linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: stephen.boyd@linaro.org (Stephen Boyd)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 06/21] usb: chipidea: Initialize and reinitialize phy later
Date: Sun, 26 Jun 2016 00:28:23 -0700	[thread overview]
Message-ID: <20160626072838.28082-7-stephen.boyd@linaro.org> (raw)
In-Reply-To: <20160626072838.28082-1-stephen.boyd@linaro.org>

The ULPI phy on qcom platforms needs to be initialized and
powered on after a USB reset and before we toggle the run/stop
bit. Otherwise, the phy locks up and doesn't work properly. Move
the phy initialization to a later point, and shut it down outside
of driver remove so that the phy state is properly managed across
role switches.

Cc: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
 drivers/usb/chipidea/ci.h   |  3 ++-
 drivers/usb/chipidea/core.c | 23 ++++++++++-------------
 drivers/usb/chipidea/host.c |  5 ++---
 drivers/usb/chipidea/udc.c  |  2 ++
 4 files changed, 16 insertions(+), 17 deletions(-)

diff --git a/drivers/usb/chipidea/ci.h b/drivers/usb/chipidea/ci.h
index cd414559040f..f87805235caa 100644
--- a/drivers/usb/chipidea/ci.h
+++ b/drivers/usb/chipidea/ci.h
@@ -431,7 +431,8 @@ u8 hw_port_test_get(struct ci_hdrc *ci);
 int hw_wait_reg(struct ci_hdrc *ci, enum ci_hw_regs reg, u32 mask,
 				u32 value, unsigned int timeout_ms);
 
-void ci_platform_configure(struct ci_hdrc *ci);
+void ci_usb_phy_exit(struct ci_hdrc *ci);
+int ci_platform_configure(struct ci_hdrc *ci);
 
 int dbg_create_files(struct ci_hdrc *ci);
 
diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index 01390e02ee53..a01611c7f815 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -359,7 +359,7 @@ static int _ci_usb_phy_init(struct ci_hdrc *ci)
  * interfaces
  * @ci: the controller
  */
-static void ci_usb_phy_exit(struct ci_hdrc *ci)
+void ci_usb_phy_exit(struct ci_hdrc *ci)
 {
 	if (ci->phy) {
 		phy_power_off(ci->phy);
@@ -412,9 +412,14 @@ static int ci_usb_phy_init(struct ci_hdrc *ci)
  * @ci: the controller
  *
  */
-void ci_platform_configure(struct ci_hdrc *ci)
+int ci_platform_configure(struct ci_hdrc *ci)
 {
 	bool is_device_mode, is_host_mode;
+	int ret;
+
+	ret = ci_usb_phy_init(ci);
+	if (ret)
+		return ret;
 
 	is_device_mode = hw_read(ci, OP_USBMODE, USBMODE_CM) == USBMODE_CM_DC;
 	is_host_mode = hw_read(ci, OP_USBMODE, USBMODE_CM) == USBMODE_CM_HC;
@@ -453,6 +458,8 @@ void ci_platform_configure(struct ci_hdrc *ci)
 			hw_write(ci, OP_BURSTSIZE, RX_BURST_MASK,
 				ci->platdata->rx_burst_size);
 	}
+
+	return 0;
 }
 
 /**
@@ -511,9 +518,7 @@ int hw_device_reset(struct ci_hdrc *ci)
 		return -ENODEV;
 	}
 
-	ci_platform_configure(ci);
-
-	return 0;
+	return ci_platform_configure(ci);
 }
 
 static irqreturn_t ci_irq(int irq, void *data)
@@ -917,12 +922,6 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 			ci->usb_phy = NULL;
 	}
 
-	ret = ci_usb_phy_init(ci);
-	if (ret) {
-		dev_err(dev, "unable to init phy: %d\n", ret);
-		return ret;
-	}
-
 	ci->hw_bank.phys = res->start;
 
 	ci->irq = platform_get_irq(pdev, 0);
@@ -1025,7 +1024,6 @@ static int ci_hdrc_probe(struct platform_device *pdev)
 stop:
 	ci_role_destroy(ci);
 deinit_phy:
-	ci_usb_phy_exit(ci);
 
 	return ret;
 }
@@ -1044,7 +1042,6 @@ static int ci_hdrc_remove(struct platform_device *pdev)
 	ci_extcon_unregister(ci);
 	ci_role_destroy(ci);
 	ci_hdrc_enter_lpm(ci, true);
-	ci_usb_phy_exit(ci);
 
 	return 0;
 }
diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c
index 053bac9d983c..523c155daea8 100644
--- a/drivers/usb/chipidea/host.c
+++ b/drivers/usb/chipidea/host.c
@@ -87,9 +87,7 @@ static int ehci_ci_reset(struct usb_hcd *hcd)
 	if (ret)
 		return ret;
 
