[PATCH v2 1/2] musb: sunxi: Add set_mode platform function

[PATCH v2 1/2] musb: sunxi: Add set_mode platform function

[Hans de Goede]

Move the mode handling to the platform_set_mode callback.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Changes in v2:
-No changes
---
 drivers/usb/musb/sunxi.c | 30 +++++++++++++++++++-----------
 1 file changed, 19 insertions(+), 11 deletions(-)

diff --git a/drivers/usb/musb/sunxi.c b/drivers/usb/musb/sunxi.c
index fdab423..2c33d9b 100644
--- a/drivers/usb/musb/sunxi.c
+++ b/drivers/usb/musb/sunxi.c
@@ -264,15 +264,6 @@ static int sunxi_musb_init(struct musb *musb)
 	if (ret)
 		goto error_unregister_notifier;
 
-	if (musb->port_mode == MUSB_PORT_MODE_HOST) {
-		ret = phy_power_on(glue->phy);
-		if (ret)
-			goto error_phy_exit;
-		set_bit(SUNXI_MUSB_FL_PHY_ON, &glue->flags);
-		/* Stop musb work from turning vbus off again */
-		set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
-	}
-
 	musb->isr = sunxi_musb_interrupt;
 
 	/* Stop the musb-core from doing runtime pm (not supported on sunxi) */
@@ -280,8 +271,6 @@ static int sunxi_musb_init(struct musb *musb)
 
 	return 0;
 
-error_phy_exit:
-	phy_exit(glue->phy);
 error_unregister_notifier:
 	if (musb->port_mode == MUSB_PORT_MODE_DUAL_ROLE)
 		extcon_unregister_notifier(glue->extcon, EXTCON_USB_HOST,
@@ -323,6 +312,24 @@ static int sunxi_musb_exit(struct musb *musb)
 	return 0;
 }
 
+static int sunxi_set_mode(struct musb *musb, u8 mode)
+{
+	struct sunxi_glue *glue = dev_get_drvdata(musb->controller->parent);
+	int ret;
+
+	if (mode == MUSB_HOST) {
+		ret = phy_power_on(glue->phy);
+		if (ret)
+			return ret;
+
+		set_bit(SUNXI_MUSB_FL_PHY_ON, &glue->flags);
+		/* Stop musb work from turning vbus off again */
+		set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
+	}
+
+	return 0;
+}
+
 static void sunxi_musb_enable(struct musb *musb)
 {
 	struct sunxi_glue *glue = dev_get_drvdata(musb->controller->parent);
@@ -569,6 +576,7 @@ static const struct musb_platform_ops sunxi_musb_ops = {
 	.exit		= sunxi_musb_exit,
 	.enable		= sunxi_musb_enable,
 	.disable	= sunxi_musb_disable,
+	.set_mode	= sunxi_set_mode,
 	.fifo_offset	= sunxi_musb_fifo_offset,
 	.ep_offset	= sunxi_musb_ep_offset,
 	.busctl_offset	= sunxi_musb_busctl_offset,
-- 
2.7.4

[PATCH v2 2/2] musb: sunxi: Set state to A_WAIT_VRISE when enabling Vbus

[Hans de Goede]

When the board is powering attached usb devices via the otg port
sometimes / on some devices it takes slightly too long for the Vbus
detection code in phy-sun4i-usb.c to signal that Vbus is high after
enabling Vbus and the musb hardware signals a MUSB_INTR_VBUSERROR
interrupt.

This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
VBUSERROR interrupts, fixing connection issues in these cases.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Changes in v2:
-Use curly-braces in both branches of if-else
---
 drivers/usb/musb/sunxi.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/musb/sunxi.c b/drivers/usb/musb/sunxi.c
index 2c33d9b..e7d4617 100644
--- a/drivers/usb/musb/sunxi.c
+++ b/drivers/usb/musb/sunxi.c
@@ -112,7 +112,7 @@ static void sunxi_musb_work(struct work_struct *work)
 		if (test_bit(SUNXI_MUSB_FL_HOSTMODE, &glue->flags)) {
 			set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
 			musb->xceiv->otg->default_a = 1;
-			musb->xceiv->otg->state = OTG_STATE_A_IDLE;
+			musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
 			MUSB_HST_MODE(musb);
 			devctl |= MUSB_DEVCTL_SESSION;
 		} else {
@@ -145,10 +145,12 @@ static void sunxi_musb_set_vbus(struct musb *musb, int is_on)
 {
 	struct sunxi_glue *glue = dev_get_drvdata(musb->controller->parent);
 
-	if (is_on)
+	if (is_on) {
 		set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
-	else
+		musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
+	} else {
 		clear_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
+	}
 
 	schedule_work(&glue->work);
 }
@@ -325,6 +327,7 @@ static int sunxi_set_mode(struct musb *musb, u8 mode)
 		set_bit(SUNXI_MUSB_FL_PHY_ON, &glue->flags);
 		/* Stop musb work from turning vbus off again */
 		set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
+		musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
 	}
 
 	return 0;
-- 
2.7.4

[PATCH v2 2/2] musb: sunxi: Set state to A_WAIT_VRISE when enabling Vbus

[Bin Liu]

On Sat, May 14, 2016 at 02:45:05PM +0200, Hans de Goede wrote:
> When the board is powering attached usb devices via the otg port
> sometimes / on some devices it takes slightly too long for the Vbus
> detection code in phy-sun4i-usb.c to signal that Vbus is high after
> enabling Vbus and the musb hardware signals a MUSB_INTR_VBUSERROR
> interrupt.
> 
> This commit sets the otg state to A_WAIT_VRISE upon enabling Vbus
> making musb_stage0_irq() ignore the first VBUSERR_RETRY_COUNT
> VBUSERROR interrupts, fixing connection issues in these cases.
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Signed-off-by: Bin Liu <b-liu@ti.com>

Regards,
-Bin.

[PATCH v2 1/2] musb: sunxi: Add set_mode platform function

[Bin Liu]

On Sat, May 14, 2016 at 02:45:04PM +0200, Hans de Goede wrote:
> Move the mode handling to the platform_set_mode callback.
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Signed-off-by: Bin Liu <b-liu@ti.com>

Regards,
-Bin.

[PATCH v2 1/2] musb: sunxi: Add set_mode platform function

[Bin Liu]

Hi,

On Mon, May 16, 2016 at 03:11:34PM -0500, Bin Liu wrote:
> On Sat, May 14, 2016 at 02:45:04PM +0200, Hans de Goede wrote:
> > Move the mode handling to the platform_set_mode callback.
> > 
> > Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> 
> Signed-off-by: Bin Liu <b-liu@ti.com>

I revised the subject prefix to "usb: musb: sunxi: ..." for both
patches.

Regards,
-Bin.

> 
> Regards,
> -Bin.