[PATCH v5 05/11] thermal: qcom: tsens-8960: Add support for 8960 family of SoCs

[edubezval@gmail.com (Eduardo Valentin)]

On Thu, Apr 14, 2016 at 03:01:53PM +0530, Rajendra Nayak wrote:
> 8960 family of SoCs have the TSENS device as part of GCC, hence
> the driver probes the virtual child device created by GCC and
> uses the parent to extract all DT properties and reuses the GCC
> regmap.
> 
> Also GCC/TSENS are part of a  domain thats not always ON.
> Hence add .suspend and .resume hooks to save and restore some of
> the inited register context.
> 
> Also 8960 family have some of the TSENS init sequence thats
> required to be done by the HLOS driver (some later versions of TSENS
> do not export these registers to non-secure world, and hence need
> these initializations to be done by secure bootloaders)
> 
> 8660 from the same family has just one sensor and hence some register
> offset/layout differences which need special handling in the driver.
> 
> Based on the original code from Siddartha Mohanadoss, Stephen Boyd and
> Narendran Rajan.
> 
> Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
> ---
>  drivers/thermal/qcom/Makefile     |   2 +-
>  drivers/thermal/qcom/tsens-8960.c | 293 ++++++++++++++++++++++++++++++++++++++
>  drivers/thermal/qcom/tsens.c      |   8 +-
>  drivers/thermal/qcom/tsens.h      |   2 +-
>  4 files changed, 299 insertions(+), 6 deletions(-)
>  create mode 100644 drivers/thermal/qcom/tsens-8960.c
> 
> diff --git a/drivers/thermal/qcom/Makefile b/drivers/thermal/qcom/Makefile
> index a471100..f3cefd1 100644
> --- a/drivers/thermal/qcom/Makefile
> +++ b/drivers/thermal/qcom/Makefile
> @@ -1,2 +1,2 @@
>  obj-$(CONFIG_QCOM_TSENS)	+= qcom_tsens.o
> -qcom_tsens-y			+= tsens.o tsens-common.o tsens-8916.o tsens-8974.o
> +qcom_tsens-y			+= tsens.o tsens-common.o tsens-8916.o tsens-8974.o tsens-8960.o
> diff --git a/drivers/thermal/qcom/tsens-8960.c b/drivers/thermal/qcom/tsens-8960.c
> new file mode 100644
> index 0000000..a5976ec3
> --- /dev/null
> +++ b/drivers/thermal/qcom/tsens-8960.c
> @@ -0,0 +1,293 @@
> +/*
> + * Copyright (c) 2015, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <linux/platform_device.h>
> +#include <linux/delay.h>
> +#include <linux/bitops.h>
> +#include <linux/regmap.h>
> +#include <linux/thermal.h>
> +#include "tsens.h"
> +
> +#define CAL_MDEGC		30000
> +
> +#define CONFIG_ADDR		0x3640
> +#define CONFIG_ADDR_8660	0x3620
> +/* CONFIG_ADDR bitmasks */
> +#define CONFIG			0x9b
> +#define CONFIG_MASK		0xf
> +#define CONFIG_8660		1
> +#define CONFIG_SHIFT_8660	28
> +#define CONFIG_MASK_8660	(3 << CONFIG_SHIFT_8660)
> +
> +#define STATUS_CNTL_ADDR_8064	0x3660
> +#define CNTL_ADDR		0x3620
> +/* CNTL_ADDR bitmasks */
> +#define EN			BIT(0)
> +#define SW_RST			BIT(1)
> +#define SENSOR0_EN		BIT(3)
> +#define SLP_CLK_ENA		BIT(26)
> +#define SLP_CLK_ENA_8660	BIT(24)
> +#define MEASURE_PERIOD		1
> +#define SENSOR0_SHIFT		3
> +
> +/* INT_STATUS_ADDR bitmasks */
> +#define MIN_STATUS_MASK		BIT(0)
> +#define LOWER_STATUS_CLR	BIT(1)
> +#define UPPER_STATUS_CLR	BIT(2)
> +#define MAX_STATUS_MASK		BIT(3)
> +
> +#define THRESHOLD_ADDR		0x3624
> +/* THRESHOLD_ADDR bitmasks */
> +#define THRESHOLD_MAX_LIMIT_SHIFT	24
> +#define THRESHOLD_MIN_LIMIT_SHIFT	16
> +#define THRESHOLD_UPPER_LIMIT_SHIFT	8
> +#define THRESHOLD_LOWER_LIMIT_SHIFT	0
> +
> +/* Initial temperature threshold values */
> +#define LOWER_LIMIT_TH		0x50
> +#define UPPER_LIMIT_TH		0xdf
> +#define MIN_LIMIT_TH		0x0
> +#define MAX_LIMIT_TH		0xff
> +
> +#define S0_STATUS_ADDR		0x3628
> +#define INT_STATUS_ADDR		0x363c
> +#define TRDY_MASK		BIT(7)
> +#define TIMEOUT_US		100
> +
> +static int suspend_8960(struct tsens_device *tmdev)
> +{
> +	int ret;
> +	unsigned int mask;
> +	struct regmap *map = tmdev->map;
> +
> +	ret = regmap_read(map, THRESHOLD_ADDR, &tmdev->ctx.threshold);
> +	if (ret)
> +		return ret;
> +
> +	ret = regmap_read(map, CNTL_ADDR, &tmdev->ctx.control);
> +	if (ret)
> +		return ret;
> +
> +	if (tmdev->num_sensors > 1)
