* [PATCH 1/6] dma: enable mxs-dma for imx6ul
2016-01-20 12:57 [PATCH 0/6] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
@ 2016-01-20 12:57 ` Lothar Waßmann
2016-01-25 12:10 ` Vinod Koul
2016-01-20 12:57 ` [PATCH 2/6] ARM: dts: imx6: use correct mclk frequency for audio codec Lothar Waßmann
` (4 subsequent siblings)
5 siblings, 1 reply; 13+ messages in thread
From: Lothar Waßmann @ 2016-01-20 12:57 UTC (permalink / raw)
To: linux-arm-kernel
The mxs-dma unit is also available on i.MX6UL. Make it possible to
select it in Kconfig.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
drivers/dma/Kconfig | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
index 79b1390..2516524 100644
--- a/drivers/dma/Kconfig
+++ b/drivers/dma/Kconfig
@@ -341,12 +341,13 @@ config MV_XOR
config MXS_DMA
bool "MXS DMA support"
- depends on SOC_IMX23 || SOC_IMX28 || SOC_IMX6Q
+ depends on SOC_IMX23 || SOC_IMX28 || SOC_IMX6Q || SOC_MX6UL
select STMP_DEVICE
select DMA_ENGINE
help
Support the MXS DMA engine. This engine including APBH-DMA
- and APBX-DMA is integrated into Freescale i.MX23/28/MX6Q/MX6DL chips.
+ and APBX-DMA is integrated into Freescale
+ i.MX23/28/MX6Q/MX6DL/MX6UL chips.
config MX3_IPU
bool "MX3x Image Processing Unit support"
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 1/6] dma: enable mxs-dma for imx6ul
2016-01-20 12:57 ` [PATCH 1/6] dma: enable mxs-dma for imx6ul Lothar Waßmann
@ 2016-01-25 12:10 ` Vinod Koul
2016-02-02 6:23 ` Shawn Guo
0 siblings, 1 reply; 13+ messages in thread
From: Vinod Koul @ 2016-01-25 12:10 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Jan 20, 2016 at 01:57:01PM +0100, Lothar Wa?mann wrote:
> The mxs-dma unit is also available on i.MX6UL. Make it possible to
> select it in Kconfig.
It should be dmaengine:xxx
With that
Acked-by: Vinod Koul <vinod.koul@intel.com>
>
> Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
> ---
> drivers/dma/Kconfig | 5 +++--
> 1 file changed, 3 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
> index 79b1390..2516524 100644
> --- a/drivers/dma/Kconfig
> +++ b/drivers/dma/Kconfig
> @@ -341,12 +341,13 @@ config MV_XOR
>
> config MXS_DMA
> bool "MXS DMA support"
> - depends on SOC_IMX23 || SOC_IMX28 || SOC_IMX6Q
> + depends on SOC_IMX23 || SOC_IMX28 || SOC_IMX6Q || SOC_MX6UL
> select STMP_DEVICE
> select DMA_ENGINE
> help
> Support the MXS DMA engine. This engine including APBH-DMA
> - and APBX-DMA is integrated into Freescale i.MX23/28/MX6Q/MX6DL chips.
> + and APBX-DMA is integrated into Freescale
> + i.MX23/28/MX6Q/MX6DL/MX6UL chips.
>
> config MX3_IPU
> bool "MX3x Image Processing Unit support"
> --
> 2.1.4
>
--
~Vinod
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 1/6] dma: enable mxs-dma for imx6ul
2016-01-25 12:10 ` Vinod Koul
@ 2016-02-02 6:23 ` Shawn Guo
2016-02-08 3:14 ` Vinod Koul
0 siblings, 1 reply; 13+ messages in thread
From: Shawn Guo @ 2016-02-02 6:23 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Jan 25, 2016 at 05:40:43PM +0530, Vinod Koul wrote:
> On Wed, Jan 20, 2016 at 01:57:01PM +0100, Lothar Wa?mann wrote:
> > The mxs-dma unit is also available on i.MX6UL. Make it possible to
> > select it in Kconfig.
>
> It should be dmaengine:xxx
>
> With that
>
> Acked-by: Vinod Koul <vinod.koul@intel.com>
I think this can go separately via dma tree.
Shawn
>
> >
> > Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
> > ---
> > drivers/dma/Kconfig | 5 +++--
> > 1 file changed, 3 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
> > index 79b1390..2516524 100644
> > --- a/drivers/dma/Kconfig
> > +++ b/drivers/dma/Kconfig
> > @@ -341,12 +341,13 @@ config MV_XOR
> >
> > config MXS_DMA
> > bool "MXS DMA support"
> > - depends on SOC_IMX23 || SOC_IMX28 || SOC_IMX6Q
> > + depends on SOC_IMX23 || SOC_IMX28 || SOC_IMX6Q || SOC_MX6UL
> > select STMP_DEVICE
> > select DMA_ENGINE
> > help
> > Support the MXS DMA engine. This engine including APBH-DMA
> > - and APBX-DMA is integrated into Freescale i.MX23/28/MX6Q/MX6DL chips.
> > + and APBX-DMA is integrated into Freescale
> > + i.MX23/28/MX6Q/MX6DL/MX6UL chips.
> >
> > config MX3_IPU
> > bool "MX3x Image Processing Unit support"
> > --
> > 2.1.4
> >
>
> --
> ~Vinod
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 1/6] dma: enable mxs-dma for imx6ul
2016-02-02 6:23 ` Shawn Guo
@ 2016-02-08 3:14 ` Vinod Koul
0 siblings, 0 replies; 13+ messages in thread
From: Vinod Koul @ 2016-02-08 3:14 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Feb 02, 2016 at 02:23:16PM +0800, Shawn Guo wrote:
> On Mon, Jan 25, 2016 at 05:40:43PM +0530, Vinod Koul wrote:
> > On Wed, Jan 20, 2016 at 01:57:01PM +0100, Lothar Wa?mann wrote:
> > > The mxs-dma unit is also available on i.MX6UL. Make it possible to
> > > select it in Kconfig.
> >
> > It should be dmaengine:xxx
> >
> > With that
> >
> > Acked-by: Vinod Koul <vinod.koul@intel.com>
>
> I think this can go separately via dma tree.
Okay, pls resend :)
--
~Vinod
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 2/6] ARM: dts: imx6: use correct mclk frequency for audio codec
2016-01-20 12:57 [PATCH 0/6] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
2016-01-20 12:57 ` [PATCH 1/6] dma: enable mxs-dma for imx6ul Lothar Waßmann
@ 2016-01-20 12:57 ` Lothar Waßmann
2016-02-02 6:31 ` Shawn Guo
2016-01-20 12:57 ` [PATCH 3/6] ARM: dts: imx6qdl-tx6: add ENET_OUT clock to fec node Lothar Waßmann
` (3 subsequent siblings)
5 siblings, 1 reply; 13+ messages in thread
From: Lothar Waßmann @ 2016-01-20 12:57 UTC (permalink / raw)
To: linux-arm-kernel
The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index 13cb7cc..9404668 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -41,7 +41,7 @@
compatible = "fixed-clock";
reg = <0>;
#clock-cells = <0>;
- clock-frequency = <27000000>;
+ clock-frequency = <26000000>;
};
};
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 2/6] ARM: dts: imx6: use correct mclk frequency for audio codec
2016-01-20 12:57 ` [PATCH 2/6] ARM: dts: imx6: use correct mclk frequency for audio codec Lothar Waßmann
@ 2016-02-02 6:31 ` Shawn Guo
0 siblings, 0 replies; 13+ messages in thread
From: Shawn Guo @ 2016-02-02 6:31 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Jan 20, 2016 at 01:57:02PM +0100, Lothar Wa?mann wrote:
> The reference clock for the SGTL5000 is generated by a 26MHz crystal
> oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
> frequency setting in DTB.
>
> Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
Applied, thanks.
> ---
> arch/arm/boot/dts/imx6qdl-tx6.dtsi | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
> index 13cb7cc..9404668 100644
> --- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
> @@ -41,7 +41,7 @@
> compatible = "fixed-clock";
> reg = <0>;
> #clock-cells = <0>;
> - clock-frequency = <27000000>;
> + clock-frequency = <26000000>;
> };
> };
>
> --
> 2.1.4
>
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 3/6] ARM: dts: imx6qdl-tx6: add ENET_OUT clock to fec node
2016-01-20 12:57 [PATCH 0/6] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
2016-01-20 12:57 ` [PATCH 1/6] dma: enable mxs-dma for imx6ul Lothar Waßmann
2016-01-20 12:57 ` [PATCH 2/6] ARM: dts: imx6: use correct mclk frequency for audio codec Lothar Waßmann
@ 2016-01-20 12:57 ` Lothar Waßmann
2016-02-02 6:31 ` Shawn Guo
2016-01-20 12:57 ` [PATCH 4/6] ARM: dts: imx6: change TX6 module names due to new HW revision Lothar Waßmann
` (2 subsequent siblings)
5 siblings, 1 reply; 13+ messages in thread
From: Lothar Waßmann @ 2016-01-20 12:57 UTC (permalink / raw)
To: linux-arm-kernel
ENET_OUT is used as reference clock for the ethernet PHY on the Ka-Ro
TX6 modules. Specify this clock in DTB to let it be managed correctly
by the driver.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index 9404668..5e0afc8 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -227,6 +227,11 @@
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET_REF>,
+ <&clks IMX6QDL_CLK_ENET_REF>;
+ clock-names = "ipg", "ahb", "ptp", "enet_out";
phy-mode = "rmii";
phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_HIGH>;
phy-supply = <®_3v3_etn>;
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 4/6] ARM: dts: imx6: change TX6 module names due to new HW revision
2016-01-20 12:57 [PATCH 0/6] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
` (2 preceding siblings ...)
