* [PATCHv2 1/8] ARM: dts: imx6-tx6: Relicense the Ka-Ro DT files under GPLv2/X11
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
@ 2016-03-08 8:03 ` Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 2/8] ARM: dts: imx6-tx6: cleanup; no functional change Lothar Waßmann
` (8 subsequent siblings)
9 siblings, 0 replies; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-08 8:03 UTC (permalink / raw)
To: linux-arm-kernel
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the imx6*-tx6* files to this combination.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6dl-tx6dl-comtft.dts | 42 ++++++++++++++++++++++++----
arch/arm/boot/dts/imx6dl-tx6u-801x.dts | 42 ++++++++++++++++++++++++----
arch/arm/boot/dts/imx6dl-tx6u-811x.dts | 42 ++++++++++++++++++++++++----
arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts | 42 ++++++++++++++++++++++++----
arch/arm/boot/dts/imx6q-tx6q-1010.dts | 42 ++++++++++++++++++++++++----
arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts | 42 ++++++++++++++++++++++++----
arch/arm/boot/dts/imx6q-tx6q-1020.dts | 42 ++++++++++++++++++++++++----
arch/arm/boot/dts/imx6q-tx6q-1110.dts | 42 ++++++++++++++++++++++++----
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 42 ++++++++++++++++++++++++----
9 files changed, 324 insertions(+), 54 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-tx6dl-comtft.dts b/arch/arm/boot/dts/imx6dl-tx6dl-comtft.dts
index 913bb9a..063fe75 100644
--- a/arch/arm/boot/dts/imx6dl-tx6dl-comtft.dts
+++ b/arch/arm/boot/dts/imx6dl-tx6dl-comtft.dts
@@ -1,12 +1,42 @@
/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-801x.dts b/arch/arm/boot/dts/imx6dl-tx6u-801x.dts
index 5fe465c..b7a7284 100644
--- a/arch/arm/boot/dts/imx6dl-tx6u-801x.dts
+++ b/arch/arm/boot/dts/imx6dl-tx6u-801x.dts
@@ -1,12 +1,42 @@
/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
index d35a5cd..a1b755a 100644
--- a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
+++ b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
@@ -1,12 +1,42 @@
/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts b/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts
index b18fae1..65e95ae 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts
+++ b/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts
@@ -1,12 +1,42 @@
/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1010.dts b/arch/arm/boot/dts/imx6q-tx6q-1010.dts
index b58ec9c..20cd0e7 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1010.dts
+++ b/arch/arm/boot/dts/imx6q-tx6q-1010.dts
@@ -1,12 +1,42 @@
/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts b/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts
index 0bb9a9d..19231a0 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts
+++ b/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts
@@ -1,12 +1,42 @@
/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1020.dts b/arch/arm/boot/dts/imx6q-tx6q-1020.dts
index b96d80a..4217282 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1020.dts
+++ b/arch/arm/boot/dts/imx6q-tx6q-1020.dts
@@ -1,12 +1,42 @@
/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1110.dts b/arch/arm/boot/dts/imx6q-tx6q-1110.dts
index 2792da9..45ceee7 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1110.dts
+++ b/arch/arm/boot/dts/imx6q-tx6q-1110.dts
@@ -1,12 +1,42 @@
/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index efd06b5..5d348d9 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -1,12 +1,42 @@
/*
- * Copyright 2014 Lothar Wa?mann <LW@KARO-electronics.de>
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
*
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
*/
#include <dt-bindings/gpio/gpio.h>
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv2 2/8] ARM: dts: imx6-tx6: cleanup; no functional change
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 1/8] ARM: dts: imx6-tx6: Relicense the Ka-Ro DT files under GPLv2/X11 Lothar Waßmann
@ 2016-03-08 8:03 ` Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 3/8] ARM: dts: imx6-tx6: remove regulator bus Lothar Waßmann
` (7 subsequent siblings)
9 siblings, 0 replies; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-08 8:03 UTC (permalink / raw)
To: linux-arm-kernel
Add an empty line between properties and subnode in the clocks node.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index 5d348d9..912f284 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -67,6 +67,7 @@
clocks {
#address-cells = <1>;
#size-cells = <0>;
+
mclk: clock at 0 {
compatible = "fixed-clock";
reg = <0>;
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv2 3/8] ARM: dts: imx6-tx6: remove regulator bus
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 1/8] ARM: dts: imx6-tx6: Relicense the Ka-Ro DT files under GPLv2/X11 Lothar Waßmann
2016-03-08 8:03 ` [PATCHv2 2/8] ARM: dts: imx6-tx6: cleanup; no functional change Lothar Waßmann
@ 2016-03-08 8:03 ` Lothar Waßmann
2016-03-31 6:00 ` Shawn Guo
2016-03-08 8:04 ` [PATCHv2 4/8] ARM: dts: imx6-tx6: disable the spi node by default Lothar Waßmann
` (6 subsequent siblings)
9 siblings, 1 reply; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-08 8:03 UTC (permalink / raw)
To: linux-arm-kernel
DT maintainers don't like the 'simple-bus' container around the
regulator nodes. So remove it.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 178 +++++++++++++++++--------------------
1 file changed, 81 insertions(+), 97 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index 912f284..ec374f5 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -97,104 +97,88 @@
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
+ reg_3v3_etn: reg-3v3-etn {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3_ETN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etnphy_power>;
+ gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
- reg_3v3_etn: regulator at 0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "3V3_ETN";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_etnphy_power>;
- gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- reg_2v5: regulator at 1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "2V5";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2500000>;
- regulator-always-on;
- };
-
- reg_3v3: regulator at 2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- reg_can_xcvr: regulator at 3 {
- compatible = "regulator-fixed";
- reg = <3>;
- regulator-name = "CAN XCVR";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_flexcan_xcvr>;
- gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
- enable-active-low;
- };
-
- reg_lcd0_pwr: regulator at 4 {
- compatible = "regulator-fixed";
- reg = <4>;
- regulator-name = "LCD0 POWER";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_lcd0_pwr>;
- gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_lcd1_pwr: regulator at 5 {
- compatible = "regulator-fixed";
- reg = <5>;
- regulator-name = "LCD1 POWER";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_lcd1_pwr>;
- gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- regulator-always-on;
- };
-
- reg_usbh1_vbus: regulator at 6 {
- compatible = "regulator-fixed";
- reg = <6>;
- regulator-name = "usbh1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbh1_vbus>;
- gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- reg_usbotg_vbus: regulator at 7 {
- compatible = "regulator-fixed";
- reg = <7>;
- regulator-name = "usbotg_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg_vbus>;
- gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
+ reg_2v5: reg-2v5 {
+ compatible = "regulator-fixed";
+ regulator-name = "2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3v3: reg-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_can_xcvr: reg-can-xcvr {
+ compatible = "regulator-fixed";
+ regulator-name = "CAN XCVR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan_xcvr>;
+ gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
+ enable-active-low;
+ };
+
+ reg_lcd0_pwr: reg-lcd0-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD0 POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd0_pwr>;
+ gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ reg_lcd1_pwr: reg-lcd1-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD1 POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd1_pwr>;
+ gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ reg_usbh1_vbus: reg-usbh1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_vbus>;
+ gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usbotg_vbus: reg-usbotg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbotg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_vbus>;
+ gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
};
sound {
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv2 3/8] ARM: dts: imx6-tx6: remove regulator bus
2016-03-08 8:03 ` [PATCHv2 3/8] ARM: dts: imx6-tx6: remove regulator bus Lothar Waßmann
@ 2016-03-31 6:00 ` Shawn Guo
0 siblings, 0 replies; 21+ messages in thread
From: Shawn Guo @ 2016-03-31 6:00 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Mar 08, 2016 at 09:03:59AM +0100, Lothar Wa?mann wrote:
> DT maintainers don't like the 'simple-bus' container around the
> regulator nodes. So remove it.
>
> Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
> ---
> arch/arm/boot/dts/imx6qdl-tx6.dtsi | 178 +++++++++++++++++--------------------
> 1 file changed, 81 insertions(+), 97 deletions(-)
>
> diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
> index 912f284..ec374f5 100644
> --- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
> @@ -97,104 +97,88 @@
> };
> };
>
> - regulators {
> - compatible = "simple-bus";
> - #address-cells = <1>;
> - #size-cells = <0>;
> + reg_3v3_etn: reg-3v3-etn {
Please use the following naming schema for fixed regulators.
reg_xxx: regulator-xxx {
...
}
Shawn
> + compatible = "regulator-fixed";
> + regulator-name = "3V3_ETN";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_etnphy_power>;
> + gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
>
> - reg_3v3_etn: regulator at 0 {
> - compatible = "regulator-fixed";
> - reg = <0>;
> - regulator-name = "3V3_ETN";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_etnphy_power>;
> - gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - };
> -
> - reg_2v5: regulator at 1 {
> - compatible = "regulator-fixed";
> - reg = <1>;
> - regulator-name = "2V5";
> - regulator-min-microvolt = <2500000>;
> - regulator-max-microvolt = <2500000>;
> - regulator-always-on;
> - };
> -
> - reg_3v3: regulator at 2 {
> - compatible = "regulator-fixed";
> - reg = <2>;
> - regulator-name = "3V3";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - };
> -
> - reg_can_xcvr: regulator at 3 {
> - compatible = "regulator-fixed";
> - reg = <3>;
> - regulator-name = "CAN XCVR";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_flexcan_xcvr>;
> - gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
> - enable-active-low;
> - };
> -
> - reg_lcd0_pwr: regulator at 4 {
> - compatible = "regulator-fixed";
> - reg = <4>;
> - regulator-name = "LCD0 POWER";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_lcd0_pwr>;
> - gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - reg_lcd1_pwr: regulator at 5 {
> - compatible = "regulator-fixed";
> - reg = <5>;
> - regulator-name = "LCD1 POWER";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_lcd1_pwr>;
> - gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - reg_usbh1_vbus: regulator at 6 {
> - compatible = "regulator-fixed";
> - reg = <6>;
> - regulator-name = "usbh1_vbus";
> - regulator-min-microvolt = <5000000>;
> - regulator-max-microvolt = <5000000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usbh1_vbus>;
> - gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - };
> -
> - reg_usbotg_vbus: regulator at 7 {
> - compatible = "regulator-fixed";
> - reg = <7>;
> - regulator-name = "usbotg_vbus";
> - regulator-min-microvolt = <5000000>;
> - regulator-max-microvolt = <5000000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usbotg_vbus>;
> - gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - };
> + reg_2v5: reg-2v5 {
> + compatible = "regulator-fixed";
> + regulator-name = "2V5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-always-on;
> + };
> +
> + reg_3v3: reg-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_can_xcvr: reg-can-xcvr {
> + compatible = "regulator-fixed";
> + regulator-name = "CAN XCVR";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan_xcvr>;
> + gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
> + enable-active-low;
> + };
> +
> + reg_lcd0_pwr: reg-lcd0-pwr {
> + compatible = "regulator-fixed";
> + regulator-name = "LCD0 POWER";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + };
> +
> + reg_lcd1_pwr: reg-lcd1-pwr {
> + compatible = "regulator-fixed";
> + regulator-name = "LCD1 POWER";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd1_pwr>;
> + gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + };
> +
> + reg_usbh1_vbus: reg-usbh1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usbh1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh1_vbus>;
> + gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usbotg_vbus: reg-usbotg-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usbotg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg_vbus>;
> + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> };
>
> sound {
> --
> 2.1.4
>
>
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCHv2 4/8] ARM: dts: imx6-tx6: disable the spi node by default
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
` (2 preceding siblings ...)
2016-03-08 8:03 ` [PATCHv2 3/8] ARM: dts: imx6-tx6: remove regulator bus Lothar Waßmann
@ 2016-03-08 8:04 ` Lothar Waßmann
2016-03-08 8:04 ` [PATCHv2 5/8] ARM: dts: imx6-tx6: remove container node around pinctrl nodes Lothar Waßmann
` (5 subsequent siblings)
9 siblings, 0 replies; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-08 8:04 UTC (permalink / raw)
To: linux-arm-kernel
The spidev driver doesn't like to be instantiated via a naked 'spidev'
compatible, though it is very convenient to invoke it this way without
a dedicated SPI device for basic functional testing.
Disable the spi node by default to silence the WARN_ON() from the
spidev driver, but leave the configuration intact otherwise.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index ec374f5..9509b44 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -224,7 +224,7 @@
&gpio2 30 GPIO_ACTIVE_HIGH
&gpio3 19 GPIO_ACTIVE_HIGH
>;
- status = "okay";
+ status = "disabled";
spidev0: spi at 0 {
compatible = "spidev";
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv2 5/8] ARM: dts: imx6-tx6: remove container node around pinctrl nodes
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
` (3 preceding siblings ...)
2016-03-08 8:04 ` [PATCHv2 4/8] ARM: dts: imx6-tx6: disable the spi node by default Lothar Waßmann
@ 2016-03-08 8:04 ` Lothar Waßmann
2016-03-08 8:04 ` [PATCHv2 6/8] ARM: dts: imx6qdl-tx6: add mdio node for ethernet phy Lothar Waßmann
` (4 subsequent siblings)
9 siblings, 0 replies; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-08 8:04 UTC (permalink / raw)
To: linux-arm-kernel
Remove the function node around the pinctrl nodes that was obsoleted
by commit 5fcdf6a7ed95 ("pinctrl: imx: Allow parsing DT without
function nodes"), we can save this container node.
Also move the iomux node to the bottom of the file to improve
readability of the file.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6dl-tx6u-811x.dts | 18 +-
arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts | 30 +-
arch/arm/boot/dts/imx6q-tx6q-1020.dts | 30 +-
arch/arm/boot/dts/imx6q-tx6q-1110.dts | 18 +-
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 551 ++++++++++++++-------------
5 files changed, 321 insertions(+), 326 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
index a1b755a..5e0c6bb 100644
--- a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
+++ b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
@@ -111,16 +111,6 @@
};
};
-&iomuxc {
- imx6dl-tx6u-811x {
- pinctrl_eeti: eetigrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
- >;
- };
- };
-};
-
&kpp {
status = "disabled"; /* pad conflict with backlight1 PWM */
};
@@ -178,3 +168,11 @@
&pwm1 {
status = "okay";
};
+
+&iomuxc {
+ pinctrl_eeti: eetigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts b/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts
index 19231a0..9ed243b 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts
+++ b/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts
@@ -124,22 +124,6 @@
status = "disabled";
};
-&iomuxc {
- imx6qdl-tx6 {
- pinctrl_usdhc4: usdhc4grp {
- fsl,pins = <
- MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
- MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
- MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
- MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
- MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
- MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
- MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
- >;
- };
- };
-};
-
&ipu1_di0_disp0 {
remote-endpoint = <&display0_in>;
};
@@ -164,3 +148,17 @@
fsl,wp-controller;
status = "okay";
};
+
+&iomuxc {
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
+ MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1020.dts b/arch/arm/boot/dts/imx6q-tx6q-1020.dts
index 4217282..347b531 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1020.dts
+++ b/arch/arm/boot/dts/imx6q-tx6q-1020.dts
@@ -210,22 +210,6 @@
status = "disabled";
};
-&iomuxc {
- imx6qdl-tx6 {
- pinctrl_usdhc4: usdhc4grp {
- fsl,pins = <
- MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
- MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
- MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
- MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
- MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
- MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
- MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
- >;
- };
- };
-};
-
&ipu1_di0_disp0 {
remote-endpoint = <&display0_in>;
};
@@ -238,3 +222,17 @@
fsl,wp-controller;
status = "okay";
};
+
+&iomuxc {
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
+ MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1110.dts b/arch/arm/boot/dts/imx6q-tx6q-1110.dts
index 45ceee7..0433e22 100644
--- a/arch/arm/boot/dts/imx6q-tx6q-1110.dts
+++ b/arch/arm/boot/dts/imx6q-tx6q-1110.dts
@@ -111,16 +111,6 @@
};
};
-&iomuxc {
- imx6q-tx6q-1110 {
- pinctrl_eeti: eetigrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
- >;
- };
- };
-};
-
&kpp {
status = "disabled"; /* pad conflict with backlight1 PWM */
};
@@ -182,3 +172,11 @@
&sata {
status = "okay";
};
+
+&iomuxc {
+ pinctrl_eeti: eetigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index 9509b44..dc813c2 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -316,310 +316,313 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
- imx6qdl-tx6 {
- pinctrl_hog: hoggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */
- MX6QDL_PAD_SD3_DAT2__GPIO7_IO06 0x1b0b1 /* ETN PHY RESET */
- MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b1 /* ETN PHY INT */
- MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b1 /* PWR BTN */
- >;
- };
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */
+ MX6QDL_PAD_SD3_DAT2__GPIO7_IO06 0x1b0b1 /* ETN PHY RESET */
+ MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b1 /* ETN PHY INT */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b1 /* PWR BTN */
+ >;
+ };
- pinctrl_audmux: audmuxgrp {
- fsl,pins = <
- MX6QDL_PAD_KEY_ROW1__AUD5_RXD 0x130b0 /* SSI1_RXD */
- MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x110b0 /* SSI1_TXD */
- MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0 /* SSI1_CLK */
- MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x130b0 /* SSI1_FS */
- >;
- };
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW1__AUD5_RXD 0x130b0 /* SSI1_RXD */
+ MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x110b0 /* SSI1_TXD */
+ MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0 /* SSI1_CLK */
+ MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x130b0 /* SSI1_FS */
+ >;
+ };
- pinctrl_disp0_1: disp0grp-1 {
- fsl,pins = <
- MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
- MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
- MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
- MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
- /* PAD DISP0_DAT0 is used for the Flexcan transceiver control */
- MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
- MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
- MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
- MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
- MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
- MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
- MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
- MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
- MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
- MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
- MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
- MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
- MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
- MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
- MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
- MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
- MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
- MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
- MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
- MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
- MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
- MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
- MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
