* [PATCH 1/2] musb: sunxi: Add set_mode platform function
@ 2016-05-12 18:31 Hans de Goede
2016-05-12 18:31 ` [PATCH 2/2] musb: sunxi: Set state to A_WAIT_VRISE when enabling VBus Hans de Goede
0 siblings, 1 reply; 6+ messages in thread
From: Hans de Goede @ 2016-05-12 18:31 UTC (permalink / raw)
To: linux-arm-kernel
Move the mode handling to the platform_set_mode callback.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
drivers/usb/musb/sunxi.c | 30 +++++++++++++++++++-----------
1 file changed, 19 insertions(+), 11 deletions(-)
diff --git a/drivers/usb/musb/sunxi.c b/drivers/usb/musb/sunxi.c
index fdab423..2c33d9b 100644
--- a/drivers/usb/musb/sunxi.c
+++ b/drivers/usb/musb/sunxi.c
@@ -264,15 +264,6 @@ static int sunxi_musb_init(struct musb *musb)
if (ret)
goto error_unregister_notifier;
- if (musb->port_mode == MUSB_PORT_MODE_HOST) {
- ret = phy_power_on(glue->phy);
- if (ret)
- goto error_phy_exit;
- set_bit(SUNXI_MUSB_FL_PHY_ON, &glue->flags);
- /* Stop musb work from turning vbus off again */
- set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
- }
-
musb->isr = sunxi_musb_interrupt;
/* Stop the musb-core from doing runtime pm (not supported on sunxi) */
@@ -280,8 +271,6 @@ static int sunxi_musb_init(struct musb *musb)
return 0;
-error_phy_exit:
- phy_exit(glue->phy);
error_unregister_notifier:
if (musb->port_mode == MUSB_PORT_MODE_DUAL_ROLE)
extcon_unregister_notifier(glue->extcon, EXTCON_USB_HOST,
@@ -323,6 +312,24 @@ static int sunxi_musb_exit(struct musb *musb)
return 0;
}
+static int sunxi_set_mode(struct musb *musb, u8 mode)
+{
+ struct sunxi_glue *glue = dev_get_drvdata(musb->controller->parent);
+ int ret;
+
+ if (mode == MUSB_HOST) {
+ ret = phy_power_on(glue->phy);
+ if (ret)
+ return ret;
+
+ set_bit(SUNXI_MUSB_FL_PHY_ON, &glue->flags);
+ /* Stop musb work from turning vbus off again */
+ set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
+ }
+
+ return 0;
+}
+
static void sunxi_musb_enable(struct musb *musb)
{
struct sunxi_glue *glue = dev_get_drvdata(musb->controller->parent);
@@ -569,6 +576,7 @@ static const struct musb_platform_ops sunxi_musb_ops = {
.exit = sunxi_musb_exit,
.enable = sunxi_musb_enable,
.disable = sunxi_musb_disable,
+ .set_mode = sunxi_set_mode,
.fifo_offset = sunxi_musb_fifo_offset,
.ep_offset = sunxi_musb_ep_offset,
.busctl_offset = sunxi_musb_busctl_offset,
--
2.7.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 2/2] musb: sunxi: Set state to A_WAIT_VRISE when enabling VBus
2016-05-12 18:31 [PATCH 1/2] musb: sunxi: Add set_mode platform function Hans de Goede
@ 2016-05-12 18:31 ` Hans de Goede
2016-05-12 20:21 ` Sergei Shtylyov
2016-05-13 18:35 ` Bin Liu
0 siblings, 2 replies; 6+ messages in thread
From: Hans de Goede @ 2016-05-12 18:31 UTC (permalink / raw)
To: linux-arm-kernel
When the board is powering attached usb devices via the otg port
sometimes / on some devices it takes slightly too long for the VBus
detection code in phy-sun4i-usb.c to signal that VBus is high after
enabling VBus and the musb hardware signals a MUSB_INTR_VBUSERROR
interrupt.