2016-01-20 12:57 ` [PATCH 3/6] ARM: dts: imx6qdl-tx6: add ENET_OUT clock to fec node Lothar Waßmann
@ 2016-01-20 12:57 ` Lothar Waßmann
2016-02-02 6:36 ` Shawn Guo
2016-01-20 12:57 ` [PATCH 5/6] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
2016-01-20 12:57 ` [PATCH 6/6] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard Lothar Waßmann
5 siblings, 1 reply; 13+ messages in thread
From: Lothar Waßmann @ 2016-01-20 12:57 UTC (permalink / raw)
To: linux-arm-kernel
The second last digit of the Ka-Ro electronics TX-module names denotes
the HW revision of the module. HW rev 1 and 3 of the TX6 modules can
use the same DTB. Change this digit to 'x' to indicate that the DTB
file can be used for both HW revisions.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 10 +-
arch/arm/boot/dts/imx6dl-tx6u-801x.dts | 177 -------------------
arch/arm/boot/dts/imx6dl-tx6u-80xx.dts | 185 ++++++++++++++++++++
arch/arm/boot/dts/imx6dl-tx6u-811x.dts | 150 ----------------
arch/arm/boot/dts/imx6dl-tx6u-81xx.dts | 156 +++++++++++++++++
arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts | 103 -----------
arch/arm/boot/dts/imx6q-tx6q-1010.dts | 177 -------------------
arch/arm/boot/dts/imx6q-tx6q-10x0-comtft.dts | 119 +++++++++++++
arch/arm/boot/dts/imx6q-tx6q-10x0.dts | 191 ++++++++++++++++++++
arch/arm/boot/dts/imx6q-tx6q-1110.dts | 154 -----------------
arch/arm/boot/dts/imx6q-tx6q-11x0.dts | 249 +++++++++++++++++++++++++++
11 files changed, 905 insertions(+), 766 deletions(-)
delete mode 100644 arch/arm/boot/dts/imx6dl-tx6u-801x.dts
create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-80xx.dts
delete mode 100644 arch/arm/boot/dts/imx6dl-tx6u-811x.dts
create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-81xx.dts
delete mode 100644 arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts
delete mode 100644 arch/arm/boot/dts/imx6q-tx6q-1010.dts
create mode 100644 arch/arm/boot/dts/imx6q-tx6q-10x0-comtft.dts
create mode 100644 arch/arm/boot/dts/imx6q-tx6q-10x0.dts
delete mode 100644 arch/arm/boot/dts/imx6q-tx6q-1110.dts
create mode 100644 arch/arm/boot/dts/imx6q-tx6q-11x0.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a4a6d70..5759aac 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -312,8 +312,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \
imx6dl-tx6dl-comtft.dtb \
- imx6dl-tx6u-801x.dtb \
- imx6dl-tx6u-811x.dtb \
+ imx6dl-tx6u-80xx.dtb \
+ imx6dl-tx6u-81xx.dtb \
imx6dl-udoo.dtb \
imx6dl-wandboard.dtb \
imx6dl-wandboard-revb1.dtb \
@@ -342,11 +342,11 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-sabresd.dtb \
imx6q-sbc6x.dtb \
imx6q-tbs2910.dtb \
- imx6q-tx6q-1010.dtb \
- imx6q-tx6q-1010-comtft.dtb \
imx6q-tx6q-1020.dtb \
imx6q-tx6q-1020-comtft.dtb \
- imx6q-tx6q-1110.dtb \
+ imx6q-tx6q-10x0-comtft.dtb \
+ imx6q-tx6q-10x0.dtb \
+ imx6q-tx6q-11x0.dtb \
imx6q-udoo.dtb \
imx6q-wandboard.dtb \
imx6q-wandboard-revb1.dtb
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-801x.dts b/arch/arm/boot/dts/imx6dl-tx6u-801x.dts
deleted file mode 100644
index 5fe465c..0000000
--- a/arch/arm/boot/dts/imx6dl-tx6u-801x.dts
+++ /dev/null
@@ -1,177 +0,0 @@
-/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-tx6.dtsi"
-
-/ {
- model = "Ka-Ro electronics TX6U-801x Module";
- compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
-
- aliases {
- display = &display;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
- power-supply = <®_3v3>;
- /*
- * a poor man's way to create a 1:1 relationship between
- * the PWM value and the actual duty cycle
- */
- brightness-levels = < 0 1 2 3 4 5 6 7 8 9
- 10 11 12 13 14 15 16 17 18 19
- 20 21 22 23 24 25 26 27 28 29
- 30 31 32 33 34 35 36 37 38 39
- 40 41 42 43 44 45 46 47 48 49
- 50 51 52 53 54 55 56 57 58 59
- 60 61 62 63 64 65 66 67 68 69
- 70 71 72 73 74 75 76 77 78 79
- 80 81 82 83 84 85 86 87 88 89
- 90 91 92 93 94 95 96 97 98 99
- 100>;
- default-brightness-level = <50>;
- };
-
- display: display at di0 {
- compatible = "fsl,imx-parallel-display";
- interface-pix-fmt = "rgb24";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_disp0_1>;
- status = "okay";
-
- port {
- display0_in: endpoint {
- remote-endpoint = <&ipu1_di0_disp0>;
- };
- };
-
- display-timings {
- VGA {
- clock-frequency = <25200000>;
- hactive = <640>;
- vactive = <480>;
- hback-porch = <48>;
- hsync-len = <96>;
- hfront-porch = <16>;
- vback-porch = <31>;
- vsync-len = <2>;
- vfront-porch = <12>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
-
- ETV570 {
- clock-frequency = <25200000>;
- hactive = <640>;
- vactive = <480>;
- hback-porch = <114>;
- hsync-len = <30>;
- hfront-porch = <16>;
- vback-porch = <32>;
- vsync-len = <3>;
- vfront-porch = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
-
- ET0350 {
- clock-frequency = <6413760>;
- hactive = <320>;
- vactive = <240>;
- hback-porch = <34>;
- hsync-len = <34>;
- hfront-porch = <20>;
- vback-porch = <15>;
- vsync-len = <3>;
- vfront-porch = <4>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
-
- ET0430 {
- clock-frequency = <9009000>;
- hactive = <480>;
- vactive = <272>;
- hback-porch = <2>;
- hsync-len = <41>;
- hfront-porch = <2>;
- vback-porch = <2>;
- vsync-len = <10>;
- vfront-porch = <2>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
-
- ET0500 {
- clock-frequency = <33264000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <88>;
- hsync-len = <128>;
- hfront-porch = <40>;
- vback-porch = <33>;
- vsync-len = <2>;
- vfront-porch = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
-
- ET0700 { /* same as ET0500 */
- clock-frequency = <33264000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <88>;
- hsync-len = <128>;
- hfront-porch = <40>;
- vback-porch = <33>;
- vsync-len = <2>;
- vfront-porch = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
-
- ETQ570 {
- clock-frequency = <6596040>;
- hactive = <320>;
- vactive = <240>;
- hback-porch = <38>;
- hsync-len = <30>;
- hfront-porch = <30>;
- vback-porch = <16>;
- vsync-len = <3>;
- vfront-porch = <4>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
- };
- };
-};
-
-&ipu1_di0_disp0 {
- remote-endpoint = <&display0_in>;
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-80xx.dts b/arch/arm/boot/dts/imx6dl-tx6u-80xx.dts
new file mode 100644
index 0000000..f6621d6
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6u-80xx.dts
@@ -0,0 +1,185 @@
+/*
+ * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6U-801x/-803x Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &display;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ interface-pix-fmt = "rgb24";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_1>;
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+®_lcd0_pwr {
+ status = "okay";
+};
+
+®_lcd1_pwr {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
deleted file mode 100644
index c275eec..0000000
--- a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
+++ /dev/null
@@ -1,150 +0,0 @@
-/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-tx6.dtsi"
-
-/ {
- model = "Ka-Ro electronics TX6U-811x Module";
- compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
-
- aliases {
- display = &lvds0;
- lvds0 = &lvds0;
- lvds1 = &lvds1;
- };
-
- backlight0: backlight0 {
- compatible = "pwm-backlight";
- pwms = <&pwm2 0 500000 0>;
- power-supply = <®_lcd0_pwr>;
- /*
- * a poor man's way to create a 1:1 relationship between
- * the PWM value and the actual duty cycle
- */
- brightness-levels = < 0 1 2 3 4 5 6 7 8 9
- 10 11 12 13 14 15 16 17 18 19
- 20 21 22 23 24 25 26 27 28 29
- 30 31 32 33 34 35 36 37 38 39
- 40 41 42 43 44 45 46 47 48 49
- 50 51 52 53 54 55 56 57 58 59
- 60 61 62 63 64 65 66 67 68 69
- 70 71 72 73 74 75 76 77 78 79
- 80 81 82 83 84 85 86 87 88 89
- 90 91 92 93 94 95 96 97 98 99
- 100>;
- default-brightness-level = <50>;
- };
-
- backlight1: backlight1 {
- compatible = "pwm-backlight";
- pwms = <&pwm1 0 500000 0>;
- power-supply = <®_lcd1_pwr>;
- /*
- * a poor man's way to create a 1:1 relationship between
- * the PWM value and the actual duty cycle
- */
- brightness-levels = < 0 1 2 3 4 5 6 7 8 9
- 10 11 12 13 14 15 16 17 18 19
- 20 21 22 23 24 25 26 27 28 29
- 30 31 32 33 34 35 36 37 38 39
- 40 41 42 43 44 45 46 47 48 49
- 50 51 52 53 54 55 56 57 58 59
- 60 61 62 63 64 65 66 67 68 69
- 70 71 72 73 74 75 76 77 78 79
- 80 81 82 83 84 85 86 87 88 89
- 90 91 92 93 94 95 96 97 98 99
- 100>;
- default-brightness-level = <50>;
- };
-};
-
-&i2c3 {
- polytouch2: eeti at 04 {
- compatible = "eeti,egalax_ts";
- reg = <0x04>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_eeti>;
- interrupt-parent = <&gpio3>;
- interrupts = <22 0>;
- wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
- linux,wakeup;
- };
-};
-
-&iomuxc {
- imx6dl-tx6u-811x {
- pinctrl_eeti: eetigrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
- >;
- };
- };
-};
-
-&kpp {
- status = "disabled"; /* pad conflict with backlight1 PWM */
-};
-
-&ldb {
- status = "okay";
-
- lvds0: lvds-channel at 0 {
- fsl,data-mapping = "spwg";
- fsl,data-width = <18>;
- status = "okay";
-
- display-timings {
- native-mode = <&lvds_timing0>;
- lvds_timing0: hsd100pxn1 {
- clock-frequency = <65000000>;
- hactive = <1024>;
- vactive = <768>;
- hback-porch = <220>;
