[PATCH V17 1/3] dmaengine: qcom_hidma: implement lower level hardware interface

[vinod.koul@intel.com (Vinod Koul)]

On Mon, Apr 11, 2016 at 10:21:11AM -0400, Sinan Kaya wrote:

> + * HIDMA is not aware of IOMMU presence since it follows the DMA API. All
> + * IOMMU latency will be built into the data movement time. By the time
> + * interrupt happens, IOMMU lookups + data movement has already taken place.

Do you mean dmaengine API or dma mapping API here? Where is you IOMMU
located wrt to dma controller?

> + *
> + * While the first read in a typical PCI endpoint ISR flushes all outstanding
> + * requests traditionally to the destination, this concept does not apply
> + * here for this HW.
> + */
> +static void hidma_ll_int_handler_internal(struct hidma_lldev *lldev)
> +{
> +	u32 status;
> +	u32 enable;
> +	u32 cause;
> +
> +	/*
> +	 * Fine tuned for this HW...
> +	 *
> +	 * This ISR has been designed for this particular hardware. Relaxed
> +	 * read and write accessors are used for performance reasons due to
> +	 * interrupt delivery guarantees. Do not copy this code blindly and
> +	 * expect that to work.
> +	 */
> +	status = readl_relaxed(lldev->evca + HIDMA_EVCA_IRQ_STAT_REG);
> +	enable = readl_relaxed(lldev->evca + HIDMA_EVCA_IRQ_EN_REG);
> +	cause = status & enable;
> +
> +	while (cause) {
> +		if ((cause & BIT(HIDMA_IRQ_TR_CH_INVALID_TRE_BIT_POS)) ||
> +		    (cause & BIT(HIDMA_IRQ_TR_CH_TRE_RD_RSP_ER_BIT_POS)) ||
> +		    (cause & BIT(HIDMA_IRQ_EV_CH_WR_RESP_BIT_POS)) ||
> +		    (cause & BIT(HIDMA_IRQ_TR_CH_DATA_RD_ER_BIT_POS)) ||
> +		    (cause & BIT(HIDMA_IRQ_TR_CH_DATA_WR_ER_BIT_POS))) {

Switch please

> +			u8 err_code = HIDMA_EVRE_STATUS_ERROR;
> +			u8 err_info = 0xFF;
> +
> +			/* Clear out pending interrupts */
> +			writel(cause, lldev->evca + HIDMA_EVCA_IRQ_CLR_REG);
> +
> +			dev_err(lldev->dev, "error 0x%x, resetting...\n",
> +				cause);
> +
> +			hidma_cleanup_pending_tre(lldev, err_info, err_code);
> +
> +			/* reset the channel for recovery */
> +			if (hidma_ll_setup(lldev)) {

should this be done in ISR?

> +int hidma_ll_resume(struct hidma_lldev *lldev)
> +{
> +	return hidma_ll_enable(lldev);
> +}

why do we need this empty function, use hidma_ll_enable.

> +bool hidma_ll_isenabled(struct hidma_lldev *lldev)
> +{
> +	u32 val;
> +
> +	val = readl(lldev->trca + HIDMA_TRCA_CTRLSTS_REG);
> +	lldev->trch_state = HIDMA_CH_STATE(val);
> +	val = readl(lldev->evca + HIDMA_EVCA_CTRLSTS_REG);
> +	lldev->evch_state = HIDMA_CH_STATE(val);
> +
> +	/* both channels have to be enabled before calling this function */
> +	if (((lldev->trch_state == HIDMA_CH_ENABLED) ||
> +	     (lldev->trch_state == HIDMA_CH_RUNNING)) &&
> +	    ((lldev->evch_state == HIDMA_CH_ENABLED) ||
> +	     (lldev->evch_state == HIDMA_CH_RUNNING)))
> +		return true;

hmmm this looks hard to read, why not do:

is_chan_enabled(state)
{
	switch (state) {
	case HIDMA_CH_ENABLED:
	case HIDMA_CH_RUNNING:
		return true;
	default:
		return false;
}

and then :

	if (is_chan_enabled(lldev->trch_state) &&
			is_chan_enabled(lldev->evch_state))


> +void hidma_ll_start(struct hidma_lldev *lldev)
> +{
> +	hidma_ll_hw_start(lldev);
> +}

Another dummy :(

> +/*
> + * Note that even though we stop this channel
> + * if there is a pending transaction in flight
> + * it will complete and follow the callback.
> + * This request will prevent further requests
> + * to be made.

Why the odd formating?

> +int hidma_ll_uninit(struct hidma_lldev *lldev)
> +{
> +	int rc = 0;
> +	u32 val;
> +
> +	if (!lldev)
> +		return -ENODEV;
> +
> +	if (lldev->initialized) {
> +		u32 required_bytes;
> +
> +		lldev->initialized = 0;
> +
> +		required_bytes = sizeof(struct hidma_tre) * lldev->nr_tres;
> +		tasklet_kill(&lldev->task);
> +		memset(lldev->trepool, 0, required_bytes);
> +		lldev->trepool = NULL;
> +		lldev->pending_tre_count = 0;
> +		lldev->tre_write_offset = 0;
> +
> +		rc = hidma_ll_reset(lldev);
> +
> +		/*
> +		 * Clear all pending interrupts again.
> +		 * Otherwise, we observe reset complete interrupts.
> +		 */
> +		val = readl(lldev->evca + HIDMA_EVCA_IRQ_STAT_REG);
> +		writel(val, lldev->evca + HIDMA_EVCA_IRQ_CLR_REG);
> +		hidma_ll_enable_irq(lldev, 0);

uninit enables irq?

-- 
~Vinod