* [PATCH v2] ARM: dts: Add dts for Uniwest evi [not found] <patches/evidts/35215> @ 2016-02-02 22:13 ` Joshua Clayton 2016-02-03 9:24 ` Philipp Zabel 0 siblings, 1 reply; 4+ messages in thread From: Joshua Clayton @ 2016-02-02 22:13 UTC (permalink / raw) To: linux-arm-kernel Uniwest evi is a portable electrical eddy current non-destructive testing device. Signed-off-by: Joshua Clayton <stillcompiling@gmail.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6q-evi.dts | 506 ++++++++++++++++++++++++++++++++++++++++ 2 files changed, 507 insertions(+) create mode 100644 arch/arm/boot/dts/imx6q-evi.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index c4f42a78..4a4ef29 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -326,6 +326,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-cubox-i.dtb \ imx6q-dfi-fs700-m60.dtb \ imx6q-dmo-edmqmx6.dtb \ + imx6q-evi.dtb \ imx6q-gk802.dtb \ imx6q-gw51xx.dtb \ imx6q-gw52xx.dtb \ diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts new file mode 100644 index 0000000..10f566e --- /dev/null +++ b/arch/arm/boot/dts/imx6q-evi.dts @@ -0,0 +1,506 @@ +/* + * Copyright 2016 United Western Technologies. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + model = "Uniwest Evi"; + compatible = "uniwest,imx6q-evi", "fsl,imx6q"; + + memory { + reg = <0x10000000 0x40000000>; + }; + + reg_usbh1_vbus: regulator-usbhubreset { + compatible = "regulator-fixed"; + regulator-name = "usbh1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + startup-delay-us = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1_hubreset>; + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>; + }; + + reg_usb_otg_vbus: regulator-usbotgvbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotgvbus>; + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + panel { + compatible = "sharp,lq101k1ly04"; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; +}; + +&ecspi1 { + fsl,spi-num-chipselects = <1>; + cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1cs>; + status = "okay"; +}; + +&ecspi3 { + fsl,spi-num-chipselects = <3>; + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>, + <&gpio4 25 GPIO_ACTIVE_LOW>, + <&gpio4 26 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3cs>; + status = "okay"; +}; + +&ecspi5 { + fsl,spi-num-chipselects = <4>; + cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>, + <&gpio1 13 GPIO_ACTIVE_LOW>, + <&gpio1 12 GPIO_ACTIVE_LOW>, + <&gpio2 9 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5cs>; + status = "okay"; + + eeprom: m95m02 at 1 { + compatible = "st,m95m02", "atmel,at25"; + size = <262144>; + pagesize = <256>; + address-width = <24>; + spi-max-frequency = <5000000>; + reg = <1>; + }; + + pb_rtc: rtc at 3 { + compatible = "nxp,rtc-pcf2123"; + spi-max-frequency = <2450000>; + spi-cs-high; + reg = <3>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 25 0>; + status = "okay"; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpminand>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clock-frequency = <100000>; + status = "okay"; +}; + +&i2c3 { + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c3>; + pinctrl-1 = <&pinctrl_i2c3_gpio>; + clock-frequency = <100000>; + scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>; + status = "okay"; + + battery: sbs-battery at b { + compatible = "sbs,sbs-battery"; + reg = <0x0b>; + sbs,poll-retry-count = <100>; + sbs,i2c-retry-count = <100>; + }; +}; + +&ldb { + status = "okay"; + + lvds0: lvds-channel at 0 { + fsl,data-mapping = "jeida"; + fsl,data-width = <24>; + status = "okay"; + + port at 4 { + reg = <4>; + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + +&ssi1 { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usbh1_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1>; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + dr_mode = "otg"; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + non-removable; + status = "okay"; +}; + +&weim { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x08000000>; + fsl,weim-cs-gpr = <&gpr>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_weimfpga &pinctrl_weimcs>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + /* CPLD Reset */ + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 + /* pwr mcu alert irq */ + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 + /* remainder ???? */ + MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1 + >; + }; + + pinctrl_ecspi1cs: ecspi1csgrp { + fsl,pins = < + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0 + >; + }; + + pinctrl_ecspi3: ecspi3grp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x10068 + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x10068 + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x1f068 + >; + }; + + pinctrl_ecspi3cs: ecspi3csgrp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0 + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b0 + MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0 + MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0 + >; + }; + + pinctrl_ecspi5: ecspi5grp { + fsl,pins = < + MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK 0x100b1 + MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI 0x100b1 + MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO 0x100b1 + >; + }; + + pinctrl_ecspi5cs: ecspi5csgrp { + fsl,pins = < + MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0 + MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x1b0b0 + MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0 + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x4001b0a8 + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0 + >; + }; + + pinctrl_gpminand: gpminandgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3_gpio: i2c3gpiogrp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b8b1 + MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001b8b1 + >; + }; + + pinctrl_weimcs: weimcsgrp { + fsl,pins = < + MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1 + MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0b1 + >; + }; + + pinctrl_weimfpga: weimfpgagrp { + fsl,pins = < + /* weim misc */ + MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1 + MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1 + MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060 + MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0b1 + MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0b1 + MX6QDL_PAD_EIM_EB0__EIM_EB0_B 0xb0b1 + MX6QDL_PAD_EIM_EB1__EIM_EB1_B 0xb0b1 + MX6QDL_PAD_EIM_EB2__EIM_EB2_B 0xb0b1 + MX6QDL_PAD_EIM_EB3__EIM_EB3_B 0xb0b1 + /* weim data */ + MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00 0x1b0b0 + MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01 0x1b0b0 + MX6QDL_PAD_CSI0_DAT4__EIM_DATA02 0x1b0b0 + MX6QDL_PAD_CSI0_DAT5__EIM_DATA03 0x1b0b0 + MX6QDL_PAD_CSI0_DAT6__EIM_DATA04 0x1b0b0 + MX6QDL_PAD_CSI0_DAT7__EIM_DATA05 0x1b0b0 + MX6QDL_PAD_CSI0_DAT8__EIM_DATA06 0x1b0b0 + MX6QDL_PAD_CSI0_DAT9__EIM_DATA07 0x1b0b0 + MX6QDL_PAD_CSI0_DAT12__EIM_DATA08 0x1b0b0 + MX6QDL_PAD_CSI0_DAT13__EIM_DATA09 0x1b0b0 + MX6QDL_PAD_CSI0_DAT14__EIM_DATA10 0x1b0b0 + MX6QDL_PAD_CSI0_DAT15__EIM_DATA11 0x1b0b0 + MX6QDL_PAD_CSI0_DAT16__EIM_DATA12 0x1b0b0 + MX6QDL_PAD_CSI0_DAT17__EIM_DATA13 0x1b0b0 + MX6QDL_PAD_CSI0_DAT18__EIM_DATA14 0x1b0b0 + MX6QDL_PAD_CSI0_DAT19__EIM_DATA15 0x1b0b0 + MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0 + MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0 + MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0 + MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0 + MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0 + MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0 + MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0 + MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0 + MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0 + MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0 + MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0 + MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0 + MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0 + MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0 + MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0 + MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0 + /* weim address */ + MX6QDL_PAD_EIM_A25__EIM_ADDR25 0xb0b1 + MX6QDL_PAD_EIM_A24__EIM_ADDR24 0xb0b1 + MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1 + MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1 + MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1 + MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1 + MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1 + MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1 + MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1 + MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1 + MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1 + MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1 + MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1 + MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1 + MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1 + MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1 + MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1 + MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1 + MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1 + MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1 + MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1 + MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1 + MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1 + MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1 + MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1 + MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_CLK__UART2_RTS_B 0x1b0b1 + MX6QDL_PAD_SD3_CMD__UART2_CTS_B 0x1b0b1 + >; + }; + + pinctrl_usbh1: usbh1grp { + fsl,pins = < + MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0 + /* usbh1_b OC */ + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 + >; + }; + + pinctrl_usbh1_hubreset: usbh1hubresetgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0 + >; + }; + + pinctrl_usbotgvbus: usbotgvbusgrp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059 + >; + }; +}; -- 2.5.0 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v2] ARM: dts: Add dts for Uniwest evi 2016-02-02 22:13 ` [PATCH v2] ARM: dts: Add dts for Uniwest evi Joshua Clayton @ 2016-02-03 9:24 ` Philipp Zabel 2016-02-03 17:37 ` [PATCH v3] " Joshua Clayton 0 siblings, 1 reply; 4+ messages in thread From: Philipp Zabel @ 2016-02-03 9:24 UTC (permalink / raw) To: linux-arm-kernel Hi Joshua, Am Dienstag, den 02.02.2016, 14:13 -0800 schrieb Joshua Clayton: > Uniwest evi is a portable electrical eddy current non-destructive > testing device. > > Signed-off-by: Joshua Clayton <stillcompiling@gmail.com> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx6q-evi.dts | 506 ++++++++++++++++++++++++++++++++++++++++ > 2 files changed, 507 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6q-evi.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index c4f42a78..4a4ef29 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -326,6 +326,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > imx6q-cubox-i.dtb \ > imx6q-dfi-fs700-m60.dtb \ > imx6q-dmo-edmqmx6.dtb \ > + imx6q-evi.dtb \ > imx6q-gk802.dtb \ > imx6q-gw51xx.dtb \ > imx6q-gw52xx.dtb \ > diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts > new file mode 100644 > index 0000000..10f566e > --- /dev/null > +++ b/arch/arm/boot/dts/imx6q-evi.dts > @@ -0,0 +1,506 @@ [...] > +/dts-v1/; > +#include "imx6q.dtsi" > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/irq.h> > + > +/ { > + model = "Uniwest Evi"; > + compatible = "uniwest,imx6q-evi", "fsl,imx6q"; [...] > + panel { > + compatible = "sharp,lq101k1ly04"; > + > + port { > + panel_in: endpoint { > + remote-endpoint = <&lvds0_out>; > + }; > + }; > + }; > +}; [...] > +&ldb { > + status = "okay"; > + > + lvds0: lvds-channel at 0 { > + fsl,data-mapping = "jeida"; > + fsl,data-width = <24>; The "sharp,lq101k1ly04" panel compatible already specifies the bus format (it is set to MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA in the simple-panel entry), these two properties can be removed. > + status = "okay"; > + > + port at 4 { > + reg = <4>; > + lvds0_out: endpoint { > + remote-endpoint = <&panel_in>; > + }; > + }; > + }; > +}; [...] regards Philipp ^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH v3] ARM: dts: Add dts for Uniwest evi 2016-02-03 9:24 ` Philipp Zabel @ 2016-02-03 17:37 ` Joshua Clayton 2016-02-14 3:28 ` Shawn Guo 0 siblings, 1 reply; 4+ messages in thread From: Joshua Clayton @ 2016-02-03 17:37 UTC (permalink / raw) To: linux-arm-kernel Uniwest evi is a portable electrical eddy current non-destructive testing device. Signed-off-by: Joshua Clayton <stillcompiling@gmail.com> --- Changes since v2: - removed fsl,data-mapping and fsl,data-width from lvds0 per Phillip Zabel - removed MX6QDL_PAD_GPIO_19__GPIO4_IO05 from hoggrp. This pin is used in a not yet upstreamed input driver. arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6q-evi.dts | 502 ++++++++++++++++++++++++++++++++++++++++ 2 files changed, 503 insertions(+) create mode 100644 arch/arm/boot/dts/imx6q-evi.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index c4f42a78..4a4ef29 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -326,6 +326,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-cubox-i.dtb \ imx6q-dfi-fs700-m60.dtb \ imx6q-dmo-edmqmx6.dtb \ + imx6q-evi.dtb \ imx6q-gk802.dtb \ imx6q-gw51xx.dtb \ imx6q-gw52xx.dtb \ diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts new file mode 100644 index 0000000..4fa5601 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-evi.dts @@ -0,0 +1,502 @@ +/* + * Copyright 2016 United Western Technologies. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + model = "Uniwest Evi"; + compatible = "uniwest,imx6q-evi", "fsl,imx6q"; + + memory { + reg = <0x10000000 0x40000000>; + }; + + reg_usbh1_vbus: regulator-usbhubreset { + compatible = "regulator-fixed"; + regulator-name = "usbh1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + startup-delay-us = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1_hubreset>; + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>; + }; + + reg_usb_otg_vbus: regulator-usbotgvbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotgvbus>; + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + panel { + compatible = "sharp,lq101k1ly04"; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; +}; + +&ecspi1 { + fsl,spi-num-chipselects = <1>; + cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1cs>; + status = "okay"; +}; + +&ecspi3 { + fsl,spi-num-chipselects = <3>; + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>, + <&gpio4 25 GPIO_ACTIVE_LOW>, + <&gpio4 26 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3cs>; + status = "okay"; +}; + +&ecspi5 { + fsl,spi-num-chipselects = <4>; + cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>, + <&gpio1 13 GPIO_ACTIVE_LOW>, + <&gpio1 12 GPIO_ACTIVE_LOW>, + <&gpio2 9 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5cs>; + status = "okay"; + + eeprom: m95m02 at 1 { + compatible = "st,m95m02", "atmel,at25"; + size = <262144>; + pagesize = <256>; + address-width = <24>; + spi-max-frequency = <5000000>; + reg = <1>; + }; + + pb_rtc: rtc at 3 { + compatible = "nxp,rtc-pcf2123"; + spi-max-frequency = <2450000>; + spi-cs-high; + reg = <3>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 25 0>; + status = "okay"; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpminand>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clock-frequency = <100000>; + status = "okay"; +}; + +&i2c3 { + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c3>; + pinctrl-1 = <&pinctrl_i2c3_gpio>; + clock-frequency = <100000>; + scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>; + status = "okay"; + + battery: sbs-battery at b { + compatible = "sbs,sbs-battery"; + reg = <0x0b>; + sbs,poll-retry-count = <100>; + sbs,i2c-retry-count = <100>; + }; +}; + +&ldb { + status = "okay"; + + lvds0: lvds-channel at 0 { + status = "okay"; + + port at 4 { + reg = <4>; + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + +&ssi1 { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usbh1_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1>; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + dr_mode = "otg"; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + non-removable; + status = "okay"; +}; + +&weim { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x08000000>; + fsl,weim-cs-gpr = <&gpr>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_weimfpga &pinctrl_weimcs>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + /* pwr mcu alert irq */ + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 + /* remainder ???? */ + MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1 + >; + }; + + pinctrl_ecspi1cs: ecspi1csgrp { + fsl,pins = < + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0 + >; + }; + + pinctrl_ecspi3: ecspi3grp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x10068 + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x10068 + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x1f068 + >; + }; + + pinctrl_ecspi3cs: ecspi3csgrp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0 + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b0 + MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0 + MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0 + >; + }; + + pinctrl_ecspi5: ecspi5grp { + fsl,pins = < + MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK 0x100b1 + MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI 0x100b1 + MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO 0x100b1 + >; + }; + + pinctrl_ecspi5cs: ecspi5csgrp { + fsl,pins = < + MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0 + MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x1b0b0 + MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0 + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x4001b0a8 + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0 + >; + }; + + pinctrl_gpminand: gpminandgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3_gpio: i2c3gpiogrp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b8b1 + MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001b8b1 + >; + }; + + pinctrl_weimcs: weimcsgrp { + fsl,pins = < + MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1 + MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0b1 + >; + }; + + pinctrl_weimfpga: weimfpgagrp { + fsl,pins = < + /* weim misc */ + MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1 + MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1 + MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060 + MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0b1 + MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0b1 + MX6QDL_PAD_EIM_EB0__EIM_EB0_B 0xb0b1 + MX6QDL_PAD_EIM_EB1__EIM_EB1_B 0xb0b1 + MX6QDL_PAD_EIM_EB2__EIM_EB2_B 0xb0b1 + MX6QDL_PAD_EIM_EB3__EIM_EB3_B 0xb0b1 + /* weim data */ + MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00 0x1b0b0 + MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01 0x1b0b0 + MX6QDL_PAD_CSI0_DAT4__EIM_DATA02 0x1b0b0 + MX6QDL_PAD_CSI0_DAT5__EIM_DATA03 0x1b0b0 + MX6QDL_PAD_CSI0_DAT6__EIM_DATA04 0x1b0b0 + MX6QDL_PAD_CSI0_DAT7__EIM_DATA05 0x1b0b0 + MX6QDL_PAD_CSI0_DAT8__EIM_DATA06 0x1b0b0 + MX6QDL_PAD_CSI0_DAT9__EIM_DATA07 0x1b0b0 + MX6QDL_PAD_CSI0_DAT12__EIM_DATA08 0x1b0b0 + MX6QDL_PAD_CSI0_DAT13__EIM_DATA09 0x1b0b0 + MX6QDL_PAD_CSI0_DAT14__EIM_DATA10 0x1b0b0 + MX6QDL_PAD_CSI0_DAT15__EIM_DATA11 0x1b0b0 + MX6QDL_PAD_CSI0_DAT16__EIM_DATA12 0x1b0b0 + MX6QDL_PAD_CSI0_DAT17__EIM_DATA13 0x1b0b0 + MX6QDL_PAD_CSI0_DAT18__EIM_DATA14 0x1b0b0 + MX6QDL_PAD_CSI0_DAT19__EIM_DATA15 0x1b0b0 + MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0 + MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0 + MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0 + MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0 + MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0 + MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0 + MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0 + MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0 + MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0 + MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0 + MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0 + MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0 + MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0 + MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0 + MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0 + MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0 + /* weim address */ + MX6QDL_PAD_EIM_A25__EIM_ADDR25 0xb0b1 + MX6QDL_PAD_EIM_A24__EIM_ADDR24 0xb0b1 + MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1 + MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1 + MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1 + MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1 + MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1 + MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1 + MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1 + MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1 + MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1 + MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1 + MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1 + MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1 + MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1 + MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1 + MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1 + MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1 + MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1 + MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1 + MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1 + MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1 + MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1 + MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1 + MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1 + MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_CLK__UART2_RTS_B 0x1b0b1 + MX6QDL_PAD_SD3_CMD__UART2_CTS_B 0x1b0b1 + >; + }; + + pinctrl_usbh1: usbh1grp { + fsl,pins = < + MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0 + /* usbh1_b OC */ + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 + >; + }; + + pinctrl_usbh1_hubreset: usbh1hubresetgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0 + >; + }; + + pinctrl_usbotgvbus: usbotgvbusgrp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059 + >; + }; +}; -- 2.5.0 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v3] ARM: dts: Add dts for Uniwest evi 2016-02-03 17:37 ` [PATCH v3] " Joshua Clayton @ 2016-02-14 3:28 ` Shawn Guo 0 siblings, 0 replies; 4+ messages in thread From: Shawn Guo @ 2016-02-14 3:28 UTC (permalink / raw) To: linux-arm-kernel On Wed, Feb 03, 2016 at 09:37:45AM -0800, Joshua Clayton wrote: > Uniwest evi is a portable electrical eddy current non-destructive > testing device. > > Signed-off-by: Joshua Clayton <stillcompiling@gmail.com> Applied, thanks. ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2016-02-14 3:28 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <patches/evidts/35215>
2016-02-02 22:13 ` [PATCH v2] ARM: dts: Add dts for Uniwest evi Joshua Clayton
2016-02-03 9:24 ` Philipp Zabel
2016-02-03 17:37 ` [PATCH v3] " Joshua Clayton
2016-02-14 3:28 ` Shawn Guo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).