- >;
- };
+ pinctrl_disp0_1: disp0grp-1 {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ /* PAD DISP0_DAT0 is used for the Flexcan transceiver control */
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
+ >;
+ };
- pinctrl_disp0_2: disp0grp-2 {
- fsl,pins = <
- MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
- MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
- MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
- MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
- MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
- MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
- MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
- MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
- MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
- MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
- MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
- MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
- MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
- MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
- MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
- MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
- MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
- MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
- MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
- MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
- MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
- MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
- MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
- MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
- MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
- MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
- MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
- MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
- >;
- };
+ pinctrl_disp0_2: disp0grp-2 {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
+ >;
+ };
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x0b0b0
- MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x0b0b0
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x0b0b0
- MX6QDL_PAD_GPIO_19__ECSPI1_RDY 0x0b0b0
- MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x0b0b0 /* SPI CS0 */
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x0b0b0 /* SPI CS1 */
- >;
- };
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x0b0b0
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x0b0b0
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x0b0b0
+ MX6QDL_PAD_GPIO_19__ECSPI1_RDY 0x0b0b0
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x0b0b0 /* SPI CS0 */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x0b0b0 /* SPI CS1 */
+ >;
+ };
- pinctrl_edt_ft5x06: edt-ft5x06grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 /* Interrupt */
- MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b0b0 /* Reset */
- MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0 /* Wake */
- >;
- };
+ pinctrl_edt_ft5x06: edt-ft5x06grp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 /* Interrupt */
+ MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b0b0 /* Reset */
+ MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0 /* Wake */
+ >;
+ };
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
- MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
- MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
- >;
- };
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+ >;
+ };
- pinctrl_etnphy_power: etnphy-pwrgrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1 /* ETN PHY POWER */
- >;
- };
+ pinctrl_enet_mdio: enet-mdiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ >;
+ };
- pinctrl_flexcan1: flexcan1grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
- MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
- >;
- };
+ pinctrl_etnphy_power: etnphy-pwrgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1 /* ETN PHY POWER */
+ >;
+ };
- pinctrl_flexcan2: flexcan2grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b0b0
- MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b0b0
- >;
- };
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
+ MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
+ >;
+ };
- pinctrl_flexcan_xcvr: flexcan-xcvrgrp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x1b0b0 /* Flexcan XCVR enable */
- >;
- };
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b0b0
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b0b0
+ >;
+ };
- pinctrl_gpmi_nand: gpminandgrp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_CLE__NAND_CLE 0x0b0b1
- MX6QDL_PAD_NANDF_ALE__NAND_ALE 0x0b0b1
- MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0x0b0b1
- MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0x0b000
- MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0x0b0b1
- MX6QDL_PAD_SD4_CMD__NAND_RE_B 0x0b0b1
- MX6QDL_PAD_SD4_CLK__NAND_WE_B 0x0b0b1
- MX6QDL_PAD_NANDF_D0__NAND_DATA00 0x0b0b1
- MX6QDL_PAD_NANDF_D1__NAND_DATA01 0x0b0b1
- MX6QDL_PAD_NANDF_D2__NAND_DATA02 0x0b0b1
- MX6QDL_PAD_NANDF_D3__NAND_DATA03 0x0b0b1
- MX6QDL_PAD_NANDF_D4__NAND_DATA04 0x0b0b1
- MX6QDL_PAD_NANDF_D5__NAND_DATA05 0x0b0b1
- MX6QDL_PAD_NANDF_D6__NAND_DATA06 0x0b0b1
- MX6QDL_PAD_NANDF_D7__NAND_DATA07 0x0b0b1
- >;
- };
+ pinctrl_flexcan_xcvr: flexcan-xcvrgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x1b0b0 /* Flexcan XCVR enable */
+ >;
+ };
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
- MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
- >;
- };
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0x0b0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0x0b0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0x0b0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0x0b000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0x0b0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0x0b0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0x0b0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0x0b0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0x0b0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0x0b0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0x0b0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0x0b0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0x0b0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0x0b0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0x0b0b1
+ >;
+ };
- pinctrl_i2c3: i2c3grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
- MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
- >;
- };
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
- pinctrl_kpp: kppgrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_9__KEY_COL6 0x1b0b1
- MX6QDL_PAD_GPIO_4__KEY_COL7 0x1b0b1
- MX6QDL_PAD_KEY_COL2__KEY_COL2 0x1b0b1
- MX6QDL_PAD_KEY_COL3__KEY_COL3 0x1b0b1
- MX6QDL_PAD_GPIO_2__KEY_ROW6 0x1b0b1
- MX6QDL_PAD_GPIO_5__KEY_ROW7 0x1b0b1
- MX6QDL_PAD_KEY_ROW2__KEY_ROW2 0x1b0b1
- MX6QDL_PAD_KEY_ROW3__KEY_ROW3 0x1b0b1
- >;
- };
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
- pinctrl_lcd0_pwr: lcd0-pwrgrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b1 /* LCD Reset */
- >;
- };
+ pinctrl_kpp: kppgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__KEY_COL6 0x1b0b1
+ MX6QDL_PAD_GPIO_4__KEY_COL7 0x1b0b1
+ MX6QDL_PAD_KEY_COL2__KEY_COL2 0x1b0b1
+ MX6QDL_PAD_KEY_COL3__KEY_COL3 0x1b0b1
+ MX6QDL_PAD_GPIO_2__KEY_ROW6 0x1b0b1
+ MX6QDL_PAD_GPIO_5__KEY_ROW7 0x1b0b1
+ MX6QDL_PAD_KEY_ROW2__KEY_ROW2 0x1b0b1
+ MX6QDL_PAD_KEY_ROW3__KEY_ROW3 0x1b0b1
+ >;
+ };
- pinctrl_lcd1_pwr: lcd1-pwrgrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x1b0b1 /* LCD Power Enable */
- >;
- };
+ pinctrl_lcd0_pwr: lcd0-pwrgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b1 /* LCD Reset */
+ >;
+ };
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1
- >;
- };
+ pinctrl_lcd1_pwr: lcd-pwrgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x1b0b1 /* LCD Power Enable */
+ >;
+ };
- pinctrl_pwm2: pwm2grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
- >;
- };
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1
+ >;
+ };
- pinctrl_tsc2007: tsc2007grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x1b0b0 /* Interrupt */
- >;
- };
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
+ >;
+ };
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
- MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
- >;
- };
+ pinctrl_tsc2007: tsc2007grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x1b0b0 /* Interrupt */
+ >;
+ };
- pinctrl_uart1_rtscts: uart1_rtsctsgrp {
- fsl,pins = <
- MX6QDL_PAD_SD3_DAT1__UART1_RTS_B 0x1b0b1
- MX6QDL_PAD_SD3_DAT0__UART1_CTS_B 0x1b0b1
- >;
- };
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+ >;
+ };
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
- MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
- >;
- };
+ pinctrl_uart1_rtscts: uart1_rtsctsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT1__UART1_RTS_B 0x1b0b1
+ MX6QDL_PAD_SD3_DAT0__UART1_CTS_B 0x1b0b1
+ >;
+ };
- pinctrl_uart2_rtscts: uart2_rtsctsgrp {
- fsl,pins = <
- MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1
- MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1
- >;
- };
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ >;
+ };
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
- >;
- };
+ pinctrl_uart2_rtscts: uart2_rtsctsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1
+ MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1
+ >;
+ };
- pinctrl_uart3_rtscts: uart3_rtsctsgrp {
- fsl,pins = <
- MX6QDL_PAD_SD3_DAT3__UART3_CTS_B 0x1b0b1
- MX6QDL_PAD_SD3_RST__UART3_RTS_B 0x1b0b1
- >;
- };
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ >;
+ };
- pinctrl_usbh1_vbus: usbh1-vbusgrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0 /* USBH1_VBUSEN */
- >;
- };
+ pinctrl_uart3_rtscts: uart3_rtsctsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT3__UART3_CTS_B 0x1b0b1
+ MX6QDL_PAD_SD3_RST__UART3_RTS_B 0x1b0b1
+ >;
+ };
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x17059
- >;
- };
+ pinctrl_usbh1_vbus: usbh1-vbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0 /* USBH1_VBUSEN */
+ >;
+ };
- pinctrl_usbotg_vbus: usbotg-vbusgrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0 /* USBOTG_VBUSEN */
- >;
- };
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x17059
+ >;
+ };
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1
- MX6QDL_PAD_SD1_CLK__SD1_CLK 0x070b1
- MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1
- MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1
- MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1
- MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1
- MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */
- >;
- };
+ pinctrl_usbotg_vbus: usbotg-vbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0 /* USBOTG_VBUSEN */
+ >;
+ };
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX6QDL_PAD_SD2_CMD__SD2_CMD 0x070b1
- MX6QDL_PAD_SD2_CLK__SD2_CLK 0x070b1
- MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x070b1
- MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x070b1
- MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x070b1
- MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x070b1
- MX6QDL_PAD_SD3_CLK__GPIO7_IO03 0x170b0 /* SD2 CD */
- >;
- };
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x070b1
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1
+ MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x070b1
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x070b1
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x070b1
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x070b1
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x070b1
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x070b1
+ MX6QDL_PAD_SD3_CLK__GPIO7_IO03 0x170b0 /* SD2 CD */
+ >;
};
};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv2 6/8] ARM: dts: imx6qdl-tx6: add mdio node for ethernet phy
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
` (4 preceding siblings ...)