This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
VBUSERROR interrupts, fixing connection issues in these cases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
drivers/usb/musb/sunxi.c | 8 +++++---
1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/drivers/usb/musb/sunxi.c b/drivers/usb/musb/sunxi.c
index 2c33d9b..2ee48fb 100644
--- a/drivers/usb/musb/sunxi.c
+++ b/drivers/usb/musb/sunxi.c
@@ -112,7 +112,7 @@ static void sunxi_musb_work(struct work_struct *work)
if (test_bit(SUNXI_MUSB_FL_HOSTMODE, &glue->flags)) {
set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
musb->xceiv->otg->default_a = 1;
- musb->xceiv->otg->state = OTG_STATE_A_IDLE;
+ musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
MUSB_HST_MODE(musb);
devctl |= MUSB_DEVCTL_SESSION;
} else {
@@ -145,9 +145,10 @@ static void sunxi_musb_set_vbus(struct musb *musb, int is_on)
{
struct sunxi_glue *glue = dev_get_drvdata(musb->controller->parent);
- if (is_on)
+ if (is_on) {
set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
- else
+ musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
+ } else
clear_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
schedule_work(&glue->work);
@@ -325,6 +326,7 @@ static int sunxi_set_mode(struct musb *musb, u8 mode)
set_bit(SUNXI_MUSB_FL_PHY_ON, &glue->flags);
/* Stop musb work from turning vbus off again */
set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
+ musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
}
return 0;
--
2.7.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 2/2] musb: sunxi: Set state to A_WAIT_VRISE when enabling VBus
2016-05-12 18:31 ` [PATCH 2/2] musb: sunxi: Set state to A_WAIT_VRISE when enabling VBus Hans de Goede
@ 2016-05-12 20:21 ` Sergei Shtylyov
2016-05-13 18:35 ` Bin Liu
1 sibling, 0 replies; 6+ messages in thread
From: Sergei Shtylyov @ 2016-05-12 20:21 UTC (permalink / raw)
To: linux-arm-kernel
Hello.
On 05/12/2016 09:31 PM, Hans de Goede wrote:
> When the board is powering attached usb devices via the otg port
> sometimes / on some devices it takes slightly too long for the VBus
I think it's either VBUS or Vbus, not this strange spelling.
> detection code in phy-sun4i-usb.c to signal that VBus is high after
> enabling VBus and the musb hardware signals a MUSB_INTR_VBUSERROR
> interrupt.
>
> This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
> making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
> VBUSERROR interrupts, fixing connection issues in these cases.
>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
> drivers/usb/musb/sunxi.c | 8 +++++---
> 1 file changed, 5 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/usb/musb/sunxi.c b/drivers/usb/musb/sunxi.c
> index 2c33d9b..2ee48fb 100644
> --- a/drivers/usb/musb/sunxi.c
> +++ b/drivers/usb/musb/sunxi.c
> @@ -112,7 +112,7 @@ static void sunxi_musb_work(struct work_struct *work)
> if (test_bit(SUNXI_MUSB_FL_HOSTMODE, &glue->flags)) {
> set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
> musb->xceiv->otg->default_a = 1;
> - musb->xceiv->otg->state = OTG_STATE_A_IDLE;
> + musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
> MUSB_HST_MODE(musb);
> devctl |= MUSB_DEVCTL_SESSION;
> } else {
> @@ -145,9 +145,10 @@ static void sunxi_musb_set_vbus(struct musb *musb, int is_on)
> {
> struct sunxi_glue *glue = dev_get_drvdata(musb->controller->parent);
>
> - if (is_on)
> + if (is_on) {
> set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
> - else
> + musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
> + } else
> clear_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
CodingStyle, all *if* branches should use {} if one uses {}.
[...]
MBR, Sergei
^ permalink raw reply [flat|nested] 6+ messages in thread* [PATCH 2/2] musb: sunxi: Set state to A_WAIT_VRISE when enabling VBus
2016-05-12 18:31 ` [PATCH 2/2] musb: sunxi: Set state to A_WAIT_VRISE when enabling VBus Hans de Goede
2016-05-12 20:21 ` Sergei Shtylyov
@ 2016-05-13 18:35 ` Bin Liu
2016-05-14 9:07 ` [linux-sunxi] " Hans de Goede
1 sibling, 1 reply; 6+ messages in thread
From: Bin Liu @ 2016-05-13 18:35 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Thu, May 12, 2016 at 08:31:09PM +0200, Hans de Goede wrote:
> When the board is powering attached usb devices via the otg port
> sometimes / on some devices it takes slightly too long for the VBus
> detection code in phy-sun4i-usb.c to signal that VBus is high after
> enabling VBus and the musb hardware signals a MUSB_INTR_VBUSERROR
> interrupt.