> +		mask = SLP_CLK_ENA | EN;
> +	else
> +		mask = SLP_CLK_ENA_8660 | EN;
> +
> +	ret = regmap_update_bits(map, CNTL_ADDR, mask, 0);
> +	if (ret)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static int resume_8960(struct tsens_device *tmdev)
> +{
> +	int ret;
> +	struct regmap *map = tmdev->map;
> +
> +	ret = regmap_update_bits(map, CNTL_ADDR, SW_RST, SW_RST);
> +	if (ret)
> +		return ret;
> +
> +	/*
> +	 * Separate CONFIG restore is not needed only for 8660 as
> +	 * config is part of CTRL Addr and its restored as such
> +	 */
> +	if (tmdev->num_sensors > 1) {
> +		ret = regmap_update_bits(map, CONFIG_ADDR, CONFIG_MASK, CONFIG);
> +		if (ret)
> +			return ret;
> +	}
> +
> +	ret = regmap_write(map, THRESHOLD_ADDR, tmdev->ctx.threshold);
> +	if (ret)
> +		return ret;
> +
> +	ret = regmap_write(map, CNTL_ADDR, tmdev->ctx.control);
> +	if (ret)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static int enable_8960(struct tsens_device *tmdev, int id)
> +{
> +	int ret;
> +	u32 reg, mask;
> +
> +	ret = regmap_read(tmdev->map, CNTL_ADDR, &reg);
> +	if (ret)
> +		return ret;
> +
> +	mask = BIT(id + SENSOR0_SHIFT);
> +	ret = regmap_write(tmdev->map, CNTL_ADDR, reg | SW_RST);
> +	if (ret)
> +		return ret;
> +
> +	if (tmdev->num_sensors > 1)
> +		reg |= mask | SLP_CLK_ENA | EN;
> +	else
> +		reg |= mask | SLP_CLK_ENA_8660 | EN;
> +
> +	ret = regmap_write(tmdev->map, CNTL_ADDR, reg);
> +	if (ret)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static void disable_8960(struct tsens_device *tmdev)
> +{
> +	int ret;
> +	u32 reg_cntl;
> +	u32 mask;
> +
> +	mask = GENMASK(tmdev->num_sensors - 1, 0);
> +	mask <<= SENSOR0_SHIFT;
> +	mask |= EN;
> +
> +	ret = regmap_read(tmdev->map, CNTL_ADDR, &reg_cntl);
> +	if (ret)
> +		return;
> +
> +	reg_cntl &= ~mask;
> +
> +	if (tmdev->num_sensors > 1)
> +		reg_cntl &= ~SLP_CLK_ENA;
> +	else
> +		reg_cntl &= ~SLP_CLK_ENA_8660;
> +
> +	regmap_write(tmdev->map, CNTL_ADDR, reg_cntl);
> +}
> +
> +static int init_8960(struct tsens_device *tmdev)
> +{
> +	int ret, i;
> +	u32 reg_cntl;
> +
> +	tmdev->map = dev_get_regmap(tmdev->dev, NULL);
> +	if (!tmdev->map)
> +		return -ENODEV;
> +
> +	/*
> +	 * The status registers for each sensor are discontiguous
> +	 * because some SoCs have 5 sensors while others have more
> +	 * but the control registers stay in the same place, i.e
> +	 * directly after the first 5 status registers.
> +	 */
> +	for (i = 0; i < tmdev->num_sensors; i++) {
> +		if (i >= 5)
> +			tmdev->sensor[i].status = S0_STATUS_ADDR + 40;
> +		tmdev->sensor[i].status += i * 4;
> +	}
> +
> +	reg_cntl = SW_RST;
> +	ret = regmap_update_bits(tmdev->map, CNTL_ADDR, SW_RST, reg_cntl);
> +	if (ret)
> +		return ret;
> +
> +	if (tmdev->num_sensors > 1) {
> +		reg_cntl |= SLP_CLK_ENA | (MEASURE_PERIOD << 18);
> +		reg_cntl &= ~SW_RST;
> +		ret = regmap_update_bits(tmdev->map, CONFIG_ADDR,
> +					 CONFIG_MASK, CONFIG);
> +	} else {
> +		reg_cntl |= SLP_CLK_ENA_8660 | (MEASURE_PERIOD << 16);
> +		reg_cntl &= ~CONFIG_MASK_8660;
> +		reg_cntl |= CONFIG_8660 << CONFIG_SHIFT_8660;
> +	}
> +
> +	reg_cntl |= GENMASK(tmdev->num_sensors - 1, 0) << SENSOR0_SHIFT;
> +	ret = regmap_write(tmdev->map, CNTL_ADDR, reg_cntl);
> +	if (ret)
> +		return ret;
> +
> +	reg_cntl |= EN;
> +	ret = regmap_write(tmdev->map, CNTL_ADDR, reg_cntl);
> +	if (ret)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static int calibrate_8960(struct tsens_device *tmdev)
> +{
> +	int i;
> +	char *data;
> +
> +	ssize_t num_read = tmdev->num_sensors;
> +	struct tsens_sensor *s = tmdev->sensor;
> +
> +	data = qfprom_read(tmdev->dev, "calib");
> +	if (IS_ERR(data))
> +		data = qfprom_read(tmdev->dev, "calib_backup");
> +	if (IS_ERR(data))
> +		return PTR_ERR(data);
> +
> +	for (i = 0; i < num_read; i++, s++)
> +		s->offset = data[i];
> +
> +	return 0;
> +}
> +
> +/* Temperature on y axis and ADC-code on x-axis */
> +static inline int code_to_mdegC(u32 adc_code, const struct tsens_sensor *s)
> +{
> +	u32 slope;