2016-03-08 8:04 ` [PATCHv2 5/8] ARM: dts: imx6-tx6: remove container node around pinctrl nodes Lothar Waßmann
@ 2016-03-08 8:04 ` Lothar Waßmann
2016-03-08 8:04 ` [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
` (3 subsequent siblings)
9 siblings, 0 replies; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-08 8:04 UTC (permalink / raw)
To: linux-arm-kernel
Add mdio node and an appropriate PHY configuration to enable use of
the PHY interrupt for link status changes.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index dc813c2..a0d59ab 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -249,8 +249,22 @@
clock-names = "ipg", "ahb", "ptp", "enet_out";
phy-mode = "rmii";
phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_HIGH>;
+ phy-handle = <&etnphy>;
phy-supply = <®_3v3_etn>;
status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ etnphy: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet_mdio>;
+ interrupts-extended = <&gpio7 1 IRQ_TYPE_EDGE_FALLING>;
+ };
+ };
};
&gpmi {
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
` (5 preceding siblings ...)
2016-03-08 8:04 ` [PATCHv2 6/8] ARM: dts: imx6qdl-tx6: add mdio node for ethernet phy Lothar Waßmann
@ 2016-03-08 8:04 ` Lothar Waßmann
2016-03-31 6:10 ` Shawn Guo
2016-03-08 8:04 ` [PATCHv2 8/8] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard Lothar Waßmann
` (2 subsequent siblings)
9 siblings, 1 reply; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-08 8:04 UTC (permalink / raw)
To: linux-arm-kernel
Add support for the following i.MX6 based modules from Ka-Ro
electronics GmbH:
TX6S-8034:
Processor Freescale i.MX 6 Solo, 800MHz
RAM 256MiB DDR3 SDRAM
ROM 128MiB NAND Flash
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
TX6S-8035:
Processor Freescale i.MX 6 Solo, 800MHz
RAM 512MiB DDR3 SDRAM
ROM 4GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
TX6U-8033:
Processor Freescale i.MX 6 Dual Lite, 800MHz
RAM 1GiB DDR3 SDRAM
ROM 4GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
TX6Q-1036:
Processor Freescale i.MX 6Quad, 1GHz
RAM 1GB DDR3 SDRAM 64-bit
ROM 8GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range Extended Consumer Grade (-20?C to 105?C Tj)
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 4 +
arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 249 ++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6dl-tx6s-8035.dts | 246 +++++++++++++++++++++++++++
arch/arm/boot/dts/imx6dl-tx6u-8033.dts | 248 +++++++++++++++++++++++++++
arch/arm/boot/dts/imx6q-tx6q-1036.dts | 295 +++++++++++++++++++++++++++++++++
5 files changed, 1042 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts
create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8035.dts
create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-8033.dts
create mode 100644 arch/arm/boot/dts/imx6q-tx6q-1036.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 072294f..71b5cd3 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -320,6 +320,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \
imx6dl-tx6dl-comtft.dtb \
+ imx6dl-tx6s-8034.dtb \
+ imx6dl-tx6s-8035.dtb \
+ imx6dl-tx6u-8033.dtb \
imx6dl-tx6u-801x.dtb \
imx6dl-tx6u-811x.dtb \
imx6dl-udoo.dtb \
@@ -360,6 +363,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-tx6q-1010-comtft.dtb \
imx6q-tx6q-1020.dtb \
imx6q-tx6q-1020-comtft.dtb \
+ imx6q-tx6q-1036.dtb \
imx6q-tx6q-1110.dtb \
imx6q-udoo.dtb \
imx6q-wandboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
new file mode 100644
index 0000000..0d3df6e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
@@ -0,0 +1,237 @@
+/*
+ * Copyright 2015-2016 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6S-8034 Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &display;
+ ipu1 = &ipu1;
+ };
+
+ cpus {
+ /delete-node/ cpu at 1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd0_pwr>;
+ enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_2>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ native-mode = <&vga>;
+
+ vga: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&pinctrl_usdhc1 {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x07099
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1
+ MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */
+ >;
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+®_lcd0_pwr {
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8035.dts b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
new file mode 100644
index 0000000..2f9efdb
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
@@ -0,0 +1,253 @@
+/*
+ * Copyright 2015-2016 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6S-8035 Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &display;
+ ipu1 = &ipu1;
+ };
+
+ cpus {
+ /delete-node/ cpu at 1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd0_pwr>;
+ enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_2>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ native-mode = <&vga>;
+
+ vga: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+®_lcd0_pwr {
+ status = "disabled";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <4>;
+ non-removable;
+ no-1-8-v;
+ fsl,wp-controller;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
+ MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-8033.dts b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
new file mode 100644
index 0000000..4d3204a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
@@ -0,0 +1,248 @@
+/*
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6U-8033 Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &display;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd0_pwr>;
+ enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_2>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ native-mode = <&vga>;
+
+ vga: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+®_lcd0_pwr {
+ status = "disabled";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <4>;
+ non-removable;
+ no-1-8-v;
+ fsl,wp-controller;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
+ MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1036.dts b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
new file mode 100644
index 0000000..70c478b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
@@ -0,0 +1,252 @@
+/*
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6Q-1036 Module";
+ compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+
+ aliases {
+ display = &display;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd0_pwr>;
+ enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_2>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ native-mode = <&vga>;
+
+ vga: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+&ipu2 {
+ status = "disabled";
+};
+
+®_lcd0_pwr {
+ status = "disabled";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <4>;
+ non-removable;
+ no-1-8-v;
+ fsl,wp-controller;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
+ MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
+ >;
+ };
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules
2016-03-08 8:04 ` [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
@ 2016-03-31 6:10 ` Shawn Guo
2016-03-31 6:29 ` Lothar Waßmann
0 siblings, 1 reply; 21+ messages in thread
From: Shawn Guo @ 2016-03-31 6:10 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Mar 08, 2016 at 09:04:03AM +0100, Lothar Wa?mann wrote:
> Add support for the following i.MX6 based modules from Ka-Ro
> electronics GmbH:
> TX6S-8034:
> Processor Freescale i.MX 6 Solo, 800MHz
> RAM 256MiB DDR3 SDRAM
> ROM 128MiB NAND Flash
> Power supply Single 3.1V to 5.5V
> Size 31mm SO-DIMM
> Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
>
> TX6S-8035:
> Processor Freescale i.MX 6 Solo, 800MHz
> RAM 512MiB DDR3 SDRAM
> ROM 4GiB eMMC
> Power supply Single 3.1V to 5.5V
> Size 31mm SO-DIMM
> Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
>
> TX6U-8033:
> Processor Freescale i.MX 6 Dual Lite, 800MHz
> RAM 1GiB DDR3 SDRAM
> ROM 4GiB eMMC
> Power supply Single 3.1V to 5.5V
> Size 31mm SO-DIMM
> Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
>
> TX6Q-1036:
> Processor Freescale i.MX 6Quad, 1GHz
> RAM 1GB DDR3 SDRAM 64-bit
> ROM 8GiB eMMC
> Power supply Single 3.1V to 5.5V
> Size 31mm SO-DIMM
> Temp. Range Extended Consumer Grade (-20?C to 105?C Tj)
>
> Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
> ---
> arch/arm/boot/dts/Makefile | 4 +
> arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 249 ++++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6dl-tx6s-8035.dts | 246 +++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6dl-tx6u-8033.dts | 248 +++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6q-tx6q-1036.dts | 295 +++++++++++++++++++++++++++++++++
> 5 files changed, 1042 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8035.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-8033.dts
> create mode 100644 arch/arm/boot/dts/imx6q-tx6q-1036.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 072294f..71b5cd3 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -320,6 +320,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-sabrelite.dtb \
> imx6dl-sabresd.dtb \
> imx6dl-tx6dl-comtft.dtb \
> + imx6dl-tx6s-8034.dtb \
> + imx6dl-tx6s-8035.dtb \
> + imx6dl-tx6u-8033.dtb \
imx6dl-tx6u-8033.dtb should go after imx6dl-tx6u-801x.dtb?