- hfront-porch = <40>;
- vback-porch = <21>;
- vfront-porch = <7>;
- hsync-len = <60>;
- vsync-len = <10>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
-
- lvds1: lvds-channel at 1 {
- fsl,data-mapping = "spwg";
- fsl,data-width = <18>;
- status = "disabled";
-
- display-timings {
- native-mode = <&lvds_timing1>;
- lvds_timing1: hsd100pxn1 {
- clock-frequency = <65000000>;
- hactive = <1024>;
- vactive = <768>;
- hback-porch = <220>;
- hfront-porch = <40>;
- vback-porch = <21>;
- vfront-porch = <7>;
- hsync-len = <60>;
- vsync-len = <10>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
-};
-
-&pwm1 {
- status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-81xx.dts b/arch/arm/boot/dts/imx6dl-tx6u-81xx.dts
new file mode 100644
index 0000000..5ff8e13
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6u-81xx.dts
@@ -0,0 +1,156 @@
+/*
+ * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6U-81xx Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &lvds0;
+ lvds0 = &lvds0;
+ lvds1 = &lvds1;
+ };
+
+ backlight0: backlight0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 0>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ backlight1: backlight1 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000 0>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+};
+
+&i2c3 {
+ polytouch1: eeti at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eeti>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <22 0>;
+ wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ linux,wakeup;
+ };
+};
+
+&iomuxc {
+ imx6dl-tx6u-81xx {
+ pinctrl_eeti: eetigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
+ >;
+ };
+ };
+};
+
+&kpp {
+ status = "disabled"; /* pads partially clash with backlight1 PWM */
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel at 0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds0_timing0>;
+
+ lvds0_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+
+ lvds1: lvds-channel at 1 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "disabled";
+
+ display-timings {
+ native-mode = <&lvds1_timing0>;
+
+ lvds1_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts b/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts
deleted file mode 100644
index b18fae1..0000000
--- a/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts
+++ /dev/null
@@ -1,103 +0,0 @@
-/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-tx6.dtsi"
-
-/ {
- model = "Ka-Ro electronics TX6Q-1010 Module on CoMpact TFT";
- compatible = "karo,imx6q-tx6q", "fsl,imx6q";
-
- aliases {
- display = &display;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm2 0 500000 0>;
- power-supply = <®_3v3>;
- /*
- * a poor man's way to create a 1:1 relationship between
- * the PWM value and the actual duty cycle
- */
- brightness-levels = < 0 1 2 3 4 5 6 7 8 9
- 10 11 12 13 14 15 16 17 18 19
- 20 21 22 23 24 25 26 27 28 29
- 30 31 32 33 34 35 36 37 38 39
- 40 41 42 43 44 45 46 47 48 49
- 50 51 52 53 54 55 56 57 58 59
- 60 61 62 63 64 65 66 67 68 69
- 70 71 72 73 74 75 76 77 78 79
- 80 81 82 83 84 85 86 87 88 89
- 90 91 92 93 94 95 96 97 98 99
- 100>;
- default-brightness-level = <50>;
- };
-
- display: display at di0 {
- compatible = "fsl,imx-parallel-display";
- interface-pix-fmt = "rgb24";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_disp0_1>;
- status = "okay";
-
- port {
- display0_in: endpoint {
- remote-endpoint = <&ipu1_di0_disp0>;
- };
- };
-
- display-timings {
- native-mode = <&ET070001DM6>;
-
- ET070001DM6: CoMTFT { /* same as ET0700 but with inverted pixel clock */
- clock-frequency = <33264000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <88>;
- hsync-len = <128>;
- hfront-porch = <40>;
- vback-porch = <33>;
- vsync-len = <2>;
- vfront-porch = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
-};
-
-&can1 {
- status = "disabled";
-};
-
-&can2 {
- xceiver-supply = <®_3v3>;
-};
-
-&ipu1_di0_disp0 {
- remote-endpoint = <&display0_in>;
-};
-
-&kpp {
- status = "disabled";
-};
-
-®_can_xcvr {
- status = "disabled";
-};
-
-&touchscreen {
- status = "disabled";
-};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1010.dts b/arch/arm/boot/dts/imx6q-tx6q-1010.dts
deleted file mode 100644
index b58ec9c..0000000
--- a/arch/arm/boot/dts/imx6q-tx6q-1010.dts
+++ /dev/null
@@ -1,177 +0,0 @@
-/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-tx6.dtsi"
-
-/ {
- model = "Ka-Ro electronics TX6Q-1010 Module";
- compatible = "karo,imx6q-tx6q", "fsl,imx6q";
-
- aliases {
- display = &display;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
- power-supply = <®_3v3>;
- /*
- * a poor man's way to create a 1:1 relationship between
- * the PWM value and the actual duty cycle
- */
- brightness-levels = < 0 1 2 3 4 5 6 7 8 9
- 10 11 12 13 14 15 16 17 18 19
- 20 21 22 23 24 25 26 27 28 29
- 30 31 32 33 34 35 36 37 38 39
- 40 41 42 43 44 45 46 47 48 49
- 50 51 52 53 54 55 56 57 58 59
- 60 61 62 63 64 65 66 67 68 69
- 70 71 72 73 74 75 76 77 78 79
- 80 81 82 83 84 85 86 87 88 89
- 90 91 92 93 94 95 96 97 98 99
- 100>;
- default-brightness-level = <50>;
- };
-
- display: display at di0 {
- compatible = "fsl,imx-parallel-display";
- interface-pix-fmt = "rgb24";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_disp0_1>;
- status = "okay";
-
- port {
- display0_in: endpoint {
- remote-endpoint = <&ipu1_di0_disp0>;
- };
- };
-
- display-timings {
- VGA {
- clock-frequency = <25200000>;
- hactive = <640>;
- vactive = <480>;
- hback-porch = <48>;
- hsync-len = <96>;
- hfront-porch = <16>;
- vback-porch = <31>;
- vsync-len = <2>;
- vfront-porch = <12>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
-
- ETV570 {
- clock-frequency = <25200000>;
- hactive = <640>;
- vactive = <480>;
- hback-porch = <114>;
- hsync-len = <30>;
- hfront-porch = <16>;
- vback-porch = <32>;
- vsync-len = <3>;
- vfront-porch = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
-
- ET0350 {
- clock-frequency = <6413760>;
- hactive = <320>;
- vactive = <240>;
- hback-porch = <34>;
- hsync-len = <34>;
- hfront-porch = <20>;
- vback-porch = <15>;
- vsync-len = <3>;
- vfront-porch = <4>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
-
- ET0430 {
- clock-frequency = <9009000>;
- hactive = <480>;
- vactive = <272>;
- hback-porch = <2>;
- hsync-len = <41>;
- hfront-porch = <2>;
- vback-porch = <2>;
- vsync-len = <10>;
- vfront-porch = <2>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
-
- ET0500 {
- clock-frequency = <33264000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <88>;
- hsync-len = <128>;
- hfront-porch = <40>;
- vback-porch = <33>;
- vsync-len = <2>;
- vfront-porch = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
-
- ET0700 { /* same as ET0500 */
- clock-frequency = <33264000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <88>;
- hsync-len = <128>;
- hfront-porch = <40>;
- vback-porch = <33>;
- vsync-len = <2>;
- vfront-porch = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
-
- ETQ570 {
- clock-frequency = <6596040>;
- hactive = <320>;
- vactive = <240>;
- hback-porch = <38>;
- hsync-len = <30>;
- hfront-porch = <30>;
- vback-porch = <16>;
- vsync-len = <3>;
- vfront-porch = <4>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
- };
- };
-};
-
-&ipu1_di0_disp0 {
- remote-endpoint = <&display0_in>;
-};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-10x0-comtft.dts b/arch/arm/boot/dts/imx6q-tx6q-10x0-comtft.dts
new file mode 100644
index 0000000..8997553
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-tx6q-10x0-comtft.dts
@@ -0,0 +1,119 @@
+/*
+ * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6Q-1010/-1030 Module on CoMpact TFT";
+ compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+
+ aliases {
+ display = &mxcfb0;
+ mxcfb0 = &mxcfb0;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 0>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ mxcfb0: fb at 2 {
+ compatible = "fsl,mxc_sdc_fb";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_2>;
+ disp_dev = "lcd";
+ interface_pix_fmt = "RGB24";
+ mode_str = "";
+ default_bpp = <32>;
+ int_clk = <1>;
+ late_init = <0>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&ET070001DM6>;
+
+ ET070001DM6: CoMTFT { /* same as ET0700 but with inverted pixel clock */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+
+ lcd: lcd at 0 {
+ compatible = "fsl,lcd";
+ ipu_id = <0>;
+ disp_id = <0>;
+ default_ifmt = "RGB24";
+ status = "okay";
+ };
+};
+
+&can1 {
+ status = "disabled";
+};
+
+&can2 {
+ xceiver-supply = <®_3v3>;
+};
+
+&ipu2 {
+ status = "disabled";
+};
+
+&kpp {
+ status = "disabled";
+};
+
+®_can_xcvr {
+ status = "disabled";
+};
+
+®_lcd0_pwr {
+ status = "okay";
+};
+
+®_lcd1_pwr {
+ status = "okay";
+};
+
+&touchscreen {
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-10x0.dts b/arch/arm/boot/dts/imx6q-tx6q-10x0.dts
new file mode 100644
index 0000000..c3782af
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-tx6q-10x0.dts
@@ -0,0 +1,191 @@
+/*
+ * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6Q-1010/-1030 Module";
+ compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+
+ aliases {
+ display = &display;
+ ipu1 = &ipu1;
+ ipu2 = &ipu2;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ interface-pix-fmt = "rgb24";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_1>;
