator-max-microvolt = <1975000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw3b_reg: sw3b { > + regulator-min-microvolt = <400000>; > + regulator-max-microvolt = <1975000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw4_reg: sw4 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + swbst_reg: swbst { > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5150000>; > + regulator-boot-on; > + }; > + > + snvs_reg: vsnvs { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <3000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vref_reg: vrefddr { > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vgen1_reg: vgen1 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1550000>; > + }; > + > + vgen2_reg: vgen2 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1550000>; > + }; > + > + vgen3_reg: vgen3 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + vgen4_reg: vgen4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vgen5_reg: vgen5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vgen6_reg: vgen6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + }; > + }; > +}; > + > +&i2c3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3_novena>; > + status = "okay"; > + > + codec: es8328 at 11 { > + compatible = "everest,es8328"; > + reg = <0x11>; > + DVDD-supply = <®_audio_codec>; > + AVDD-supply = <®_audio_codec>; > + PVDD-supply = <®_audio_codec>; > + HPVDD-supply = <®_audio_codec>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sound_novena>; > + > + clocks = <&clks IMX6QDL_CLK_CKO1>; > + assigned-clocks = <&clks IMX6QDL_CLK_CKO>, <&clks IMX6QDL_CLK_CKO1_SEL>, <&clks IMX6QDL_CLK_PLL4_AUDIO>, <&clks IMX6QDL_CLK_CKO1>; > + assigned-clock-parents = <&clks IMX6QDL_CLK_CKO1>, <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>, <&clks IMX6QDL_CLK_OSC>, <&clks IMX6QDL_CLK_CKO1_PODF>; > + assigned-clock-rates = <0 0 722534400 22579200>; > + }; > +}; > + > +&iomuxc { > + audmux { > + pinctrl_audmux_novena: audmuxgrp-novena { > + fsl,pins = < > + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 > + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 > + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 > + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 > + >; > + }; > + }; > + > + backlight { > + pinctrl_backlight_novena: backlightgrp-novena { > + fsl,pins = < > + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0 > + MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x1b0b1 > + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b1 > + >; > + }; > + }; > + > + ecspi3 { > + pinctrl_ecspi3_novena: ecspi3grp-novena { > + fsl,pins = < > + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1 > + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1 > + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1 > + >; > + }; > + }; > + > + enet { > + pinctrl_enet_novena: enetgrp-novena { > + fsl,pins = < > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 > + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b020 > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b028 > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b028 > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b028 > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b028 > + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b028 > + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 > + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 > + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 > + > + /* Ethernet reset */ > + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b1 > + >; > + }; > + }; > + > + fpga { > + pinctrl_fpga_gpio: fpgagpiogrp-novena { > + fsl,pins = < > + /* FPGA power */ > + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b1 > + > + /* Reset */ > + MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b1 > + > + /* FPGA GPIOs */ > + MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x1b0b1 > + MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x1b0b1 > + MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x1b0b1 > + MX6QDL_PAD_EIM_DA3__GPIO3_IO03 0x1b0b1 > + MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x1b0b1 > + MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x1b0b1 > + MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x1b0b1 > + MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x1b0b1 > + MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x1b0b1 > + MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x1b0b1 > + MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x1b0b1 > + MX6QDL_PAD_EIM_DA11__GPIO3_IO11 0x1b0b1 > + MX6QDL_PAD_EIM_DA12__GPIO3_IO12 0x1b0b1 > + MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x1b0b1 > + MX6QDL_PAD_EIM_DA14__GPIO3_IO14 0x1b0b1 > + MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x1b0b1 > + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b0b1 > + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b1 > + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 > + MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b1 > + MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b1 > + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b1 > + MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x1b0b1 > + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x1b0b1 > + MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x1b0b1 > + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b1 > + >; > + }; > + > + pinctrl_fpga_eim: fpgaeimgrp-novena { > + fsl,pins = < > + /* FPGA power */ > + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b1 > + > + /* Reset */ > + MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b1 > + > + /* FPGA GPIOs */ > + MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0f1 > + MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0f1 > + MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0f1 > + MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0f1 > + MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0f1 > + MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0f1 > + MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0f1 > + MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0f1 > + MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0f1 > + MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0f1 > + MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0f1 > + MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0f1 > + MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0f1 > + MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0f1 > + MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0f1 > + MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0f1 > + MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0f1 > + MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0f1 > + MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0f1 > + MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0f1 > + MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0f1 > + MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0f1 > + MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0f1 > + MX6QDL_PAD_EIM_RW__EIM_RW 0xb0f1 > + MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb0f1 > + MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0f1 > + >; > + }; > + }; > + > + gpio_keys { > + pinctrl_gpio_keys_novena: gpiokeysgrp-novena { > + fsl,pins = < > + /* User button */ > + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b0b0 > + > + /* PCIe Wakeup */ > + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1f0e0 > + > + /* Lid switch */ > + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0 > + >; > + }; > + }; > + > + hdmi { > + pinctrl_hdmi_novena: hdmigrp-novena { > + fsl,pins = < > + MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0 > + MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x1b0b1 > + >; > + }; > + }; > + > + i2c1 { > + pinctrl_i2c1_novena: i2c1grp-novena { > + fsl,pins = < > + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 > + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 > + >; > + }; > + }; > + > + i2c2 { > + pinctrl_i2c2_novena: i2c2grp-novena { > + fsl,pins = < > + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1 > + MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1 > + >; > + }; > + }; > + > + i2c3 { > + pinctrl_i2c3_novena: i2c3grp-novena { > + fsl,pins = < > + MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1 > + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 > + >; > + }; > + }; > + > + kpp-keys { > + pinctrl_kpp_novena: kppgrp-novena { > + fsl,pins = < > + /* Front panel button */ > + MX6QDL_PAD_KEY_ROW1__KEY_ROW1 0x1b0b1 > + > + /* Fake column driver, not connected */ > + MX6QDL_PAD_KEY_COL1__KEY_COL1 0x1b0b1 > + >; > + }; > + }; > + > + leds { > + pinctrl_leds_novena: ledsgrp-novena { > + fsl,pins = < > + MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x1b0b1 > + >; > + }; > + }; > + > + pcie { > + pinctrl_pcie_novena: pciegrp-novena { > + fsl,pins = < > + /* Reset */ > + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b1 > + > + /* Power On */ > + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b1 > + > + /* Wifi kill */ > + MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x1b0b1 > + >; > + }; > + }; > + > + sata { > + pinctrl_sata_novena: satagrp-novena { > + fsl,pins = < > + MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x1b0b1 > + >; > + }; > + }; > + > + senoko { > + pinctrl_senoko_novena: senokogrp-novena { > + fsl,pins = < > + /* Senoko IRQ line */ > + MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x13048 > + > + /* Senoko reset line */ > + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1b0b1 > + >; > + }; > + }; > + > + sound { > + pinctrl_sound_novena: soundgrp-novena { > + fsl,pins = < > + /* Audio power regulator */ > + MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x1b0b1 > + > + /* Headphone plug */ > + MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x1b0b1 > + > + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000b0 > + >; > + }; > + }; > + > + ts { > + pinctrl_stmpe_novena: stmpegrp-novena { > + fsl,pins = < > + /* Touchscreen interrupt */ > + MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1b0b1 > + >; > + }; > + }; > + > + uart2 { > + pinctrl_uart2_novena: uart2grp-novena { > + fsl,pins = < > + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 > + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 > + >; > + }; > + }; > + > + uart3 { > + pinctrl_uart3_novena: uart3grp-novena { > + fsl,pins = < > + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 > + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 > + >; > + }; > + }; > + uart4 { > + pinctrl_uart4_novena: uart4grp-novena { > + fsl,pins = < > + MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1 > + MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1 > + >; > + }; > + }; > + > + usbotg { > + pinctrl_usbotg_novena: usbotggrp-novena { > + fsl,pins = < > + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 > + >; > + }; > + }; > + > + usdhc2 { > + pinctrl_usdhc2_novena: usdhc2grp-novena { > + fsl,pins = < > + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170f9 > + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100f9 > + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9 > + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9 > + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9 > + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170f9 > + > + /* Write protect */ > + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b1 > + > + /* Card detect */ > + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b1 > + >; > + }; > + }; > + > + usdhc3 { > + pinctrl_usdhc3_novena: usdhc3grp-novena { > + fsl,pins = < > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9 > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9 > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9 > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9 > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9 > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9 > + >; > + }; > + }; > +}; > + > +&kpp { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_kpp_novena>; > + linux,keymap = < > + MATRIX_KEY(1, 1, KEY_CONFIG) > + >; > + status = "okay"; > +}; > + > +&ldb { > + fsl,dual-channel; > + status = "okay"; > + lvds-channel at 0 { > + fsl,data-mapping = "jeida"; > + fsl,data-width = <24>; > + fsl,panel = <&panel>; > + status = "okay"; > + }; > +}; > + > +&pcie { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pcie_novena>; > + reset-gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>; > + status = "okay"; > +}; > + > +&sata { > + target-supply = <®_sata>; > + fsl,transmit-level-mV = <1025>; > + fsl,transmit-boost-mdB = <0>; > + fsl,transmit-atten-16ths = <8>; > + status = "okay"; > +}; > + > +&ssi1 { > + status = "okay"; > +}; > + > +&uart2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2_novena>; > + status = "okay"; > +}; > + > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3_novena>; > + status = "okay"; > +}; > + > +&uart4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart4_novena>; > + status = "okay"; > +}; > + > +&usbotg { > + vbus-supply = <®_usb_otg_vbus>; > + dr_mode = "otg"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg_novena>; > + disable-over-current; > + status = "okay"; > +}; > + > +&usbh1 { > + vbus-supply = <&swbst_reg>; > + status = "okay"; > +}; > + > +&usdhc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc2_novena>; > + cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; > + wp-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; > + bus-width = <4>; > + status = "okay"; > +}; > + > +&usdhc3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc3_novena>; > + bus-width = <4>; > + non-removable; > + status = "okay"; > +}; -- Pengutronix e.K. | Lucas Stach | Industrial Linux Solutions | http://www.pengutronix.de/ | ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V3 2/2] ARM: dts: imx6q: add Novena board 2015-11-30 10:19 ` Lucas Stach @ 2015-11-30 12:21 ` Marek Vasut 0 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2015-11-30 12:21 UTC (permalink / raw) To: linux-arm-kernel aOn Monday, November 30, 2015 at 11:19:29 AM, Lucas Stach wrote: > Am Samstag, den 28.11.2015, 15:47 +0100 schrieb Marek Vasut: > > From: Sean Cross <xobs@kosagi.com> > > > > Novena is an open-hardware laptop/desktop/bare board. > > > > See http://www.kosagi.com/w/index.php?title=Novena_Main_Page > > > > Signed-off-by: Sean Cross <xobs@kosagi.com> > > Signed-off-by: Marek Vasut <marex@denx.de> > > Cc: Fabio Estevam <fabio.estevam@freescale.com> > > Cc: Lucas Stach <l.stach@pengutronix.de> > > Cc: Sean Cross <xobs@kosagi.com> > > Cc: Shawn Guo <shawnguo@kernel.org> > > Looks really good to me now: > Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Thanks! Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V3 2/2] ARM: dts: imx6q: add Novena board 2015-11-28 14:47 ` [PATCH V3 2/2] ARM: dts: imx6q: add Novena board Marek Vasut 2015-11-30 10:19 ` Lucas Stach @ 2015-11-30 10:57 ` Fabio Estevam 2015-12-02 7:53 ` Shawn Guo 2 siblings, 0 replies; 22+ messages in thread From: Fabio Estevam @ 2015-11-30 10:57 UTC (permalink / raw) To: linux-arm-kernel On Sat, Nov 28, 2015 at 12:47 PM, Marek Vasut <marex@denx.de> wrote: > From: Sean Cross <xobs@kosagi.com> > > Novena is an open-hardware laptop/desktop/bare board. > > See http://www.kosagi.com/w/index.php?title=Novena_Main_Page > > Signed-off-by: Sean Cross <xobs@kosagi.com> > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Fabio Estevam <fabio.estevam@freescale.com> > Cc: Lucas Stach <l.stach@pengutronix.de> > Cc: Sean Cross <xobs@kosagi.com> > Cc: Shawn Guo <shawnguo@kernel.org> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V3 2/2] ARM: dts: imx6q: add Novena board 2015-11-28 14:47 ` [PATCH V3 2/2] ARM: dts: imx6q: add Novena board Marek Vasut 2015-11-30 10:19 ` Lucas Stach 2015-11-30 10:57 ` Fabio Estevam @ 2015-12-02 7:53 ` Shawn Guo 2015-12-02 15:41 ` Marek Vasut 2 siblings, 1 reply; 22+ messages in thread From: Shawn Guo @ 2015-12-02 7:53 UTC (permalink / raw) To: linux-arm-kernel On Sat, Nov 28, 2015 at 03:47:04PM +0100, Marek Vasut wrote: > From: Sean Cross <xobs@kosagi.com> > > Novena is an open-hardware laptop/desktop/bare board. > > See http://www.kosagi.com/w/index.php?title=Novena_Main_Page > > Signed-off-by: Sean Cross <xobs@kosagi.com> > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Fabio Estevam <fabio.estevam@freescale.com> > Cc: Lucas Stach <l.stach@pengutronix.de> > Cc: Sean Cross <xobs@kosagi.com> > Cc: Shawn Guo <shawnguo@kernel.org> Looks pretty good. Some minor comments are below. Most of them are format/style nits. > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx6q-novena.dts | 846 +++++++++++++++++++++++++++++++++++++ > 2 files changed, 847 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6q-novena.dts > > V2: Fix the PCIe regulator, make it always on > Fix the polarity of SD2 WP and CD lines, make them active low. > Drop the simple-bus for regulators, put them in /soc instead. > Configure the mux of all pins instead of depending on bootloader. > Change license to Dual X11/GPLv2+ (Acked by Sean) > Sort the nodes alphabetically. > > V3: Drop the spidev node > Drop the fsl,mode = "i2s-slave"; > Move regulators into / > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 760a737..9eb8fa8 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -325,6 +325,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > imx6q-hummingboard.dtb \ > imx6q-nitrogen6x.dtb \ > imx6q-nitrogen6_max.dtb \ > + imx6q-novena.dtb \ > imx6q-phytec-pbab01.dtb \ > imx6q-rex-pro.dtb \ > imx6q-sabreauto.dtb \ > diff --git a/arch/arm/boot/dts/imx6q-novena.dts b/arch/arm/boot/dts/imx6q-novena.dts > new file mode 100644 > index 0000000..a6b179e > --- /dev/null > +++ b/arch/arm/boot/dts/imx6q-novena.dts > @@ -0,0 +1,846 @@ > +/* > + * Copyright 2015 Sutajio Ko-Usagi PTE LTD > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of > + * the License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * You should have received a copy of the GNU General Public > + * License along with this file; if not, write to the Free > + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, > + * MA 02110-1301 USA > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + * > + */ > + > +/dts-v1/; > +#include "imx6q.dtsi" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +/ { > + model = "Kosagi Novena Dual/Quad"; > + compatible = "kosagi,imx6q-novena", "fsl,imx6q"; > + > + memory { > + reg = <0x10000000 0xefffffff>; > + }; > + > + chosen { > + stdout-path = &uart2; > + }; > + > + backlight: backlight { > + compatible = "pwm-backlight"; > + pwms = <&pwm1 0 10000000>; > + Drop the new line. > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_backlight_novena>; > + power-supply = <®_lvds_lcd>; > + Ditto > + brightness-levels = <0 3 6 12 16 24 32 48 64 96 128 192 255>; > + default-brightness-level = <12>; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gpio_keys_novena>; > + > + user-button { > + label = "User Button"; > + gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_POWER>; > + }; > + > + lid { > + label = "Lid"; > + gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; > + linux,input-type = <5>; /* EV_SW */ > + linux,code = <0>; /* SW_LID */ > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_leds_novena>; > + > + heartbeat { > + label = "novena:white:panel"; > + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "default-on"; > + }; > + }; > + > + panel: panel { > + compatible = "innolux,n133hse-ea1", "simple-panel"; > + backlight = <&backlight>; > + }; > + > + reg_2p5v: 2p5v { > + compatible = "regulator-fixed"; > + regulator-name = "2P5V"; > + regulator-min-microvolt = <2500000>; > + regulator-max-microvolt = <2500000>; > + regulator-always-on; > + }; > + > + reg_3p3v: 3p3v { > + compatible = "regulator-fixed"; > + regulator-name = "3P3V"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + reg_audio_codec: es8328-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "es8328-power"; > + regulator-boot-on; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + startup-delay-us = <400000>; > + gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_display: display-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "lcd-display-power"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + startup-delay-us = <200000>; > + gpio = <&gpio5 28 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_lvds_lcd: lcd-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "lcd-lvds-power"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_pcie: pcie-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "pcie-bus-power"; > + regulator-min-microvolt = <1500000>; > + regulator-max-microvolt = <1500000>; > + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-always-on; > + }; > + > + reg_sata: sata-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "sata-power"; > + regulator-boot-on; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + startup-delay-us = <10000>; > + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_usb_otg_vbus: usb_otg_vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb_otg_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + }; All these regulator nodes are named so arbitrarily. Can we name them a bit consistently, something like regulator-xxx? > + > + sound { > + compatible = "fsl,imx-audio-es8328"; > + model = "imx-audio-es8328"; > + ssi-controller = <&ssi1>; > + audio-codec = <&codec>; > + audio-amp-supply = <®_audio_codec>; > + jack-gpio = <&gpio5 15 GPIO_ACTIVE_HIGH>; > + audio-routing = > + "Speaker", "LOUT2", > + "Speaker", "ROUT2", > + "Speaker", "audio-amp", > + "Headphone", "ROUT1", > + "Headphone", "LOUT1", > + "LINPUT1", "Mic Jack", > + "RINPUT1", "Mic Jack", > + "Mic Jack", "Mic Bias"; > + mux-int-port = <0x1>; > + mux-ext-port = <0x3>; > + }; > +}; > + > +&audmux { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_audmux_novena>; > + status = "okay"; > +}; > + > +&ecspi3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ecspi3_novena>; > + fsl,spi-num-chipselects = <3>; > + status = "okay"; > +}; > + > +&fec { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_enet_novena>; > + phy-mode = "rgmii"; > + phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; > + rxc-skew-ps = <3000>; > + rxdv-skew-ps = <0>; > + txc-skew-ps = <3000>; > + txen-skew-ps = <0>; > + rxd0-skew-ps = <0>; > + rxd1-skew-ps = <0>; > + rxd2-skew-ps = <0>; > + rxd3-skew-ps = <0>; > + txd0-skew-ps = <3000>; > + txd1-skew-ps = <3000>; > + txd2-skew-ps = <3000>; > + txd3-skew-ps = <3000>; > + status = "okay"; > +}; > + > +&hdmi { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hdmi_novena>; > + ddc-i2c-bus = <&i2c2>; > + status = "okay"; > +}; > + > +&i2c1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1_novena>; > + status = "okay"; > + > + accel: mma8452 at 1c { > + compatible = "fsl,mma8452"; > + reg = <0x1c>; > + }; > + > + rtc: pcf8523 at 68 { > + compatible = "nxp,pcf8523"; > + reg = <0x68>; > + }; > + > + sbs_battery: bq20z75 at 0b { > + compatible = "sbs,sbs-battery"; > + reg = <0x0b>; > + sbs,i2c-retry-count = <50>; > + }; > + > + touch: stmpe811 at 44 { > + compatible = "st,stmpe811"; > + reg = <0x44>; > + #address-cells = <1>; > + #size-cells = <0>; > + irq-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; > + id = <0>; > + blocks = <0x5>; > + irq-trigger = <0x1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_stmpe_novena>; > + vio-supply = <®_3p3v>; > + vcc-supply = <®_3p3v>; > + > + stmpe_touchscreen { > + compatible = "st,stmpe-ts"; > + st,sample-time = <4>; > + st,mod-12b = <1>; > + st,ref-sel = <0>; > + st,adc-freq = <1>; > + st,ave-ctrl = <1>; > + st,touch-det-delay = <2>; > + st,settling = <2>; > + st,fraction-z = <7>; > + st,i-drive = <1>; > + }; > + }; > +}; > + > +&i2c2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2_novena>; > + status = "okay"; > + > + pmic: pfuze100 at 08 { > + compatible = "fsl,pfuze100"; > + reg = <0x08>; > + > + regulators { > + sw1a_reg: sw1ab { > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <1875000>; > + regulator-boot-on; > + regulator-always-on; > + regulator-ramp-delay = <6250>; > + }; > + > + sw1c_reg: sw1c { > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <1875000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw2_reg: sw2 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw3a_reg: sw3a { > + regulator-min-microvolt = <400000>; > + regulator-max-microvolt = <1975000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw3b_reg: sw3b { > + regulator-min-microvolt = <400000>; > + regulator-max-microvolt = <1975000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw4_reg: sw4 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + swbst_reg: swbst { > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5150000>; > + regulator-boot-on; > + }; > + > + snvs_reg: vsnvs { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <3000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vref_reg: vrefddr { > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vgen1_reg: vgen1 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1550000>; > + }; > + > + vgen2_reg: vgen2 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1550000>; > + }; > + > + vgen3_reg: vgen3 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + vgen4_reg: vgen4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vgen5_reg: vgen5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vgen6_reg: vgen6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + }; > + }; > +}; > + > +&i2c3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3_novena>; > + status = "okay"; > + > + codec: es8328 at 11 { > + compatible = "everest,es8328"; > + reg = <0x11>; > + DVDD-supply = <®_audio_codec>; > + AVDD-supply = <®_audio_codec>; > + PVDD-supply = <®_audio_codec>; > + HPVDD-supply = <®_audio_codec>; > + Drop this new line. > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sound_novena>; > + Ditto > + clocks = <&clks IMX6QDL_CLK_CKO1>; > + assigned-clocks = <&clks IMX6QDL_CLK_CKO>, <&clks IMX6QDL_CLK_CKO1_SEL>, <&clks IMX6QDL_CLK_PLL4_AUDIO>, <&clks IMX6QDL_CLK_CKO1>; > + assigned-clock-parents = <&clks IMX6QDL_CLK_CKO1>, <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>, <&clks IMX6QDL_CLK_OSC>, <&clks IMX6QDL_CLK_CKO1_PODF>; Please wrap these long lines a bit. > + assigned-clock-rates = <0 0 722534400 22579200>; > + }; > +}; > + > +&iomuxc { I suggest you put the &iomuxc node at the bottom of the file to make it easier to read the file. > + audmux { With commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without function nodes) in place, all these function nodes can just be saved to reduce one level of indentation. > + pinctrl_audmux_novena: audmuxgrp-novena { > + fsl,pins = < > + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 > + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 > + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 > + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 > + >; > + }; > + }; > + > + backlight { > + pinctrl_backlight_novena: backlightgrp-novena { > + fsl,pins = < > + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0 > + MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x1b0b1 > + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b1 > + >; > + }; > + }; > + > + ecspi3 { > + pinctrl_ecspi3_novena: ecspi3grp-novena { > + fsl,pins = < > + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1 > + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1 > + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1 > + >; > + }; > + }; > + > + enet { > + pinctrl_enet_novena: enetgrp-novena { > + fsl,pins = < > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 > + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b020 > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b028 > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b028 > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b028 > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b028 > + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b028 > + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 > + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 > + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 > + Drop this new line. > + /* Ethernet reset */ > + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b1 > + >; > + }; > + }; > + > + fpga { > + pinctrl_fpga_gpio: fpgagpiogrp-novena { > + fsl,pins = < > + /* FPGA power */ > + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b1 > + Ditto > + /* Reset */ > + MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b1 Ditto > + > + /* FPGA GPIOs */ > + MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x1b0b1 > + MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x1b0b1 > + MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x1b0b1 > + MX6QDL_PAD_EIM_DA3__GPIO3_IO03 0x1b0b1 > + MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x1b0b1 > + MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x1b0b1 > + MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x1b0b1 > + MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x1b0b1 > + MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x1b0b1 > + MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x1b0b1 > + MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x1b0b1 > + MX6QDL_PAD_EIM_DA11__GPIO3_IO11 0x1b0b1 > + MX6QDL_PAD_EIM_DA12__GPIO3_IO12 0x1b0b1 > + MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x1b0b1 > + MX6QDL_PAD_EIM_DA14__GPIO3_IO14 0x1b0b1 > + MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x1b0b1 > + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b0b1 > + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b1 > + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 > + MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b1 > + MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b1 > + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b1 > + MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x1b0b1 > + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x1b0b1 > + MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x1b0b1 > + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b1 > + >; > + }; > + > + pinctrl_fpga_eim: fpgaeimgrp-novena { > + fsl,pins = < > + /* FPGA power */ > + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b1 > + > + /* Reset */ > + MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b1 > + Ditto > + /* FPGA GPIOs */ > + MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0f1 > + MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0f1 > + MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0f1 > + MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0f1 > + MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0f1 > + MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0f1 > + MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0f1 > + MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0f1 > + MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0f1 > + MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0f1 > + MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0f1 > + MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0f1 > + MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0f1 > + MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0f1 > + MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0f1 > + MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0f1 > + MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0f1 > + MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0f1 > + MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0f1 > + MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0f1 > + MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0f1 > + MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0f1 > + MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0f1 > + MX6QDL_PAD_EIM_RW__EIM_RW 0xb0f1 > + MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb0f1 > + MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0f1 > + >; > + }; > + }; > + > + gpio_keys { > + pinctrl_gpio_keys_novena: gpiokeysgrp-novena { > + fsl,pins = < > + /* User button */ > + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b0b0 > + > + /* PCIe Wakeup */ > + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1f0e0 > + Ditto > + /* Lid switch */ > + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0 > + >; > + }; > + }; > + > + hdmi { > + pinctrl_hdmi_novena: hdmigrp-novena { > + fsl,pins = < > + MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0 > + MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x1b0b1 > + >; > + }; > + }; > + > + i2c1 { > + pinctrl_i2c1_novena: i2c1grp-novena { > + fsl,pins = < > + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 > + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 > + >; > + }; > + }; > + > + i2c2 { > + pinctrl_i2c2_novena: i2c2grp-novena { > + fsl,pins = < > + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1 > + MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1 > + >; > + }; > + }; > + > + i2c3 { > + pinctrl_i2c3_novena: i2c3grp-novena { > + fsl,pins = < > + MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1 > + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 > + >; > + }; > + }; > + > + kpp-keys { > + pinctrl_kpp_novena: kppgrp-novena { > + fsl,pins = < > + /* Front panel button */ > + MX6QDL_PAD_KEY_ROW1__KEY_ROW1 0x1b0b1 > + Ditto > + /* Fake column driver, not connected */ > + MX6QDL_PAD_KEY_COL1__KEY_COL1 0x1b0b1 > + >; > + }; > + }; > + > + leds { > + pinctrl_leds_novena: ledsgrp-novena { > + fsl,pins = < > + MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x1b0b1 > + >; > + }; > + }; > + > + pcie { > + pinctrl_pcie_novena: pciegrp-novena { > + fsl,pins = < > + /* Reset */ > + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b1 > + > + /* Power On */ > + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b1 > + Ditto > + /* Wifi kill */ > + MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x1b0b1 > + >; > + }; > + }; > + > + sata { > + pinctrl_sata_novena: satagrp-novena { > + fsl,pins = < > + MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x1b0b1 > + >; > + }; > + }; > + > + senoko { > + pinctrl_senoko_novena: senokogrp-novena { > + fsl,pins = < > + /* Senoko IRQ line */ > + MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x13048 > + Ditto > + /* Senoko reset line */ > + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1b0b1 > + >; > + }; > + }; > + > + sound { > + pinctrl_sound_novena: soundgrp-novena { > + fsl,pins = < > + /* Audio power regulator */ > + MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x1b0b1 > + > + /* Headphone plug */ > + MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x1b0b1 > + Ditto > + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000b0 > + >; > + }; > + }; > + > + ts { > + pinctrl_stmpe_novena: stmpegrp-novena { > + fsl,pins = < > + /* Touchscreen interrupt */ > + MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1b0b1 > + >; > + }; > + }; > + > + uart2 { > + pinctrl_uart2_novena: uart2grp-novena { > + fsl,pins = < > + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 > + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 > + >; > + }; > + }; > + > + uart3 { > + pinctrl_uart3_novena: uart3grp-novena { > + fsl,pins = < > + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 > + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 > + >; > + }; > + }; Have a new line between nodes. > + uart4 { > + pinctrl_uart4_novena: uart4grp-novena { > + fsl,pins = < > + MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1 > + MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1 > + >; > + }; > + }; > + > + usbotg { > + pinctrl_usbotg_novena: usbotggrp-novena { > + fsl,pins = < > + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 > + >; > + }; > + }; > + > + usdhc2 { > + pinctrl_usdhc2_novena: usdhc2grp-novena { > + fsl,pins = < > + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170f9 > + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100f9 > + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9 > + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9 > + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9 > + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170f9 > + > + /* Write protect */ > + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b1 > + Drop these new lines. > + /* Card detect */ > + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b1 > + >; > + }; > + }; > + > + usdhc3 { > + pinctrl_usdhc3_novena: usdhc3grp-novena { > + fsl,pins = < > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9 > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9 > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9 > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9 > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9 > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9 > + >; > + }; > + }; > +}; > + > +&kpp { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_kpp_novena>; > + linux,keymap = < > + MATRIX_KEY(1, 1, KEY_CONFIG) > + >; > + status = "okay"; > +}; > + > +&ldb { > + fsl,dual-channel; > + status = "okay"; Have a new between property list and sub-node. Shawn > + lvds-channel at 0 { > + fsl,data-mapping = "jeida"; > + fsl,data-width = <24>; > + fsl,panel = <&panel>; > + status = "okay"; > + }; > +}; > + > +&pcie { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pcie_novena>; > + reset-gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>; > + status = "okay"; > +}; > + > +&sata { > + target-supply = <®_sata>; > + fsl,transmit-level-mV = <1025>; > + fsl,transmit-boost-mdB = <0>; > + fsl,transmit-atten-16ths = <8>; > + status = "okay"; > +}; > + > +&ssi1 { > + status = "okay"; > +}; > + > +&uart2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2_novena>; > + status = "okay"; > +}; > + > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3_novena>; > + status = "okay"; > +}; > + > +&uart4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart4_novena>; > + status = "okay"; > +}; > + > +&usbotg { > + vbus-supply = <®_usb_otg_vbus>; > + dr_mode = "otg"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg_novena>; > + disable-over-current; > + status = "okay"; > +}; > + > +&usbh1 { > + vbus-supply = <&swbst_reg>; > + status = "okay"; > +}; > + > +&usdhc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc2_novena>; > + cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; > + wp-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; > + bus-width = <4>; > + status = "okay"; > +}; > + > +&usdhc3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc3_novena>; > + bus-width = <4>; > + non-removable; > + status = "okay"; > +}; > -- > 2.1.4 > > ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V3 2/2] ARM: dts: imx6q: add Novena board 2015-12-02 7:53 ` Shawn Guo @ 2015-12-02 15:41 ` Marek Vasut 2015-12-11 11:07 ` Shawn Guo 0 siblings, 1 reply; 22+ messages in thread From: Marek Vasut @ 2015-12-02 15:41 UTC (permalink / raw) To: linux-arm-kernel On Wednesday, December 02, 2015 at 08:53:05 AM, Shawn Guo wrote: > On Sat, Nov 28, 2015 at 03:47:04PM +0100, Marek Vasut wrote: > > From: Sean Cross <xobs@kosagi.com> > > > > Novena is an open-hardware laptop/desktop/bare board. > > > > See http://www.kosagi.com/w/index.php?title=Novena_Main_Page > > > > Signed-off-by: Sean Cross <xobs@kosagi.com> > > Signed-off-by: Marek Vasut <marex@denx.de> > > Cc: Fabio Estevam <fabio.estevam@freescale.com> > > Cc: Lucas Stach <l.stach@pengutronix.de> > > Cc: Sean Cross <xobs@kosagi.com> > > Cc: Shawn Guo <shawnguo@kernel.org> > > Looks pretty good. Some minor comments are below. Most of them are > format/style nits. Thanks > > --- > > > > arch/arm/boot/dts/Makefile | 1 + > > arch/arm/boot/dts/imx6q-novena.dts | 846 > > +++++++++++++++++++++++++++++++++++++ 2 files changed, 847 > > insertions(+) > > create mode 100644 arch/arm/boot/dts/imx6q-novena.dts [...] > > + reg_sata: sata-regulator { > > + compatible = "regulator-fixed"; > > + regulator-name = "sata-power"; > > + regulator-boot-on; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + startup-delay-us = <10000>; > > + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; > > + enable-active-high; > > + }; > > + > > + reg_usb_otg_vbus: usb_otg_vbus { > > + compatible = "regulator-fixed"; > > + regulator-name = "usb_otg_vbus"; > > + regulator-min-microvolt = <5000000>; > > + regulator-max-microvolt = <5000000>; > > + enable-active-high; > > + }; > > All these regulator nodes are named so arbitrarily. Can we name them a > bit consistently, something like regulator-xxx? All of them are named like this (well, but the otg_vbus, I can fix that) reg_something: something-regulator {} What do you want to see here ? [...] > > + assigned-clock-rates = <0 0 722534400 22579200>; > > + }; > > +}; > > + > > +&iomuxc { > > I suggest you put the &iomuxc node at the bottom of the file to make it > easier to read the file. > > > + audmux { > > With commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without function > nodes) in place, all these function nodes can just be saved to reduce one > level of indentation. OK, that's a good change. > > + pinctrl_audmux_novena: audmuxgrp-novena { > > + fsl,pins = < > > + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 > > + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 > > + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 > > + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 > > + >; > > + }; > > + }; [...] ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V3 2/2] ARM: dts: imx6q: add Novena board 2015-12-02 15:41 ` Marek Vasut @ 2015-12-11 11:07 ` Shawn Guo 2015-12-12 3:25 ` Marek Vasut 2015-12-12 3:27 ` [PATCH V4 " Marek Vasut 0 siblings, 2 replies; 22+ messages in thread From: Shawn Guo @ 2015-12-11 11:07 UTC (permalink / raw) To: linux-arm-kernel On Wed, Dec 02, 2015 at 04:41:31PM +0100, Marek Vasut wrote: > On Wednesday, December 02, 2015 at 08:53:05 AM, Shawn Guo wrote: > > On Sat, Nov 28, 2015 at 03:47:04PM +0100, Marek Vasut wrote: > > > + reg_usb_otg_vbus: usb_otg_vbus { > > > + compatible = "regulator-fixed"; > > > + regulator-name = "usb_otg_vbus"; > > > + regulator-min-microvolt = <5000000>; > > > + regulator-max-microvolt = <5000000>; > > > + enable-active-high; > > > + }; > > > > All these regulator nodes are named so arbitrarily. Can we name them a > > bit consistently, something like regulator-xxx? > > All of them are named like this (well, but the otg_vbus, I can fix that) > > reg_something: something-regulator {} > > What do you want to see here ? reg_something: regulator-something {} Shawn ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V3 2/2] ARM: dts: imx6q: add Novena board 2015-12-11 11:07 ` Shawn Guo @ 2015-12-12 3:25 ` Marek Vasut 2015-12-12 3:27 ` [PATCH V4 " Marek Vasut 1 sibling, 0 replies; 22+ messages in thread From: Marek Vasut @ 2015-12-12 3:25 UTC (permalink / raw) To: linux-arm-kernel On Friday, December 11, 2015 at 12:07:00 PM, Shawn Guo wrote: > On Wed, Dec 02, 2015 at 04:41:31PM +0100, Marek Vasut wrote: > > On Wednesday, December 02, 2015 at 08:53:05 AM, Shawn Guo wrote: > > > On Sat, Nov 28, 2015 at 03:47:04PM +0100, Marek Vasut wrote: > > > > + reg_usb_otg_vbus: usb_otg_vbus { > > > > + compatible = "regulator-fixed"; > > > > + regulator-name = "usb_otg_vbus"; > > > > + regulator-min-microvolt = <5000000>; > > > > + regulator-max-microvolt = <5000000>; > > > > + enable-active-high; > > > > + }; > > > > > > All these regulator nodes are named so arbitrarily. Can we name them a > > > bit consistently, something like regulator-xxx? > > > > All of them are named like this (well, but the otg_vbus, I can fix that) > > > > reg_something: something-regulator {} > > > > What do you want to see here ? > > reg_something: regulator-something {} OK, let me send a V4. Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V4 2/2] ARM: dts: imx6q: add Novena board 2015-12-11 11:07 ` Shawn Guo 2015-12-12 3:25 ` Marek Vasut @ 2015-12-12 3:27 ` Marek Vasut 2015-12-14 1:38 ` Shawn Guo 1 sibling, 1 reply; 22+ messages in thread From: Marek Vasut @ 2015-12-12 3:27 UTC (permalink / raw) To: linux-arm-kernel From: Sean Cross <xobs@kosagi.com> Novena is an open-hardware laptop/desktop/bare board. See http://www.kosagi.com/w/index.php?title=Novena_Main_Page Signed-off-by: Sean Cross <xobs@kosagi.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Sean Cross <xobs@kosagi.com> Cc: Shawn Guo <shawnguo@kernel.org> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6q-novena.dts | 789 +++++++++++++++++++++++++++++++++++++ 2 files changed, 790 insertions(+) create mode 100644 arch/arm/boot/dts/imx6q-novena.dts V2: Fix the PCIe regulator, make it always on Fix the polarity of SD2 WP and CD lines, make them active low. Drop the simple-bus for regulators, put them in /soc instead. Configure the mux of all pins instead of depending on bootloader. Change license to Dual X11/GPLv2+ (Acked by Sean) Sort the nodes alphabetically. V3: Drop the spidev node Drop the fsl,mode = "i2s-slave"; Move regulators into / V4: Move iomux node to the end of the file Drop the first level of functions from iomux Tweak the names of the regulator nodes to reg_nnn: regulator-nnn {}, Remove various newlines Formatting fixes diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 0fe130e..ba6c6d7 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -325,6 +325,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-hummingboard.dtb \ imx6q-nitrogen6x.dtb \ imx6q-nitrogen6_max.dtb \ + imx6q-novena.dtb \ imx6q-phytec-pbab01.dtb \ imx6q-rex-pro.dtb \ imx6q-sabreauto.dtb \ diff --git a/arch/arm/boot/dts/imx6q-novena.dts b/arch/arm/boot/dts/imx6q-novena.dts new file mode 100644 index 0000000..0dea08a --- /dev/null +++ b/arch/arm/boot/dts/imx6q-novena.dts @@ -0,0 +1,789 @@ +/* + * Copyright 2015 Sutajio Ko-Usagi PTE LTD + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this file; if not, write to the Free + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "Kosagi Novena Dual/Quad"; + compatible = "kosagi,imx6q-novena", "fsl,imx6q"; + + memory { + reg = <0x10000000 0xefffffff>; + }; + + chosen { + stdout-path = &uart2; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 10000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_backlight_novena>; + power-supply = <®_lvds_lcd>; + brightness-levels = <0 3 6 12 16 24 32 48 64 96 128 192 255>; + default-brightness-level = <12>; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys_novena>; + + user-button { + label = "User Button"; + gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + }; + + lid { + label = "Lid"; + gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; + linux,input-type = <5>; /* EV_SW */ + linux,code = <0>; /* SW_LID */ + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds_novena>; + + heartbeat { + label = "novena:white:panel"; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + }; + + panel: panel { + compatible = "innolux,n133hse-ea1", "simple-panel"; + backlight = <&backlight>; + }; + + reg_2p5v: regulator-2p5v { + compatible = "regulator-fixed"; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_audio_codec: regulator-audio-codec { + compatible = "regulator-fixed"; + regulator-name = "es8328-power"; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + startup-delay-us = <400000>; + gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_display: regulator-display { + compatible = "regulator-fixed"; + regulator-name = "lcd-display-power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <200000>; + gpio = <&gpio5 28 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_lvds_lcd: regulator-lvds-lcd { + compatible = "regulator-fixed"; + regulator-name = "lcd-lvds-power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_pcie: regulator-pcie { + compatible = "regulator-fixed"; + regulator-name = "pcie-bus-power"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + reg_sata: regulator-sata { + compatible = "regulator-fixed"; + regulator-name = "sata-power"; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <10000>; + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_otg_vbus: regulator-usb-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + }; + + sound { + compatible = "fsl,imx-audio-es8328"; + model = "imx-audio-es8328"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-amp-supply = <®_audio_codec>; + jack-gpio = <&gpio5 15 GPIO_ACTIVE_HIGH>; + audio-routing = + "Speaker", "LOUT2", + "Speaker", "ROUT2", + "Speaker", "audio-amp", + "Headphone", "ROUT1", + "Headphone", "LOUT1", + "LINPUT1", "Mic Jack", + "RINPUT1", "Mic Jack", + "Mic Jack", "Mic Bias"; + mux-int-port = <0x1>; + mux-ext-port = <0x3>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux_novena>; + status = "okay"; +}; + +&ecspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3_novena>; + fsl,spi-num-chipselects = <3>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_novena>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + rxc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + txc-skew-ps = <3000>; + txen-skew-ps = <0>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txd0-skew-ps = <3000>; + txd1-skew-ps = <3000>; + txd2-skew-ps = <3000>; + txd3-skew-ps = <3000>; + status = "okay"; +}; + +&hdmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hdmi_novena>; + ddc-i2c-bus = <&i2c2>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_novena>; + status = "okay"; + + accel: mma8452 at 1c { + compatible = "fsl,mma8452"; + reg = <0x1c>; + }; + + rtc: pcf8523 at 68 { + compatible = "nxp,pcf8523"; + reg = <0x68>; + }; + + sbs_battery: bq20z75 at 0b { + compatible = "sbs,sbs-battery"; + reg = <0x0b>; + sbs,i2c-retry-count = <50>; + }; + + touch: stmpe811 at 44 { + compatible = "st,stmpe811"; + reg = <0x44>; + #address-cells = <1>; + #size-cells = <0>; + irq-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; + id = <0>; + blocks = <0x5>; + irq-trigger = <0x1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_stmpe_novena>; + vio-supply = <®_3p3v>; + vcc-supply = <®_3p3v>; + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + st,sample-time = <4>; + st,mod-12b = <1>; + st,ref-sel = <0>; + st,adc-freq = <1>; + st,ave-ctrl = <1>; + st,touch-det-delay = <2>; + st,settling = <2>; + st,fraction-z = <7>; + st,i-drive = <1>; + }; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2_novena>; + status = "okay"; + + pmic: pfuze100 at 08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + reg_sw1a: regulator-sw1a { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + reg_sw1c: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_sw2: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_sw3a: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_sw3b: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_sw4: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + reg_swbst: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + regulator-boot-on; + }; + + reg_snvs: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vref: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + reg_vgen1: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + reg_vgen2: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + reg_vgen3: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + reg_vgen4: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_vgen5: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_vgen6: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3_novena>; + status = "okay"; + + codec: es8328 at 11 { + compatible = "everest,es8328"; + reg = <0x11>; + DVDD-supply = <®_audio_codec>; + AVDD-supply = <®_audio_codec>; + PVDD-supply = <®_audio_codec>; + HPVDD-supply = <®_audio_codec>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sound_novena>; + clocks = <&clks IMX6QDL_CLK_CKO1>; + assigned-clocks = <&clks IMX6QDL_CLK_CKO>, + <&clks IMX6QDL_CLK_CKO1_SEL>, + <&clks IMX6QDL_CLK_PLL4_AUDIO>, + <&clks IMX6QDL_CLK_CKO1>; + assigned-clock-parents = <&clks IMX6QDL_CLK_CKO1>, + <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>, + <&clks IMX6QDL_CLK_OSC>, + <&clks IMX6QDL_CLK_CKO1_PODF>; + assigned-clock-rates = <0 0 722534400 22579200>; + }; +}; + +&kpp { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp_novena>; + linux,keymap = < + MATRIX_KEY(1, 1, KEY_CONFIG) + >; + status = "okay"; +}; + +&ldb { + fsl,dual-channel; + status = "okay"; + + lvds-channel at 0 { + fsl,data-mapping = "jeida"; + fsl,data-width = <24>; + fsl,panel = <&panel>; + status = "okay"; + }; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie_novena>; + reset-gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&sata { + target-supply = <®_sata>; + fsl,transmit-level-mV = <1025>; + fsl,transmit-boost-mdB = <0>; + fsl,transmit-atten-16ths = <8>; + status = "okay"; +}; + +&ssi1 { + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2_novena>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3_novena>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4_novena>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + dr_mode = "otg"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg_novena>; + disable-over-current; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_swbst>; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2_novena>; + cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; + bus-width = <4>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3_novena>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&iomuxc { + pinctrl_audmux_novena: audmuxgrp-novena { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_backlight_novena: backlightgrp-novena { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0 + MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x1b0b1 + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b1 + >; + }; + + pinctrl_ecspi3_novena: ecspi3grp-novena { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1 + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1 + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1 + >; + }; + + pinctrl_enet_novena: enetgrp-novena { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b020 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b028 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b028 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b028 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b028 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b028 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + /* Ethernet reset */ + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b1 + >; + }; + + pinctrl_fpga_gpio: fpgagpiogrp-novena { + fsl,pins = < + /* FPGA power */ + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b1 + /* Reset */ + MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b1 + /* FPGA GPIOs */ + MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x1b0b1 + MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x1b0b1 + MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x1b0b1 + MX6QDL_PAD_EIM_DA3__GPIO3_IO03 0x1b0b1 + MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x1b0b1 + MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x1b0b1 + MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x1b0b1 + MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x1b0b1 + MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x1b0b1 + MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x1b0b1 + MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x1b0b1 + MX6QDL_PAD_EIM_DA11__GPIO3_IO11 0x1b0b1 + MX6QDL_PAD_EIM_DA12__GPIO3_IO12 0x1b0b1 + MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x1b0b1 + MX6QDL_PAD_EIM_DA14__GPIO3_IO14 0x1b0b1 + MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x1b0b1 + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b0b1 + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b1 + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 + MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b1 + MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b1 + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b1 + MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x1b0b1 + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x1b0b1 + MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x1b0b1 + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b1 + >; + }; + + pinctrl_fpga_eim: fpgaeimgrp-novena { + fsl,pins = < + /* FPGA power */ + MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b1 + /* Reset */ + MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1b0b1 + /* FPGA GPIOs */ + MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0f1 + MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0f1 + MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0f1 + MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0f1 + MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0f1 + MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0f1 + MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0f1 + MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0f1 + MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0f1 + MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0f1 + MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0f1 + MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0f1 + MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0f1 + MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0f1 + MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0f1 + MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0f1 + MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0f1 + MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0f1 + MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0f1 + MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0f1 + MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0f1 + MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0f1 + MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0f1 + MX6QDL_PAD_EIM_RW__EIM_RW 0xb0f1 + MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb0f1 + MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0f1 + >; + }; + + pinctrl_gpio_keys_novena: gpiokeysgrp-novena { + fsl,pins = < + /* User button */ + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b0b0 + /* PCIe Wakeup */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1f0e0 + /* Lid switch */ + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0 + >; + }; + + pinctrl_hdmi_novena: hdmigrp-novena { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0 + MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x1b0b1 + >; + }; + + pinctrl_i2c1_novena: i2c1grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2_novena: i2c2grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3_novena: i2c3grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_kpp_novena: kppgrp-novena { + fsl,pins = < + /* Front panel button */ + MX6QDL_PAD_KEY_ROW1__KEY_ROW1 0x1b0b1 + /* Fake column driver, not connected */ + MX6QDL_PAD_KEY_COL1__KEY_COL1 0x1b0b1 + >; + }; + + pinctrl_leds_novena: ledsgrp-novena { + fsl,pins = < + MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x1b0b1 + >; + }; + + pinctrl_pcie_novena: pciegrp-novena { + fsl,pins = < + /* Reset */ + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b1 + /* Power On */ + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b1 + /* Wifi kill */ + MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x1b0b1 + >; + }; + + pinctrl_sata_novena: satagrp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x1b0b1 + >; + }; + + pinctrl_senoko_novena: senokogrp-novena { + fsl,pins = < + /* Senoko IRQ line */ + MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x13048 + /* Senoko reset line */ + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1b0b1 + >; + }; + + pinctrl_sound_novena: soundgrp-novena { + fsl,pins = < + /* Audio power regulator */ + MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x1b0b1 + /* Headphone plug */ + MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x1b0b1 + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000b0 + >; + }; + + pinctrl_stmpe_novena: stmpegrp-novena { + fsl,pins = < + /* Touchscreen interrupt */ + MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1b0b1 + >; + }; + + pinctrl_uart2_novena: uart2grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart3_novena: uart3grp-novena { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart4_novena: uart4grp-novena { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg_novena: usbotggrp-novena { + fsl,pins = < + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc2_novena: usdhc2grp-novena { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170f9 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100f9 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170f9 + /* Write protect */ + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b1 + /* Card detect */ + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b1 + >; + }; + + pinctrl_usdhc3_novena: usdhc3grp-novena { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9 + >; + }; +}; -- 2.1.4 ^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH V4 2/2] ARM: dts: imx6q: add Novena board 2015-12-12 3:27 ` [PATCH V4 " Marek Vasut @ 2015-12-14 1:38 ` Shawn Guo 2015-12-14 3:56 ` Marek Vasut 0 siblings, 1 reply; 22+ messages in thread From: Shawn Guo @ 2015-12-14 1:38 UTC (permalink / raw) To: linux-arm-kernel On Sat, Dec 12, 2015 at 04:27:13AM +0100, Marek Vasut wrote: > From: Sean Cross <xobs@kosagi.com> > > Novena is an open-hardware laptop/desktop/bare board. > > See http://www.kosagi.com/w/index.php?title=Novena_Main_Page > > Signed-off-by: Sean Cross <xobs@kosagi.com> > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Fabio Estevam <fabio.estevam@freescale.com> > Cc: Lucas Stach <l.stach@pengutronix.de> > Cc: Sean Cross <xobs@kosagi.com> > Cc: Shawn Guo <shawnguo@kernel.org> It looks pretty good to me now, except a small question below. > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx6q-novena.dts | 789 +++++++++++++++++++++++++++++++++++++ > 2 files changed, 790 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6q-novena.dts <snip> > +/ { > + model = "Kosagi Novena Dual/Quad"; > + compatible = "kosagi,imx6q-novena", "fsl,imx6q"; > + > + memory { > + reg = <0x10000000 0xefffffff>; What's the trick of having memory size being 0xefffffff? Shawn > + }; > ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V4 2/2] ARM: dts: imx6q: add Novena board 2015-12-14 1:38 ` Shawn Guo @ 2015-12-14 3:56 ` Marek Vasut 2015-12-14 13:53 ` Sergei Shtylyov 0 siblings, 1 reply; 22+ messages in thread From: Marek Vasut @ 2015-12-14 3:56 UTC (permalink / raw) To: linux-arm-kernel On Monday, December 14, 2015 at 02:38:45 AM, Shawn Guo wrote: > On Sat, Dec 12, 2015 at 04:27:13AM +0100, Marek Vasut wrote: > > From: Sean Cross <xobs@kosagi.com> > > > > Novena is an open-hardware laptop/desktop/bare board. > > > > See http://www.kosagi.com/w/index.php?title=Novena_Main_Page > > > > Signed-off-by: Sean Cross <xobs@kosagi.com> > > Signed-off-by: Marek Vasut <marex@denx.de> > > Cc: Fabio Estevam <fabio.estevam@freescale.com> > > Cc: Lucas Stach <l.stach@pengutronix.de> > > Cc: Sean Cross <xobs@kosagi.com> > > Cc: Shawn Guo <shawnguo@kernel.org> > > It looks pretty good to me now, except a small question below. Thanks > > --- > > > > arch/arm/boot/dts/Makefile | 1 + > > arch/arm/boot/dts/imx6q-novena.dts | 789 > > +++++++++++++++++++++++++++++++++++++ 2 files changed, 790 > > insertions(+) > > create mode 100644 arch/arm/boot/dts/imx6q-novena.dts > > <snip> > > > +/ { > > + model = "Kosagi Novena Dual/Quad"; > > + compatible = "kosagi,imx6q-novena", "fsl,imx6q"; > > + > > + memory { > > + reg = <0x10000000 0xefffffff>; > > What's the trick of having memory size being 0xefffffff? That is a typo, should obviously be 0xffffffff , I just tested it on the board. Thanks for spotting it, do you want me to repost a V5 or can you fix it ? Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V4 2/2] ARM: dts: imx6q: add Novena board 2015-12-14 3:56 ` Marek Vasut @ 2015-12-14 13:53 ` Sergei Shtylyov 2015-12-14 14:12 ` Marek Vasut 0 siblings, 1 reply; 22+ messages in thread From: Sergei Shtylyov @ 2015-12-14 13:53 UTC (permalink / raw) To: linux-arm-kernel Hello. On 12/14/2015 6:56 AM, Marek Vasut wrote: >>> From: Sean Cross <xobs@kosagi.com> >>> >>> Novena is an open-hardware laptop/desktop/bare board. >>> >>> See http://www.kosagi.com/w/index.php?title=Novena_Main_Page >>> >>> Signed-off-by: Sean Cross <xobs@kosagi.com> >>> Signed-off-by: Marek Vasut <marex@denx.de> >>> Cc: Fabio Estevam <fabio.estevam@freescale.com> >>> Cc: Lucas Stach <l.stach@pengutronix.de> >>> Cc: Sean Cross <xobs@kosagi.com> >>> Cc: Shawn Guo <shawnguo@kernel.org> >> >> It looks pretty good to me now, except a small question below. > > Thanks > >>> --- >>> >>> arch/arm/boot/dts/Makefile | 1 + >>> arch/arm/boot/dts/imx6q-novena.dts | 789 >>> +++++++++++++++++++++++++++++++++++++ 2 files changed, 790 >>> insertions(+) >>> create mode 100644 arch/arm/boot/dts/imx6q-novena.dts >> >> <snip> >> >>> +/ { >>> + model = "Kosagi Novena Dual/Quad"; >>> + compatible = "kosagi,imx6q-novena", "fsl,imx6q"; >>> + >>> + memory { >>> + reg = <0x10000000 0xefffffff>; >> >> What's the trick of having memory size being 0xefffffff? > That is a typo, should obviously be 0xffffffff , You didn't get it. :-) It' the _size_, not limit. [...] > Best regards, > Marek Vasut MBR, Sergei ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V4 2/2] ARM: dts: imx6q: add Novena board 2015-12-14 13:53 ` Sergei Shtylyov @ 2015-12-14 14:12 ` Marek Vasut 2015-12-14 14:17 ` Fabio Estevam 0 siblings, 1 reply; 22+ messages in thread From: Marek Vasut @ 2015-12-14 14:12 UTC (permalink / raw) To: linux-arm-kernel On Monday, December 14, 2015 at 02:53:42 PM, Sergei Shtylyov wrote: > Hello. > > On 12/14/2015 6:56 AM, Marek Vasut wrote: > >>> From: Sean Cross <xobs@kosagi.com> > >>> > >>> Novena is an open-hardware laptop/desktop/bare board. > >>> > >>> See http://www.kosagi.com/w/index.php?title=Novena_Main_Page > >>> > >>> Signed-off-by: Sean Cross <xobs@kosagi.com> > >>> Signed-off-by: Marek Vasut <marex@denx.de> > >>> Cc: Fabio Estevam <fabio.estevam@freescale.com> > >>> Cc: Lucas Stach <l.stach@pengutronix.de> > >>> Cc: Sean Cross <xobs@kosagi.com> > >>> Cc: Shawn Guo <shawnguo@kernel.org> > >> > >> It