* [PATCH v2 1/2] ARM: dts: am335x: Add initial support for ICEv2 board
2016-03-23 3:34 [PATCH v2 0/2] ARM: am335x: Add support for ICEv2 board Lokesh Vutla
@ 2016-03-23 3:34 ` Lokesh Vutla
2016-03-23 9:46 ` Grygorii Strashko
2016-03-23 3:34 ` [PATCH v2 2/2] ARM: omap2plus_defconfig: Enable GPIO_TPIC2810 Lokesh Vutla
1 sibling, 1 reply; 6+ messages in thread
From: Lokesh Vutla @ 2016-03-23 3:34 UTC (permalink / raw)
To: linux-arm-kernel
TI's Industrial Communication Engine EVM is a low cost hardware mainly
developed for industrial communication type applications using serial
or Ethernet based interfaces. This platform features TI's AM3359 with
800MHz single core Cortex-A8 processor, 256MB DDR3, 64MB SPI flash,
8MB NOR Flash, mmc, usb, can, dual Ethernet ports.
For more information, look at HW user guide[1], Data manual[2].
Just add basic support for the moment.
[1] http://processors.wiki.ti.com/index.php/AM335x_Industrial_Communication_Engine_EVM_Rev2_1_HW_User_Guide
[2] http://www.ti.com/lit/ds/symlink/am3359.pdf
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
Changes since v1:
- Add separate nodes for gpio leds and tpic2810 leds.
.../devicetree/bindings/arm/omap/omap.txt | 3 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am335x-icev2.dts | 306 +++++++++++++++++++++
3 files changed, 310 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-icev2.dts
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 21e71a5..20f6d71 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -133,6 +133,9 @@ Boards:
- AM335X Bone : Low cost community board
compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3"
+- AM3359 ICEv2 : Low cost Industrial Communication Engine EVM.
+ compatible = "ti,am3359-icev2", "ti,am33xx", "ti,omap3"
+
- AM335X OrionLXm : Substation Automation Platform
compatible = "novatech,am335x-lxm", "ti,am33xx"
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 52b34a0..7dcf55e 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -486,6 +486,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
am335x-cm-t335.dtb \
am335x-evm.dtb \
am335x-evmsk.dtb \
+ am335x-icev2.dtb \
am335x-lxm.dtb \
am335x-nano.dtb \
am335x-pepper.dtb \
diff --git a/arch/arm/boot/dts/am335x-icev2.dts b/arch/arm/boot/dts/am335x-icev2.dts
new file mode 100644
index 0000000..e271013
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-icev2.dts
@@ -0,0 +1,306 @@
+/*
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * AM335x ICE V2 board
+ * http://www.ti.com/tool/tmdsice3359
+ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+ model = "TI AM3359 ICE-V2";
+ compatible = "ti,am3359-icev2", "ti,am33xx";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ vbat: fixedregulator at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ };
+
+ vtt_fixed: fixedregulator at 1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vtt";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ gpio = <&gpio0 18 GPIO_ACTIVE_HIGH>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ };
+
+ leds at 0 {
+ compatible = "gpio-leds";
+
+ led at 0 {
+ label = "out0";
+ gpios = <&tpic2810 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led at 1 {
+ label = "out1";
+ gpios = <&tpic2810 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led at 2 {
+ label = "out2";
+ gpios = <&tpic2810 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led at 3 {
+ label = "out3";
+ gpios = <&tpic2810 3 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led at 4 {
+ label = "out4";
+ gpios = <&tpic2810 4 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led at 5 {
+ label = "out5";
+ gpios = <&tpic2810 5 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led at 6 {
+ label = "out6";
+ gpios = <&tpic2810 6 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led at 7 {
+ label = "out7";
+ gpios = <&tpic2810 7 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ /* Tricolor status LEDs */
+ leds at 1 {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_leds>;
+
+ led at 0 {
+ label = "status0:red:cpu0";
+ gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "cpu0";
+ };
+
+ led at 1 {
+ label = "status0:green:usr";
+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led at 2 {
+ label = "status0:yellow:usr";
+ gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led at 3 {
+ label = "status1:red:mmc0";
+ gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "mmc0";
+ };
+
+ led at 4 {
+ label = "status1:green:usr";
+ gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led at 5 {
+ label = "status1:yellow:usr";
+ gpios = <&gpio0 19 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+};
+
+&am33xx_pinmux {
+ user_leds: user_leds {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x91c, PIN_OUTPUT | MUX_MODE7) /* (J18) gmii1_txd3.gpio0[16] */
+ AM33XX_IOPAD(0x920, PIN_OUTPUT | MUX_MODE7) /* (K15) gmii1_txd2.gpio0[17] */
+ AM33XX_IOPAD(0x9b0, PIN_OUTPUT | MUX_MODE7) /* (A15) xdma_event_intr0.gpio0[19] */
+ AM33XX_IOPAD(0x9b4, PIN_OUTPUT | MUX_MODE7) /* (D14) xdma_event_intr1.gpio0[20] */
+ AM33XX_IOPAD(0x880, PIN_OUTPUT | MUX_MODE7) /* (U9) gpmc_csn1.gpio1[30] */
+ AM33XX_IOPAD(0x92c, PIN_OUTPUT | MUX_MODE7) /* (K18) gmii1_txclk.gpio3[9] */
+ >;
+ };
+
+ mmc0_pins_default: mmc0_pins_default {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* (F17) mmc0_dat3.mmc0_dat3 */
+ AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* (F18) mmc0_dat2.mmc0_dat2 */
+ AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* (G15) mmc0_dat1.mmc0_dat1 */
+ AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* (G16) mmc0_dat0.mmc0_dat0 */
+ AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* (G17) mmc0_clk.mmc0_clk */
+ AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* (G18) mmc0_cmd.mmc0_cmd */
+ AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE5) /* (C15) spi0_cs1.mmc0_sdcd */
+ >;
+ };
+
+ i2c0_pins_default: i2c0_pins_default {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x988, PIN_INPUT | MUX_MODE0) /* (C17) I2C0_SDA.I2C0_SDA */
+ AM33XX_IOPAD(0x98c, PIN_INPUT | MUX_MODE0) /* (C16) I2C0_SCL.I2C0_SCL */
+ >;
+ };
+
+ spi0_pins_default: spi0_pins_default {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x950, PIN_INPUT_PULLUP | MUX_MODE0) /* (A17) spi0_sclk.spi0_sclk */
+ AM33XX_IOPAD(0x954, PIN_INPUT_PULLUP | MUX_MODE0) /* (B17) spi0_d0.spi0_d0 */
+ AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0) /* (B16) spi0_d1.spi0_d1 */
+ AM33XX_IOPAD(0x95c, PIN_INPUT_PULLUP | MUX_MODE0) /* (A16) spi0_cs0.spi0_cs0 */
+ >;
+ };
+
+ uart3_pins_default: uart3_pins_default {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1) /* (L17) gmii1_rxd3.uart3_rxd */
+ AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLUP | MUX_MODE1) /* (L16) gmii1_rxd2.uart3_txd */
+ >;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_default>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: power-controller at 2d {
+ reg = <0x2d>;
+ };
+
+ tpic2810: gpio at 60 {
+ compatible = "ti,tpic2810";
+ reg = <0x60>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+#include "tps65910.dtsi"
+
+&tps {
+ vcc1-supply = <&vbat>;
+ vcc2-supply = <&vbat>;
+ vcc3-supply = <&vbat>;
+ vcc4-supply = <&vbat>;
+ vcc5-supply = <&vbat>;
+ vcc6-supply = <&vbat>;
+ vcc7-supply = <&vbat>;
+ vccio-supply = <&vbat>;
+
+ regulators {
+ vrtc_reg: regulator at 0 {
+ regulator-always-on;
+ };
+
+ vio_reg: regulator at 1 {
+ regulator-always-on;
+ };
+
+ vdd1_reg: regulator at 2 {
+ regulator-name = "vdd_mpu";
+ regulator-min-microvolt = <912500>;
+ regulator-max-microvolt = <1326000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd2_reg: regulator at 3 {
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <912500>;
+ regulator-max-microvolt = <1144000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdd3_reg: regulator at 4 {
+ regulator-always-on;
+ };
+
+ vdig1_reg: regulator at 5 {
+ regulator-always-on;
+ };
+
+ vdig2_reg: regulator at 6 {
+ regulator-always-on;
+ };
+
+ vpll_reg: regulator at 7 {
+ regulator-always-on;
+ };
+
+ vdac_reg: regulator at 8 {
+ regulator-always-on;
+ };
+
+ vaux1_reg: regulator at 9 {
+ regulator-always-on;
+ };
+
+ vaux2_reg: regulator at 10 {
+ regulator-always-on;
+ };
+
+ vaux33_reg: regulator at 11 {
+ regulator-always-on;
+ };
+
+ vmmc_reg: regulator at 12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&vmmc_reg>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_default>;
+};
+
+&gpio0 {
+ /* Do not idle the GPIO used for holding the VTT regulator */
+ ti,no-reset-on-init;
+ ti,no-idle-on-init;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins_default>;
+ status = "okay";
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 6+ messages in thread