-	ci_platform_configure(ci);
-
-	return ret;
+	return ci_platform_configure(ci);
 }
 
 static const struct ehci_driver_overrides ehci_ci_overrides = {
@@ -186,6 +184,7 @@ static void host_stop(struct ci_hdrc *ci)
 	if (hcd) {
 		usb_remove_hcd(hcd);
 		usb_put_hcd(hcd);
+		ci_usb_phy_exit(ci);
 		if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci) &&
 			(ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON))
 				regulator_disable(ci->platdata->reg_vbus);
diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c
index 065f5d97aa67..8f44e2d1e0c0 100644
--- a/drivers/usb/chipidea/udc.c
+++ b/drivers/usb/chipidea/udc.c
@@ -1534,6 +1534,7 @@ static int ci_udc_vbus_session(struct usb_gadget *_gadget, int is_active)
 			if (ci->driver)
 				ci->driver->disconnect(&ci->gadget);
 			hw_device_state(ci, 0);
+			ci_usb_phy_exit(ci);
 			if (ci->platdata->notify_event)
 				ci->platdata->notify_event(ci,
 				CI_HDRC_CONTROLLER_STOPPED_EVENT);
@@ -1794,6 +1795,7 @@ static int ci_udc_stop(struct usb_gadget *gadget)
 			ci->platdata->notify_event(ci,
 			CI_HDRC_CONTROLLER_STOPPED_EVENT);
 		spin_unlock_irqrestore(&ci->lock, flags);
+		ci_usb_phy_exit(ci);
 		_gadget_stop_activity(&ci->gadget);
 		spin_lock_irqsave(&ci->lock, flags);
 		pm_runtime_put(&ci->gadget.dev);
-- 
2.9.0.rc2.8.ga28705d

  parent reply	other threads:[~2016-06-26  7:28 UTC|newest]