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+&ipu2 {
+ status = "disabled";
+};
+
+®_lcd0_pwr {
+ status = "okay";
+};
+
+®_lcd1_pwr {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1110.dts b/arch/arm/boot/dts/imx6q-tx6q-1110.dts
deleted file mode 100644
index 88aa1e4..0000000
--- a/arch/arm/boot/dts/imx6q-tx6q-1110.dts
+++ /dev/null
@@ -1,154 +0,0 @@
-/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-tx6.dtsi"
-
-/ {
- model = "Ka-Ro electronics TX6Q-1110 Module";
- compatible = "karo,imx6q-tx6q", "fsl,imx6q";
-
- aliases {
- display = &lvds0;
- lvds0 = &lvds0;
- lvds1 = &lvds1;
- };
-
- backlight0: backlight0 {
- compatible = "pwm-backlight";
- pwms = <&pwm2 0 500000 0>;
- power-supply = <®_lcd0_pwr>;
- /*
- * a poor man's way to create a 1:1 relationship between
- * the PWM value and the actual duty cycle
- */
- brightness-levels = < 0 1 2 3 4 5 6 7 8 9
- 10 11 12 13 14 15 16 17 18 19
- 20 21 22 23 24 25 26 27 28 29
- 30 31 32 33 34 35 36 37 38 39
- 40 41 42 43 44 45 46 47 48 49
- 50 51 52 53 54 55 56 57 58 59
- 60 61 62 63 64 65 66 67 68 69
- 70 71 72 73 74 75 76 77 78 79
- 80 81 82 83 84 85 86 87 88 89
- 90 91 92 93 94 95 96 97 98 99
- 100>;
- default-brightness-level = <50>;
- };
-
- backlight1: backlight1 {
- compatible = "pwm-backlight";
- pwms = <&pwm1 0 500000 0>;
- power-supply = <®_lcd1_pwr>;
- /*
- * a poor man's way to create a 1:1 relationship between
- * the PWM value and the actual duty cycle
- */
- brightness-levels = < 0 1 2 3 4 5 6 7 8 9
- 10 11 12 13 14 15 16 17 18 19
- 20 21 22 23 24 25 26 27 28 29
- 30 31 32 33 34 35 36 37 38 39
- 40 41 42 43 44 45 46 47 48 49
- 50 51 52 53 54 55 56 57 58 59
- 60 61 62 63 64 65 66 67 68 69
- 70 71 72 73 74 75 76 77 78 79
- 80 81 82 83 84 85 86 87 88 89
- 90 91 92 93 94 95 96 97 98 99
- 100>;
- default-brightness-level = <50>;
- };
-};
-
-&i2c3 {
- polytouch1: eeti at 04 {
- compatible = "eeti,egalax_ts";
- reg = <0x04>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_eeti>;
- interrupt-parent = <&gpio3>;
- interrupts = <22 0>;
- wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
- linux,wakeup;
- };
-};
-
-&iomuxc {
- imx6q-tx6q-1110 {
- pinctrl_eeti: eetigrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
- >;
- };
- };
-};
-
-&kpp {
- status = "disabled"; /* pad conflict with backlight1 PWM */
-};
-
-&ldb {
- status = "okay";
-
- lvds0: lvds-channel at 0 {
- fsl,data-mapping = "spwg";
- fsl,data-width = <18>;
- status = "okay";
-
- display-timings {
- native-mode = <&lvds_timing0>;
- lvds_timing0: hsd100pxn1 {
- clock-frequency = <65000000>;
- hactive = <1024>;
- vactive = <768>;
- hback-porch = <220>;
- hfront-porch = <40>;
- vback-porch = <21>;
- vfront-porch = <7>;
- hsync-len = <60>;
- vsync-len = <10>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
-
- lvds1: lvds-channel at 1 {
- fsl,data-mapping = "spwg";
- fsl,data-width = <18>;
- status = "disabled";
-
- display-timings {
- native-mode = <&lvds_timing1>;
- lvds_timing1: hsd100pxn1 {
- clock-frequency = <65000000>;
- hactive = <1024>;
- vactive = <768>;
- hback-porch = <220>;
- hfront-porch = <40>;
- vback-porch = <21>;
- vfront-porch = <7>;
- hsync-len = <60>;
- vsync-len = <10>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
-};
-
-&pwm1 {
- status = "okay";
-};
-
-&sata {
- status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-11x0.dts b/arch/arm/boot/dts/imx6q-tx6q-11x0.dts
new file mode 100644
index 0000000..c66524b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-tx6q-11x0.dts
@@ -0,0 +1,249 @@
+/*
+ * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6Q-1110/-1130 Module";
+ compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+
+ aliases {
+ display = &lvds0;
+ ipu1 = &ipu2;
+ lvds0 = &lvds0;
+ lvds1 = &lvds1;
+ mxcfb0 = &lvds0;
+ mxcfb1 = &lvds1;
+ };
+
+ backlight0: backlight0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 0>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ backlight1: backlight1 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000 0>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ lvds0: fb at 0 {
+ compatible = "fsl,mxc_sdc_fb";
+ disp_dev = "ldb";
+ interface_pix_fmt = "RGB666";
+ mode_str = "LDB-XGA";
+ default_bpp = <32>;
+ int_clk = <0>;
+ late_init = <0>;
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds0_timing0>;
+
+ lvds0_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds0_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds0_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+
+ lvds1: fb at 1 {
+ compatible = "fsl,mxc_sdc_fb";
+ disp_dev = "ldb";
+ interface_pix_fmt = "RGB666";
+ mode_str = "LDB-XGA";
+ default_bpp = <32>;
+ int_clk = <0>;
+ late_init = <0>;
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds1_timing0>;
+
+ lvds1_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds1_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds1_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&i2c3 {
+ polytouch1: eeti at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eeti>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <22 0>;
+ wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ linux,wakeup;
+ };
+};
+
+&iomuxc {
+ imx6q-tx6q-11x0 {
+ pinctrl_eeti: eetigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
+ >;
+ };
+ };
+};
+
+&ipu2 {
+ status = "disabled";
+};
+
+&kpp {
+ status = "disabled"; /* pads partially clash with backlight1 PWM */
+};
+
+&ldb {
+ ipu_id = <0>;
+ disp_id = <0>;
+ ext_ref = <0>;
+ mode = "sep0";
+ sec_ipu_id = <0>;
+ sec_disp_id = <1>;
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 4/6] ARM: dts: imx6: change TX6 module names due to new HW revision
2016-01-20 12:57 ` [PATCH 4/6] ARM: dts: imx6: change TX6 module names due to new HW revision Lothar Waßmann
@ 2016-02-02 6:36 ` Shawn Guo
0 siblings, 0 replies; 13+ messages in thread
From: Shawn Guo @ 2016-02-02 6:36 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Jan 20, 2016 at 01:57:04PM +0100, Lothar Wa?mann wrote:
> The second last digit of the Ka-Ro electronics TX-module names denotes
> the HW revision of the module. HW rev 1 and 3 of the TX6 modules can
> use the same DTB. Change this digit to 'x' to indicate that the DTB
> file can be used for both HW revisions.
This is simply a unnecessary churn of the source tree. I wouldn't take
it.
Shawn
>
> Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
> ---
> arch/arm/boot/dts/Makefile | 10 +-
> arch/arm/boot/dts/imx6dl-tx6u-801x.dts | 177 -------------------
> arch/arm/boot/dts/imx6dl-tx6u-80xx.dts | 185 ++++++++++++++++++++
> arch/arm/boot/dts/imx6dl-tx6u-811x.dts | 150 ----------------
> arch/arm/boot/dts/imx6dl-tx6u-81xx.dts | 156 +++++++++++++++++
> arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts | 103 -----------
> arch/arm/boot/dts/imx6q-tx6q-1010.dts | 177 -------------------
> arch/arm/boot/dts/imx6q-tx6q-10x0-comtft.dts | 119 +++++++++++++
> arch/arm/boot/dts/imx6q-tx6q-10x0.dts | 191 ++++++++++++++++++++
> arch/arm/boot/dts/imx6q-tx6q-1110.dts | 154 -----------------
> arch/arm/boot/dts/imx6q-tx6q-11x0.dts | 249 +++++++++++++++++++++++++++
> 11 files changed, 905 insertions(+), 766 deletions(-)
> delete mode 100644 arch/arm/boot/dts/imx6dl-tx6u-801x.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-80xx.dts
> delete mode 100644 arch/arm/boot/dts/imx6dl-tx6u-811x.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-81xx.dts
> delete mode 100644 arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts
> delete mode 100644 arch/arm/boot/dts/imx6q-tx6q-1010.dts
> create mode 100644 arch/arm/boot/dts/imx6q-tx6q-10x0-comtft.dts
> create mode 100644 arch/arm/boot/dts/imx6q-tx6q-10x0.dts
> delete mode 100644 arch/arm/boot/dts/imx6q-tx6q-1110.dts
> create mode 100644 arch/arm/boot/dts/imx6q-tx6q-11x0.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index a4a6d70..5759aac 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -312,8 +312,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-sabrelite.dtb \
> imx6dl-sabresd.dtb \
> imx6dl-tx6dl-comtft.dtb \
> - imx6dl-tx6u-801x.dtb \
> - imx6dl-tx6u-811x.dtb \
> + imx6dl-tx6u-80xx.dtb \
> + imx6dl-tx6u-81xx.dtb \
> imx6dl-udoo.dtb \
> imx6dl-wandboard.dtb \
> imx6dl-wandboard-revb1.dtb \
> @@ -342,11 +342,11 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-sabresd.dtb \
> imx6q-sbc6x.dtb \
> imx6q-tbs2910.dtb \
> - imx6q-tx6q-1010.dtb \
> - imx6q-tx6q-1010-comtft.dtb \
> imx6q-tx6q-1020.dtb \
> imx6q-tx6q-1020-comtft.dtb \
> - imx6q-tx6q-1110.dtb \
> + imx6q-tx6q-10x0-comtft.dtb \
> + imx6q-tx6q-10x0.dtb \
> + imx6q-tx6q-11x0.dtb \
> imx6q-udoo.dtb \
> imx6q-wandboard.dtb \
> imx6q-wandboard-revb1.dtb
> diff --git a/arch/arm/boot/dts/imx6dl-tx6u-801x.dts b/arch/arm/boot/dts/imx6dl-tx6u-801x.dts
> deleted file mode 100644
> index 5fe465c..0000000
> --- a/arch/arm/boot/dts/imx6dl-tx6u-801x.dts
> +++ /dev/null
> @@ -1,177 +0,0 @@
> -/*
> - * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
> - *
> - * The code contained herein is licensed under the GNU General Public
> - * License. You may obtain a copy of the GNU General Public License
> - * Version 2 at the following locations:
> - *