>
> This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
> making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
> VBUSERROR interrupts, fixing connection issues in these cases.
>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
> drivers/usb/musb/sunxi.c | 8 +++++---
> 1 file changed, 5 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/usb/musb/sunxi.c b/drivers/usb/musb/sunxi.c
> index 2c33d9b..2ee48fb 100644
> --- a/drivers/usb/musb/sunxi.c
> +++ b/drivers/usb/musb/sunxi.c
> @@ -112,7 +112,7 @@ static void sunxi_musb_work(struct work_struct *work)
> if (test_bit(SUNXI_MUSB_FL_HOSTMODE, &glue->flags)) {
> set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
> musb->xceiv->otg->default_a = 1;
> - musb->xceiv->otg->state = OTG_STATE_A_IDLE;
> + musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
> MUSB_HST_MODE(musb);
> devctl |= MUSB_DEVCTL_SESSION;
> } else {
> @@ -145,9 +145,10 @@ static void sunxi_musb_set_vbus(struct musb *musb, int is_on)
> {
> struct sunxi_glue *glue = dev_get_drvdata(musb->controller->parent);
>
> - if (is_on)
> + if (is_on) {
> set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
> - else
> + musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
Why this has to be set in both sunxi_musb_work() and here? Only setting
it in the work is not efficient?
Regards,
-Bin.
> + } else
> clear_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
>
> schedule_work(&glue->work);
> @@ -325,6 +326,7 @@ static int sunxi_set_mode(struct musb *musb, u8 mode)
> set_bit(SUNXI_MUSB_FL_PHY_ON, &glue->flags);
> /* Stop musb work from turning vbus off again */
> set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
> + musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
> }
>
> return 0;
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 6+ messages in thread* [linux-sunxi] Re: [PATCH 2/2] musb: sunxi: Set state to A_WAIT_VRISE when enabling VBus
2016-05-13 18:35 ` Bin Liu
@ 2016-05-14 9:07 ` Hans de Goede
2016-05-15 4:22 ` Bin Liu
0 siblings, 1 reply; 6+ messages in thread
From: Hans de Goede @ 2016-05-14 9:07 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On 13-05-16 20:35, Bin Liu wrote:
> Hi,
>
> On Thu, May 12, 2016 at 08:31:09PM +0200, Hans de Goede wrote:
>> When the board is powering attached usb devices via the otg port
>> sometimes / on some devices it takes slightly too long for the VBus
>> detection code in phy-sun4i-usb.c to signal that VBus is high after
>> enabling VBus and the musb hardware signals a MUSB_INTR_VBUSERROR
>> interrupt.
>>
>> This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
>> making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
>> VBUSERROR interrupts, fixing connection issues in these cases.
>>
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>> ---
>> drivers/usb/musb/sunxi.c | 8 +++++---
>> 1 file changed, 5 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/usb/musb/sunxi.c b/drivers/usb/musb/sunxi.c
>> index 2c33d9b..2ee48fb 100644
>> --- a/drivers/usb/musb/sunxi.c
>> +++ b/drivers/usb/musb/sunxi.c
>> @@ -112,7 +112,7 @@ static void sunxi_musb_work(struct work_struct *work)
>> if (test_bit(SUNXI_MUSB_FL_HOSTMODE, &glue->flags)) {
>> set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
>> musb->xceiv->otg->default_a = 1;
>> - musb->xceiv->otg->state = OTG_STATE_A_IDLE;
>> + musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
>> MUSB_HST_MODE(musb);
>> devctl |= MUSB_DEVCTL_SESSION;
>> } else {
>> @@ -145,9 +145,10 @@ static void sunxi_musb_set_vbus(struct musb *musb, int is_on)
>> {
>> struct sunxi_glue *glue = dev_get_drvdata(musb->controller->parent);
>>
>> - if (is_on)
>> + if (is_on) {
>> set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
>> - else
>> + musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
>
> Why this has to be set in both sunxi_musb_work() and here? Only setting
> it in the work is not efficient?
Different code paths, sunxi_musb_work sets it when the id pin changes
(gets pulled low), this function gets called by musb_core in response
to a session-request interrupt.
Regards,
Hans
>
> Regards,
> -Bin.