Thread overview: 91+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-06-26  7:28 [PATCH 00/21] Support qcom's HSIC USB and rewrite USB2 HS phy support Stephen Boyd
2016-06-26  7:28 ` [PATCH 01/21] of: device: Support loading a module with OF based modalias Stephen Boyd
2016-06-28  4:17   ` Bjorn Andersson
2016-06-26  7:28 ` [PATCH 02/21] usb: ulpi: Support device discovery via DT Stephen Boyd
2016-06-27  4:21   ` kbuild test robot
2016-06-27 14:34   ` Heikki Krogerus
2016-06-27 22:10     ` Stephen Boyd
2016-06-28 11:42       ` Heikki Krogerus
2016-06-28 18:27         ` Stephen Boyd
2016-06-29  1:53         ` Peter Chen
2016-06-28 20:56   ` Rob Herring
2016-06-28 22:09     ` Stephen Boyd
2016-07-01  0:59       ` Rob Herring
2016-07-06  6:16         ` Stephen Boyd
2016-06-26  7:28 ` [PATCH 03/21] usb: ulpi: Avoid reading/writing in device creation with OF devices Stephen Boyd
2016-06-26  7:28 ` [PATCH 04/21] usb: chipidea: Only read/write OTGSC from one place Stephen Boyd
2016-06-27  8:04   ` Jun Li
2016-06-27 19:07     ` Stephen Boyd
2016-06-28  9:36       ` Peter Chen
2016-06-28 22:10         ` Stephen Boyd
2016-06-26  7:28 ` [PATCH 05/21] usb: chipidea: Handle extcon events properly Stephen Boyd
2016-06-28 10:01   ` Peter Chen
2016-06-26  7:28 ` Stephen Boyd [this message]
2016-06-29  2:30   ` [PATCH 06/21] usb: chipidea: Initialize and reinitialize phy later Peter Chen
2016-06-30  1:23     ` Stephen Boyd
2016-06-30  1:22       ` Peter Chen
2016-06-26  7:28 ` [PATCH 07/21] usb: chipidea: Notify of reset when switching into host mode Stephen Boyd
2016-06-26  7:28 ` [PATCH 08/21] usb: chipidea: Kick OTG state machine for AVVIS with vbus extcon Stephen Boyd
2016-06-29  3:09   ` Peter Chen
2016-06-30  1:19     ` Stephen Boyd
2016-06-30  1:26       ` Peter Chen
2016-06-30  1:50         ` Jun Li
2016-06-26  7:28 ` [PATCH 09/21] usb: chipidea: Add support for ULPI PHY bus Stephen Boyd
2016-06-29  6:26   ` Peter Chen
2016-06-30  1:29     ` Stephen Boyd
2016-06-26  7:28 ` [PATCH 10/21] usb: chipidea: msm: Rely on core to override AHBBURST Stephen Boyd
2016-06-29  6:32   ` Peter Chen
2016-06-29 18:59     ` Stephen Boyd
2016-06-30  1:18       ` Peter Chen
2016-06-30  1:41         ` Stephen Boyd
2016-06-26  7:28 ` [PATCH 11/21] usb: chipidea: msm: Use hw_write_id_reg() instead of writel directly Stephen Boyd
2016-06-29  6:37   ` Peter Chen
2016-06-26  7:28 ` [PATCH 12/21] usb: chipidea: msm: Keep device runtime enabled Stephen Boyd
2016-06-29  6:46   ` Peter Chen
2016-06-30  0:43     ` Stephen Boyd
2016-06-30  1:39       ` Peter Chen
2016-06-30 20:30         ` Stephen Boyd
2016-07-01  3:20           ` Peter Chen
2016-06-26  7:28 ` [PATCH 13/21] usb: chipidea: msm: Allow core to get usb phy Stephen Boyd
2016-06-29  6:48   ` Peter Chen
2016-06-29 11:34     ` Peter Chen
2016-06-29 19:31       ` Stephen Boyd
2016-06-30  1:43         ` Peter Chen
2016-06-26  7:28 ` [PATCH 14/21] usb: chipidea: msm: Add proper clk and reset support Stephen Boyd
2016-06-29  7:02   ` Peter Chen
2016-06-26  7:28 ` [PATCH 15/21] usb: chipidea: msm: Mux over secondary phy at the right time Stephen Boyd
2016-06-28  4:51   ` Bjorn Andersson
2016-06-28  8:39     ` Stephen Boyd
2016-06-29  8:08   ` Peter Chen
2016-06-29 19:28     ` Stephen Boyd
2016-06-30  1:52       ` Peter Chen
2016-06-30  1:35     ` Stephen Boyd
2016-06-26  7:28 ` [PATCH 16/21] usb: chipidea: msm: Restore wrapper settings after reset Stephen Boyd
2016-06-29  8:26   ` Peter Chen
2016-06-29 19:13     ` Stephen Boyd
2016-06-30  8:54       ` Peter Chen
2016-06-30 16:24         ` Stephen Boyd
2016-06-26  7:28 ` [PATCH 17/21] usb: chipidea: msm: Make platform data driver local instead of global Stephen Boyd
2016-06-29 11:29   ` Peter Chen
2016-06-29 19:17     ` Stephen Boyd
2016-06-30  9:08       ` Peter Chen
2016-06-26  7:28 ` [PATCH 18/21] usb: chipidea: msm: Add reset controller for PHY POR bit Stephen Boyd
2016-06-27  3:41   ` kbuild test robot
2016-06-27  4:51   ` kbuild test robot
2016-06-27  7:50   ` kbuild test robot
2016-06-28  1:27     ` Stephen Boyd
2016-06-29 11:45   ` Peter Chen
2016-06-26  7:28 ` [PATCH 19/21] usb: chipidea: msm: Be silent on probe defer errors Stephen Boyd
2016-06-30  1:06   ` Peter Chen
2016-06-30  1:26     ` Stephen Boyd
2016-06-26  7:28 ` [PATCH 20/21] phy: Add support for Qualcomm's USB HSIC phy Stephen Boyd
2016-06-28  8:49   ` Neil Armstrong
2016-06-28 21:58     ` Stephen Boyd
2016-06-29  9:16       ` Neil Armstrong
2016-06-29 18:54         ` Stephen Boyd
2016-06-26  7:28 ` [PATCH 21/21] phy: Add support for Qualcomm's USB HS phy Stephen Boyd
2016-06-28  3:09 ` [PATCH 00/21] Support qcom's HSIC USB and rewrite USB2 HS phy support John Stultz
2016-06-28  8:34   ` Stephen Boyd
2016-07-02  6:03     ` John Stultz
2016-07-05 19:22       ` Stephen Boyd
2016-07-05 19:33         ` John Stultz

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20160626072838.28082-7-stephen.boyd@linaro.org \
    --to=stephen.boyd@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).