> - * http://www.opensource.org/licenses/gpl-license.html
> - * http://www.gnu.org/copyleft/gpl.html
> - */
> -
> -/dts-v1/;
> -#include "imx6dl.dtsi"
> -#include "imx6qdl-tx6.dtsi"
> -
> -/ {
> - model = "Ka-Ro electronics TX6U-801x Module";
> - compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> -
> - aliases {
> - display = &display;
> - };
> -
> - backlight: backlight {
> - compatible = "pwm-backlight";
> - pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> - power-supply = <®_3v3>;
> - /*
> - * a poor man's way to create a 1:1 relationship between
> - * the PWM value and the actual duty cycle
> - */
> - brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> - 10 11 12 13 14 15 16 17 18 19
> - 20 21 22 23 24 25 26 27 28 29
> - 30 31 32 33 34 35 36 37 38 39
> - 40 41 42 43 44 45 46 47 48 49
> - 50 51 52 53 54 55 56 57 58 59
> - 60 61 62 63 64 65 66 67 68 69
> - 70 71 72 73 74 75 76 77 78 79
> - 80 81 82 83 84 85 86 87 88 89
> - 90 91 92 93 94 95 96 97 98 99
> - 100>;
> - default-brightness-level = <50>;
> - };
> -
> - display: display at di0 {
> - compatible = "fsl,imx-parallel-display";
> - interface-pix-fmt = "rgb24";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_disp0_1>;
> - status = "okay";
> -
> - port {
> - display0_in: endpoint {
> - remote-endpoint = <&ipu1_di0_disp0>;
> - };
> - };
> -
> - display-timings {
> - VGA {
> - clock-frequency = <25200000>;
> - hactive = <640>;
> - vactive = <480>;
> - hback-porch = <48>;
> - hsync-len = <96>;
> - hfront-porch = <16>;
> - vback-porch = <31>;
> - vsync-len = <2>;
> - vfront-porch = <12>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <0>;
> - };
> -
> - ETV570 {
> - clock-frequency = <25200000>;
> - hactive = <640>;
> - vactive = <480>;
> - hback-porch = <114>;
> - hsync-len = <30>;
> - hfront-porch = <16>;
> - vback-porch = <32>;
> - vsync-len = <3>;
> - vfront-porch = <10>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <0>;
> - };
> -
> - ET0350 {
> - clock-frequency = <6413760>;
> - hactive = <320>;
> - vactive = <240>;
> - hback-porch = <34>;
> - hsync-len = <34>;
> - hfront-porch = <20>;
> - vback-porch = <15>;
> - vsync-len = <3>;
> - vfront-porch = <4>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <0>;
> - };
> -
> - ET0430 {
> - clock-frequency = <9009000>;
> - hactive = <480>;
> - vactive = <272>;
> - hback-porch = <2>;
> - hsync-len = <41>;
> - hfront-porch = <2>;
> - vback-porch = <2>;
> - vsync-len = <10>;
> - vfront-porch = <2>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <1>;
> - };
> -
> - ET0500 {
> - clock-frequency = <33264000>;
> - hactive = <800>;
> - vactive = <480>;
> - hback-porch = <88>;
> - hsync-len = <128>;
> - hfront-porch = <40>;
> - vback-porch = <33>;
> - vsync-len = <2>;
> - vfront-porch = <10>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <0>;
> - };
> -
> - ET0700 { /* same as ET0500 */
> - clock-frequency = <33264000>;
> - hactive = <800>;
> - vactive = <480>;
> - hback-porch = <88>;
> - hsync-len = <128>;
> - hfront-porch = <40>;
> - vback-porch = <33>;
> - vsync-len = <2>;
> - vfront-porch = <10>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <0>;
> - };
> -
> - ETQ570 {
> - clock-frequency = <6596040>;
> - hactive = <320>;
> - vactive = <240>;
> - hback-porch = <38>;
> - hsync-len = <30>;
> - hfront-porch = <30>;
> - vback-porch = <16>;
> - vsync-len = <3>;
> - vfront-porch = <4>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <0>;
> - };
> - };
> - };
> -};
> -
> -&ipu1_di0_disp0 {
> - remote-endpoint = <&display0_in>;
> -};
> diff --git a/arch/arm/boot/dts/imx6dl-tx6u-80xx.dts b/arch/arm/boot/dts/imx6dl-tx6u-80xx.dts
> new file mode 100644
> index 0000000..f6621d6
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-tx6u-80xx.dts
> @@ -0,0 +1,185 @@
> +/*
> + * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6U-801x/-803x Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> +
> + aliases {
> + display = &display;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + power-supply = <®_3v3>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display at di0 {
> + compatible = "fsl,imx-parallel-display";
> + interface-pix-fmt = "rgb24";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_1>;
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +®_lcd0_pwr {
> + status = "okay";
> +};
> +
> +®_lcd1_pwr {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
> deleted file mode 100644
> index c275eec..0000000
> --- a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
> +++ /dev/null
> @@ -1,150 +0,0 @@
> -/*
> - * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
> - *
> - * The code contained herein is licensed under the GNU General Public
> - * License. You may obtain a copy of the GNU General Public License
> - * Version 2 at the following locations:
> - *
> - * http://www.opensource.org/licenses/gpl-license.html
> - * http://www.gnu.org/copyleft/gpl.html
> - */
> -
> -/dts-v1/;
> -#include "imx6dl.dtsi"
> -#include "imx6qdl-tx6.dtsi"
> -
> -/ {
> - model = "Ka-Ro electronics TX6U-811x Module";
> - compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> -
> - aliases {
> - display = &lvds0;
> - lvds0 = &lvds0;
> - lvds1 = &lvds1;
> - };
> -
> - backlight0: backlight0 {
> - compatible = "pwm-backlight";
> - pwms = <&pwm2 0 500000 0>;
> - power-supply = <®_lcd0_pwr>;
> - /*
> - * a poor man's way to create a 1:1 relationship between
> - * the PWM value and the actual duty cycle
> - */
> - brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> - 10 11 12 13 14 15 16 17 18 19
> - 20 21 22 23 24 25 26 27 28 29
> - 30 31 32 33 34 35 36 37 38 39
> - 40 41 42 43 44 45 46 47 48 49
> - 50 51 52 53 54 55 56 57 58 59
> - 60 61 62 63 64 65 66 67 68 69
> - 70 71 72 73 74 75 76 77 78 79
> - 80 81 82 83 84 85 86 87 88 89
> - 90 91 92 93 94 95 96 97 98 99
> - 100>;
> - default-brightness-level = <50>;
> - };
> -
> - backlight1: backlight1 {
> - compatible = "pwm-backlight";
> - pwms = <&pwm1 0 500000 0>;
> - power-supply = <®_lcd1_pwr>;
> - /*
> - * a poor man's way to create a 1:1 relationship between
> - * the PWM value and the actual duty cycle
> - */
> - brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> - 10 11 12 13 14 15 16 17 18 19
> - 20 21 22 23 24 25 26 27 28 29
> - 30 31 32 33 34 35 36 37 38 39
> - 40 41 42 43 44 45 46 47 48 49
> - 50 51 52 53 54 55 56 57 58 59
> - 60 61 62 63 64 65 66 67 68 69
> - 70 71 72 73 74 75 76 77 78 79
> - 80 81 82 83 84 85 86 87 88 89
> - 90 91 92 93 94 95 96 97 98 99
> - 100>;
> - default-brightness-level = <50>;
> - };
> -};
> -
> -&i2c3 {
> - polytouch2: eeti at 04 {
> - compatible = "eeti,egalax_ts";
> - reg = <0x04>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_eeti>;
> - interrupt-parent = <&gpio3>;
> - interrupts = <22 0>;
> - wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> - linux,wakeup;
> - };
> -};
> -
> -&iomuxc {
> - imx6dl-tx6u-811x {
> - pinctrl_eeti: eetigrp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
> - >;
> - };
> - };
> -};
> -
> -&kpp {
> - status = "disabled"; /* pad conflict with backlight1 PWM */
> -};
> -
> -&ldb {
> - status = "okay";
> -
> - lvds0: lvds-channel at 0 {
> - fsl,data-mapping = "spwg";
> - fsl,data-width = <18>;
> - status = "okay";
> -
> - display-timings {
> - native-mode = <&lvds_timing0>;
> - lvds_timing0: hsd100pxn1 {
> - clock-frequency = <65000000>;
> - hactive = <1024>;
> - vactive = <768>;
> - hback-porch = <220>;
> - hfront-porch = <40>;
> - vback-porch = <21>;
> - vfront-porch = <7>;
> - hsync-len = <60>;
> - vsync-len = <10>;
> - de-active = <1>;
> - pixelclk-active = <1>;
> - };
> - };
> - };
> -
> - lvds1: lvds-channel at 1 {
> - fsl,data-mapping = "spwg";
> - fsl,data-width = <18>;
> - status = "disabled";
> -
> - display-timings {
> - native-mode = <&lvds_timing1>;
> - lvds_timing1: hsd100pxn1 {
> - clock-frequency = <65000000>;
> - hactive = <1024>;
> - vactive = <768>;
> - hback-porch = <220>;
> - hfront-porch = <40>;
> - vback-porch = <21>;
> - vfront-porch = <7>;
> - hsync-len = <60>;
> - vsync-len = <10>;
> - de-active = <1>;
> - pixelclk-active = <1>;
> - };
> - };
> - };
> -};
> -
> -&pwm1 {
> - status = "okay";
> -};
> diff --git a/arch/arm/boot/dts/imx6dl-tx6u-81xx.dts b/arch/arm/boot/dts/imx6dl-tx6u-81xx.dts
> new file mode 100644
> index 0000000..5ff8e13
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-tx6u-81xx.dts
> @@ -0,0 +1,156 @@
> +/*
> + * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6U-81xx Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> +
> + aliases {
> + display = &lvds0;
> + lvds0 = &lvds0;
> + lvds1 = &lvds1;
> + };
> +
> + backlight0: backlight0 {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 0>;
> + power-supply = <®_3v3>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + backlight1: backlight1 {
> + compatible = "pwm-backlight";
> + pwms = <&pwm1 0 500000 0>;
> + power-supply = <®_3v3>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +};
> +
> +&i2c3 {
> + polytouch1: eeti at 04 {
> + compatible = "eeti,egalax_ts";
> + reg = <0x04>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_eeti>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <22 0>;
> + wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> + linux,wakeup;
> + };