>
>> + } else
>> clear_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
>>
>> schedule_work(&glue->work);
>> @@ -325,6 +326,7 @@ static int sunxi_set_mode(struct musb *musb, u8 mode)
>> set_bit(SUNXI_MUSB_FL_PHY_ON, &glue->flags);
>> /* Stop musb work from turning vbus off again */
>> set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
>> + musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
>> }
>>
>> return 0;
>> --
>> 2.7.4
>>
^ permalink raw reply [flat|nested] 6+ messages in thread* [linux-sunxi] Re: [PATCH 2/2] musb: sunxi: Set state to A_WAIT_VRISE when enabling VBus
2016-05-14 9:07 ` [linux-sunxi] " Hans de Goede
@ 2016-05-15 4:22 ` Bin Liu
0 siblings, 0 replies; 6+ messages in thread
From: Bin Liu @ 2016-05-15 4:22 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On Sat, May 14, 2016 at 11:07:51AM +0200, Hans de Goede wrote:
> Hi,
>
> On 13-05-16 20:35, Bin Liu wrote:
> >Hi,
> >
> >On Thu, May 12, 2016 at 08:31:09PM +0200, Hans de Goede wrote:
> >>When the board is powering attached usb devices via the otg port
> >>sometimes / on some devices it takes slightly too long for the VBus
> >>detection code in phy-sun4i-usb.c to signal that VBus is high after
> >>enabling VBus and the musb hardware signals a MUSB_INTR_VBUSERROR
> >>interrupt.
> >>
> >>This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
> >>making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
> >>VBUSERROR interrupts, fixing connection issues in these cases.
> >>
> >>Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> >>---
> >> drivers/usb/musb/sunxi.c | 8 +++++---
> >> 1 file changed, 5 insertions(+), 3 deletions(-)
> >>
> >>diff --git a/drivers/usb/musb/sunxi.c b/drivers/usb/musb/sunxi.c
> >>index 2c33d9b..2ee48fb 100644
> >>--- a/drivers/usb/musb/sunxi.c
> >>+++ b/drivers/usb/musb/sunxi.c
> >>@@ -112,7 +112,7 @@ static void sunxi_musb_work(struct work_struct *work)
> >> if (test_bit(SUNXI_MUSB_FL_HOSTMODE, &glue->flags)) {
> >> set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
> >> musb->xceiv->otg->default_a = 1;
> >>- musb->xceiv->otg->state = OTG_STATE_A_IDLE;
> >>+ musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
> >> MUSB_HST_MODE(musb);
> >> devctl |= MUSB_DEVCTL_SESSION;
> >> } else {
> >>@@ -145,9 +145,10 @@ static void sunxi_musb_set_vbus(struct musb *musb, int is_on)
> >> {
> >> struct sunxi_glue *glue = dev_get_drvdata(musb->controller->parent);
> >>
> >>- if (is_on)
> >>+ if (is_on) {
> >> set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
> >>- else
> >>+ musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
> >
> >Why this has to be set in both sunxi_musb_work() and here? Only setting
> >it in the work is not efficient?
>
> Different code paths, sunxi_musb_work sets it when the id pin changes
> (gets pulled low), this function gets called by musb_core in response
> to a session-request interrupt.
Ok, I see what I missed. An interrupt could happen right after
_set_vbus() but before _musb_work().
Regards,
-Bin.
>
> Regards,
>
> Hans
>
>
> >
> >Regards,
> >-Bin.
> >
> >>+ } else
> >> clear_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
> >>
> >> schedule_work(&glue->work);
> >>@@ -325,6 +326,7 @@ static int sunxi_set_mode(struct musb *musb, u8 mode)
> >> set_bit(SUNXI_MUSB_FL_PHY_ON, &glue->flags);
> >> /* Stop musb work from turning vbus off again */
> >> set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
> >>+ musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
> >> }
> >>
> >> return 0;
> >>--
> >>2.7.4
> >>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2016-05-15 4:22 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-05-12 18:31 [PATCH 1/2] musb: sunxi: Add set_mode platform function Hans de Goede
2016-05-12 18:31 ` [PATCH 2/2] musb: sunxi: Set state to A_WAIT_VRISE when enabling VBus Hans de Goede
2016-05-12 20:21 ` Sergei Shtylyov
2016-05-13 18:35 ` Bin Liu
2016-05-14 9:07 ` [linux-sunxi] " Hans de Goede
2016-05-15 4:22 ` Bin Liu
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).