Shawn
> imx6dl-tx6u-801x.dtb \
> imx6dl-tx6u-811x.dtb \
> imx6dl-udoo.dtb \
> @@ -360,6 +363,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-tx6q-1010-comtft.dtb \
> imx6q-tx6q-1020.dtb \
> imx6q-tx6q-1020-comtft.dtb \
> + imx6q-tx6q-1036.dtb \
> imx6q-tx6q-1110.dtb \
> imx6q-udoo.dtb \
> imx6q-wandboard.dtb \
> diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
> new file mode 100644
> index 0000000..0d3df6e
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
> @@ -0,0 +1,237 @@
> +/*
> + * Copyright 2015-2016 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6S-8034 Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> +
> + aliases {
> + display = &display;
> + ipu1 = &ipu1;
> + };
> +
> + cpus {
> + /delete-node/ cpu at 1;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_lcd1_pwr>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display at di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + native-mode = <&vga>;
> +
> + vga: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ds1339 {
> + status = "disabled";
> +};
> +
> +&pinctrl_usdhc1 {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x07099
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1
> + MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */
> + >;
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +®_lcd0_pwr {
> + status = "disabled";
> +};
> diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8035.dts b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
> new file mode 100644
> index 0000000..2f9efdb
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
> @@ -0,0 +1,253 @@
> +/*
> + * Copyright 2015-2016 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6S-8035 Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> +
> + aliases {
> + display = &display;
> + ipu1 = &ipu1;
> + };
> +
> + cpus {
> + /delete-node/ cpu at 1;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_lcd1_pwr>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display at di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + native-mode = <&vga>;
> +
> + vga: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ds1339 {
> + status = "disabled";
> +};
> +
> +&gpmi {
> + status = "disabled";
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +®_lcd0_pwr {
> + status = "disabled";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <4>;
> + non-removable;
> + no-1-8-v;
> + fsl,wp-controller;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_usdhc4: usdhc4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
> + MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
> + >;
> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6dl-tx6u-8033.dts b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
> new file mode 100644
> index 0000000..4d3204a
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
> @@ -0,0 +1,248 @@
> +/*
> + * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6U-8033 Module";
> + compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
> +
> + aliases {
> + display = &display;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_lcd1_pwr>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display at di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + native-mode = <&vga>;
> +
> + vga: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ds1339 {
> + status = "disabled";
> +};
> +
> +&gpmi {
> + status = "disabled";
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +®_lcd0_pwr {
> + status = "disabled";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <4>;
> + non-removable;
> + no-1-8-v;
> + fsl,wp-controller;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_usdhc4: usdhc4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
> + MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
> + >;
> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6q-tx6q-1036.dts b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
> new file mode 100644
> index 0000000..70c478b
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
> @@ -0,0 +1,252 @@
> +/*
> + * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include "imx6qdl-tx6.dtsi"
> +
> +/ {
> + model = "Ka-Ro electronics TX6Q-1036 Module";
> + compatible = "karo,imx6q-tx6q", "fsl,imx6q";
> +
> + aliases {
> + display = &display;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd0_pwr>;
> + enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + power-supply = <®_lcd1_pwr>;
> + /*
> + * a poor man's way to create a 1:1 relationship between
> + * the PWM value and the actual duty cycle
> + */
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100>;
> + default-brightness-level = <50>;
> + };
> +
> + display: display at di0 {
> + compatible = "fsl,imx-parallel-display";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_disp0_2>;
> + interface-pix-fmt = "rgb24";
> + status = "okay";
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + display-timings {
> + native-mode = <&vga>;
> +
> + vga: VGA {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <48>;
> + hsync-len = <96>;
> + hfront-porch = <16>;
> + vback-porch = <31>;
> + vsync-len = <2>;
> + vfront-porch = <12>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETV570 {
> + clock-frequency = <25200000>;
> + hactive = <640>;
> + vactive = <480>;
> + hback-porch = <114>;
> + hsync-len = <30>;
> + hfront-porch = <16>;
> + vback-porch = <32>;
> + vsync-len = <3>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0350 {
> + clock-frequency = <6413760>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <34>;
> + hsync-len = <34>;
> + hfront-porch = <20>;
> + vback-porch = <15>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0430 {
> + clock-frequency = <9009000>;
> + hactive = <480>;
> + vactive = <272>;
> + hback-porch = <2>;
> + hsync-len = <41>;
> + hfront-porch = <2>;
> + vback-porch = <2>;
> + vsync-len = <10>;
> + vfront-porch = <2>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <1>;
> + };
> +
> + ET0500 {
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ET0700 { /* same as ET0500 */
> + clock-frequency = <33264000>;
> + hactive = <800>;
> + vactive = <480>;
> + hback-porch = <88>;
> + hsync-len = <128>;
> + hfront-porch = <40>;
> + vback-porch = <33>;
> + vsync-len = <2>;
> + vfront-porch = <10>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> +
> + ETQ570 {
> + clock-frequency = <6596040>;
> + hactive = <320>;
> + vactive = <240>;
> + hback-porch = <38>;
> + hsync-len = <30>;
> + hfront-porch = <30>;
> + vback-porch = <16>;
> + vsync-len = <3>;
> + vfront-porch = <4>;
> + hsync-active = <0>;
> + vsync-active = <0>;
> + de-active = <1>;
> + pixelclk-active = <0>;
> + };
> + };
> + };
> +};
> +
> +&ds1339 {
> + status = "disabled";
> +};
> +
> +&gpmi {
> + status = "disabled";
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> +
> +&ipu2 {
> + status = "disabled";
> +};
> +
> +®_lcd0_pwr {
> + status = "disabled";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <4>;
> + non-removable;
> + no-1-8-v;
> + fsl,wp-controller;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_usdhc4: usdhc4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
> + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
> + MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
> + >;
> + };
> +};
> --
> 2.1.4
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 21+ messages in thread* [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules
2016-03-31 6:10 ` Shawn Guo
@ 2016-03-31 6:29 ` Lothar Waßmann
2016-03-31 7:47 ` Shawn Guo
0 siblings, 1 reply; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-31 6:29 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Thu, 31 Mar 2016 14:10:23 +0800 Shawn Guo wrote:
> On Tue, Mar 08, 2016 at 09:04:03AM +0100, Lothar Wa?mann wrote:
> > Add support for the following i.MX6 based modules from Ka-Ro
> > electronics GmbH:
> > TX6S-8034:
> > Processor Freescale i.MX 6 Solo, 800MHz
> > RAM 256MiB DDR3 SDRAM
> > ROM 128MiB NAND Flash
> > Power supply Single 3.1V to 5.5V
> > Size 31mm SO-DIMM
> > Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
> >
> > TX6S-8035:
> > Processor Freescale i.MX 6 Solo, 800MHz
> > RAM 512MiB DDR3 SDRAM
> > ROM 4GiB eMMC
> > Power supply Single 3.1V to 5.5V
> > Size 31mm SO-DIMM
> > Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
> >
> > TX6U-8033:
> > Processor Freescale i.MX 6 Dual Lite, 800MHz
> > RAM 1GiB DDR3 SDRAM
> > ROM 4GiB eMMC
> > Power supply Single 3.1V to 5.5V
> > Size 31mm SO-DIMM
> > Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
> >
> > TX6Q-1036:
> > Processor Freescale i.MX 6Quad, 1GHz
> > RAM 1GB DDR3 SDRAM 64-bit
> > ROM 8GiB eMMC
> > Power supply Single 3.1V to 5.5V
> > Size 31mm SO-DIMM
> > Temp. Range Extended Consumer Grade (-20?C to 105?C Tj)
> >
> > Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
> > ---
> > arch/arm/boot/dts/Makefile | 4 +
> > arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 249 ++++++++++++++++++++++++++++
> > arch/arm/boot/dts/imx6dl-tx6s-8035.dts | 246 +++++++++++++++++++++++++++
> > arch/arm/boot/dts/imx6dl-tx6u-8033.dts | 248 +++++++++++++++++++++++++++
> > arch/arm/boot/dts/imx6q-tx6q-1036.dts | 295 +++++++++++++++++++++++++++++++++
> > 5 files changed, 1042 insertions(+)
> > create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts
> > create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8035.dts
> > create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-8033.dts
> > create mode 100644 arch/arm/boot/dts/imx6q-tx6q-1036.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 072294f..71b5cd3 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -320,6 +320,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > imx6dl-sabrelite.dtb \
> > imx6dl-sabresd.dtb \
> > imx6dl-tx6dl-comtft.dtb \
> > + imx6dl-tx6s-8034.dtb \
> > + imx6dl-tx6s-8035.dtb \
> > + imx6dl-tx6u-8033.dtb \
>
> imx6dl-tx6u-8033.dtb should go after imx6dl-tx6u-801x.dtb?