> +};
> +
> +&iomuxc {
> + imx6dl-tx6u-81xx {
> + pinctrl_eeti: eetigrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
> + >;
> + };
> + };
> +};
> +
> +&kpp {
> + status = "disabled"; /* pads partially clash with backlight1 PWM */
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds0: lvds-channel at 0 {
> + fsl,data-mapping = "spwg";
> + fsl,data-width = <18>;
> + status = "okay";
> +
> + display-timings {
> + native-mode = <&lvds0_timing0>;
> +
> + lvds0_timing0: hsd100pxn1 {
> + clock-frequency = <65000000>;
> + hactive = <1024>;
> + vactive = <768>;
> + hback-porch = <220>;
> + hfront-porch = <40>;
> + vback-porch = <21>;
> + vfront-porch = <7>;
> + hsync-len = <60>;
> + vsync-len = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> + };
> + };
> +
> + lvds1: lvds-channel at 1 {
> + fsl,data-mapping = "spwg";
> + fsl,data-width = <18>;
> + status = "disabled";
> +
> + display-timings {
> + native-mode = <&lvds1_timing0>;
> +
> + lvds1_timing0: hsd100pxn1 {
> + clock-frequency = <65000000>;
> + hactive = <1024>;
> + vactive = <768>;
> + hback-porch = <220>;
> + hfront-porch = <40>;
> + vback-porch = <21>;
> + vfront-porch = <7>;
> + hsync-len = <60>;
> + vsync-len = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> + };
> + };
> +};
> +
> +&pwm1 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts b/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts
> deleted file mode 100644
> index b18fae1..0000000
> --- a/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts
> +++ /dev/null
> @@ -1,103 +0,0 @@
> -/*
> - * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
> - *
> - * The code contained herein is licensed under the GNU General Public
> - * License. You may obtain a copy of the GNU General Public License
> - * Version 2 at the following locations:
> - *
> - * http://www.opensource.org/licenses/gpl-license.html
> - * http://www.gnu.org/copyleft/gpl.html
> - */
> -
> -/dts-v1/;
> -#include "imx6q.dtsi"
> -#include "imx6qdl-tx6.dtsi"
> -
> -/ {
> - model = "Ka-Ro electronics TX6Q-1010 Module on CoMpact TFT";
> - compatible = "karo,imx6q-tx6q", "fsl,imx6q";
> -
> - aliases {
> - display = &display;
> - };
> -
> - backlight: backlight {
> - compatible = "pwm-backlight";
> - pwms = <&pwm2 0 500000 0>;
> - power-supply = <®_3v3>;
> - /*
> - * a poor man's way to create a 1:1 relationship between
> - * the PWM value and the actual duty cycle
> - */
> - brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> - 10 11 12 13 14 15 16 17 18 19
> - 20 21 22 23 24 25 26 27 28 29
> - 30 31 32 33 34 35 36 37 38 39
> - 40 41 42 43 44 45 46 47 48 49
> - 50 51 52 53 54 55 56 57 58 59
> - 60 61 62 63 64 65 66 67 68 69
> - 70 71 72 73 74 75 76 77 78 79
> - 80 81 82 83 84 85 86 87 88 89
> - 90 91 92 93 94 95 96 97 98 99
> - 100>;
> - default-brightness-level = <50>;
> - };
> -
> - display: display at di0 {
> - compatible = "fsl,imx-parallel-display";
> - interface-pix-fmt = "rgb24";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_disp0_1>;
> - status = "okay";
> -
> - port {
> - display0_in: endpoint {
> - remote-endpoint = <&ipu1_di0_disp0>;
> - };
> - };
> -
> - display-timings {
> - native-mode = <&ET070001DM6>;
> -
> - ET070001DM6: CoMTFT { /* same as ET0700 but with inverted pixel clock */
> - clock-frequency = <33264000>;
> - hactive = <800>;
> - vactive = <480>;
> - hback-porch = <88>;
> - hsync-len = <128>;
> - hfront-porch = <40>;
> - vback-porch = <33>;
> - vsync-len = <2>;
> - vfront-porch = <10>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <1>;
> - };
> - };
> - };
> -};
> -
> -&can1 {
> - status = "disabled";
> -};
> -
> -&can2 {
> - xceiver-supply = <®_3v3>;
> -};
> -
> -&ipu1_di0_disp0 {
> - remote-endpoint = <&display0_in>;
> -};
> -
> -&kpp {
> - status = "disabled";
> -};
> -
> -®_can_xcvr {
> - status = "disabled";
> -};
> -
> -&touchscreen {
> - status = "disabled";
> -};
> diff --git a/arch/arm/boot/dts/imx6q-tx6q-1010.dts b/arch/arm/boot/dts/imx6q-tx6q-1010.dts
> deleted file mode 100644
> index b58ec9c..0000000
> --- a/arch/arm/boot/dts/imx6q-tx6q-1010.dts
> +++ /dev/null
> @@ -1,177 +0,0 @@
> -/*
> - * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
> - *
> - * The code contained herein is licensed under the GNU General Public
> - * License. You may obtain a copy of the GNU General Public License
> - * Version 2 at the following locations:
> - *
> - * http://www.opensource.org/licenses/gpl-license.html
> - * http://www.gnu.org/copyleft/gpl.html
> - */
> -
> -/dts-v1/;
> -#include "imx6q.dtsi"
> -#include "imx6qdl-tx6.dtsi"
> -
> -/ {
> - model = "Ka-Ro electronics TX6Q-1010 Module";
> - compatible = "karo,imx6q-tx6q", "fsl,imx6q";
> -
> - aliases {
> - display = &display;
> - };
> -
> - backlight: backlight {
> - compatible = "pwm-backlight";
> - pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> - power-supply = <®_3v3>;
> - /*
> - * a poor man's way to create a 1:1 relationship between
> - * the PWM value and the actual duty cycle
> - */
> - brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> - 10 11 12 13 14 15 16 17 18 19
> - 20 21 22 23 24 25 26 27 28 29
> - 30 31 32 33 34 35 36 37 38 39
> - 40 41 42 43 44 45 46 47 48 49
> - 50 51 52 53 54 55 56 57 58 59
> - 60 61 62 63 64 65 66 67 68 69
> - 70 71 72 73 74 75 76 77 78 79
> - 80 81 82 83 84 85 86 87 88 89
> - 90 91 92 93 94 95 96 97 98 99
> - 100>;
> - default-brightness-level = <50>;
> - };
> -
> - display: display at di0 {
> - compatible = "fsl,imx-parallel-display";
> - interface-pix-fmt = "rgb24";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_disp0_1>;
> - status = "okay";
> -
> - port {
> - display0_in: endpoint {
> - remote-endpoint = <&ipu1_di0_disp0>;
> - };
> - };
> -
> - display-timings {
> - VGA {
> - clock-frequency = <25200000>;
> - hactive = <640>;
> - vactive = <480>;
> - hback-porch = <48>;
> - hsync-len = <96>;
> - hfront-porch = <16>;
> - vback-porch = <31>;
> - vsync-len = <2>;
> - vfront-porch = <12>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <0>;
> - };
> -
> - ETV570 {
> - clock-frequency = <25200000>;
> - hactive = <640>;
> - vactive = <480>;
> - hback-porch = <114>;
> - hsync-len = <30>;
> - hfront-porch = <16>;
> - vback-porch = <32>;
> - vsync-len = <3>;
> - vfront-porch = <10>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <0>;
> - };
> -
> - ET0350 {
> - clock-frequency = <6413760>;
> - hactive = <320>;
> - vactive = <240>;
> - hback-porch = <34>;
> - hsync-len = <34>;
> - hfront-porch = <20>;
> - vback-porch = <15>;
> - vsync-len = <3>;
> - vfront-porch = <4>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <0>;
> - };
> -
> - ET0430 {
> - clock-frequency = <9009000>;
> - hactive = <480>;
> - vactive = <272>;
> - hback-porch = <2>;
> - hsync-len = <41>;
> - hfront-porch = <2>;
> - vback-porch = <2>;
> - vsync-len = <10>;
> - vfront-porch = <2>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <1>;
> - };
> -
> - ET0500 {
> - clock-frequency = <33264000>;
> - hactive = <800>;
> - vactive = <480>;
> - hback-porch = <88>;
> - hsync-len = <128>;
> - hfront-porch = <40>;
> - vback-porch = <33>;
> - vsync-len = <2>;
> - vfront-porch = <10>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <0>;
> - };
> -
> - ET0700 { /* same as ET0500 */
> - clock-frequency = <33264000>;
> - hactive = <800>;
> - vactive = <480>;
> - hback-porch = <88>;
> - hsync-len = <128>;
> - hfront-porch = <40>;
> - vback-porch = <33>;
> - vsync-len = <2>;
> - vfront-porch = <10>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <0>;
> - };
> -
> - ETQ570 {
> - clock-frequency = <6596040>;
> - hactive = <320>;
> - vactive = <240>;
> - hback-porch = <38>;
> - hsync-len = <30>;
> - hfront-porch = <30>;
> - vback-porch = <16>;
> - vsync-len = <3>;
> - vfront-porch = <4>;
> - hsync-active = <0>;
> - vsync-active = <0>;
> - de-active = <1>;
> - pixelclk-active = <0>;
> - };
> - };
> - };
> -};
> -
> -&ipu1_di0_disp0 {
> - remote-endpoint = <&display0_in>;
> -};
> diff --git a/arch/arm/boot/dts/imx6q-tx6q-10x0-comtft.dts b/arch/arm/boot/dts/imx6q-tx6q-10x0-comtft.dts
> new file mode 100644
> index 0000000..8997553
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-tx6q-10x0-comtft.dts
> @@ -0,0 +1,119 @@
> +/*
> + * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6Q-1010/-1030 Module on CoMpact TFT";
> + compatible = "karo,imx6q-tx6q", "fsl,imx6q";
> +
> + aliases {
> + display = &mxcfb0;
> + mxcfb0 = &mxcfb0;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 0>;
> + power-supply = <®_3v3>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + mxcfb0: fb at 2 {
> + compatible = "fsl,mxc_sdc_fb";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + disp_dev = "lcd";
> + interface_pix_fmt = "RGB24";
> + mode_str = "";
> + default_bpp = <32>;
> + int_clk = <1>;
> + late_init = <0>;
> + status = "okay";
> +
> + display-timings {
> + native-mode = <&ET070001DM6>;
> +
> + ET070001DM6: CoMTFT { /* same as ET0700 but with inverted pixel clock */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> + };
> + };
> +
> + lcd: lcd at 0 {
> + compatible = "fsl,lcd";
> + ipu_id = <0>;
> + disp_id = <0>;
> + default_ifmt = "RGB24";
> + status = "okay";
> + };
> +};
> +
> +&can1 {
> + status = "disabled";
> +};
> +