looks pretty good to me now, except a small question below. > > > > Thanks > > > >>> --- > >>> > >>> arch/arm/boot/dts/Makefile | 1 + > >>> arch/arm/boot/dts/imx6q-novena.dts | 789 > >>> +++++++++++++++++++++++++++++++++++++ 2 files changed, 790 > >>> insertions(+) > >>> create mode 100644 arch/arm/boot/dts/imx6q-novena.dts > >> > >> <snip> > >> > >>> +/ { > >>> + model = "Kosagi Novena Dual/Quad"; > >>> + compatible = "kosagi,imx6q-novena", "fsl,imx6q"; > >>> + > >>> + memory { > >>> + reg = <0x10000000 0xefffffff>; > >> > >> What's the trick of having memory size being 0xefffffff? > > > > That is a typo, should obviously be 0xffffffff , > > You didn't get it. :-) It' the _size_, not limit. So it was correct from the get-go ? Uh ... Thanks for clarification, I will remember this :) Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V4 2/2] ARM: dts: imx6q: add Novena board 2015-12-14 14:12 ` Marek Vasut @ 2015-12-14 14:17 ` Fabio Estevam 2015-12-14 14:41 ` Marek Vasut 0 siblings, 1 reply; 22+ messages in thread From: Fabio Estevam @ 2015-12-14 14:17 UTC (permalink / raw) To: linux-arm-kernel Hi Marek, On Mon, Dec 14, 2015 at 12:12 PM, Marek Vasut <marex@denx.de> wrote: > So it was correct from the get-go ? Uh ... > > Thanks for clarification, I will remember this :) If you prefer, you can even remove this memory node entry from the dts and let the bootloader pass the correct amount of RAM to the kernel. This is useful when a board has variants in RAM size. Regards, Fabio Estevam ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V4 2/2] ARM: dts: imx6q: add Novena board 2015-12-14 14:17 ` Fabio Estevam @ 2015-12-14 14:41 ` Marek Vasut 2015-12-14 14:45 ` Fabio Estevam 0 siblings, 1 reply; 22+ messages in thread From: Marek Vasut @ 2015-12-14 14:41 UTC (permalink / raw) To: linux-arm-kernel On Monday, December 14, 2015 at 03:17:04 PM, Fabio Estevam wrote: > Hi Marek, Hi! > On Mon, Dec 14, 2015 at 12:12 PM, Marek Vasut <marex@denx.de> wrote: > > So it was correct from the get-go ? Uh ... > > > > Thanks for clarification, I will remember this :) > > If you prefer, you can even remove this memory node entry from the dts > and let the bootloader pass the correct amount of RAM to the kernel. > > This is useful when a board has variants in RAM size. Well that's a good idea, but some sort of sane default should be present anyway, right ? Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V4 2/2] ARM: dts: imx6q: add Novena board 2015-12-14 14:41 ` Marek Vasut @ 2015-12-14 14:45 ` Fabio Estevam 2015-12-14 14:47 ` Marek Vasut 0 siblings, 1 reply; 22+ messages in thread From: Fabio Estevam @ 2015-12-14 14:45 UTC (permalink / raw) To: linux-arm-kernel On Mon, Dec 14, 2015 at 12:41 PM, Marek Vasut <marex@denx.de> wrote: > Well that's a good idea, but some sort of sane default should be present > anyway, right ? No, not needed. The bootloader should pass the correct RAM size. See imx6qdl-hummingboard and imx6qdl-cubox-i.dtsi for a reference, where 'memory' node is not passed. Regards, Fabio Estevam ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V4 2/2] ARM: dts: imx6q: add Novena board 2015-12-14 14:45 ` Fabio Estevam @ 2015-12-14 14:47 ` Marek Vasut 2015-12-15 3:33 ` Marek Vasut 0 siblings, 1 reply; 22+ messages in thread From: Marek Vasut @ 2015-12-14 14:47 UTC (permalink / raw) To: linux-arm-kernel On Monday, December 14, 2015 at 03:45:16 PM, Fabio Estevam wrote: > On Mon, Dec 14, 2015 at 12:41 PM, Marek Vasut <marex@denx.de> wrote: > > Well that's a good idea, but some sort of sane default should be present > > anyway, right ? > > No, not needed. The bootloader should pass the correct RAM size. > > See imx6qdl-hummingboard and imx6qdl-cubox-i.dtsi for a reference, > where 'memory' node is not passed. So, if bootloader does not do the changes to the DT, then what ? (U-Boot does them, so it would work, but I don't think we should depend on that) Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V4 2/2] ARM: dts: imx6q: add Novena board 2015-12-14 14:47 ` Marek Vasut @ 2015-12-15 3:33 ` Marek Vasut 0 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2015-12-15 3:33 UTC (permalink / raw) To: linux-arm-kernel On Monday, December 14, 2015 at 03:47:10 PM, Marek Vasut wrote: > On Monday, December 14, 2015 at 03:45:16 PM, Fabio Estevam wrote: > > On Mon, Dec 14, 2015 at 12:41 PM, Marek Vasut <marex@denx.de> wrote: > > > Well that's a good idea, but some sort of sane default should be > > > present anyway, right ? > > > > No, not needed. The bootloader should pass the correct RAM size. > > > > See imx6qdl-hummingboard and imx6qdl-cubox-i.dtsi for a reference, > > where 'memory' node is not passed. > > So, if bootloader does not do the changes to the DT, then what ? > (U-Boot does them, so it would work, but I don't think we should depend on > that) I just tested that removing the whole memory {} node has no impact. Would you thus prefer a V5 or can you remove that node yourself when applying? Best regards, Marek Vasut ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V2 1/2] devicetree: bindings: Add vendor prefix for Kosagi 2015-11-28 14:47 [PATCH V2 1/2] devicetree: bindings: Add vendor prefix for Kosagi Marek Vasut 2015-11-28 14:47 ` [PATCH V3 2/2] ARM: dts: imx6q: add Novena board Marek Vasut @ 2015-12-14 1:36 ` Shawn Guo 1 sibling, 0 replies; 22+ messages in thread From: Shawn Guo @ 2015-12-14 1:36 UTC (permalink / raw) To: linux-arm-kernel On Sat, Nov 28, 2015 at 03:47:03PM +0100, Marek Vasut wrote: > From: Sean Cross <xobs@kosagi.com> > > Add a vendor prefix for Sutajio Ko-Usagi PTE Ltd., which goes by the > more common name of Kosagi. > > Signed-off-by: Sean Cross <xobs@kosagi.com> > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Rob Herring <robh@kernel.org> Hi Rob, Are you okay with this patch? Shawn > Cc: Shawn Guo <shawnguo@kernel.org> > Cc: Fabio Estevam <fabio.estevam@freescale.com> > --- > Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + > 1 file changed, 1 insertion(+) > > V2: Add my SoB line. > > diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt > index 62ff22f..d3ee06e 100644 > --- a/Documentation/devicetree/bindings/vendor-prefixes.txt > +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt > @@ -124,6 +124,7 @@ jedec JEDEC Solid State Technology Association > karo Ka-Ro electronics GmbH > keymile Keymile GmbH > kinetic Kinetic Technologies > +kosagi Sutajio Ko-Usagi PTE Ltd. > lacie LaCie > lantiq Lantiq Semiconductor > lenovo Lenovo Group Ltd. > -- > 2.1.4 > > ^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH V2 1/2] devicetree: bindings: Add vendor prefix for Kosagi @ 2015-12-18 5:29 Marek Vasut 2015-12-21 13:20 ` Shawn Guo 0 siblings, 1 reply; 22+ messages in thread From: Marek Vasut @ 2015-12-18 5:29 UTC (permalink / raw) To: linux-arm-kernel From: Sean Cross <xobs@kosagi.com> Add a vendor prefix for Sutajio Ko-Usagi PTE Ltd., which goes by the more common name of Kosagi. Signed-off-by: Sean Cross <xobs@kosagi.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Rob Herring <robh@kernel.org> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Fabio Estevam <fabio.estevam@freescale.com> --- Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+) V2: Rebase on top of linux-next diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 38eeaa2..265ec68 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -125,6 +125,7 @@ karo Ka-Ro electronics GmbH keymile Keymile GmbH kinetic Kinetic Technologies kyo Kyocera Corporation +kosagi Sutajio Ko-Usagi PTE Ltd. lacie LaCie lantiq Lantiq Semiconductor lenovo Lenovo Group Ltd. -- 2.1.4 ^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH V2 1/2] devicetree: bindings: Add vendor prefix for Kosagi 2015-12-18 5:29 Marek Vasut @ 2015-12-21 13:20 ` Shawn Guo 0 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2015-12-21 13:20 UTC (permalink / raw) To: linux-arm-kernel On Fri, Dec 18, 2015 at 06:29:49AM +0100, Marek Vasut wrote: > From: Sean Cross <xobs@kosagi.com> > > Add a vendor prefix for Sutajio Ko-Usagi PTE Ltd., which goes by the > more common name of Kosagi. > > Signed-off-by: Sean Cross <xobs@kosagi.com> > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Rob Herring <robh@kernel.org> > Cc: Shawn Guo <shawnguo@kernel.org> > Cc: Fabio Estevam <fabio.estevam@freescale.com> Applied both, thanks. ^ permalink raw reply [flat|nested] 22+ messages in thread
end of thread, other threads:[~2015-12-21 13:20 UTC | newest] Thread overview: 22+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2015-11-28 14:47 [PATCH V2 1/2] devicetree: bindings: Add vendor prefix for Kosagi Marek Vasut 2015-11-28 14:47 ` [PATCH V3 2/2] ARM: dts: imx6q: add Novena board Marek Vasut 2015-11-30 10:19 ` Lucas Stach 2015-11-30 12:21 ` Marek Vasut 2015-11-30 10:57 ` Fabio Estevam 2015-12-02 7:53 ` Shawn Guo 2015-12-02 15:41 ` Marek Vasut 2015-12-11 11:07 ` Shawn Guo 2015-12-12 3:25 ` Marek Vasut 2015-12-12 3:27 ` [PATCH V4 " Marek Vasut 2015-12-14 1:38 ` Shawn Guo 2015-12-14 3:56 ` Marek Vasut 2015-12-14 13:53 ` Sergei Shtylyov 2015-12-14 14:12 ` Marek Vasut 2015-12-14 14:17 ` Fabio Estevam 2015-12-14 14:41 ` Marek Vasut 2015-12-14 14:45 ` Fabio Estevam 2015-12-14 14:47 ` Marek Vasut 2015-12-15 3:33 ` Marek Vasut 2015-12-14 1:36 ` [PATCH V2 1/2] devicetree: bindings: Add vendor prefix for Kosagi Shawn Guo -- strict thread matches above, loose matches on Subject: below -- 2015-12-18 5:29 Marek Vasut 2015-12-21 13:20 ` Shawn Guo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).