>
Of course. I obviously missed this when dropping the patch to rename
the dtb files which you rejected.
NB: There is no need to quote the full original mail when you have no
further comments on the remaining part. This would save people
from having to scroll through the mail needlessly looking for further
comments.
Lothar Wa?mann
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules
2016-03-31 6:29 ` Lothar Waßmann
@ 2016-03-31 7:47 ` Shawn Guo
0 siblings, 0 replies; 21+ messages in thread
From: Shawn Guo @ 2016-03-31 7:47 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Mar 31, 2016 at 08:29:44AM +0200, Lothar Wa?mann wrote:
> NB: There is no need to quote the full original mail when you have no
> further comments on the remaining part. This would save people
> from having to scroll through the mail needlessly looking for further
> comments.
I generally put my name/signature at the end of my commenting. So
that's where you can stop looking for further comments.
Shawn
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCHv2 8/8] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
` (6 preceding siblings ...)
2016-03-08 8:04 ` [PATCHv2 7/8] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
@ 2016-03-08 8:04 ` Lothar Waßmann
2016-03-31 6:14 ` [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Shawn Guo
2016-03-31 12:33 ` [PATCHv3 0/5] " Lothar Waßmann
9 siblings, 0 replies; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-08 8:04 UTC (permalink / raw)
To: linux-arm-kernel
This baseboard can be used with all TX6 SoMs, but only a certain set
of combinations can be ordered by default. Add support for these
combinations in mainline, so that users can easily adopt their own
combination of SoM and baseboard themselves.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts | 228 +++++++++++++++++++++++
arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts | 289 +++++++++++++++++++++++++++++
3 files changed, 519 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts
create mode 100644 arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 71b5cd3..dc48167 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -325,6 +325,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-tx6u-8033.dtb \
imx6dl-tx6u-801x.dtb \
imx6dl-tx6u-811x.dtb \
+ imx6dl-tx6u-81xx-mb7.dtb \
imx6dl-udoo.dtb \
imx6dl-wandboard.dtb \
imx6dl-wandboard-revb1.dtb \
@@ -365,6 +366,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-tx6q-1020-comtft.dtb \
imx6q-tx6q-1036.dtb \
imx6q-tx6q-1110.dtb \
+ imx6q-tx6q-11x0-mb7.dtb \
imx6q-udoo.dtb \
imx6q-wandboard.dtb \
imx6q-wandboard-revb1.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts b/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts
new file mode 100644
index 0000000..93351ae
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts
@@ -0,0 +1,255 @@
+/*
+ * Copyright 2016 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6U-81xx Module on MB7 baseboard";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &lvds0;
+ lvds0 = &lvds0;
+ lvds1 = &lvds1;
+ };
+
+ backlight0: backlight0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_lcd0_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ backlight1: backlight1 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+};
+
+&can1 {
+ status = "disabled";
+};
+
+&can2 {
+ xceiver-supply = <®_3v3>;
+};
+
+&i2c3 {
+ polytouch1: eeti at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eeti>;
+ interrupts-extended = <&gpio3 22 IRQ_TYPE_EDGE_FALLING>;
+ wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+};
+
+&kpp {
+ status = "disabled"; /* pads partially clash with backlight1 PWM */
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel at 0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds0_timing1>;
+
+ lvds0_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds0_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds0_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+
+ lvds1: lvds-channel at 1 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds1_timing2>;
+
+ lvds1_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds1_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds1_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_eeti: eetigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts b/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts
new file mode 100644
index 0000000..ded0390
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts
@@ -0,0 +1,264 @@
+/*
+ * Copyright 2016 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6Q-1110/-1130 Module on MB7 baseboard";
+ compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+
+ aliases {
+ display = &lvds0;
+ ipu1 = &ipu2;
+ lvds0 = &lvds0;
+ lvds1 = &lvds1;
+ };
+
+ backlight0: backlight0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_lcd0_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ backlight1: backlight1 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+};
+
+&can1 {
+ status = "disabled";
+};
+
+&can2 {
+ xceiver-supply = <®_3v3>;
+};
+
+&i2c3 {
+ polytouch1: eeti at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eeti>;
+ interrupts-extended = <&gpio3 22 IRQ_TYPE_EDGE_FALLING>;
+ wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+};
+
+&ipu2 {
+ status = "disabled";
+};
+
+&kpp {
+ status = "disabled"; /* pads partially clash with backlight1 PWM */
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel at 0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds0_timing1>;
+
+ lvds0_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds0_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds0_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+
+ lvds1: lvds-channel at 1 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds1_timing2>;
+
+ lvds1_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds1_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds1_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_eeti: eetigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
+ >;
+ };
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
` (7 preceding siblings ...)
2016-03-08 8:04 ` [PATCHv2 8/8] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard Lothar Waßmann
@ 2016-03-31 6:14 ` Shawn Guo
2016-03-31 12:33 ` [PATCHv3 0/5] " Lothar Waßmann
9 siblings, 0 replies; 21+ messages in thread
From: Shawn Guo @ 2016-03-31 6:14 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Mar 08, 2016 at 09:03:56AM +0100, Lothar Wa?mann wrote:
> This patch set updates the Ka-Ro electronics i.MX6 based module
> support and adds support for some new modules and a new baseboard.
>
> changes vs. v1:
> - relicense DTS files under GPLv2/X11
> - dropped patches which have been applied already
> - added some cleanup patches
>
> [PATCHv2 1/8] ARM: dts: imx6-tx6: Relicense the Ka-Ro DT files under GPLv2/X11
> [PATCHv2 2/8] ARM: dts: imx6-tx6: cleanup; no functional change
> [PATCHv2 4/8] ARM: dts: imx6-tx6: disable the spi node by default
> [PATCHv2 5/8] ARM: dts: imx6-tx6: remove container node around pinctrl nodes
> [PATCHv2 6/8] ARM: dts: imx6qdl-tx6: add mdio node for ethernet phy
Applied above 5 patches, thanks.
^ permalink raw reply [flat|nested] 21+ messages in thread* [PATCHv3 0/5] ARM: dts: update Ka-Ro i.MX6 module support
2016-03-08 8:03 [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Lothar Waßmann
` (8 preceding siblings ...)
2016-03-31 6:14 ` [PATCHv2 0/8] ARM: dts: update Ka-Ro i.MX6 module support Shawn Guo
@ 2016-03-31 12:33 ` Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 1/5] ARM: dts: imx6-tx6: remove regulator bus Lothar Waßmann
` (5 more replies)
9 siblings, 6 replies; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-31 12:33 UTC (permalink / raw)
To: linux-arm-kernel
This patch set updates the Ka-Ro electronics i.MX6 based module
support and adds support for some new modules and a new baseboard.