> +&can2 {
> + xceiver-supply = <®_3v3>;
> +};
> +
> +&ipu2 {
> + status = "disabled";
> +};
> +
> +&kpp {
> + status = "disabled";
> +};
> +
> +®_can_xcvr {
> + status = "disabled";
> +};
> +
> +®_lcd0_pwr {
> + status = "okay";
> +};
> +
> +®_lcd1_pwr {
> + status = "okay";
> +};
> +
> +&touchscreen {
> + status = "disabled";
> +};
> diff --git a/arch/arm/boot/dts/imx6q-tx6q-10x0.dts b/arch/arm/boot/dts/imx6q-tx6q-10x0.dts
> new file mode 100644
> index 0000000..c3782af
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-tx6q-10x0.dts
> @@ -0,0 +1,191 @@
> +/*
> + * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6Q-1010/-1030 Module";
> + compatible = "karo,imx6q-tx6q", "fsl,imx6q";
> +
> + aliases {
> + display = &display;
> + ipu1 = &ipu1;
> + ipu2 = &ipu2;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + power-supply = <®_3v3>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display at di0 {
> + compatible = "fsl,imx-parallel-display";
> + interface-pix-fmt = "rgb24";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_1>;
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +&ipu2 {
> + status = "disabled";
> +};
> +
> +®_lcd0_pwr {
> + status = "okay";
> +};
> +
> +®_lcd1_pwr {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6q-tx6q-1110.dts b/arch/arm/boot/dts/imx6q-tx6q-1110.dts
> deleted file mode 100644
> index 88aa1e4..0000000
> --- a/arch/arm/boot/dts/imx6q-tx6q-1110.dts
> +++ /dev/null
> @@ -1,154 +0,0 @@
> -/*
> - * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
> - *
> - * The code contained herein is licensed under the GNU General Public
> - * License. You may obtain a copy of the GNU General Public License
> - * Version 2 at the following locations:
> - *
> - * http://www.opensource.org/licenses/gpl-license.html
> - * http://www.gnu.org/copyleft/gpl.html
> - */
> -
> -/dts-v1/;
> -#include "imx6q.dtsi"
> -#include "imx6qdl-tx6.dtsi"
> -
> -/ {
> - model = "Ka-Ro electronics TX6Q-1110 Module";
> - compatible = "karo,imx6q-tx6q", "fsl,imx6q";
> -
> - aliases {
> - display = &lvds0;
> - lvds0 = &lvds0;
> - lvds1 = &lvds1;
> - };
> -
> - backlight0: backlight0 {
> - compatible = "pwm-backlight";
> - pwms = <&pwm2 0 500000 0>;
> - power-supply = <®_lcd0_pwr>;
> - /*
> - * a poor man's way to create a 1:1 relationship between
> - * the PWM value and the actual duty cycle
> - */
> - brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> - 10 11 12 13 14 15 16 17 18 19
> - 20 21 22 23 24 25 26 27 28 29
> - 30 31 32 33 34 35 36 37 38 39
> - 40 41 42 43 44 45 46 47 48 49
> - 50 51 52 53 54 55 56 57 58 59
> - 60 61 62 63 64 65 66 67 68 69
> - 70 71 72 73 74 75 76 77 78 79
> - 80 81 82 83 84 85 86 87 88 89
> - 90 91 92 93 94 95 96 97 98 99
> - 100>;
> - default-brightness-level = <50>;
> - };
> -
> - backlight1: backlight1 {
> - compatible = "pwm-backlight";
> - pwms = <&pwm1 0 500000 0>;
> - power-supply = <®_lcd1_pwr>;
> - /*
> - * a poor man's way to create a 1:1 relationship between
> - * the PWM value and the actual duty cycle
> - */
> - brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> - 10 11 12 13 14 15 16 17 18 19
> - 20 21 22 23 24 25 26 27 28 29
> - 30 31 32 33 34 35 36 37 38 39
> - 40 41 42 43 44 45 46 47 48 49
> - 50 51 52 53 54 55 56 57 58 59
> - 60 61 62 63 64 65 66 67 68 69
> - 70 71 72 73 74 75 76 77 78 79
> - 80 81 82 83 84 85 86 87 88 89
> - 90 91 92 93 94 95 96 97 98 99
> - 100>;
> - default-brightness-level = <50>;
> - };
> -};
> -
> -&i2c3 {
> - polytouch1: eeti at 04 {
> - compatible = "eeti,egalax_ts";
> - reg = <0x04>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_eeti>;
> - interrupt-parent = <&gpio3>;
> - interrupts = <22 0>;
> - wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> - linux,wakeup;
> - };
> -};
> -
> -&iomuxc {
> - imx6q-tx6q-1110 {
> - pinctrl_eeti: eetigrp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
> - >;
> - };
> - };
> -};
> -
> -&kpp {
> - status = "disabled"; /* pad conflict with backlight1 PWM */
> -};
> -
> -&ldb {
> - status = "okay";
> -
> - lvds0: lvds-channel at 0 {
> - fsl,data-mapping = "spwg";
> - fsl,data-width = <18>;
> - status = "okay";
> -
> - display-timings {
> - native-mode = <&lvds_timing0>;
> - lvds_timing0: hsd100pxn1 {
> - clock-frequency = <65000000>;
> - hactive = <1024>;
> - vactive = <768>;
> - hback-porch = <220>;
> - hfront-porch = <40>;
> - vback-porch = <21>;
> - vfront-porch = <7>;
> - hsync-len = <60>;
> - vsync-len = <10>;
> - de-active = <1>;
> - pixelclk-active = <1>;
> - };
> - };
> - };
> -
> - lvds1: lvds-channel at 1 {
> - fsl,data-mapping = "spwg";
> - fsl,data-width = <18>;
> - status = "disabled";
> -
> - display-timings {
> - native-mode = <&lvds_timing1>;
> - lvds_timing1: hsd100pxn1 {
> - clock-frequency = <65000000>;
> - hactive = <1024>;
> - vactive = <768>;
> - hback-porch = <220>;
> - hfront-porch = <40>;
> - vback-porch = <21>;
> - vfront-porch = <7>;
> - hsync-len = <60>;
> - vsync-len = <10>;
> - de-active = <1>;
> - pixelclk-active = <1>;
> - };
> - };
> - };
> -};
> -
> -&pwm1 {
> - status = "okay";
> -};
> -
> -&sata {
> - status = "okay";
> -};
> diff --git a/arch/arm/boot/dts/imx6q-tx6q-11x0.dts b/arch/arm/boot/dts/imx6q-tx6q-11x0.dts
> new file mode 100644
> index 0000000..c66524b
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-tx6q-11x0.dts
> @@ -0,0 +1,249 @@
> +/*
> + * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6Q-1110/-1130 Module";
> + compatible = "karo,imx6q-tx6q", "fsl,imx6q";
> +
> + aliases {
> + display = &lvds0;
> + ipu1 = &ipu2;
> + lvds0 = &lvds0;
> + lvds1 = &lvds1;
> + mxcfb0 = &lvds0;
> + mxcfb1 = &lvds1;
> + };
> +
> + backlight0: backlight0 {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 0>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + backlight1: backlight1 {
> + compatible = "pwm-backlight";
> + pwms = <&pwm1 0 500000 0>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + lvds0: fb at 0 {
> + compatible = "fsl,mxc_sdc_fb";
> + disp_dev = "ldb";
> + interface_pix_fmt = "RGB666";
> + mode_str = "LDB-XGA";
> + default_bpp = <32>;
> + int_clk = <0>;
> + late_init = <0>;
> + fsl,data-mapping = "spwg";
> + fsl,data-width = <18>;
> + status = "okay";
> +
> + display-timings {
> + native-mode = <&lvds0_timing0>;
> +
> + lvds0_timing0: hsd100pxn1 {
> + clock-frequency = <65000000>;
> + hactive = <1024>;
> + vactive = <768>;
> + hback-porch = <220>;
> + hfront-porch = <40>;
> + vback-porch = <21>;
> + vfront-porch = <7>;
> + hsync-len = <60>;
> + vsync-len = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + lvds0_timing1: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vfront-porch = <12>;
> + hsync-len = <96>;
> + vsync-len = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + lvds0_timing2: nl12880bc20 {
> + clock-frequency = <71000000>;
> + hactive = <1280>;
> + vactive = <800>;
> + hback-porch = <50>;
> + hfront-porch = <50>;
> + vback-porch = <5>;
> + vfront-porch = <5>;
> + hsync-len = <60>;
> + vsync-len = <13>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +
> + lvds1: fb at 1 {
> + compatible = "fsl,mxc_sdc_fb";
> + disp_dev = "ldb";
> + interface_pix_fmt = "RGB666";
> + mode_str = "LDB-XGA";
> + default_bpp = <32>;
> + int_clk = <0>;
> + late_init = <0>;
> + fsl,data-mapping = "spwg";
> + fsl,data-width = <18>;
> + status = "okay";
> +
> + display-timings {
> + native-mode = <&lvds1_timing0>;
> +
> + lvds1_timing0: hsd100pxn1 {
> + clock-frequency = <65000000>;
> + hactive = <1024>;
> + vactive = <768>;
> + hback-porch = <220>;
> + hfront-porch = <40>;
> + vback-porch = <21>;
> + vfront-porch = <7>;
> + hsync-len = <60>;
> + vsync-len = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + lvds1_timing1: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vfront-porch = <12>;
> + hsync-len = <96>;
> + vsync-len = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + lvds1_timing2: nl12880bc20 {
> + clock-frequency = <71000000>;
> + hactive = <1280>;
> + vactive = <800>;
> + hback-porch = <50>;
> + hfront-porch = <50>;
> + vback-porch = <5>;
> + vfront-porch = <5>;
> + hsync-len = <60>;
> + vsync-len = <13>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&i2c3 {
> + polytouch1: eeti at 04 {
> + compatible = "eeti,egalax_ts";
> + reg = <0x04>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_eeti>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <22 0>;
> + wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> + linux,wakeup;
> + };
> +};
> +
> +&iomuxc {
> + imx6q-tx6q-11x0 {
> + pinctrl_eeti: eetigrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
> + >;
> + };
> + };
> +};
> +
> +&ipu2 {
> + status = "disabled";
> +};
> +
> +&kpp {
> + status = "disabled"; /* pads partially clash with backlight1 PWM */
> +};
> +
> +&ldb {
> + ipu_id = <0>;
> + disp_id = <0>;
> + ext_ref = <0>;
> + mode = "sep0";
> + sec_ipu_id = <0>;
> + sec_disp_id = <1>;
> + status = "okay";
> +};
> +
> +&pwm1 {
> + status = "okay";
> +};
> +
> +&sata {
> + status = "okay";
> +};
> --
> 2.1.4
>
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 5/6] ARM: dts: imx6: add support for more Ka-Ro electronics modules
2016-01-20 12:57 [PATCH 0/6] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
` (3 preceding siblings ...)