why unsigned?

> +	int offset;
> +
> +	slope = thermal_zone_get_slope(s->tzd);;

Please use one single ;

> +	offset = CAL_MDEGC - slope * s->offset;
> +
> +	return adc_code * slope + offset;
> +}
> +
> +static int get_temp_8960(struct tsens_device *tmdev, int id, int *temp)
> +{
> +	int ret;
> +	u32 code, trdy;
> +	const struct tsens_sensor *s = &tmdev->sensor[id];
> +	unsigned long timeout;
> +
> +	timeout = jiffies + usecs_to_jiffies(TIMEOUT_US);
> +	do {
> +		ret = regmap_read(tmdev->map, INT_STATUS_ADDR, &trdy);
> +		if (ret)
> +			return ret;
> +		if (!(trdy & TRDY_MASK))
> +			continue;
> +		ret = regmap_read(tmdev->map, s->status, &code);
> +		if (ret)
> +			return ret;
> +		*temp = code_to_mdegC(code, s);
> +		return 0;
> +	} while (time_before(jiffies, timeout));
> +
> +	return -ETIMEDOUT;
> +}
> +
> +const struct tsens_ops ops_8960 = {
> +	.init		= init_8960,
> +	.calibrate	= calibrate_8960,
> +	.get_temp	= get_temp_8960,
> +	.enable		= enable_8960,
> +	.disable	= disable_8960,
> +	.suspend	= suspend_8960,
> +	.resume		= resume_8960,
> +};
> +
> +const struct tsens_data data_8960 = {
> +	.num_sensors	= 11,
> +	.ops		= &ops_8960,
> +};
> diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
> index 99f3a6a..096f64d 100644
> --- a/drivers/thermal/qcom/tsens.c
> +++ b/drivers/thermal/qcom/tsens.c
> @@ -122,10 +122,10 @@ static int tsens_probe(struct platform_device *pdev)
>  	np = dev->of_node;
>  
>  	id = of_match_node(tsens_table, np);
> -	if (!id)
> -		return -EINVAL;
> -
> -	data = id->data;
> +	if (id)
> +		data = id->data;
> +	else
> +		data = &data_8960;
>  
>  	if (data->num_sensors <= 0) {
>  		dev_err(dev, "invalid number of sensors\n");
> diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
> index d4cfb5f..146d4f1 100644
> --- a/drivers/thermal/qcom/tsens.h
> +++ b/drivers/thermal/qcom/tsens.h
> @@ -87,6 +87,6 @@ void compute_intercept_slope(struct tsens_device *, u32 *, u32 *, u32);
>  int init_common(struct tsens_device *);
>  int get_temp_common(struct tsens_device *, int, int *);
>  
> -extern const struct tsens_data data_8916, data_8974;
> +extern const struct tsens_data data_8916, data_8974, data_8960;
>  
>  #endif /* __QCOM_TSENS_H__ */
> -- 
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
> of Code Aurora Forum, hosted by The Linux Foundation
>