changes vs. v1:
- relicense DTS files under GPLv2/X11
- dropped patches which have been applied already
- added some cleanup patches
changes vs. v2:
- dropped patches which have been applied already
- addressed comments from Shawn Guo
- added patch to remove LED pinctrl from hoggrp
- added patch to enable rtscts support on UARTs
[PATCHv3 1/5] ARM: dts: imx6-tx6: remove regulator bus
[PATCHv3 2/5] ARM: dts: imx6-tx6: remove LED pinctrl setting from hoggrp
[PATCHv3 3/5] ARM: dts: imx6-tx6: enable support for rtscts on UARTs
[PATCHv3 4/5] ARM: dts: imx6: add support for more Ka-Ro electronics modules
[PATCHv3 5/5] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard
^ permalink raw reply [flat|nested] 21+ messages in thread* [PATCHv3 1/5] ARM: dts: imx6-tx6: remove regulator bus
2016-03-31 12:33 ` [PATCHv3 0/5] " Lothar Waßmann
@ 2016-03-31 12:33 ` Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 2/5] ARM: dts: imx6-tx6: remove LED pinctrl setting from hoggrp Lothar Waßmann
` (4 subsequent siblings)
5 siblings, 0 replies; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-31 12:33 UTC (permalink / raw)
To: linux-arm-kernel
DT maintainers don't like the 'simple-bus' container around the
regulator nodes. So remove it.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 166 +++++++++++++++++--------------------
1 file changed, 75 insertions(+), 91 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index afc6022..a3e37a7 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -93,104 +93,88 @@
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- reg_3v3_etn: regulator at 0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "3V3_ETN";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_etnphy_power>;
- gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
+ reg_3v3_etn: regulator-3v3-etn {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3_ETN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etnphy_power>;
+ gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
- reg_2v5: regulator at 1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "2V5";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2500000>;
- regulator-always-on;
- };
+ reg_2v5: regulator-2v5 {
+ compatible = "regulator-fixed";
+ regulator-name = "2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
- reg_3v3: regulator at 2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
- reg_can_xcvr: regulator at 3 {
- compatible = "regulator-fixed";
- reg = <3>;
- regulator-name = "CAN XCVR";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_flexcan_xcvr>;
- gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
- enable-active-low;
- };
+ reg_can_xcvr: regulator-can-xcvr {
+ compatible = "regulator-fixed";
+ regulator-name = "CAN XCVR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan_xcvr>;
+ gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
+ enable-active-low;
+ };
- reg_lcd0_pwr: regulator at 4 {
- compatible = "regulator-fixed";
- reg = <4>;
- regulator-name = "LCD0 POWER";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_lcd0_pwr>;
- gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- regulator-always-on;
- };
+ reg_lcd0_pwr: regulator-lcd0-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD0 POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd0_pwr>;
+ gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
- reg_lcd1_pwr: regulator at 5 {
- compatible = "regulator-fixed";
- reg = <5>;
- regulator-name = "LCD1 POWER";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_lcd1_pwr>;
- gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- regulator-always-on;
- };
+ reg_lcd1_pwr: regulator-lcd1-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD1 POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd1_pwr>;
+ gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
- reg_usbh1_vbus: regulator at 6 {
- compatible = "regulator-fixed";
- reg = <6>;
- regulator-name = "usbh1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbh1_vbus>;
- gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
+ reg_usbh1_vbus: regulator-usbh1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_vbus>;
+ gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
- reg_usbotg_vbus: regulator at 7 {
- compatible = "regulator-fixed";
- reg = <7>;
- regulator-name = "usbotg_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg_vbus>;
- gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
+ reg_usbotg_vbus: regulator-usbotg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbotg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_vbus>;
+ gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
};
sound {
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv3 2/5] ARM: dts: imx6-tx6: remove LED pinctrl setting from hoggrp
2016-03-31 12:33 ` [PATCHv3 0/5] " Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 1/5] ARM: dts: imx6-tx6: remove regulator bus Lothar Waßmann
@ 2016-03-31 12:33 ` Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 3/5] ARM: dts: imx6-tx6: enable support for rtscts on UARTs Lothar Waßmann
` (3 subsequent siblings)
5 siblings, 0 replies; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-31 12:33 UTC (permalink / raw)
To: linux-arm-kernel
Move the pinctrl setting for the board LED from the hoggrp node
to a separate node referenced by the LED driver, so that the pin is
free to be used for different purpose when the LED driver is disabled.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index a3e37a7..d96dba2 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -88,6 +88,8 @@
user_led: user {
label = "Heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_user_led>;
gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
@@ -328,7 +330,6 @@
pinctrl_hog: hoggrp {
fsl,pins = <
- MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */
MX6QDL_PAD_SD3_DAT2__GPIO7_IO06 0x1b0b1 /* ETN PHY RESET */
MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b1 /* ETN PHY INT */
MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b1 /* PWR BTN */
@@ -634,6 +635,12 @@
MX6QDL_PAD_SD3_CLK__GPIO7_IO03 0x170b0 /* SD2 CD */
>;
};
+
+ pinctrl_user_led: user-ledgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */
+ >;
+ };
};
&kpp {
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv3 3/5] ARM: dts: imx6-tx6: enable support for rtscts on UARTs
2016-03-31 12:33 ` [PATCHv3 0/5] " Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 1/5] ARM: dts: imx6-tx6: remove regulator bus Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 2/5] ARM: dts: imx6-tx6: remove LED pinctrl setting from hoggrp Lothar Waßmann
@ 2016-03-31 12:33 ` Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 4/5] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
` (2 subsequent siblings)
5 siblings, 0 replies; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-31 12:33 UTC (permalink / raw)
To: linux-arm-kernel
Add missing pinctrl for the RTS/CTS lines to uart1 and set the
fsl,uart-has-rtscts property on all UARTs to enable support for HW
handshake.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx6qdl-tx6.dtsi | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index d96dba2..24101c1 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -684,19 +684,22 @@
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
+ pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_rtscts>;
+ fsl,uart-has-rtscts;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2 &pinctrl_uart2_rtscts>;
+ fsl,uart-has-rtscts;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3 &pinctrl_uart3_rtscts>;
+ fsl,uart-has-rtscts;
status = "okay";
};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv3 4/5] ARM: dts: imx6: add support for more Ka-Ro electronics modules
2016-03-31 12:33 ` [PATCHv3 0/5] " Lothar Waßmann
` (2 preceding siblings ...)
2016-03-31 12:33 ` [PATCHv3 3/5] ARM: dts: imx6-tx6: enable support for rtscts on UARTs Lothar Waßmann
@ 2016-03-31 12:33 ` Lothar Waßmann
2016-03-31 12:33 ` [PATCHv3 5/5] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard Lothar Waßmann
2016-04-11 13:57 ` [PATCHv3 0/5] ARM: dts: update Ka-Ro i.MX6 module support Shawn Guo
5 siblings, 0 replies; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-31 12:33 UTC (permalink / raw)
To: linux-arm-kernel
Add support for the following i.MX6 based modules from Ka-Ro
electronics GmbH:
TX6S-8034:
Processor Freescale i.MX 6 Solo, 800MHz
RAM 256MiB DDR3 SDRAM
ROM 128MiB NAND Flash
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
TX6S-8035:
Processor Freescale i.MX 6 Solo, 800MHz
RAM 512MiB DDR3 SDRAM
ROM 4GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
TX6U-8033:
Processor Freescale i.MX 6 Dual Lite, 800MHz
RAM 1GiB DDR3 SDRAM
ROM 4GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range industrial grade (-40?C/-25?C to 105?C Tj)
TX6Q-1036:
Processor Freescale i.MX 6Quad, 1GHz
RAM 1GB DDR3 SDRAM 64-bit
ROM 8GiB eMMC
Power supply Single 3.1V to 5.5V
Size 31mm SO-DIMM
Temp. Range Extended Consumer Grade (-20?C to 105?C Tj)
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 4 +
arch/arm/boot/dts/imx6dl-tx6s-8034.dts | 237 ++++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6dl-tx6s-8035.dts | 253 +++++++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6dl-tx6u-8033.dts | 248 ++++++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6q-tx6q-1036.dts | 252 ++++++++++++++++++++++++++++++++
5 files changed, 994 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8034.dts
create mode 100644 arch/arm/boot/dts/imx6dl-tx6s-8035.dts
create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-8033.dts
create mode 100644 arch/arm/boot/dts/imx6q-tx6q-1036.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 1993333..c9550c7 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -322,7 +322,10 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \
imx6dl-tx6dl-comtft.dtb \
+ imx6dl-tx6s-8034.dtb \
+ imx6dl-tx6s-8035.dtb \
imx6dl-tx6u-801x.dtb \
+ imx6dl-tx6u-8033.dtb \
imx6dl-tx6u-811x.dtb \
imx6dl-udoo.dtb \
imx6dl-wandboard.dtb \
@@ -362,6 +365,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-tx6q-1010-comtft.dtb \
imx6q-tx6q-1020.dtb \
imx6q-tx6q-1020-comtft.dtb \
+ imx6q-tx6q-1036.dtb \
imx6q-tx6q-1110.dtb \
imx6q-udoo.dtb \
imx6q-wandboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
new file mode 100644
index 0000000..ff8f7b1
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
@@ -0,0 +1,237 @@
+/*
+ * Copyright 2015-2016 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6S-8034 Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &display;
+ ipu1 = &ipu1;
+ };
+
+ cpus {
+ /delete-node/ cpu at 1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd0_pwr>;
+ enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_2>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ native-mode = <&vga>;
+
+ vga: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&pinctrl_usdhc1 {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x070b1
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x070b1
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x070b1
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x070b1
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x070b1
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x070b1
+ MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x170b0 /* SD1 CD */
+ >;
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+®_lcd0_pwr {
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8035.dts b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
new file mode 100644
index 0000000..f988950
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
@@ -0,0 +1,253 @@
+/*
+ * Copyright 2015-2016 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6S-8035 Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &display;
+ ipu1 = &ipu1;
+ };
+
+ cpus {
+ /delete-node/ cpu at 1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd0_pwr>;
+ enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_2>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ native-mode = <&vga>;
+
+ vga: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+®_lcd0_pwr {
+ status = "disabled";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <4>;
+ non-removable;
+ no-1-8-v;
+ fsl,wp-controller;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
+ MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-8033.dts b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
new file mode 100644
index 0000000..4d3204a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
@@ -0,0 +1,248 @@
+/*
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6U-8033 Module";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &display;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd0_pwr>;
+ enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_2>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ native-mode = <&vga>;
+
+ vga: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+®_lcd0_pwr {
+ status = "disabled";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <4>;
+ non-removable;
+ no-1-8-v;
+ fsl,wp-controller;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
+ MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1036.dts b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
new file mode 100644
index 0000000..7c152e3
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
@@ -0,0 +1,252 @@
+/*
+ * Copyright 2014-2016 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6Q-1036 Module";
+ compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+
+ aliases {
+ display = &display;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd0_pwr>;
+ enable-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ display: display at di0 {
+ compatible = "fsl,imx-parallel-display";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_2>;
+ interface-pix-fmt = "rgb24";
+ status = "okay";
+
+ port {
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ display-timings {
+ native-mode = <&vga>;
+
+ vga: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+&ipu2 {
+ status = "disabled";
+};
+
+®_lcd0_pwr {
+ status = "disabled";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <4>;
+ non-removable;
+ no-1-8-v;
+ fsl,wp-controller;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x070b1
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x070b1
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x070b1
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x070b1
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x070b1
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x070b1
+ MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x0b0b1
+ >;
+ };
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv3 5/5] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard
2016-03-31 12:33 ` [PATCHv3 0/5] " Lothar Waßmann
` (3 preceding siblings ...)
2016-03-31 12:33 ` [PATCHv3 4/5] ARM: dts: imx6: add support for more Ka-Ro electronics modules Lothar Waßmann
@ 2016-03-31 12:33 ` Lothar Waßmann
2016-04-11 13:57 ` [PATCHv3 0/5] ARM: dts: update Ka-Ro i.MX6 module support Shawn Guo
5 siblings, 0 replies; 21+ messages in thread
From: Lothar Waßmann @ 2016-03-31 12:33 UTC (permalink / raw)
To: linux-arm-kernel
This baseboard can be used with all TX6 SoMs, but only a certain set
of combinations can be ordered by default. Add support for these
combinations in mainline, so that users can easily adopt their own
combination of SoM and baseboard themselves.
Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts | 255 ++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts | 264 +++++++++++++++++++++++++++++
3 files changed, 521 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts
create mode 100644 arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index c9550c7..08f8afe 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -327,6 +327,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-tx6u-801x.dtb \
imx6dl-tx6u-8033.dtb \
imx6dl-tx6u-811x.dtb \
+ imx6dl-tx6u-81xx-mb7.dtb \
imx6dl-udoo.dtb \
imx6dl-wandboard.dtb \
imx6dl-wandboard-revb1.dtb \
@@ -367,6 +368,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-tx6q-1020-comtft.dtb \
imx6q-tx6q-1036.dtb \
imx6q-tx6q-1110.dtb \
+ imx6q-tx6q-11x0-mb7.dtb \
imx6q-udoo.dtb \
imx6q-wandboard.dtb \
imx6q-wandboard-revb1.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts b/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts
new file mode 100644
index 0000000..b9a783f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts
@@ -0,0 +1,255 @@
+/*
+ * Copyright 2016 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6U-81xx Module on MB7 baseboard";
+ compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+ aliases {
+ display = &lvds0;
+ lvds0 = &lvds0;
+ lvds1 = &lvds1;
+ };
+
+ backlight0: backlight0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_lcd0_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ backlight1: backlight1 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+};
+
+&can1 {
+ status = "disabled";
+};
+
+&can2 {
+ xceiver-supply = <®_3v3>;
+};
+
+&i2c3 {
+ polytouch1: eeti at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eeti>;
+ interrupts-extended = <&gpio3 22 IRQ_TYPE_EDGE_FALLING>;
+ wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+};
+
+&kpp {
+ status = "disabled"; /* pads partially clash with backlight1 PWM */
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel at 0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds0_timing1>;
+
+ lvds0_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds0_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds0_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+
+ lvds1: lvds-channel at 1 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds1_timing2>;
+
+ lvds1_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds1_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds1_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_eeti: eetigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts b/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts
new file mode 100644
index 0000000..d78b129
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts
@@ -0,0 +1,264 @@
+/*
+ * Copyright 2016 Lothar Wa?mann <LW@KARO-electronics.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TX6Q-1110/-1130 Module on MB7 baseboard";
+ compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+
+ aliases {
+ display = &lvds0;
+ ipu1 = &ipu2;
+ lvds0 = &lvds0;
+ lvds1 = &lvds1;
+ };
+
+ backlight0: backlight0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_lcd0_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ backlight1: backlight1 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <®_lcd1_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+};
+
+&can1 {
+ status = "disabled";
+};
+
+&can2 {
+ xceiver-supply = <®_3v3>;
+};
+
+&i2c3 {
+ polytouch1: eeti at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eeti>;
+ interrupts-extended = <&gpio3 22 IRQ_TYPE_EDGE_FALLING>;
+ wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+};
+
+&ipu2 {
+ status = "disabled";
+};
+
+&kpp {
+ status = "disabled"; /* pads partially clash with backlight1 PWM */
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel at 0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds0_timing1>;
+
+ lvds0_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds0_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds0_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+
+ lvds1: lvds-channel at 1 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ display-timings {
+ native-mode = <&lvds1_timing2>;
+
+ lvds1_timing0: hsd100pxn1 {
+ clock-frequency = <65000000>;
+ hactive = <1024>;
+ vactive = <768>;
+ hback-porch = <220>;
+ hfront-porch = <40>;
+ vback-porch = <21>;
+ vfront-porch = <7>;
+ hsync-len = <60>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ lvds1_timing1: VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vfront-porch = <12>;
+ hsync-len = <96>;
+ vsync-len = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ lvds1_timing2: nl12880bc20 {
+ clock-frequency = <71000000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hback-porch = <50>;
+ hfront-porch = <50>;
+ vback-porch = <5>;
+ vfront-porch = <5>;
+ hsync-len = <60>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_eeti: eetigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b1 /* Interrupt */
+ >;
+ };
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 21+ messages in thread* [PATCHv3 0/5] ARM: dts: update Ka-Ro i.MX6 module support
2016-03-31 12:33 ` [PATCHv3 0/5] " Lothar Waßmann
` (4 preceding siblings ...)
2016-03-31 12:33 ` [PATCHv3 5/5] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard Lothar Waßmann
@ 2016-04-11 13:57 ` Shawn Guo
5 siblings, 0 replies; 21+ messages in thread
From: Shawn Guo @ 2016-04-11 13:57 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Mar 31, 2016 at 02:33:40PM +0200, Lothar Wa?mann wrote:
> This patch set updates the Ka-Ro electronics i.MX6 based module
> support and adds support for some new modules and a new baseboard.
>
> changes vs. v1:
> - relicense DTS files under GPLv2/X11
> - dropped patches which have been applied already
> - added some cleanup patches
>
> changes vs. v2:
> - dropped patches which have been applied already
> - addressed comments from Shawn Guo
> - added patch to remove LED pinctrl from hoggrp
> - added patch to enable rtscts support on UARTs
>
> [PATCHv3 1/5] ARM: dts: imx6-tx6: remove regulator bus
> [PATCHv3 2/5] ARM: dts: imx6-tx6: remove LED pinctrl setting from hoggrp
> [PATCHv3 3/5] ARM: dts: imx6-tx6: enable support for rtscts on UARTs
> [PATCHv3 4/5] ARM: dts: imx6: add support for more Ka-Ro electronics modules
> [PATCHv3 5/5] ARM: dts: imx6: add support for the Ka-Ro electronics 'MB7' baseboard
Applied all, thanks.
^ permalink raw reply [flat|nested] 21+ messages in thread