2016-01-20 12:57 ` [PATCH 4/6] ARM: dts: imx6: change TX6 module names due to new HW revision Lothar Waßmann
@ 2016-01-20 12:57 ` Lothar Waßmann
2016-01-20 12:57 ` [PATCH 6/6] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard Lothar Waßmann
5 siblings, 0 replies; 13+ messages in thread
From: Lothar Waßmann @ 2016-01-20 12:57 UTC (permalink / raw)
To: linux-arm-kernel
Add support for the following i.MX6 based modules from Ka-Ro
electronics GmbH:
TX6S-8034:
Processor Freescale i.MX 6 Solo, 800MHz
RAM 256MiB DDR3 SDRAM
ROM 128MiB NAND Flash
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
TX6S-8035:
Processor Freescale i.MX 6 Solo, 800MHz
RAM 512MiB DDR3 SDRAM
ROM 4GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
TX6U-8033:
Processor Freescale i.MX 6 Dual Lite, 800MHz
RAM 1GiB DDR3 SDRAM
ROM 4GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
TX6Q-1036:
Processor Freescale i.MX 6Quad, 1GHz
RAM 1GB DDR3 SDRAM 64-bit
ROM 8GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range Extended Consumer Grade (-20?C to 105?C Tj)
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 4 +
arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 245 +++++++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6dl-tx6s-8035.dts | 216 +++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6dl-tx6u-8033.dts | 227 ++++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6q-tx6q-1036.dts | 227 ++++++++++++++++++++++++++++++
5 files changed, 919 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts
create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8035.dts
create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-8033.dts
create mode 100644 arch/arm/boot/dts/imx6q-tx6q-1036.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 5759aac..e997d6c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -312,6 +312,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \
imx6dl-tx6dl-comtft.dtb \
+ imx6dl-tx6s-8034.dtb \
+ imx6dl-tx6s-8035.dtb \
+ imx6dl-tx6u-8033.dtb \
imx6dl-tx6u-80xx.dtb \
imx6dl-tx6u-81xx.dtb \
imx6dl-udoo.dtb \
@@ -344,6 +347,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-tbs2910.dtb \
imx6q-tx6q-1020.dtb \
imx6q-tx6q-1020-comtft.dtb \
+ imx6q-tx6q-1036.dtb \
imx6q-tx6q-10x0-comtft.dtb \
imx6q-tx6q-10x0.dtb \
imx6q-tx6q-11x0.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
new file mode 100644
index 0000000..4cc28ba
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
@@ -0,0 +1,245 @@
+/*
+ * Copyright 2015 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6S-8034 Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &display;
+ ipu1 = &ipu1;
+ };
+
+ cpus {
+ /delete-node/ cpu at 1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_1>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&pinctrl_hog {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */
+ MX6QDL_PAD_SD3_DAT2__GPIO7_IO06 0x1b0b1 /* ETN PHY RESET */
+ MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b1 /* ETN PHY INT */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b1 /* PWR BTN */
+ >;
+};
+
+&pinctrl_usdhc1 {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x07099
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1
+ MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */
+ >;
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+®_lcd0_pwr {
+ status = "disabled";
+};
+
+®_lcd1_pwr {
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8035.dts b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
new file mode 100644
index 0000000..ca76b8b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
@@ -0,0 +1,216 @@
+/*
+ * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6S-8035 Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &display;
+ ipu1 = &ipu1;
+ };
+
+ cpus {
+ /delete-node/ cpu at 1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ interface-pix-fmt = "rgb24";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_1>;
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&iomuxc {
+ imx6qdl-tx6 {
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
+ MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
+ >;
+ };
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <4>;
+ non-removable;
+ no-1-8-v;
+ fsl,wp-controller;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-8033.dts b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
new file mode 100644
index 0000000..09d9274
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
@@ -0,0 +1,227 @@
+/*
+ * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6U-8033 Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &display;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ interface-pix-fmt = "rgb24";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_1>;
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+
+ lcd: lcd at 0 {
+ compatible = "fsl,lcd";
+ ipu_id = <0>;
+ disp_id = <0>;
+ default_ifmt = "RGB24";
+ status = "okay";
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&iomuxc {
+ imx6qdl-tx6 {
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
+ MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
+ >;
+ };
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+®_lcd0_pwr {
+ status = "okay";
+};
+
+®_lcd1_pwr {
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <4>;
+ non-removable;
+ no-1-8-v;
+ fsl,wp-controller;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1036.dts b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
new file mode 100644
index 0000000..d9a5c35
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
@@ -0,0 +1,227 @@
+/*
+ * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6Q-1033 Module";
+ compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+
+ aliases {
+ display = &mxcfb0;
+ mxcfb0 = &mxcfb0;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ mxcfb0: fb at 2 {
+ compatible = "fsl,mxc_sdc_fb";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_2>;
+ disp_dev = "lcd";
+ interface_pix_fmt = "RGB24";
+ mode_str = "";
+ default_bpp = <32>;
+ int_clk = <1>;
+ late_init = <0>;
+ status = "okay";
+
+ display-timings {
+ VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+
+ lcd: lcd at 0 {
+ compatible = "fsl,lcd";
+ ipu_id = <0>;
+ disp_id = <0>;
+ default_ifmt = "RGB24";
+ status = "okay";
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&iomuxc {
+ imx6qdl-tx6 {
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
+ MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
+ >;
+ };
+ };
+};
+
+&ipu2 {
+ status = "disabled";
+};
+
+®_lcd0_pwr {
+ status = "okay";
+};
+
+®_lcd1_pwr {
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <4>;
+ non-removable;
+ no-1-8-v;
+ fsl,wp-controller;
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 6/6] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard
2016-01-20 12:57 [PATCH 0/6] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
` (4 preceding siblings ...)
2016-01-20 12:57 ` [PATCH 5/6] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
@ 2016-01-20 12:57 ` Lothar Waßmann
5 siblings, 0 replies; 13+ messages in thread
From: Lothar Waßmann @ 2016-01-20 12:57 UTC (permalink / raw)
To: linux-arm-kernel
This baseboard can be used with all TX6 SoMs, but only a certain set
of combinations can be ordered. Add support for these combinations in
mainline, so that users can easily adopt their own combination of SoM
and baseboard themselves.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts | 236 +++++++++++++++++++++++++
arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts | 267 +++++++++++++++++++++++++++++
3 files changed, 505 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts
create mode 100644 arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e997d6c..d520c6d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -316,6 +316,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-tx6s-8035.dtb \
imx6dl-tx6u-8033.dtb \
imx6dl-tx6u-80xx.dtb \
+ imx6dl-tx6u-81xx-mb7.dtb \
imx6dl-tx6u-81xx.dtb \
imx6dl-udoo.dtb \
imx6dl-wandboard.dtb \
@@ -350,6 +351,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-tx6q-1036.dtb \
imx6q-tx6q-10x0-comtft.dtb \
imx6q-tx6q-10x0.dtb \
+ imx6q-tx6q-11x0-mb7.dtb \
imx6q-tx6q-11x0.dtb \
imx6q-udoo.dtb \
imx6q-wandboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts b/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts
new file mode 100644
index 0000000..70552f6
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts
@@ -0,0 +1,236 @@
+/*
+ * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6U-81xx Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &lvds0;
+ lvds0 = &lvds0;
+ lvds1 = &lvds1;
+ };
+
+ backlight0: backlight0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ backlight1: backlight1 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_3v3>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+};
+
+&can1 {
+ status = "disabled";
+};
+
+&can2 {
+ xceiver-supply = <®_3v3>;
+};
+
+&i2c3 {
+ polytouch1: eeti at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eeti>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <22 0>;
+ wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ linux,wakeup;
+ };
+};
+
+&iomuxc {
+ imx6dl-tx6u-81xx {
+ pinctrl_eeti: eetigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
+ >;
+ };
+ };
+};
+
+&kpp {
+ status = "disabled"; /* pads partially clash with backlight1 PWM */
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel at 0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds0_timing1>;
+
+ lvds0_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds0_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds0_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+
+ lvds1: lvds-channel at 1 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "disabled";
+
+ display-timings {
+ native-mode = <&lvds1_timing2>;
+
+ lvds1_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds1_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds1_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+®_lcd0_pwr {
+ status = "okay";
+};
+
+®_lcd1_pwr {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts b/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts
new file mode 100644
index 0000000..d4c6a0e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts
@@ -0,0 +1,267 @@
+/*
+ * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6Q-1110/-1130 Module";
+ compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+
+ aliases {
+ display = &lvds0;
+ ipu1 = &ipu2;
+ lvds0 = &lvds0;
+ lvds1 = &lvds1;
+ mxcfb0 = &lvds0;
+ mxcfb1 = &lvds1;
+ };
+
+ backlight0: backlight0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_lcd0_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ backlight1: backlight1 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ lvds0: fb at 0 {
+ compatible = "fsl,mxc_sdc_fb";
+ disp_dev = "ldb";
+ interface_pix_fmt = "RGB666";
+ mode_str = "LDB-VGA";
+ default_bpp = <32>;
+ int_clk = <0>;
+ late_init = <0>;
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds0_timing1>;
+
+ lvds0_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds0_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds0_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+
+ lvds1: fb at 1 {
+ compatible = "fsl,mxc_sdc_fb";
+ disp_dev = "ldb";
+ interface_pix_fmt = "RGB24";
+ mode_str = "LDB-NL12880BC20";
+ default_bpp = <32>;
+ int_clk = <0>;
+ late_init = <0>;
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds1_timing2>;
+
+ lvds1_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds1_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds1_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&can1 {
+ status = "disabled";
+};
+
+&can2 {
+ xceiver-supply = <®_3v3>;
+};
+
+&i2c3 {
+ polytouch1: eeti at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eeti>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <22 0>;
+ wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ linux,wakeup;
+ };
+};
+
+&iomuxc {
+ imx6q-tx6q-11x0 {
+ pinctrl_eeti: eetigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
+ >;
+ };
+ };
+};
+
+&ipu2 {
+ status = "disabled";
+};
+
+&kpp {
+ status = "disabled"; /* pads partially clash with backlight1 PWM */
+};
+
+&ldb {
+ ipu_id = <0>;
+ disp_id = <0>;
+ ext_ref = <0>;
+ mode = "sep0";
+ sec_ipu_id = <0>;
+ sec_disp_id = <1>;
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+®_lcd0_pwr {
+ status = "okay";
+};
+
+®_lcd1_pwr {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread