[PATCH] ARM: at91: Add DT support for Olimex SAM9-L9260 board.

[robh@kernel.org (Rob Herring)]

On Wed, May 18, 2016 at 06:02:46PM +0530, Raashid Muhammed wrote:
> From: Raashid Muhammed <raashidmuhammed@zilogic.com>
> 
> sam9-l9260 is a low cost board designed by Olimex.
> 
> More infomation is available at:
> https://www.olimex.com/Products/ARM/Atmel/SAM9-L9260/
> 
> Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
> Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
> ---
>  .../devicetree/bindings/arm/olimex-at91.txt        |   6 ++
>  arch/arm/boot/dts/Makefile                         |   1 +
>  arch/arm/boot/dts/sam9-l9260.dts                   | 108 +++++++++++++++++++++
>  3 files changed, 115 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/arm/olimex-at91.txt
>  create mode 100644 arch/arm/boot/dts/sam9-l9260.dts
> 
> diff --git a/Documentation/devicetree/bindings/arm/olimex-at91.txt b/Documentation/devicetree/bindings/arm/olimex-at91.txt
> new file mode 100644
> index 0000000..0587d63
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/olimex-at91.txt
> @@ -0,0 +1,6 @@
> +Olimex AT91 Device Tree Bindings
> +--------------------------------

There's not an existing at91 or olimex file this would fit into? We 
don't need 1 file per board.

> +
> +SAM9-L9260 Board
> +Required root node properties:
> +    - compatible = "olimex,sam9-l9260", "atmel,at91sam9260";
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 95c1923..ae3b50f 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -19,6 +19,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
> 	usb_a9260.dtb \
> 	at91sam9261ek.dtb \
> 	at91sam9263ek.dtb \
> +	sam9-l9260.dtb \
> 	tny_a9263.dtb \
> 	usb_a9263.dtb \
> 	at91-foxg20.dtb \
> diff --git a/arch/arm/boot/dts/sam9-l9260.dts b/arch/arm/boot/dts/sam9-l9260.dts
> new file mode 100644
> index 0000000..3ddf7af
> --- /dev/null
> +++ b/arch/arm/boot/dts/sam9-l9260.dts
> @@ -0,0 +1,108 @@
> +/*
> + * sam9-l9260.dts - Device Tree file for Olimex SAM9-L9260 board
> + *
> + *  Copyright (C) 2016 Raashid Muhammed <raashidmuhammed@zilogic.com>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +/dts-v1/;
> +#include "at91sam9260.dtsi"
> +
> +/ {
> +	model = "Olimex sam9-l9260";
> +	compatible = "olimex,sam9-l9260", "atmel,at91sam9260", "atmel,at91sam9";
> +
> +	chosen {
> +		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";

use stdout-path instead of console on the command line. Actually, you 
should then drop the rest of the bootargs. They are all user specific.

> +	 };
> +
> +	 memory {
> +		reg = <0x20000000 0x4000000>;
> +	 };
> +
> +	 clocks {
> +		slow_xtal {
> +			clock-frequency = <32768>;
> +		};
> +
> +		main_xtal {
> +			clock-frequency = <18432000>;
> +		};
> +	 };
> +
> +	 ahb {
> +		apb {
> +			dbgu: serial at fffff200 {
> +				status = "okay";
> +			 };
> +
> +			macb0: ethernet at fffc4000 {
> +				phy-mode = "mii";
> +				status = "okay";
> +			 };
> +
> +			spi0: spi at fffc8000 {
> +				status = "okay";
> +				cs-gpios = <&pioC 11 0>, <0>, <0>, <0>;
> +				mtd_dataflash at 0 {
> +					compatible = "atmel,at45", "atmel,dataflash";
> +					spi-max-frequency = <15000000>;
> +					reg = <0>;
> +				};
> +			};
> +
> +			mmc0: mmc at fffa8000 {
> +				pinctrl-0 = <
> +					&pinctrl_board_mmc0
> +					&pinctrl_mmc0_clk
> +					&pinctrl_mmc0_slot1_cmd_dat0
> +					&pinctrl_mmc0_slot1_dat1_3>;
> +				status = "okay";
> +				slot at 1 {
> +					reg = <1>;
> +					bus-width = <4>;
> +					cd-gpios = <&pioC 8 GPIO_ACTIVE_HIGH>;
> +					wp-gpios = <&pioC 4 GPIO_ACTIVE_HIGH>;
> +				};
> +			};
> +
> +			pinctrl at fffff400 {
> +				mmc0 {
> +					pinctrl_board_mmc0: mmc0-board {
> +						atmel,pins =
> +							<AT91_PIOC 8 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH	/* PC08 gpio CD pin pull up and deglitch */
> +							 AT91_PIOC 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;	/* PC04 gpio WP pin pull up */
> +					};
> +				};
> +			};
> +
> +
> +		 };
> +
> +		 usb0: ohci at 00500000 {

Drop the leading 0. You'll need to fixup the base dts.

> +		       status = "okay";
> +		 };
> +
> +		 nand0: nand at 40000000 {
> +		       nand-bus-width = <8>;
> +		       nand-ecc-mode = "soft";
> +		       nand-on-flash-bbt = <1>;
> +		       status = "okay";
> +		 };
> +	 };
> +
> +	 i2c at 0 {
> +		status = "okay";
> +	 };
> +
> +	 leds {
> +		compatible = "gpio-leds";
> +
> +		b0 {
> +			label = "b0";
> +			gpios = <&pioA 6 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +
> +	};
> +};
> --
> 2.1.4
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel